Search NASA⌕ Search

SEARCH · Search NASA

Results for “low conductivity materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Ultralow Thermal Conductivity and Thermoelectric Properties of Rb 2 Bi 8 Se 13

Complex bismuth chalcogenides are narrow band gap semiconductors with intrinsic low thermal conductivity, which exhibit high potential as highly efficient thermoelectric materials. Here, we assess the basic thermoelectric properties of polycrystalline Rb 2 Bi 8 Se 13 in the temperature range 300-823 K as well as performance-optimizing strategies. We find that the as-made bulk samples are single phase with the monoclinic crystal structure (P2 1 /m) and crystallize in layer morphology. The pristine sample exhibits an exceedingly low lattice thermal conductivity of 0.6- 0.46 W·m -1 ·K -1 at 300-823 K, which derives from strong lattice anharmonicity, large Grüneisen parameters, and low phonon velocities induced by the complex crystal structure with heavy atom Bi and a large unit cell. Here, the Cl doping successfully enhances the carrier concentration in Rb 2 Bi 8 Se 13 with a negligible impact on the electronic band structure, displaying common doping behaviors. Se vacancy, on the contrary, leads to n-type doping and enhances the effective mass and power factors more significantly. Consequently, a maximum ZT of ~0.75 at 823 K for the 0.3% Se-vacancy-doped sample is obtained.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermoelectric performance in disordered Cu 2 ZnSnSe 4 nanostructures driven by ultra-low thermal conductivity

Here, high-energy reactive mechanical alloying (ball milling) was used to synthesize tetragonal and cubic polymorphs of Cu 2 ZnSnSe 4 . The ordered tetragonal (I-4) polymorph undergoes a phase transition above 400 K into a Cu-Zn disordered tetragonal (I-42 m) polymorph, while the cubic (F-43 m) polymorph with full cation disorder is stabilized at room temperature. Both polymorphs show ultra-low thermal conductivities, 0.42 W m -1 K -1 at 722 K and 0.21 W m -1 K -1 at 523 K for the disordered tetragonal and cubic phases respectively. The cubic polymorph has a higher zT in the low-temperature range, peaking at 0.26 (523 K), while the disordered tetragonal has a maximum zT of 0.46 at 712 K. The latter is the highest reported zT for stoichiometric Cu 2 ZnSnSe 4 , comparable to the best-performing doped materials in the literature. A combination of experimental results and ab-initio calculations point to a coupling between structural disorder and microstructure as the mechanism behind the reported performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Population balance modeling of polyurethane foam formation with pressure‐dependent growth kernel

Abstract Polyurethane foams are widely used materials often chosen for their useful characteristics such as low thermal conductivity, ease of application, and high strength‐to‐weight ratios. Computational models are needed to predict the dynamics of the flow and expansion, and the resulting material properties, to improve manufacturing processes. In this paper, a model for PMDI, a water‐blown polyurethane foam, is presented. By extending a kinetics‐based approach by adding bubble‐scale information via a population balance equation (PBE) using the quadrature method of moments, we can track bubble size distributions during foaming. We present results from a three‐dimensional computational fluid dynamics model using arbitrary Lagrangian–Eulerian interface tracking implemented in finite element software. The model compares favorably with experimental data, including dynamics, bubble distributions measured by both camera and diffusion wave spectroscopy, and post‐test bubble size from scanning electron microscopy and density measurements from x‐ray computed tomography.

Ortiz, Weston↗
DOE OSTI2022

Weak-Bonding Elements Lead to High Thermoelectric Performance in BaSnS 3 and SrSnS 3 : A First-Principles Study

SnS2, an earth-abundant and ecofriendly material, is limited as a thermoelectric material because of the high lattice thermal conductivity κ L and low carrier mobility μ. By introducing weak-bonding elements Ba or Sr into the SnS 2 framework, we discovered two SnS 2 -based materials BaSnS3 and SrSnS3 with the calculated low κL values of 0.15 and 0.17 W m -1 K -1 , respectively, along the a-axis. The low group velocity and high lattice anharmonicity originating from the weakened and distorted Sn–S bonding network are found in both systems. Moreover, the vibrations of Ba and Sr induce low-lying optical phonons, which strongly couple with the acoustic phonons and strengthen the phonon scattering rates. Compared to SnS 2 , both compounds present lower single-band effective masses, smaller deformation potential constants, and better band convergence, which enhance μ with an insignificantly reduced effective mass. By solving the linearized Boltzmann transport equation with a nonempirical carrier lifetime, we predict excellent ZT values of 2.89 and 2.77 along the a-axis at 900 K in BaSnS 3 and SrSnS 3 , respectively. Further phase diagram calculations of Ba 1–x Sr x SnS 3 solid solutions propose a new compound, Ba 0.5 Sr 0.5 SnS 3 , with an even higher ZT of 3.0. Our work analyzes explicitly how weak-bonding elements enhance μ and suppress κL simultaneously in SnS 2 -analogous systems with a series of compounds nominated as potential high-performance thermoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Corrosion evaluation of metal foams in eutectic molten salts for high temperature latent heat energy storage application

