Search NASA⌕ Search

SEARCH · Search NASA

Results for “magnetron sputtering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effect of substrate temperature on sputter-deposited boron carbide films

Sputter deposition of B4C films with tailored physical properties remains a challenge. Here, we systematically study how substrate temperature influences the properties of B4C films deposited by direct current magnetron sputtering onto planar substrates held at temperatures in the range of 100-510°C. Results show that all films are amorphous stoichiometric B4C, with low O content of ~1 at. %. Films deposited onto substrates at 100°C exhibit high compressive residual stress and decreased mechanical properties. Therefore, for elevated substrate temperatures in the range of 180-510°C, film mass density, surface roughness, Young’s modulus, and hardness are weakly dependent on substrate temperature. However, in this temperature range, an increase in substrate temperature leads to larger residual compressive stress accompanied by a corresponding reduction in the concentration of nanoscale inhomogeneities. At least for the landing atom ballistics conditions studied here, a substrate temperature range of ~185-250°C is optimum for growing films with near-zero intrinsic residual stress. The overall weak substrate temperature dependence of film properties revealed in this work is favorable for the development of a robust deposition process, particularly for the case of deposition onto non-planar substrates where temperature control is often challenging.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Sputter deposition of high electrical resistivity Au-Ta alloy coatings on rotating substrates

Sputter deposition of gold-tantalum alloy coatings is a key process for manufacturing hohlraums for magnetically-assisted inertial confinement fusion implosions. In this report we describe direct current magnetron sputter deposition of ~ 10 - μ~ 10 - μm-thick films of Au-80 at.% Ta onto rotating sphero-cylindrical hohlraum and planar Si witness substrates. Emphasis is given to how film microstructure and properties are affected by main deposition parameters, including argon working gas pressure, substrate bias, and the source composition (a single alloyed target compared to co-sputtering from two elemental targets). Experimental findings are correlated with distributions of landing energies and incident angles of depositing species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Deposition conditions characterized by low energetics of depositing species favor the formation of a β-Ta-like phase. Implications of these results to hohlraum fabrication are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-Rate Sputter Deposition of Ultrathick Boron Carbide Coatings on Rolling Spherical Substrates

Amorphous boron carbide (B 4 C) is a promising next-generation ablator material for inertial confinement fusion. However, the deposition of ultrathick B4C coatings with submicron-scale density uniformity on spherical substrates, as required for ablator shell fabrication, remains challenging. Here, in this study, we use direct current magnetron sputtering to deposit B 4 C onto 2-mm-diameter Si spheres rolling in a dish-shaped substrate holder. High deposition rates of ∼3 μm/h are achieved. Ultrathick films have a columnar microstructure, with the column width determined by the density of nodular defects. Nodular defect nucleation is dominated by the pickup of particulates from the holder during substrate rolling. We demonstrate the fabrication of a hollow B 4 C spherical shell with a wall thickness of 80 μm. Also demonstrated is the laser machining of holes in the B 4 C coating, which is necessary for both the chemical removal of the Si template and the attachment of a fusion fuel fill tube.

Inertial confinement fusion targets↗
DOE OSTI2022

Combinatorial sputter deposition of ultrathick Au-Bi alloy films

We report gold-bismuth alloys are of interest as catalysts and catalytic sensing systems, electrochemical sensors, superconductors, and hohlraums for magnetically assisted inertial confinement fusion implosions. Radiation-hydrodynamics simulations with the Lasnex code of laser-driven hohlraums predict higher x-ray drive from Au-Bi alloys compared with cases of Au-Ta or pure Au and Bi hohlraums. Here, we use direct current magnetron sputtering in Ar gas, with co-sputtering from two elemental targets, to deposit Au-Bi alloys with Bi content of 9–77 at.% and thicknesses up to ~20 µm. Films are characterized by a combination of x-ray diffraction, Rutherford backscattering, scanning electron microscopy, substrate-curvature-based residual stress, and electronic transport measurements. Experiments are complemented by Monte Carlo simulations of ballistic sputtering and gas phase transport of depositing species and Ar gas atoms. Results show that all films are polycrystalline, with three distinct compositional regimes dominated by Au, Au 2 Bi, and Bi crystallographic phases. A metallic behavior of the temperature dependence of electrical resistivity is observed for all the films. Films with Bi content above ~30 at.% exhibit porosity, which is tolerable to hohlraum x-ray drive based on Lasnex simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Experimental and theoretical study of hole scattering in RF sputtered p-type Cu 2 O thin films

