SEARCH · Search NASA

Results for “low-frequency acoustics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

124 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Evaluation of discrete frequency sound in closed-test-section wind tunnels

The principal objective of this study is to assess the adequacy of linear acoustic theory with an impedance wall boundary condition for modeling the detailed sound field of an acoustic source in a duct. This study compares measurements and calculations of a simple acoustic source in a rectangular concrete duct lined with foam on the walls and anechoic end terminations. Measuring acoustic pressure for 12 wave numbers provides variation in frequency and absorption characteristics of the duct walls. The cases in this study contain low frequencies and low wall absorptions corresponding to measurements of low-frequency helicopter noise in a lined wind tunnel. This regime is particularly difficult to measure in wind tunnels due to high levels of the reverberant field relatively close to the source. Close to the source, where the interference of wall reflections is minimal, correlation is very good. Away from the source, correlation degrades, especially for the lower frequencies. Sensitivity studies show little effect on the predicted results for changes in impedance boundary condition values, source location, measurement location, temperature, and source model for variations spanning the expected measurement error.

Mosher, Marianne↗

NASA NTRS1992

Detection and characterization of fatigue cracks in thin metal plates by low frequency resonant model analysis

Low-frequency resonant model analysis, a technique for the detection and characterization of fatigue cracks in thin metal plates, which could be adapted to rapid scan or large area testing, is considered. Experimental data displaying a direct correlation between fatigue crack geometry and resonance frequency for the second vibrational plate mode are presented. FEM is used to calculate the mechanical behavior of the plates, and provides a comparison basis for the experimentally determined resonance frequency values. The waveform of the acoustic emission generated at the resonant frequency is examined; it provides the basis for a model of the interaction of fatigue crack faces during plate vibration.

Wincheski, B.↗

NASA NTRS1993

Dynamics of the solar chromosphere. I - Long-period network oscillations

We analyze differences in solar oscillations between the chromospheric network and internetwork regions from a 1 hr sequence of spectrograms of a quiet region near disk center. The spectrograms contain Ca II H, Ca I 422.7 nm, and various Fe I blends in the Ca II H wing. They permit vertical tracing of oscillations throughout the photosphere and into the low chromosphere. We find that the rms amplitude of Ca II H line center Doppler fluctuations is about 1.5 km/s for both network and internetwork, but that the character of the oscillations differs markedly in these two regions. Within internetwork areas the chromospheric velocity power spectrum is dominated by oscillations with frequencies at and above the acoustic cutoff frequency. They are well correlated with the oscillations in the underlying photosphere, but they are much reduced in the network. In contrast, the network Ca II H line center velocity and intensity power spectra are dominated by low-frequency oscillations with periods of 5-20 min. Their signature is much clearer in our Ca II H line center measurements than in previously used diagnostics which are contaminated by signals from deeper layers. We find that these long-period oscillations are not correlated with underlying photospheric disturbances, and we discuss their nature.

Lites, B. W.↗

NASA NTRS1995

Bearing defect signature analysis using advanced nonlinear signal analysis in a controlled environment

Utilizing high-frequency data from a highly instrumented rotor assembly, seeded bearing defect signatures are characterized using both conventional linear approaches, such as power spectral density analysis, and recently developed nonlinear techniques such as bicoherence analysis. Traditional low-frequency (less than 20 kHz) analysis and high-frequency envelope analysis of both accelerometer and acoustic emission data are used to recover characteristic bearing distress information buried deeply in acquired data. The successful coupling of newly developed nonlinear signal analysis with recovered wideband envelope data from accelerometers and acoustic emission sensors is the innovative focus of this research.

Zoladz, T.↗

NASA NTRS1995

Variability of accretion disks surrounding black holes: The role of inertial-acoustic mode instabilities

The global nonlinear time-dependent evolution of the inertial-acoustic mode instability in accretion disks surrounding black holes has been investigated. The viscous stress is assumed to be proportional to the gas pressure only, i.e., tau = alphap(sub g). It is found that an oscillatory nonsteady behavior exists in the inner regions of disks (r is less than 10r(sub g) where r(sub g) is the Schwarzschild radius) for sufficiently large alpha(greater than or approximately equal to 0.2) and for mass accretion rates less than about 0.3 times the Eddington value. The variations of the integrated bolometric luminosity from the disk, Delta L/L, are less than 3%. A power spectrum analysis of these variations reveals a power spectrum which can be fitted to a power-law function of the frequency Pis proportional to f(exp -gamma), with index gamma = 1.4-2.3 and a low-frequency feature at about 4 Hz in one case. In addition, a narrow peak centered at a frequency corresponding to the maximum epicyclic frequency of the disk at approximately 100-130 Hz and its first harmonic is also seen. The low-frequency modulations are remarkably similar to those observed in black hole candidate systems. The possible existence of a scattering corona in the inner region of the disk and/or other processes contributing to the power at high frequencies in the inner region of the accretion disk may make the detection of the high-frequency component difficult.