High-temperature Thermal Energy Storage (TES) has drawn great attention as a technology that can increase the role and profitability of micro nuclear reactors in the decentralized clean energy market. Various research needs have been proposed by Idaho National Laboratory (INL) in "the Integrated Energy Systems: 2020 Roadmap" with the goal of utilizing the high temperature of 550 degrees or more generated in the 4th generation reactor to industrial purposes from the standpoint of integrated energy systems [1]. With the recent development of the 4th generation nuclear power plant, including micro nuclear reactor, there is a great deal of interest in researching how to efficiently couple a heat source to an industrial process through thermal processing. Texas A&M University (TAMU) and INL are currently collaborating to develop a novel latent heat storage design called HITB (Heat pipe-Integrated Thermal Battery). As part of the small-scale experimental demonstration research for HITB, a study for storage medium selection was conducted at TAMU. Eutectic salts have attracted interest as high-temperature heat storage medium for HITB. Especially, chloride molten salts and fluoride molten salts are considered promising candidates due to their high melting temperature, thermal stability, and high latent heat of fusion. Since eutectic salts have poor thermal conductivity in general, it is critical to distribute materials with high thermal conductivity evenly to facilitate the charging and discharging of heat. In this study, metal foam was considered in the HITB system to overcome the poor heat transfer characteristics of eutectic salts. In order to improve heat transfer, it is necessary to study materials with high thermal conductivity, corrosion resistant to molten salts, such as fins, extended surfaces, particles, microcapsulation, or foam structure. Porous structure of copper or aluminum can increase heat transfer area, form a thermal transfer network, and increase the effective thermal conductivity of thermal storage medium [2]. Since the melting temperature is required to be at least 450? in the current HITB design, various eutectic salts are being considered. FLiNaK and FLiBe, which are famous for fluoride salts, are good candidates, but due to the sharp rise in the price of LiF recently, they are excluded for economic reasons to be applied to large-capacity thermal energy storage. On the other hand, chloride salts are very cheap and easy to obtain, have a high melting temperature, and have a high latent heat of fusion, so they are recently in the spotlight as a phase change material. However, because of the hygroscopic nature of chloride salts, HCl gas due to impurity is easy to be released and is particularly vulnerable to corrosion. Chloride eutectic salts have been tested and suggested for metal alloys that are particularly resistant to corrosion, such as SS304, SS316, Hastelloy, Inconel 625, Incoloy 800H, which has low thermal conductivity, and is very expensive [3-6]. Porous materials with high thermal conductivity such as copper and aluminum have been tested for stability in fluids such as paraffin or water as metal foam or metal fin structures, but high temperature corrosion tests were not performed on various eutectic salts yet. Therefore, this study investigated the high temperature corrosion characteristics of metal alloys, such as C10100 foam, C10100 plate, 6101 alloy foam, and SS316 plate, while immersed in the candidate eutectic salts. A total of 20 tests for SS316 coupons and 10 tests for C10100 coupons were performed to ensure the repeatability of the present measurements. Since it is difficult to completely remove the salt inside metal foam due to the complex inner structure of the metal foam, only the surface condition was observed with a microscopy and scanning electron microscopy (SEM) image, except for measuring the corrosion rate and average mass loss.

