Search NASA⌕ Search

SEARCH · Search NASA

Results for “material flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Mechanical joining with self piercing solid-rivets at elevated tool velocities

In the present paper the influence of a higher setting velocity in the joining process of self piercing solid-rivets is shown. In the conventional process tool velocities well below 1 m/s are common. The present research results show the potential of increasing them in the range of about 5 m/s. The results are especially relevant for joining high-strength steels. These steel sheets often cause problems in the process of riveting mixed materials, e. g. aluminium-steel compound. The high strength of the steel sometimes leads to undesirable material flow in the joining process or unwanted burr development. These effects, which are described in detail in the article, can be reduced significantly for the investigated cases by the use of higher tool velocities. Using a high speed camera and a load cell, a test setup based on a drop tower was realized. It was used to time the force signals and the motion profile of the high speed riveting process. The results of the force analysis show an oscillating force progression. Within a numerical research the principal effects influencing the results of the riveting process can be shown. It was found that the pulse-like force transmission between riveting machine and punch, results in various vibrations especially of long and thin tool parts. Hence the rivet penetrates the sheet metal with non-uniform velocities. As a result the early indentation of die into the lower sheet metal at the beginning of the process is reduced, so that the final process step provides a sufficient material flow into the circular rivet groove. A strain-rate dependent process model with elastic tool properties and consideration of inertia effects is presented.

36 MATERIALS SCIENCE↗

Determination of elemental constituents in different matrix materials and flow injection studies by the electrolyte cathode glow discharge technique with a new design

An open-to-air type electrolyte cathode discharge (ELCAD) has been developed with a new design. The present configuration leads to a stable plasma even at low flow rates (0.96 mL/min). Plasma fluctuations arising from the variations in the gap between solid anode and liquid cathode were eliminated by providing a V-groove to the liquid glass-capillary. Cathode (ground) connection is given to the solution at the V-groove itself. Interfaced to atomic emission spectrometry (AES), its analytical performance is evaluated. The optimized molarity of the solution is 0.2 M. The analytical response curves for Ca, Cu, Cd, Pb, Hg, Fe, and Zn demonstrated good linearity. The limit of detections of Ca, Cu, Cd, Pb, Hg, Fe, and Zn are determined to be 17, 11, 5, 45, 15, 28, and 3 ng mL{sup -1}. At an integration time of 0.3 s, the relative standard deviation (RSD) values of the acid blank solutions are found to be less than 10% for the elements Ca, Cu, Cd, Hg, Fe, and Zn and 18% for Pb. The method is applied for the determination of the elemental constituents in different matrix materials such as tuna fish (IAEA-350), oyster tissue (NIST SRM 1566a), and coal fly ash (CFA SRM 1633b). The obtained results are in good agreement with the certified values. The accuracy is found to be between 7% and 0.6% for major to trace levels of constituent elements and the precision between 11% and 0.6%. For the injection of 100 {mu} L of 200 ng mL{sup -1} mercury solution at the flow rate of 0.8 mL/min, the flow injection studies resulted in the relative standard deviation (RSD) of 8%, concentration detection limit of 10 ng/mL, and mass detection limit of 1 ng for mercury.

01 COAL, LIGNITE, AND PEAT↗

Shear Assisted Processing and Extrusion (ShAPE™) of AZ91E Flake: A Study of Tooling Features and Processing Effects

Charges of melt-spun AZ91E flake were indirectly extruded into tubes using Shear Assisted Processing and Extrusion (ShAPE™). The effect of instrument parameters and tool features on densification and microstructural evolution was studied. At a constant extrusion ratio, the tool rotational velocity varied from 75 to 300 rpm and was demonstrated to reduce the forge force by a factor of four. Modification of the extrusion die face with successively more aggressive scrolled features was found to enhance material flow into the extrusion orifice which led to a 30% reduction in spindle torque. Microstructure, texture and hardness are reported for the range of rpm and scroll geometries investigated. It was observed that the ShAPE™ process is able to retain the average grain size of the as-spun flake (2.5-4 μm) while simultaneously imparting strong textural alignment in the resultant tube.