One of the key materials of interest for p-type oxide semiconductor thin film electronics is cuprous oxide (Cu 2 O), due to its relatively high hole mobility. Here, in this work, we use experiments, analytical models, and density functional theory calculations to study the scattering mechanisms that determine Hall mobility in two Cu 2 O samples. First, we examine a polycrystalline Cu 2 O thin film deposited by RF magnetron sputtering, and second, a single-crystalline Cu2O bulk substrate. Temperature-dependent Hall measurements indicate that neutral impurity and grain boundary scattering are dominant for the polycrystalline Cu 2 O thin film, while phonon scattering is dominant for single-crystalline Cu 2 O. Our first-principles calculations show that the room-temperature intrinsic hole mobility of Cu 2 O is 106 cm 2 V –1 s –1 , indicating the great promise of the material for p-type electronic devices. This intrinsic mobility is limited by phonon scattering, with the most dominant scattering modes having phonon energies of 88.4 and 17.1 meV. These results indicate that the key pathways to increase the hole mobility in Cu 2 O thin films are by reducing the impurity concentration and by increasing grain size. Our work thus sets the stage for the future development of high performance Cu 2 O-based p-type thin film transistors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Low-loss Si-based Dielectrics for High Frequency Components of Superconducting Detectors

Silicon-based dielectric is crucial for many superconducting devices, including high-frequency transmission lines, filters, and resonators. Defects and contaminants in the amorphous dielectric and at the interfaces between the dielectric and metal layers can cause microwave losses and degrade device performance. Optimization of the dielectric fabrication, device structure, and surface morphology can help mitigate this problem. We present the fabrication of silicon oxide and nitride thin film dielectrics. We then characterized them using Scanning Electron Microscopy, Atomic Force Microscopy, and spectrophotometry techniques. The samples were synthesized using various deposition methods, including Plasma-Enhanced Chemical Vapor Deposition and magnetron sputtering. The film's morphology and structure were modified by adjusting the deposition pressure and gas flow. The resulting films were used in superconducting resonant systems consisting of planar inductors and capacitors. Measurements of the resonator properties, including their quality factor, were performed.

low-loss dielectrics↗
DOE OSTI2024

Effect of boron concentration on local structure and spontaneous polarization in AlBN thin films

The discovery of ferroelectricity in polar wurtzite-based ternary materials, such as Al 1–x B x N, has attracted attention due to their compatibility with complementary metal–oxide–semiconductor processes and potential use in integrated non-volatile memory devices. However, the origin of ferroelectricity and the fundamental control of the polarization switching in these materials are still under intensive investigation but appear to be related to local disorder induced from the alloying. In this work, we report the effect of boron alloying on the local structure of Al 1–x B x N films deposited by magnetron sputtering. Our results reveal a diminished crystalline order as a function of boron concentration, accompanied by a reduction in the spontaneous polarization. The film disorder is primarily associated with the dissimilar bond lengths between Al–N and B–N and the formation of threading dislocations induced by B incorporation in the structure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Deposition and characterization of α-Fe 2 O 3 /Pd thin films for neutron reflectometry studies

Here, we report deposition of hematite/Pd thin films on silicon wafers via radio frequency (RF) magnetron sputtering and subsequent characterization for future in situ neutron reflectometry studies. Following deposition, the hematite/Pd thin films were characterized as prepared and after annealing in air for 2h at 400, 500, and 600 °C, respectively. Raman spectroscopy, grazing incidence x-ray diffraction, and neutron reflectometry (NR) were used to characterize the structure and chemical compositions of the thin films. The results indicate that pure α-Fe 2 O 3 (hematite) films were produced, free from other iron oxide phases and impurities. NR data reveal that one intermediate layer between the Pd layer and the hematite layer was formed during sputtering deposition processes. The fitted scattering length density (SLD) of the as-deposited hematite layer is 70% of the theoretical SLD value, indicating that the grains are loosely packed in the RF-deposited hematite films. After annealing at elevated temperatures, the hematite films show increased SLD values but remain comparable to that of preannealed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Instrument for in situ hard x-ray nanobeam characterization during epitaxial crystallization and materials transformations