25 ENERGY STORAGE↗
DOE OSTI2022

Processing Compressed Expanded Natural Graphite for Phase Change Material Composites

Phase change materials (PCMs) are used in various thermal energy storage applications but are limited by their low thermal conductivity. One method to increase conductivity involves impregnating organic PCMs into highly porous conductive matrix materials. Of these materials, compressed expanded natural graphite (CENG) matrices have received the most attention. Despite this attention, the effect that CENG processing has on PCM saturation and overall matrix thermal conductivity has not been fully investigated. Therefore, the effect of the heat treatment process used to expand intercalated graphite flakes is evaluated here. Higher heat treatment temperatures yielded higher saturation rates and overall saturation at similar matrix porosities. For example, increasing temperature from 300 °C to 700 °C resulted in approximately 60%-70% increase in pore saturation after 100 minutes of soaking. The exposure time to heat treatment had less of an effect on PCM saturation. The exposure time had negligible effect above 30 min and above 500 °C heating temperatures. However, because the expanded graphite was found to oxidize around 700 °C, the use of longer exposure time in manufacturing applications can be beneficial if a shortened impregnation time is needed. Heat treatment conditions did not impact thermal conductivity. The composite latent heat of fusion was also reduced approximately proportionally to the PCM mass fraction. A local maximum in axial thermal conductivity was observed at around 83% porosity, which is similar to previous studies. The observed conductivity at this maximum was a factor of 81 times greater than the conductivity of the PCM.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultra-efficient polymer binder for silicon anode in high-capacity lithium-ion batteries

As a highly promising anode material for high-capacity lithium-ion batteries (LIBs), the low electronic conductivity and large volume variation of silicon (Si) make the slurry-coating Si based electrode requiring high content of “inert” materials and suffering rapid capacity fading. In this work, a polyimine, synthesized via one-step condensation reaction, has been demonstrated as an ultra-efficient polymer binder that can resolve the above issues. The polyimine binder containing Si electrode delivers superior electrochemical performance: a delithiation specific capacity of 804.4 mAh g –1 with capacity retention of 82.4% after 1000 cycles at the current density of 2 A g –1 . The high efficiency of polyimine binder for Si electrode has also been demonstrated with ultrahigh weight ratio of “active” material to “inert” material (R A/I ). The electrode with 95 wt% of Si (95Si/Polyimine, R A/I = 19) reveals a reversible delithiation capacity of 2114 mAh g –1 (capacity retention ~ 80.4%) over 200 cycles at the current density of 400 mA g –1 . Even at the high current density of 2 A g –1 , a delithiation capacity of 1087.8 mAh g –1 after 500 cycles can be obtained. Molecular simulations and atomic force microscopy (AFM) indentation are utilized to investigate the ultra-efficiency of polyimine binder. With simple manufacturing process and ultra-efficient binder performance, the designed polyimine binder will be definitely meaningful in achieving low-cost and high-capacity LIBs with prolonged cycle life.

25 ENERGY STORAGE↗
DOE OSTI2021

Critical roles of pores and moisture in sustainable nanocellulose-based super-thermal insulators

In a recent report in Matter, Bergström and co-workers describe a novel thermal transport behavior that subverts this assumption of porous materials. In their work, the authors describe a nanocellulose-based foam that features ultrahigh porosity (> 99.6%) and aligned µm-scale pores (10–100 µm) whose radial thermal conductivity (i.e., perpendicular to the pore alignment) is close to that of free air in the dry state. Furthermore, the radial thermal conductivity of the cellulose-based foam can be reduced to ~14 mW/(m·K) when the relative humidity is ~35%. Super-thermal insulators, which demonstrate a thermal conductivity below that of stationary air (~ 25 mW/(m·K), 20 ºC, 1.0 atm), are needed to minimize heat loss in various applications (e.g., buildings, thermal energy storage tanks, cold chain packaging, etc.) to mitigate the energy crisis and reduce carbon emissions. Introducing pores into a material is a facile and effective way to achieve low thermal conductivity as pores can suppress thermal transport through solids by reducing the cross-sectional area and increasing the tortuosity of the heat transfer pathway. In porous structures there are two kinds of pores: open and closed. While increased porosity can reduce heat conduction through solids with an open porous structure, the improved gas conduction creates a competing effect that simultaneously elevates the heat transfer. Therefore, the thermal conductivity of a material with µm-scale open pores is usually larger than that of stationary air. Reducing the pore size to less than the mean free path of air (~ 70 nm, 20 ºC, 1.0 atm) can effectively reduce gas conduction, enabling the material to achieve a thermal conductivity below that of stationary air. However, high cost of the nanosized raw materials and time-consuming fabrication processes limit the large-scale applications of nanoporous thermal insulators. Meanwhile, closed pores can block heat transport only through the continuous gas phase. As a result, the thermal conductivity of a closed porous structure can theoretically be much smaller than that of stationary air if the solid conduction can also be suppressed by (1) lowering the solid content of the material, (2) reducing the thermal conductivity of the building blocks of the material, and/or (3) increasing interfacial thermal resistance between neighboring building blocks. Most processes used to generate porous structures (e.g., supercritical drying, freeze drying) involve a solvent that escapes the material. Therefore, it is difficult to create pores and isolate them simultaneously, preventing the fabrication of super-thermal insulators with closed pores.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-Quality SnSe 2 Single Crystals: Electronic and Thermoelectric Properties