36 MATERIALS SCIENCE↗

Elucidation of microstructural evolution of beta-type titanium alloy joint during friction stir welding using liquid CO2 cooling

Highlights: • Microstructural evolution during FSW was elucidated along real material flow line. • Stirring and cooling stages of FSW can be investigated separately using CO{sub 2} cooling. • In stirring stage, discontinuous dynamic recrystallization predominantly occurred. • In cooling stage, static recovery and grain growth mainly occurred. - Abstract: Normal friction stir welding (FSW) and liquid CO{sub 2} cooling FSW were conducted on the β-type Ti-15V-3Cr-3Al-3Sn (Ti-15-3, mass%) alloy plates under a processing condition. Since liquid CO{sub 2} cooling with high cooling efficiency can freeze the microstructure formed during the high-temperature stirring stage of FSW, it is possible to separately elucidate the microstructural evolution of the Ti-15-3 alloy during the high-temperature stirring stage and the post-stirring cooling stage in FSW. The deformation temperature during the normal and the CO{sub 2} cooling FSW was similar in the top and the bottom of stir zone, which is considered to be owing to that the top and bottom are located adjacent to the heat sources, i.e., the shoulder and probe surfaces. In the high-temperature stirring stage of FSW, discontinuous dynamic recrystallization predominantly occurred, and a simple shear texture generated in an early stage of the material flow around the tool, then the microstructure started to evolve steadily after a steady-state dynamic recrystallization. In the post-stirring cooling stage of FSW, static recovery and grain growth were found to mainly occur within the stir zone.

36 MATERIALS SCIENCE↗

Design of a Biomass Scale Cubical Triaxial Tester

The bioenergy industry is dependent on predictable and reliable feedstock handling equipment. High profile failures in the industry demonstrate the need for better modeling tools for feedstock handling, specifically tools which can model the bulk flow of biomass feedstock materials in handling equipment such as hoppers or screw conveyors. Measurement of bulk material flow characteristics is a critical component to inform modeling tools. Following examples in the soils and pharmaceuticals industries, a Cubical Triaxial Tester (CTT) was selected as a critical component to study relationships between applied stress on a bulk sample and the resulting strain on the bulk material. In cooperation with The Pennsylvania State University, Forest Concepts designed a CTT specifically to measure bulk biomass flowability characteristics. Several mechanical design constraints were identified to ensure proper scaling and repeatability. Major design constraints included sample chamber size versus particle length, volumetric strain sensing accuracy, independent axial pressure control, and sample chamber handling. This report explains how major design constraints were determined.

09 BIOMASS FUELS↗

Material and Energy Flows in the Production of Cathode and Anode Materials for Lithium Ion Batteries

The Greenhouse gases, Regulated Emissions and Energy use in Transportation (GREET) model has been expanded to include four new cathode materials that can be used in the analysis of battery-powered vehicles: lithium nickel cobalt manganese oxide (LiNi 0.4 Co 0.2 Mn 0.4 O 2 [NMC]), lithium iron phosphate (LiFePO 4 [LFP]), lithium cobalt oxide (LiCoO 2 [LCO]), and an advanced lithium cathode (0.5Li 2 MnO 3 ∙0.5LiNi 0.44 Co 0.25 Mn 0.31 O 2 [LMR-NMC]). In GREET, these cathode materials are incorporated into batteries with graphite anodes. In the case of the LMR-NMC cathode, the anode is either graphite or a graphite-silicon blend. This report documents the material and energy flows of producing each of these cathode and anode materials from raw material extraction through the preparation stage. For some cathode materials, we considered solid state and hydrothermal preparation methods. Further, we used Argonne National Laboratory’s Battery Performance and Cost (BatPaC) model to determine battery composition (e.g., masses of cathode, anode, electrolyte, housing materials) when different cathode materials were used in the battery. Our analysis concluded that cobalt- and nickel-containing compounds are the most energy intensive to produce.

25 ENERGY STORAGE↗

Material and Energy Flows in the Production of Cathode and Anode Materials for Lithium Ion Batteries

The Greenhouse gases, Regulated Emissions and Energy use in Transportation (GREET) model has been expanded to include four new cathode materials that can be used in the analysis of battery-powered vehicles: lithium nickel cobalt manganese oxide (LiNi 0.4 Co 0.2 Mn 0.4 O 2 [NMC]), lithium iron phosphate (LiFePO 4 [LFP]), lithium cobalt oxide (LiCoO 2 [LCO]), and an advanced lithium cathode (0.5Li 2 MnO 3 ∙0.5LiNi 0.44 Co 0.25 Mn 0.31 O 2 [LMR-NMC]). In GREET, these cathode materials are incorporated into batteries with graphite anodes. In the case of the LMR-NMC cathode, the anode is either graphite or a graphite-silicon blend. Lithium metal is also an emerging anode material. This report documents the material and energy flows of producing each of these cathode and anode materials from raw material extraction through the preparation stage. For some cathode materials, we considered solid state and hydrothermal preparation methods. Further, we used Argonne National Laboratory’s Battery Performance and Cost (BatPaC) model to determine battery composition (e.g., masses of cathode, anode, electrolyte, housing materials) when different cathode materials were used in the battery. Our analysis concluded that cobalt- and nickel-containing compounds are the most energy intensive to produce.