Solid-phase epitaxy (SPE) and other three-dimensional epitaxial crystallization processes pose challenging structural and chemical characterization problems. The concentration of defects, the spatial distribution of elastic strain, and the chemical state of ions each vary with nanoscale characteristic length scales and depend sensitively on the gas environment and elastic boundary conditions during growth. The lateral or three-dimensional propagation of crystalline interfaces in SPE has nanoscale or submicrometer characteristic distances during typical crystallization times. Here, an in situ synchrotron hard x-ray instrument allows these features to be studied during deposition and crystallization using diffraction, resonant scattering, nanobeam and coherent diffraction imaging, and reflectivity. The instrument incorporates a compact deposition system allowing the use of short-working-distance x-ray focusing optics. Layers are deposited using radio-frequency magnetron sputtering and evaporation sources. The deposition system provides control of the gas atmosphere and sample temperature. The sample is positioned using a stable mechanical design to minimize vibration and drift and employs precise translation stages to enable nanobeam experiments. Results of in situ x-ray characterization of the amorphous thin film deposition process for a SrTiO 3 /BaTiO 3 multilayer illustrate implementation of this instrument.

47 OTHER INSTRUMENTATION↗
NASA NTRSDate not supplied

Characterization of NiC Multilayer Coating Stress for X-Ray Optic Applications

NiC multilayers have been identified as a promising coating design for hard X-ray astrophysical imaging applications enabling bandpass extension beyond the Pt K-edge of approximately 78 keV. However, these coatings are difficult to deposit with low interfacial roughness below a bilayer thickness of about 35 ˚A. Utilizing a DC magnetron sputtering system, NiC multilayer of varying d-spacings are deposited on flat Si wafers and characterized using 8.048 keV X-ray reflectometry measurements. The residual coating stress is also measured using interferometry. We investigate how deposition parameters affect both the coating quality (i.e. surface/interfacial roughness, density, etc.) and the residual coating stress. From these experimental results conducted on flat substrates, we employ FEM and ray trace simulations to determine how NiC multilayer stress could impact the figure, and therefore performance, of full shell X-ray optics.

mulitlayer↗
DOE OSTI2025

Solid solutions limited by grain-boundary solute clustering in ultrafine-grained alloys

Immiscible Ag-Cu alloys exhibit complex behavior due to varying Cu solid solubilities reported under equilibrium and metastable conditions. In ultrafine-grained alloys, these limits are further complicated by a high fraction of grain boundaries, where solute atoms tend to segregate and, in some cases, form clusters. Here, this study investigates the influence of Cu solute segregation and clustering on solid-solution limits in ultrafine-grained Ag-Cu alloys synthesized by magnetron sputtering with varying Cu content. X-ray diffraction peak shifts reveal a solid-solution concentration plateau for Cu contents from 4.9 to 11.7 at %, in contrast to the peak shifts predicted by density-functional theory for Ag-Cu alloys. Scanning transmission electron microscopy further reveals limited solid solubility and the formation of numerous Cu-rich clusters at grain boundaries. Atomistic simulations demonstrate that such limited solubility does not arise from grain boundary segregation alone, but only when strong solute-solute interactions promote the formation of grain-boundary Cu solute clusters.

Density-functional theory↗
DOE OSTI2020

A pathway to synthesizing single-crystal Fe and FeCr films

Nuclear reactor environments provide a unique scientific and engineering challenge wherein materials must tolerate prolonged exposure to concurrent irradiation, elevated temperatures, and corrosive media. However, uncontrolled variability in material composition and structure often prohibits truly single-variable experiments that can reveal basic aspects of environmental damage. Here, Magnetron sputtering is used to provide a more controlled model system for these fundamental studies, yielding reproducible single-crystal Fe and FeCr thin films containing 8 and 18 at.% Cr. Electron microscopy is used to determine the systematic correlations between growth conditions and the resulting film microstructure and surface morphology. It is found that the substrate temperature and applied radio frequency (RF) bias can be tuned to obtain consistent homogeneous and single crystal films with a minimal amount of Ar impurities from the RF bias process. Epitaxial, single-crystal Fe films are obtained on MgO substrates at 500 °C with 10 Watt (W) RF bias deposition. However, when Cr is alloyed with Fe, higher substrate temperatures (600 °C) and applied RF biases (15 W) are required to achieve a similar epitaxial single-crystal FeCr film. Accelerated molecular dynamics simulations reveal that Cr impedes surface transport, explaining the need for higher temperature and bias during the growth of the Cr-bearing films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ultrathin Ruthenium Films on Graphene Buffered SiO 2 via Quasi Van der Waals Epitaxy

