Search NASA⌕ Search

SEARCH · Search NASA

Results for “mechanical performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High Temperature Mechanical Behavior of Refractory Alloys with Digital Image Correlation

Gas turbine efficiency is typically limited by the maximum allowable temperature for components at the inlet side and in the hot gas flow. Refractory alloys and SiC/SiC ceramic-matrix composites (CMCs) are promising candidates for advancing operating temperatures beyond those of Ni-based alloys (>1200 °C). Refractory alloys are more suitable than SiC/SiC CMCs for dynamic components, due to the latter's low toughness and ductility. However, it is well known that refractory alloys suffer from poor oxidation behavior under service lifetimes and conditions, leading to embrittlement concerns. The ARPA-E ULTIMATE program has set out to combine new alloys with advanced coatings to mitigate oxidation/embrittlement effects, while increasing the mechanical performance benefits of refractory materials. Low oxygen (inert gas) or vacuum systems are needed to assess high temperature mechanical performance of developed alloys. To investigate the environmental sensitivity of candidate alloys and develop high temperature testing capabilities, four argon tensile frames were upgraded as well as a single vacuum system at Oak Ridge National Laboratory. Digital image correlation was incorporated into the vacuum frame allowing for surface strain determination and refined insight into thermomechanical response. Creep testing was performed at 1300 °C on two alloys, C-103 and MHC in vacuum and high purity argon environments. The Mo-based alloy showed less sensitivity to oxygen, indicating that testing in well-controlled argon environments may be suitable. The C-103 alloy demonstrated a stronger sensitivity to oxygen in the well-controlled argon environment, illustrating the need for the developed vacuum testing capabilities. “Small” 25 mm and “large” 76 mm MHC specimens showed comparable results in terms of strain rate during creep testing and ultimate tensile strength during tensile testing, suggesting the viability of smaller geometries that use less material of advanced developmental alloys.

Bell, Sam↗
DOE OSTI2021

Thermal and Mechanical Energy Performance Analysis of Closed-loop Systems in Hot-Dry-Rock and Hot-Wet-Rock Reservoirs

To understand the potential and limitations for recovering thermal and mechanical energy from closed-loop geothermal systems a collaborative study is underway that will investigate an array of system configurations, working fluids, geothermal reservoir characteristics, operational periods, and heat transfer enhancements. Closed-loop geothermal systems are distinguished from hydrothermal or enhanced geothermal systems (EGS) in that the working fluid only circulates through drilled boreholes. Principal objectives of this study are to determine upper limits for thermal and mechanical energy recovery and optimal operational and configuration parameters for each scenario. Teams of scientists and engineers are applying a suite of numerical simulation and analytical tools to model the heat recovery from closed-loop geothermal systems, and then optimizing operational and configuration parameters to maximize the thermal and mechanical energy recovery. Results from the suite of numerical simulators and analytical tools, such as outlet and inlet states and temperature profiles in the geothermal reservoir over time are intercompared to increase confidence in the analysis. This paper documents the study findings for closed-loop systems in hot-dry-rock and hot-wet-rock reservoirs, where water is the working fluid. The characteristics of the hot-dry-rock reservoir were based on the U.S. Department of Energy's Utah Frontier Observatory for Research in Geothermal Energy (FORGE) site, near Milford Utah. Two objective functions are defined to optimize the operational and configuration parameters of the system, one each for the recovery of mechanical and thermal energy over the period of operation. For both objective functions, a surface plant thermal to mechanical energy conversion factor and an energy drilling cost is required. In keeping with the study objectives the surface plant conversion factor is determined from a second-law of thermodynamics analysis of a generic binary plant, and drilling costs are based on those from the Utah FORGE site and current national electrical costs.

closed-loop geothermal systems↗
DOE OSTI2021

Thermal and Mechanical Energy Performance Analysis of Closed-loop Systems in Hot-Dry-Rock and Hot-Wet-Rock Reservoirs