Dunn, Jennifer B.↗

Three-dimensional microstructural analysis of fragmentation behavior of platelet Al3Ti particles in Al-Al3Ti composite deformed by equal-channel angular pressing

Highlights: • Particle distribution in ECAPed Al-Al{sub 3}Ti composite depends on material flow of matrix. • Fragmentation of Al{sub 3}Ti particles by ECAP occurs along twin boundary in the particles. • Al{sub 3}Ti particles in the composite fragment after twin deformation of the particles. - Abstract: The fragmentation of platelet Al{sub 3}Ti particles in an Al-Al{sub 3}Ti composite by equal-channel angular pressing (ECAP) is investigated using three-dimensional (3D) microstructural evaluation and crystallography. The Al-Al{sub 3}Ti composite comprises coarse platelet Al{sub 3}Ti particles in an α-Al matrix. The ECAP of this composite is performed for up to 4 passes under processing routes A, B{sub c}, and C. Route B{sub c} produces the smallest Al{sub 3}Ti particle fragments in comparison with the fragments produced under routes A and C. This is because that route B{sub c} produces the largest number of shearing directions and shearing planes. Platelet Al{sub 3}Ti particle fragments in the specimen deformed by ECAP under route A are homogeneously distributed along the deformation axis. In contrast, in the specimens deformed by four ECAP passes under routes B{sub c} and C, the Al{sub 3}Ti particle fragments are gathered into several groups. The fragment groups have a length similar to the initial length of the platelet Al{sub 3}Ti particles. These spatial distributions of particle fragments can be explained by material flow of α-Al matrix during ECAP. Moreover, from 3D microstructural evaluation and crystallographic analysis of the Al{sub 3}Ti particle fragments, it is found that the Al{sub 3}Ti particles are preferentially fragmented on the twin boundary plane of {112}{sub Al3Ti}. Therefore, it is concluded that fragmentation of a platelet Al{sub 3}Ti particle by ECAP occurs along the twin boundary plane after twin deformation.

36 MATERIALS SCIENCE↗

Evaluation of performance indicators applied to a material recovery facility fed by mixed packaging waste

Highlights: • Material Flows assessment of a Material Recovery Facility has been realized. • Performance Indicators for a generic MRF have been proposed. • A Dashboard has been utilized to measure the facility performance. • Experimental values of incoming waste and output products composition are reported. - Abstract: Most of the integrated systems for municipal solid waste management aim to increase the recycling of secondary materials by means of physical processes including sorting, shredding and reprocessing. Several restrictions prevent from reaching a very high material recycling efficiency: the variability of the composition of new-marketed materials used for packaging production and its shape and complexity are critical issues. The packaging goods are in fact made of different materials (aluminium, polymers, paper, etc.), possibly assembled, having different shape (flat, cylindrical, one-dimensional, etc.), density, colours, optical properties and so on. These aspects limit the effectiveness and efficiency of the sorting and reprocessing plants. The scope of this study was to evaluate the performance of a large scale Material Recovery Facility (MRF) by utilizing data collected during a long period of monitoring. The database resulted from the measured data has been organized in four sections: (1) data related to the amount and type of inlet waste; (2) amount and composition of output products and waste; (3) operating data (such as worked hours for shift, planned and unscheduled maintenance time, setting parameters of the equipment, and energy consumption for shift); (4) economic data (value of each product, disposal price for the produced waste, penalty for non-compliance of products and waste, etc.). A part of this database has been utilized to build an executive dashboard composed by a set of performance indicators suitable to measure the effectiveness and the efficiency of the MRF operations. The dashboard revealed itself as a powerful tool to support managers and engineers in their decisions in respect to the market demand or compliance regulation variation as well as in the designing of the lay-out improvements. The results indicated that the 40% of the input waste was recovered as valuable products and that a large part of these (88%) complied with the standards of the recycling companies. The evaluation of the indicators led to the decision to modify the layout to improve the interception of some polymers for which the performance indicators were poor. In particular, two additional optical sorters have to be inserted to increase the yield indicator and to the overall performance of the facility. Definitely, the results of the work allowed to: increase the yield and purity of products’ flows; ensure the compliance of waste flows; increase the workability.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Global patterns of forest autotrophic carbon fluxes