In this work, high-quality SnSe 2 single crystals were successfully synthesized using a temperature gradient method. N-type characteristics and strong anisotropic transport properties of SnSe 2 single crystals were exhibited between the ab plane and the c-axis. At 673 K, the power factor (PF) value along the ab plane is 3.43 μW cm -1 K -2 , while it is 0.92 μW cm -1 K -2 along the c-axis. The ratio between thermal conductivities along the ab plane (κ ab ) and c-axis (κ c ) is on the order of 7.6 at 300 K, while this value is about 5.6 at 673 K. The thermoelectric figure of merit (ZT) in the c-axis (0.15) is higher than that (0.1) along the ab plane, according to the ultralow out-of-plane thermal conductivity. The electronic band structure results, which were examined by angle-resolved photoemission spectroscopy (ARPES) predicted the potential of improving the thermoelectric performance of SnSe 2 single crystals by electron doping.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Structural and Morphological Characteristics of Rare Earth Element-based MAX Phase and MXene

There has been a tremendous effort for the synthesis of crystalline MAX phases—a family of transition metal carbides and nitrides with a chemical formula of Mn+1AXn, where M is an early transition metal, A belongs to groups XIII – XVI in the periodic table, X is either C or N, and n can be in between 1 and 3. Furthermore, these materials have shown thermal and electrical conductance and have low density and high stiffness which open broad aspects of practical applications. Recently double transition metal MAX phases (M’ 2/3 M’’ 1/3 ) 2 AX - out-of-plane ordered, labeled as o-MAX and in-plane ordered, labeled as i-MAX, were reported. However, there are few reports on the synthesis and characterization of i-MAX and the corresponding MXenes. In this work, we synthesized Molybdenum-based rare earth containing i-MAX phase using arc melt technique. We then removed “A” element of i-MAX phase by acid treatment and sonication which resulted in two-dimensional (2D) transition metal carbides called MXenes. These MXenes offer high conductivity, hydrophilicity, magnetism, good dispersion ability in solvents, mechanical stability, and structural diversity with at least 100 stoichiometric MXene compositions and are recognized as multifunctional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Using small angle x-ray scattering to examine the aggregation mechanism in silica nanoparticle-based ambigels for improved optical clarity

Silica-based aerogels are a promising low-cost solution for improving the insulation efficiency of single-pane windows and reducing the energy consumption required for space heating and cooling. Two key material properties required are high porosity and small pore sizes, which lead to low thermal conductivity and high optical transparency, respectively. However, porosity and pore size are generally directly linked, where high porosity materials also have large pore sizes. This is unfavorable as large pores scatter light, resulting in reduced transmittance in the visible regime. In this work, we utilized preformed silica colloids to explore methods for reducing pore size while maintaining high porosity. Further, the use of preformed colloids allows us to isolate the effect of solution conditions on porous gel network formation by eliminating simultaneous nanoparticle growth and aggregation found when using typical sol–gel molecular-based silica precursors. Specifically, we used in situ synchrotron-based small-angle x-ray scattering during gel formation to better understand how pH, concentration, and colloid size affect particle aggregation and pore structure. Ex situ characterization of dried gels demonstrates that peak pore widths can be reduced from 15 to 13 nm, accompanied by a narrowing of the overall pore size distribution, while maintaining porosities of 70%–80%. Optical transparency is found to increase with decreasing pore sizes while low thermal conductivities ranging from 95 +/− 13 mW/m K are maintained. Mechanical performance was found to depend primarily on effective density and did not show a significant dependence on solution conditions. Overall, our results provide insights into methods to preserve high porosity in nanoparticle-based aerogels while improving optical transparency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Poly(vinylferrocene) as an Ionomer and Sulfur-Confining Additive for Lithium–Sulfur Batteries