To understand the potential and limitations for recovering thermal and mechanical energy from closed-loop geothermal systems a collaborative study is underway that will investigate an array of system configurations, working fluids, geothermal reservoir characteristics, operational periods, and heat transfer enhancements. Closed-loop geothermal systems are distinguished from hydrothermal or enhanced geothermal systems (EGS) in that the working fluid only circulates through drilled boreholes. Principal objectives of this study are to determine upper limits for thermal and mechanical energy recovery and optimal operational and configuration parameters for each scenario. Teams of scientists and engineers are applying a suite of numerical simulation and analytical tools to model the heat recovery from closed-loop geothermal systems, and then optimizing operational and configuration parameters to maximize the thermal and mechanical energy recovery. Results from the suite of numerical simulators and analytical tools, such as outlet and inlet states and temperature profiles in the geothermal reservoir over time are intercompared to increase confidence in the analysis. This paper documents the study findings for closed-loop systems in hot-dry-rock and hot-wet-rock reservoirs, where water is the working fluid. The characteristics of the hot-dry-rock reservoir were based on the U.S. Department of Energy’s Utah Frontier Observatory for Research in Geothermal Energy (FORGE) site, near Milford Utah. Two objective functions are defined to optimize the operational and configuration parameters of the system, one each for the recovery of mechanical and thermal energy over the period of operation. For both objective functions, a surface plant thermal to mechanical energy conversion factor and an energy drilling cost is required. In keeping with the study objectives the surface plant conversion factor is determined from a second-law of thermodynamics analysis of a generic binary plant, and drilling costs are based on those from the Utah FORGE site and current national electrical costs.

Closed-loop geothermal systems, hot-dry-rock, hot-↗
DOE OSTI2024

Epoxy Coating of Biofiber: An Effective Modifier of Biofiber Physical and Flow Properties for Improved Tensile Behavior of Biofiber-Reinforced Biocomposite

Biocomposites combine renewable, plant-based fibers with degradable polymers and are an attractive option for sustainable, lightweight, and cost-effective materials with a low carbon footprint, especially for large-scale additive manufacturing. One of the major challenges in the widespread adoption of biocomposites is that their mechanical performance is significantly inferior to that of synthetic composites. Surface treatment is a common and effective technique to improve the mechanical properties of the biofibers used in biocomposites. This study aims to investigate the physical and flow properties of surface-treated biofibers, as well as the tensile properties of their PLA-based biocomposite, to gain insights into how surface treatment changes the fiber‘s characteristics and biocomposite‘s mechanical properties. Surface treatment was created using a two-component epoxy system by reacting poly(bisphenol A-co-epichlorohydrin) glycidyl end-capped (PBG) and dicyandiamide (DICY). The treatment was tested on two different biofibers (loblolly pine and corn stover fibers) with three different PBG/DICY molar ratios (0.25, 0.5, and 2). Results showed that surface-treated fibers improved the tensile strength and Young‘s modulus of the biocomposites. Loblolly pine biocomposites from fibers treated with a PBG/DICY ratio of 0.25 exhibited the best tensile properties. The surface treatment resulted in a more loosely dispersed fiber bulk structure, as evidenced by less fiber agglomeration into smaller particle sizes, higher fiber sphericity, and lower loose bulk density. This can enhance stress distribution and the overall mechanical performance of the biocomposites. Additionally, surface-treated fibers exhibited better dynamic flow properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Summary report on the mechanical testing performed at INL for creep rupture, fatigue, creep-fatigue, and aging of A709 base material

The report provides the status of the creep, fatigue, and creep-fatigue testing to conducted at Idaho National Laboratory to generate a data package to support Alloy 709 qualification in American Society of Mechanical Engineers, Boiler and Pressure Vessel Code, Section III, Division 5. These tests were performed on three commercial heats of plate material. The first procured heat was manufactured by G.O. Carlson with heat number 58776. Second and third heats were fabricated by ATI Specialty Rolled Products, with heat numbers 529900 and 530843, respectively. A series of creep and cyclic specimens were fabricated from these three heats, and tests were performed. This report presents a master list of all completed and ongoing creep, fatigue, and creep fatigue tests. Cyclic properties of three commercial heats are compared. Thermal aging of three commercial heats for 3000 hours were completed in FY 2025. The thermal aging campaign to age plate material from three commercial heats up to 100,000 hours is ongoing.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Thermo-mechanical characterization of shale using nanoindentation

Abstract Shale can be a potential buffer for high-level radioactive nuclear wastes. To be an effective buffer while subject to waste heat, shale's mechanical response at elevated temperature must be known. Many researchers have experimentally characterized the mechanical behavior of various shales at different length scales in adiabatic conditions. However, its mechanical performance at elevated temperatures at the nano-scale remains unknown. To investigate the temperature dependency of nanomechanical properties of shale, we conducted both experimental and numerical studies. In this study, we measured mechanical and fracture properties of shale, such as hardness, elastic modulus, anisotropy, and fracture toughness from 25 °C up to 300 °C at different bedding planes. Statistical analysis of the results suggests that hardness and fracture toughness significantly increased at temperatures from 100 to 300 °C; while, temperature does not have a significant impact on elastic modulus. Data also shows that the bedding plane orientations have a substantial impact on both mechanical and fracture properties of shale at the nano-scale leading to distinct anisotropic behavior at elevated temperature below 100 °C. Additionally, we numerically investigated the mechanical performance of the shale samples at room temperature to gain an insight into its mechanical response through the thickness. Numerical results were validated against the experimental results, confirming the simulation can be used to predict shale deformation at the nano-scale or potentially be used in multi-scale simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Binder-jetted AISI M2 tool steel during hot isostatic pressing: Densification and carbide transformation