In this study, we demonstrate a quasi van der Waals epitaxy approach to prepare single crystalline Ru ultrathin film on large scale, monolayer graphene. Physical and epitaxial properties of bulk, near surface and surface of ultrathin Ru films were comprehensively studied using various structural, morphological, compositional, and electrical characterization techniques. Here, we confirm that Ru can epitaxially grow on single, monolayer graphene using magnetron sputtering at elevated temperature of 600 °C. The epitaxial Ru films with film thickness ranging from 94.2 nm down to 3.9 nm show the (0001) out-of-plane orientation. The epitaxial relationships between Ru and graphene are out-of-plane Ru(0001) || graphene(0001) and in-plane Ru[$11\bar20$] || graphene[$11\bar20$]. All the Ru films show smooth surfaces with root-mean-square roughness less than 0.8 nm and have negligible oxide layer on the surfaces. The Ru films on graphene demonstrate significantly reduced electrical resistivity comparing to their counterpart grown on bare SiO 2 , which show polycrystalline nature. For 7.1 to 3.9 nm film thicknesses, the resistivity of Ru on graphene shows 38 to 45% resistivity decrease from that of Ru film on bare SiO 2 without graphene. Our observations suggest the existence of the above-classical van der Waals interaction between Ru and graphene. On the other hand, graphene is capable of effectively blocking the inter-diffusion/interaction between Ru and SiO 2 during a 1000 °C annealing process.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Perspectives on novel refractory amorphous high-entropy alloys in extreme environments

Two new refractory amorphous high-entropy alloys (RAHEAs) within the W–Ta–Cr–V and W–Ta–Cr–V–Hf systems were herein synthesized using magnetron-sputtering and tested under high-temperature annealing and displacing irradiation using in situ Transmission Electron Microscopy. While the 14W-41Ta-26Cr-19V in at.% RAHEA (defined as WTaCrV RAHEA) was found to be unstable under such tests, additions of Hf in this system composing a new quinary 24W-40Ta-18Cr-5V-13Hf in at.% RAHEA (defined as WTaCrVHf RAHEA) was found to be a route to achieve stability both under annealing and irradiation. A new effect of nanoprecipitate reassembling observed to take place within the WTaCrVHf RAHEA under irradiation indicates that a duplex microstructure composed of an amorphous matrix with crystalline nanometer-sized precipitates enhances the radiation response of the system. Further, it is demonstrated that tunable chemical complexity arises as a new alloy design strategy to foster the use of novel RAHEAs within extreme environments. New perspectives for the alloy design and application of chemically-complex amorphous metallic alloys in extreme environments are presented with focus on their thermodynamic phase stability when subjected to high-temperature annealing and displacing irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ferroelectrics everywhere: Ferroelectricity in magnesium substituted zinc oxide thin films

We demonstrate ferroelectricity in Mg-substituted ZnO thin films with the wurtzite structure. Zn 1–x Mg x O films are grown by dual-cathode reactive magnetron sputtering on (111)-Pt // (0001)-Al 2 O 3 substrates at temperatures ranging from 26 to 200 °C for compositions spanning from x = 0 to x = 0.37. X-ray diffraction indicates a decrease in the c-lattice parameter and an increase in the a-lattice parameter with increasing Mg content, resulting in a nearly constant c/a axial ratio of 1.595 over this composition range. Transmission electron microscopy studies show abrupt interfaces between Zn 1–x Mg x O films and the Pt electrode. When prepared at pO 2 = 0.025, film surfaces are populated by abnormally oriented grains as measured by atomic force microscopy for Mg concentrations >29%. Raising pO 2 to 0.25 eliminates the misoriented grains. Optical measurements show increasing bandgap values with increasing Mg content. When prepared on a 200 °C substrate, films display ferroelectric switching with remanent polarizations exceeding 100 μC cm –2 and coercive fields below 3 MVcm –1 when the Mg content is between ~30% and ~7%. Substrate temperature can be lowered to ambient conditions, and when doing so, capacitor stacks show only minor sacrifices to crystal orientation and nearly identical remanent polarization values; however, coercive fields drop below 2 MV/cm. Using ambient temperature deposition, we demonstrate ferroelectric capacitor stacks integrated directly with polymer substrate surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Growth and structure of alpha-Ta films for quantum circuit integration