Lithium-sulfur (Li-S) batteries are promising owing to their high energy density, environmental benignity, and low cost. Most of the commonly used binders in Li-S battery cathodes are inert and have no significant effect on the challenges of sulfur as a cathode material, such as the polysulfide shuttle effect, low ionic/electronic conductivity, and a sluggish redox reaction. In this work, we demonstrate the use of poly(vinylferrocene) (PvFc) as a binder additive that can effectively increase the ionic conductivity of the cathode and act as a sulfide confining agent. Electrochemical tests performed with PvFc as part of the binder mixture used to cast the cathodes demonstrate an increase in rate capability and cycle life when compared to the baseline samples. Ionic conductivity measurements and X-ray photoelectron spectroscopy suggest that the π-cation molecular interaction between the cyclopentadienyl rings from ferrocene and Li + act like an ion couple with ferrocene acting as a static, covalently bound acceptor of Li + ions that enhances their mobility through the cathode. This coupled with the affinity between the ferrocenyl cations and the Li salt anions, which provides more distribution of counterions for Li + movement and improves accessibility to the cathode S reservoir, make PvFc a promising ionomer for Li-S batteries. In addition, the π-cation bonds between cyclopentadienyl and lithium polysulfides produce a sulfide confining effect that mitigates capacity fade through polysulfide dissolution. Furthermore, this work demonstrates an expansion in the utility of PvFc as a component in Li-ion batteries, which so far is mostly limited to use as an active material in organometallic batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Numerical Evaluation of Effective Thermal Conductivity of PCM with Metal Foam Incorporating Buoyancy Effects for Thermal Energy Storage

The thermal energy storage (TES) system has the capability to efficiently preserve thermal energy directly derived from the energy source, minimizing any conversion losses. Especially latent heat storage offers distinct advantages, including a substantial increase in energy storage density and minimization of temperature fluctuations within the plants. However, the phase change material (PCM) employed in latent heat storage has low thermal conductivity. Consequently, various studies are being conducted to enhance heat transfer. One approach to enhance heat transfer involves utilizing metal foam to maximize the heat transfer area. However, modeling metal foam with its intricate structure is a challenging task in numerical analysis. For this reason, ongoing research focuses on simplifying the modeling of metal foam. Nevertheless, fully encompassing all the characteristics of actual metal foam proves to be a challenging task for the simplified analytical model. The objective of this paper is to interpret the simple lattice metal foam analysis model from the perspective of behavior induced by buoyancy. When comparing the analysis results of solid PCM and liquid PCM with the same thermal conductivity under changes in porosity and gravity direction, we conducted an analysis to discern the trends in effective thermal conductivity that are overestimated due to convection. In the analysis, a constant heat flux of 10 kW and a constant surface boundary condition of 350 K were applied, and a sensitivity study regarding the mesh was conducted. The results indicate that, from the perspective of gravity in the simple lattice model, the solid analysis yields an effective thermal conductivity 29-47% higher compared to the liquid analysis. Additionally, as porosity increases, there is an observed increase of 24-33% in effective thermal conductivity.

25 ENERGY STORAGE↗
DOE OSTI2021

Anisotropic Structural Collapse of Mg 3 Sb 2 and Mg 3 Bi 2 at High Pressure

Alloys between Mg 3 Sb 2 and Mg 3 Bi 2 have recently been shown to be exceptional thermoelectric materials due in part to their anomalously low thermal conductivity. In the present study, in situ high-pressure synchrotron X-ray diffraction was used to investigate the structure and bonding in Mg 3 Sb 2 and Mg 3 Bi 2 at pressures up to 50 GPa. Our results confirm prior predictions of isotropic in-plane and out-of-plane compressibility but reveal large disparities between the bond strength of the two distinct Mg sites. Using single-crystal diffraction, we show that the octahedral Mg–Sb bonds are significantly more compressible than the tetrahedral Mg–Sb bonds in Mg 3 Sb 2 , which lends support to prior arguments that the weaker octahedral Mg bonds are responsible for the anomalous thermal properties of Mg 3 Sb 2 and Mg 3 Bi 2 . Further, we report the discovery of a displacive and reversible phase transition in both Mg 3 Sb 2 and Mg 3 Bi 2 above 7.8 and 4.0 GPa, respectively. Furthermore, the transition to the high-pressure structure involves a highly anisotropic volume collapse, in which the out-of-plane axis compresses significantly more than the in-plane axes. Single-crystal diffraction at high pressure was used to solve the monoclinic high-pressure structure ( C 2/ m ), which is a distorted variant of the ambient-pressure structure containing four unique Mg coordination environments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Surface Modification of Nickel-Rich Cathode Materials by Ionically Conductive Materials at Room Temperature