Binder jetting (BJ) enables fabrication of complex components from high-alloy steels such as AISI M2; however, residual porosity after sintering limits mechanical performance. This study investigates the coupled effects of binder chemistry, sintering conditions, cooling rate, and subsequent hot isostatic pressing (HIP) on densification, microstructure, and mechanical response in binder-jetted M2 tool steel. HIP increased relative density from ∼93 to 95% to >99% and improved compressive strength by ∼40-70%. Densification was governed by initial pore morphology, where closed porosity was effectively eliminated, while interconnected porosity limited full consolidation. Microstructural analysis (XRD, EBSD, SEM) shows that HIP promotes dissolution of metastable carbides and redistribution of alloying elements (W, Mo, V), transforming heterogeneous carbide networks into finer and more uniformly distributed M 2 C, MC, and M 6 C phases through diffusion-assisted homogenization. Among the investigated conditions, the FluidFuse binder combined with sintering at 1270 °C for 60 min and furnace cooling produced the most balanced response, achieving ∼99.7% density, ∼855 HV hardness, ∼4130 MPa compressive strength, and ∼24% strain. In contrast, higher sintering temperatures promoted carbide coarsening, reducing ductility despite high density. HIP reduces microstructural heterogeneity and drives the system toward a near-equilibrium state with reduced sensitivity to prior processing history. A comparative assessment with conventional and additive manufacturing routes (LPBF, DED, EBM, FFF) shows that the BJ-HIP approach achieves competitive densification and mechanical performance. These findings provide a mechanistic basis for controlling densification and microstructure in high-alloy steels processed via BJAM.

AISI M2 tool steel↗
DOE OSTI2023

Effect of Interlayer Time-Lapse and Workability Retention on Printed Concrete Performance

The rapid advancement of additive manufacturing technologies for concrete construction requires further understanding of material performance and its relationship with print parameters such as interlayer time-lapse and workability retention during the print. Here this study addresses the effects of the time delay between consecutive extruded layers on the mechanical performance of printed concrete using a mix designed by Quikrete. A series of specimens were prepared with printing delays of 10, 15, 30, and 60 min. This work correlates the change in fracture properties, mechanical performance, and workability retention with the interlayer time-lapse between two consecutive concrete layers. Interlayer time-lapse is defined as the time difference in printing of two consequent layers of concrete. It affects individual properties differently based on the loading direction and test types, but it is consistent in terms of interlayer performance. The understanding of the effect of interlayer time-lapse on the fracture properties between two consecutive printed layers fills the knowledge gaps in printed concrete research. Therefore, this study can help researchers perform required optimization and safely estimate the performance of printed concrete.

3D printing↗
DOE OSTI2022

Dual–Interface–Reinforced Flexible Perovskite Solar Cells for Enhanced Performance and Mechanical Reliability

Two key interfaces in flexible perovskite solar cells (f-PSCs) are mechanically reinforced simultaneously: one between the electron-transport layer (ETL) and the 3D metal-halide perovskite (MHP) thin film using self-assembled monolayer (SAM), and the other between the 3D-MHP thin film and the hole-transport layer (HTL) using an in situ grown low-dimensional (LD) MHP capping layer. The interfacial mechanical properties are measured and modeled. This rational interface engineering results in the enhancement of not only the mechanical properties of both interfaces but also their optoelectronic properties holistically. As a result, the new class of dual-interface-reinforced f-PSCs has an unprecedented combination of the following three important performance parameters: high power-conversion efficiency (PCE) of 21.03% (with reduced hysteresis), improved operational stability of 1000 h T90 (duration at 90% initial PCE retained), and enhanced mechanical reliability of 10 000 cycles n88 (number of bending cycles at 88% initial PCE retained). Furthermore, the scientific underpinnings of these synergistic enhancements are elucidated.