Tantalum films incorporated into superconducting circuits have exhibited low surface losses, resulting in long-lived qubit states. The remaining loss pathways originate in microscopic defects that manifest as two level systems (TLSs) at low temperatures. These defects limit performance, so careful attention to tantalum film structures is critical for optimal use in quantum devices. In this work, we investigate the growth of tantalum using magnetron sputtering on sapphire, Si, and photoresist substrates. In the case of sapphire, we present procedures for the growth of fully-oriented films with α-Ta [1 1 1]//Al2O3 [0 0 0 1] and α-Ta [1 −1 0]//Al2O3 [1 0 −1 0] orientational relationships and having residual resistivity ratio (RRR) ∼ 60 for 220 nm thick films. On Si, we find a complex grain texturing with Ta [1 1 0] normal to the substrate and RRR ∼ 30. We further demonstrate airbridge fabrication using Nb to nucleate α-Ta on photoresist surfaces. For the films on sapphire, resonators show TLS-limited quality factors of 1.3 ± 0.3 × 106 at 10 mK (for a waveguide gap and conductor width of 3 and 6 μm, respectively). Structural characterization using scanning electron microscopy, x-ray diffraction, low temperature transport, secondary ion mass spectrometry, and transmission electron microscopy reveal the dependence of residual impurities and screw dislocation density on processing conditions. The results provide practical insights into the fabrication of advanced superconducting devices including qubit arrays and guide future works on crystallographically deterministic qubit fabrication.

42 ENGINEERING↗
DOE OSTI2025

Topochemical Synthesis and Electronic Structure of High-Crystallinity Infinite-Layer Nickelates on an Orthorhombic Substrate

Superconductivity in infinite-layer nickelates has stirred much research interest, to which questions regarding the nature of superconductivity remain elusive. A critical leap forward to address these intricate questions is through the growth of high-crystallinity infinite-layer nickelates, including the “parent” phase. Here, we report the synthesis of a high-quality thin-film nickelate, NdNiO 2 . This is achieved through the growth of a perovskite precursor phase (NdNiO 3 ) of superior crystallinity on the NdGaO 3 substrate by off-axis RF magnetron sputtering and a low-temperature topochemical reduction using NaH. We observe a nonlinear Hall effect at low temperatures in this “non-doped” phase. We further study the electronic properties using advanced X-ray scattering and first-principles calculations. We observe spectroscopic indications of the enhanced two-dimensionality and a reduced hybridization of Nd 5d and Ni 3d orbitals. These findings unlock new pathways for preparing high-quality infinite-layer nickelates and provide new insights into the intrinsic features of these compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Ferroelectricity of wurtzite Al 1−x Hf x N heterovalent alloys

Thin films of aluminum hafnium nitride (Al1−xHfxN) were synthesized via reactive magnetron sputtering for Hf contents up to x = 0.13. X-ray diffraction showed a single c-axis oriented wurtzite phase for all films. Hard x-ray photoelectron spectroscopy demonstrated homogeneous Al:Hf distribution through the thin films and confirmed their insulating character. A collection of complementary tests showed unambiguous polarization inversion, and thus ferroelectricity in multiple samples. Current density vs electric field hysteresis measurements showed distinct ferroelectric switching current peaks, the piezoelectric coefficient d 33,f,meas measured using a double beam laser interferometer (DBLI) showed a reversal in sign with similar magnitude, and anisotropic wet etching confirmed field-induced polarization inversion. This demonstrates the possibility of using tetravalent–and not just trivalent–alloying elements to enable ferroelectricity in AlN-based thin films, highlighting the compositional flexibility of ferroelectricity in wurtzites and greatly expanding the chemistries that can be considered for future devices.

36 MATERIALS SCIENCE↗