Carbon (C) fixation, allocation, and metabolism by trees set the basis for energy and material flows in forest ecosystems and define their interactions with Earth’s changing climate. However, we lack a cohesive synthesis on how forest carbon fluxes vary globally with respect to climate and one another. Here, we draw upon 1,319 records from the Global Forest Carbon Database (ForC), representing all major forest types and the nine most significant autotrophic carbon fluxes, to comprehensively explore how C cycling in mature, undisturbed forests varies with latitude and climate on a global scale. We show that, across all flux variables analyzed, C cycling decreases continuously with absolute latitude – a finding that confirms multiple previous studies but contradicts the idea that net primary productivity of temperate forests rivals that of tropical forests. C flux variables generally displayed similar trends across latitude and multiple climate variables, with no differences in allocation detected at this global scale. Temperature variables in general, and mean annual temperature and temperature seasonality in particular, were the best univariate predictors of C flux, explaining 19 - 71% of variation in the C fluxes analyzed. The effects of temperature were modified by moisture availability, with C flux reduced under hot and dry conditions and sometimes under very high precipitation. C fluxes increased with growing season length, but this was never the best univariate predictor. Within the growing season, the influence of climate on C cycling was small but significant for a number of flux variables. These findings clarify how forest C flux varies with latitude and climate on a global scale. In a period of accelerating climatic change, this improved understanding of the fundamental climatic controls on forest C cycling sets a foundation for understanding patterns of change.

Banbury Morgan, Rebecca↗

Current limitations and challenges in nanowaste detection, characterisation and monitoring

Highlights: • First review on detection of nanomaterials in complex waste samples. • Focus on nanoparticles in solid, liquid and gaseous waste samples. • Summary of current applicable methods for nanowaste detection and characterisation. • Limitations and challenges of characterisation of nanoparticles in waste. - Abstract: Engineered nanomaterials (ENMs) are already extensively used in diverse consumer products. Along the life cycle of a nano-enabled product, ENMs can be released and subsequently accumulate in the environment. Material flow models also indicate that a variety of ENMs may accumulate in waste streams. Therefore, a new type of waste, so-called nanowaste, is generated when end-of-life ENMs and nano-enabled products are disposed of. In terms of the precautionary principle, environmental monitoring of end-of-life ENMs is crucial to allow assessment of the potential impact of nanowaste on our ecosystem. Trace analysis and quantification of nanoparticulate species is very challenging because of the variety of ENM types that are used in products and low concentrations of nanowaste expected in complex environmental media. In the framework of this paper, challenges in nanowaste characterisation and appropriate analytical techniques which can be applied to nanowaste analysis are summarised. Recent case studies focussing on the characterisation of ENMs in waste streams are discussed. Most studies aim to investigate the fate of nanowaste during incineration, particularly considering aerosol measurements; whereas, detailed studies focusing on the potential release of nanowaste during waste recycling processes are currently not available. In terms of suitable analytical methods, separation techniques coupled to spectrometry-based methods are promising tools to detect nanowaste and determine particle size distribution in liquid waste samples. Standardised leaching protocols can be applied to generate soluble fractions stemming from solid wastes, while micro- and ultrafiltration can be used to enrich nanoparticulate species. Imaging techniques combined with X-ray-based methods are powerful tools for determining particle size, morphology and screening elemental composition. However, quantification of nanowaste is currently hampered due to the problem to differentiate engineered from naturally-occurring nanoparticles. A promising approach to face these challenges in nanowaste characterisation might be the application of nanotracers with unique optical properties, elemental or isotopic fingerprints. At present, there is also a need to develop and standardise analytical protocols regarding nanowaste sampling, separation and quantification. In general, more experimental studies are needed to examine the fate and transport of ENMs in waste streams and to deduce transfer coefficients, respectively to develop reliable material flow models.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Arcjets for Aerodynamic and Materials Testing: Flow Characterization

Potential use of Arcjets as a hypersonic ground test facility for aerodynamic testing of future space vehicles is examined. Since high fidelity simulation of flight freestream conditions is a basic requirement for any useful ground test facility, it is imperative that the Arcjet flow field be thoroughly investigated in a systematic and orderly manner. At the same time we must know how and to what extent an inaccurate simulation of the flight freestream will effect the test data. The paper after discussing these two topics, describes various experimental techniques for Arcjet flow characterization. Results from an on-going Arcjet flow characterization program are also presented.

Sharma, Surendra P.↗