14 SOLAR ENERGY↗
NASA NTRS1990

PASS Spacecraft Antenna Technology Assessment

The purpose was to generate estimates of mechanical performance for the classes of spacecraft antenna under construction for application to the Personal Access Satellite System (PASS). These performance data are needed for the support of trade studies involving antenna system development. The classes of antenna considered included: (1) rigid non-deployable antenna structures; (2) mechanical deployable antenna concepts; (3) inflatable deployable antenna concepts; and (4) mesh deployable antenna concepts. The estimates of mechanical performance are presented in terms of structural weight and cost as a function of the reflector size. Estimates of aperture surface precision are presented for a few discrete antenna sizes. The range of reflector size is 1 to 4 meters for non-deployable structures and 2 to 8 meters for deployable structures. The range of reflector surface precision is lambda/30 to lambda/50 for 20 and 30 GHz, respectively.

Freeland, R. E.↗
DOE OSTI2021

Passive sensing of a microparticle modified hybrid, fiber-reinforced composite

The widespread commercial adoption of high-performance, fiber-reinforced composites has pushed research interests toward the next generation of composites. These new composites are tasked with integrating additional functionalities into the structures without causing a trade-off in mechanical performance. One such functionality that has received significant interest is sensing. This is especially important for composites using high-performance fibers (e.g., carbon fiber) because their strain-to-failure is relatively low, resulting in brittle fracture. Besides, fiber damage can be hidden within the composite, potentially leading to premature catastrophic failure if not detected. In prior research, we demonstrated continuous feed-through deposition of ceramic nanoparticles on carbon fiber’s surface that simultaneously enhanced both the piezoresistive response and interlaminar shear strength. In this work, a similar continuous feed-through deposition process was used to demonstrate passive sensing and energy harvesting by integrating ferroelectric microparticles on the surface of electrically nonconductive fibers. The sensing and energy harvesting capabilities were characterized by mechanically straining composite beams and measuring the power generated. The improvements in mechanical properties are shown through interlaminar shear strength tests. Therefore, this research aims to demonstrate a high throughput, commercially scalable approach to coat fibers with ferroelectric microparticles that enable passive sensing as well as improved mechanical performance when fabricated into a fiber-reinforced composite.

Bowland, Christopher↗
DOE OSTI2024

Improving the Recyclability of Polymer Composites With Cellulose Nanofibrils

Cellulose nanofibers (CNFs) have been widely studied for their reinforcing potential in high-performance composites. While there are numerous publications on CNF-reinforced composites in a variety of polymer matrices, few have considered the recyclability of such thermoplastic composites and whether the incorporation of CNFs deteriorates or improves their performance upon reprocessing. In this study, two thermoplastic resins, poly(lactic acid) (PLA), and glycol-modified polyethylene terephthalate (PETg), were prepared with CNF reinforcement and thermomechanically recycled to investigate the effect of CNF inclusion on the composite properties after reprocessing as well as their effect on the composites’ number of useful life cycles. Additionally, changes in mechanical, thermal, rheological, molecular, and microstructural properties of the composites and/or base resins were monitored as a function of cycle numbers. As is typical, the polymers’ molecular weight and mechanical performance deteriorated with continued processing. However, the addition of spray dried CNF was found to better maintain the mechanical performance of both polymers throughout multiple recycling steps as compared to neat samples. For example, the tensile strength of PETg with 20 wt% CNF after 6 processing cycles was found to exceed that of virgin neat PETg, and higher loadings of CNF were found to preserve a higher yield strength during multiple rounds of reprocessing compared to PETg composites with lower CNF loadings. Ultimately this study indicates that the addition of CNF to some thermoplastic materials can increase both their sustainability by offsetting the use of high-embodied energy resins and their circularity by enabling performance retention over more use cycles.

42 ENGINEERING↗
DOE OSTI2024

Sensitization and Mechanical Response of Cu‐Containing Steel Rods

The iron and steel manufacturing sector significantly adds to global greenhouse gas emissions, caused primarily by the carbothermic reduction of iron ore. Recycling scrap steel offers an effective decarbonization strategy but introduces impurities like copper (Cu) that can negatively impact mechanical properties. This study investigates the effects of Cu content and heat treatment on the mechanical performance and sensitization of steel wire rods for tire manufacturing. Steel rods with 0.04 and 0.21 wt% Cu are heated to 1050 or 1200 °C, then air quenched, or furnace cooled. Tensile testing coupled with microscopic analysis is used to evaluate mechanical properties and assess the sensitization effects. Higher Cu content leads to larger sensitized zones with increased Cu precipitation along grain boundaries. Ductility and toughness, crucial for wire drawability, are found to be reduced, despite higher ultimate strength. Slower furnace cooling is seen to result in smaller sensitized zones compared to air quenching, suggesting a pivotal role of cooling rate in sensitization control. The findings provide insights into optimize heat treatment parameters and Cu content limits, balancing mechanical performance and maintaining drawability for enhanced scrap steel recycling in tire production.