Nickel-rich cathode materials (LiNi x Mn y Co 1-x-y O 2 , NMC) are promising to push the limits of lithium-ion batteries to higher energy density. This approach is favored in practical applications including electric vehicles and aviation transportation. However, the instability of the NMC at charged state results in safety concerns and poor cycling stability. Surface coating is a practical and effective strategy to address this. Cubic Li7La3Zr2O12 (LLZO) is an ideal coating material regarding the low electron transfer rate and high Li+ conductivity. Thus, a LLZO coating layer can suppress the parasitic reactions in the electrode/electrolyte interface without deteriorating the lithium migration. However, high-temperature calcination seems to inevitably create the chemical couplings between NMC and LLZO, leading to the interdiffusion and degradation of NMC and LLZO crystal structures. This work presents a simple mechanochemical method to effectively coat LLZO on the NMC particle surface. Furthermore, the coated cathode demonstrates superior electrochemical performance compared with the pristine NMC cathode.

25 ENERGY STORAGE↗
DOE OSTI2026

Activation of Thermal Insulation and Contamination Prevention

The goals of this paper are to enhance the understanding of the potential activation and contamination hazards from the use of insulating materials in the Molten Chloride Reactor Experiment and to foster safer work environments through informed decision-making and strategic planning. It was written to resolve a gating comment from the core heating system preliminary design review. The largest dose expected from the considered insulation materials is about 0.1 mrem per year from Pyrogel. Although Cerablanket stood out among the insulation materials for encouraging ALARA practices, it has a higher thermal conductivity. At low power levels, focusing on reducing the generation of dust from ERD activities may be more effective for reducing the potential spread of contamination than changing the insulating material type. However, regardless of the material chosen, PPE and safety conscious procedural practices can help reduce the production and spread of activated dust––thus minimizing the radiological hazard to workers.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2024

Local Electric Field Effects on Water Dissociation in Bipolar Membranes Studied Using Core–Shell Catalysts

The local electric field strength is thought to affect the rate of water dissociation (WD) in bipolar membranes (BPMs) at the catalyst–nanoparticle surfaces. Here, we study core–shell nanoparticles, where the core is metallic, semiconducting, or insulating, to understand this effect. The nanoparticle cores were coated with a WD catalyst layer (TiO2 or HfO2) via atomic layer deposition (ALD), and the morphology was imaged with transmission electron microscopy. Irrespective of the core material, these core–shell catalysts displayed comparable WD overpotentials at optimal mass loading, despite the hypothesized differences in the electric field strength across the catalyst particle suggested by continuum electrostatic simulations. Substantial atomic interdiffusion between the core and shell was ruled out by X-ray absorption spectroscopy, X-ray photoelectron spectroscopy, and diffuse reflectance optical measurements. However, the optimal mass loading of catalyst was roughly 1 order of magnitude higher for the conductive and high dielectric core materials than for the low dielectric insulating cores. These findings are consistent with the hypothesis that electric field screening within the core material focuses the electric field drop between particles such that larger film thicknesses can be tolerated. Collectively, these data support the idea that it is the local electric field at the molecular level that controls proton-transfer rates and that the metal core/dielectric-shell constructs introduced here modulate that field. Further materials and synthetic design may enable optimization of the electric field strength across the proton-transfer trajectory at the material surface.

Sarma, Prasad V↗
DOE OSTI2023

Analysis of Deformation and Fracture Mechanisms in the Harvested Low-Dose Baffle Former Bolt via Advanced Mechanical Tests

This report details the production of tensile specimens from in-service irradiated baffle former bolts (BFBs) and presents the results of a pilot in-situ SEM/EBSD test conducted at Oak Ridge National Laboratory’s Low Activation Materials Development and Analysis (LAMDA) facility. The SEM/EDS results confirmed that the material is AISI 316L steel, not AISI 347, and that no Nb addition was detected in several analyzed locations. EBSD analysis of the microstructure revealed in-grain misorientation gradients indicative of cold work, likely caused by material processing, and no retained ferrite was identified. During straining, dislocation channel formation was the primary deformation mechanism, with twinning also observed in favorably oriented grains at local strains as small as ~1.5%. No strain-induced phase instability was observed, likely due to the fact that the Ni and Cr content reached the upper limits for the 316L steel specification. Multiple microfracture events were observed during the tensile test. Fine strain-induced pores formed at the channel-grain boundary intersection points, while coarser microcracks were associated with non-metallic inclusions. Data analysis is ongoing, and additional tests are planned in the near future to provide more statistics and details.

36 MATERIALS SCIENCE↗