Chen, Xingming↗

NASA NTRS2000

Loads Combination Research at Marshall Space Flight Center

This is the result of a study conducted by the Structural Dynamics Division of the Marshall Space Flight Center concerning the combination of low- and high-frequency dynamic loads for spacecraft design. Low-frequency transient loads are combined with high frequency acoustically induced loads to arrive at a limit load, for design purposes. Different methods are used for combining the loads which can lead to considerable variation in limit loads, depending on which NASA Center did the calculation. This study investigates several different combination methods and compares the combination methods with Spacelab 1 flight data. In addition, the relative timing of low- and high-frequency loads is examined.

Ferebee, R.↗

NASA NTRS2000

Loads Combination Research at Marshall Space Flight Center

Ferebee, R.↗

NASA NTRS2001

Elimination of Intermediate-Frequency Combustion Instability in the Fastrac Engine Thrust Chamber

A series of tests were conducted to measure the combustion performance of the Fastrac engine thrust chamber. The thrust chamber exhibited benign, yet marginally unstable combustion. The marginally unstable combustion was characterized by chamber pressure oscillations with large amplitudes and a frequency that was too low to be identified as acoustic or high-frequency combustion instability and too high to be identified as chug or low-frequency combustion instability. The source of the buzz or intermediate-frequency combustion instability was traced to the fuel venturi whose violently noisy cavitation caused resonance in the feedline downstream. Combustion was stabilized by increasing the throat diameter of the fuel venturi such that the cavitation would occur more quietly.

Rocker, Marvin↗

NASA NTRS1992

AC Magnetic Field Frequency Dependence of Magnetoacoustic Emission

Our recent study has proved a strong correlation between the low-frequency AC applied magnetic field amplitude dependence of the asymmetry of the magnetoacoustic emission (MAE) burst and the strength of the domain wall-defect interaction in iron-base ferromagnets. For the present study the AC magnetic field frequency dependence of the asymmetry has been investigated in the range of 1 to 200 Hz. When represented by the third moment of the rectified acoustic emission pulses, the asymmetry becomes a bell-shaped function of frequency with its center located around 25 Hz. This experiment has been performed with low carbon, high yield stress steel specimens of three different levels of domain wall-defect interaction strength. The results show that the increase in the interaction strength causes a vertical down shift of the asymmetry in the entire frequency range investigated.

Namkung, M.↗

NASA NTRS2006

The Low-Noise Potential of Distributed Propulsion on a Catamaran Aircraft

The noise shielding potential of an inboard-wing catamaran aircraft when coupled with distributed propulsion is examined. Here, only low-frequency jet noise from mid-wing-mounted engines is considered. Because low frequencies are the most difficult to shield, these calculations put a lower bound on the potential shielding benefit. In this proof-of-concept study, simple physical models are used to describe the 3-D scattering of jet noise by conceptualized catamaran aircraft. The Fast Scattering Code is used to predict noise levels on and about the aircraft. Shielding results are presented for several catamaran type geometries and simple noise source configurations representative of distributed propulsion radiation. Computational analyses are presented that demonstrate the shielding benefits of distributed propulsion and of increasing the width of the inboard wing. Also, sample calculations using the FSC are presented that demonstrate additional noise reduction on the aircraft fuselage by the use of acoustic liners on the inboard wing trailing edge. A full conceptual aircraft design would have to be analyzed over a complete mission to more accurately quantify community noise levels and aircraft performance, but the present shielding calculations show that a large acoustic benefit could be achieved by combining distributed propulsion and liner technology with a twin-fuselage planform.