copper↗
DOE OSTI2022

Mechanical joint performances of friction self-piercing riveted carbon fiber reinforced polymer and AZ31B Mg alloy

Carbon fiber reinforced polymer (CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting (F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load and mechanical interlock distance increased. Ultrafine grains were formed at the joint in AZ31B as a result of dynamic recrystallization, which contributed to the higher hardness. Fatigue life of the CFRP-AZ31B joint was studied at various peak loads of 0.5, 1, 2, and 3 kN and compared with the resistance spot welded AZ31B-AZ31B from the open literature. The fatigue performance was better at higher peak load (>2 kN) and comparable to that of resistance spot welding of AZ31B to AZ31B at lower peak loads (<1 kN). From fractography, the crack initiation for lower peak load (<1 kN) case was observed at the fretting positions on the top and bottom surfaces of AZ31B sheet. When peak load was increased, fretting between the rivet and the top of AZ31B became more dominant to initiate a crack during fatigue testing.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Geo-Responsive Chemomechanics in Aluminum Oxyhydroxide via Alkali-Driven Dehydroxylation for Supercritical Geothermal Systems

Widespread use of enhanced geothermal systems can revolutionize global renewable electrical power access, yet its advancement is hindered by the inherent instability of Portland cement-based chemistries for geothermal well construction under high-temperature corrosive conditions. Here, in this work, we demonstrate the tunable mechanical performance of aluminum oxyhydroxides as cementitious materials through an alkali-controlled dehydroxylation reaction pathway for long-term applications under supercritical geothermal environments. Notably, the synthesized aluminum oxyhydroxides demonstrate remarkable stability, maintaining superior mechanical performance under supercritical conditions for over 30 days. Synchrotron X-ray diffraction, spectroscopy measurements and geochemical thermodynamic modeling uncover that the gibbsite dehydroxylation pathway functions as a key dial for tuning the chemomechanics, rendering the aluminum oxyhydroxide a strong cementitious material. By uncovering the mechanistic role of alkali-driven dehydroxylation, this work proposes a cementitious chemistry distinct from conventional Portland cement and geopolymer-dominated alkali-activated systems, laying the groundwork for developing next-generation cementitious materials for supercritical geothermal energy exploitation.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Agrivoltaic Racking Design Optimization Based on Wind and Snow Loading Finite Element Analysis

The racking structure of photovoltaic (PV) systems plays a critical role in ensuring the PV panels generate power properly as it provides integral structural support and sometimes even solar tracking ability. Distinct applications of PV systems require variations of racking structure designs, which yield different mechanical performances under external loading conditions from the environment, such as heavy wind and snow. Past works, such as Reddy et al. [1], have analyzed the pressure effects of wind and snow loading on the racking structure of conventional rooftop and utility PV systems, but there is little knowledge of how various agrivoltaic racking systems perform, in terms of stress and strain, under the same loading conditions. There is also a knowledge gap in the industry on a set of optimized agrivoltaic racking design standards. This study investigates the mechanical performance of various existing racking systems and proposes novel designs that are optimized for agrivoltaics applications under wind and snow loading.

Liao, Quanhuan↗
DOE OSTI2022

Solid Phase Processing of Lead-Free Brass with Carbon Additives

Currently, “lead-free” brass alloys (like C27450/C27451/C6930), used extensively in drinking water fixtures and automotive, electrical, and electronic applications contain maximum 0.25% lead to maintain mechanical performance and machinability. Adding graphite to brass as an alternative to lead, using casting, powder metallurgy, and extrusion methods, has been explored previously. However, all these methods have proven to be energy-, time-, and resource-intensive, while not enabling performance equivalent to that of C36000 brass. In this project, we developed a one-step approach using friction extrusion and ShAPE to make lead-free brass/graphite components such as wires, rods and tubes with mechanical performance equivalent to commercial lead-free brass alloys. Manufacturing temperatures were maintained ~550-730 °C with feed rates ranging between 4 – 25 mm/min. Results show larger grains at the center of the rods and wires with smaller grains developing at the edges. Graphite particles were sheared in the direction of extrusion with higher strains observed towards the edges. Hardness of the brass/graphite samples was over 25% higher than that of the corresponding brass-only samples (rods and wires), also friction extruded. Our results show that the sub-micron graphite plays an important role in limiting process temperature and restraining grain growth during friction extrusion, thus reducing grain size in composites.

36 MATERIALS SCIENCE↗