Posey, Joe W.↗

NASA NTRS2008

Separating Turbofan Engine Noise Sources Using Auto and Cross Spectra from Four Microphones

The study of core noise from turbofan engines has become more important as noise from other sources such as the fan and jet were reduced. A multiple-microphone and acoustic-source modeling method to separate correlated and uncorrelated sources is discussed. The auto- and cross spectra in the frequency range below 1000 Hz are fitted with a noise propagation model based on a source couplet consisting of a single incoherent monopole source with a single coherent monopole source or a source triplet consisting of a single incoherent monopole source with two coherent monopole point sources. Examples are presented using data from a Pratt& Whitney PW4098 turbofan engine. The method separates the low-frequency jet noise from the core noise at the nozzle exit. It is shown that at low power settings, the core noise is a major contributor to the noise. Even at higher power settings, it can be more important than jet noise. However, at low frequencies, uncorrelated broadband noise and jet noise become the important factors as the engine power setting is increased.

Miles, Jeffrey Hilton↗

NASA NTRS2014

Quantified Energy Dissipation Rates in the Terrestrial Bow Shock: Waves and Dissipation - 2

We present the first quantified measure of the energy dissipation rates, due to wave-particle interactions, in the transition region of the Earth's collision-less bow shock using data from the Time History of Events and Macro-Scale Interactions during Sub-Storms spacecraft. Our results show that wave-particle interactions can regulate the global structure and dominate the energy dissipation of collision-less shocks. In every bow shock crossing examined, we observed both low-frequency (less than 10 hertz) and high-frequency (approximately or greater than10 hertz) electromagnetic waves throughout the entire transition region and into the magnetosheath. The low-frequency waves were consistent with magnetosonic-whistler waves. The high-frequency waves were combinations of ion-acoustic waves, electron cyclotron drift instability driven waves, electrostatic solitary waves, and whistler mode waves. The high-frequency waves had the following: (1) peak amplitudes exceeding delta B approximately equal to 10 nanoteslas and delta E approximately equal to 300 millivolts per meter, though more typical values were delta B approximately equal to 0.1-1.0 nanoteslas and delta E approximately equal to 10-50 millivolts per meter (2) Poynting fluxes in excess of 2000 microWm(sup −2) (micro-waves per square meter) (typical values were approximately 1-10 microWm(sup −2) (micro-waves per square meter); (3) resistivities greater than 9000 omega meters; and (4) associated energy dissipation rates greater than 10 microWm(sup −3) (micro-waves per cubic meter). The dissipation rates due to wave-particle interactions exceeded rates necessary to explain the increase in entropy across the shock ramps for approximately 90 percent of the wave burst durations. For approximately 22 percent of these times, the wave-particle interactions needed to only be less than or equal to 0.1 percent efficient to balance the nonlinear wave steepening that produced the shock waves. These results show that wave-particle interactions have the capacity to regulate the global structure and dominate the energy dissipation of collision-less shocks.

Terrestrial bow 2↗

NASA NTRS2022

A Scaled Model Study of the PSL Facility for Alleviating Low-Frequency Howl

This report documents results from a scaled model experimental study of howl occurring in the Propulsion Systems Laboratory (PSL)during engine tests. The aim is to understand the sources of the howling noise and find possible remedies. It is shown that a jet discharged into the model of the duct gives rise to high levels of low frequency noise which occurs apparently due to excitation of duct acoustic modes randomly excited by the jet. A wire-mesh screen placed at the end of the duct model immediately downstream of the jet nozzle is shown to alleviate such noise significantly. Based on these results, an end treatment for the duct in the PSL facility is recommended.

engine test↗

NASA NTRS2022

Constraints on the Optical Depth to Reionization from Balloon-borne Cosmic Microwave Background Measurements

We assess the uncertainty with which a balloon-borne experiment, nominally called Tau Surveyor (τS), can measure the optical depth to reionization σ(τ) with given realistic constraints of instrument noise and foreground emissions. Using a τS fiducial design with six frequency bands between 150 and 380 GHz, with white and uniform map noise of 7 μK arcmin, achievable with a single midlatitude flight, and including Planck's 30 and 44 GHz data, we assess the error σ(τ) obtained with three foreground models and as a function of sky fraction f sky between 40% and 54%. We carry out the analysis using both parametric and blind foreground separation techniques. We compare the σ(τ) values to those obtained with low-frequency and high-frequency versions of the experiment called τS-lf and τS-hf, which have only four and up to eight frequency bands with narrower and wider frequency coverage, respectively. We find that with τS, the lowest constraint is σ(τ) = 0.0034, obtained for one of the foreground models with f sky = 54%. σ(τ) is larger, in some cases by more than a factor of 2, for smaller sky fractions, with τS-lf, or as a function of foreground model. The τS-hf configuration does not lead to significantly tighter constraints. The exclusion of the 30 and 44 GHz data, which give information about synchrotron emission, leads to significant τ misestimates. Decreasing noise by an ambitious factor of 10, while keeping f sky = 40%, gives σ(τ) = 0.0031. The combination of σ(τ) = 0.0034, baryon acoustic oscillation data from DESI, and future cosmic microwave background B-mode lensing data from the CMB-S3/CMB-S4 experiments could give σ(∑m v ) = 17 meV.

cosmic microwave background radiation↗

NASA NTRSDate not supplied

Aeroacoustic Computations of a Transonic Truss-Braced Wing Aircraft: Part 2 – Acoustic Signature and Noise Source Identification

High-fidelity, time-dependent simulations of a Boeing-designed, transonic, truss-braced-wing aircraft in cruise (clean) and landing configurations are leveraged to generate synthetic microphone-phased-array data for airframe noise prediction and assessment. These data sets are used to compute source localization (beamform) maps to determine the location and strength of primary and secondary airframe noise sources associated with this unique configuration. The synthetic phased-array implementation mimics the setup of a flight test. As this study is ongoing, preliminary integrated far-field spectra for the cruise configuration obtained at multiple spatial resolutions revealed significant tonal content that lacked convergence with increased resolution. The origin of several of these tones and their unusual convergence behavior was traced to the larger-than-normal trailing-edge thickness of the “as-tested” cruise model being simulated. Reducing the trailing-edge thickness to more realistic values eliminated most of the tones at low to moderate frequencies and improved spectrum convergence significantly. Applying lessons learned from the cruise simulations, several modifications to the geometry of the landing configuration were made and are described in this work. Results from permeable and solid Ffowcs-Williams and Hawkings surfaces at two different spatial resolutions (coarse and medium) are used to illustrate the major noise sources and determine convergence of the CLEAN integrated noise levels for the entire aircraft as well as major subcomponents. We demonstrate that the low-frequency content of the far-field spectrum is dominated by noise generated from the main landing gear, while the medium- and high-frequency content is dominated by the wing-leading-edge Krueger flaps. Since analysis of the acoustic maps for the landing configuration revealed several clusters of multiple sources along the wing leading edge, “high resolution” processing of the array data was used to distinguish more accurately the locations of sources.

Transonic Truss-Braced Wing↗

NASA NTRSDate not supplied

Fan Noise Predictions of the NASA Source Diagnostic Test using Unsteady Simulations with LAVA Part II - Tonal and Broadband Noise Assessment

The NASA Source Diagnostic Test (SDT) campaign experimental data is used for validation of a sliding mesh technique recently implemented within the Launch, Ascent, and Vehicle Aerodynamics computational framework for time-accurate simulation of rotating fans. The far-field acoustics are analyzed in this work, building upon the aerodynamic validation studies previously published in Part I. Two modeling approaches are explored: the unsteady Reynolds-averaged Navier Stokes (uRANS) with the negative Spalart-Allmaras (SA-neg) turbulence model closure, and a hybrid Reynolds-averaged Navier Stokes/large-eddy simulation (RANS/LES) paradigm employing a zonal detached-eddy simulation (ZDES) closure with enhanced shielding protection. Two convective flux scheme approaches with different dissipation properties are also explored with ZDES. The Ffowcs-Williams and Hawkings (FW-H) permeable surface approach is used for propagation of the near-field acoustics to the far-field microphone locations. This work analyzes the low-speed (approach) condition, characterized by a fan rotation speed of 7808 rotations-per-minute (RPM). Three different grid levels ranging between 200 million and 1.1 billion grid points are considered. Results show good prediction of the broadband noise levels at sideline angles ranging between 70° and 110°. The forward arc observers show an under-prediction of the overall sound pressure levels (OASPL) even at the fine grid level. A breakdown of the inlet and exhaust contributions reveals a steep drop-off in the broadband noise levels past a blade-passing frequency (BPF) of 1.5, potentially caused by a lack of resolved small-scale turbulent fluctuations in the interstage region. Past 110° the OASPL are over-predicted by up to 10 dB due to an over-prediction of the low-frequency broadband noise levels in the aft arc. The detuning of BPF2 caused by small deviations in the blade stagger angle around the wheel is captured, and a corresponding decrease in the sound power level for this cut-on tone is observed.

AATT↗