Search NASA⌕ Search

SEARCH · Search NASA

Results for “mechanical switching devices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Design and Testing of a Dynamically-Tuned Magnetostrictive Spring with Electrically-Controlled Stiffness

This paper details the development of an electrically-controlled, variable-stiffness spring based on magnetostrictive materials. The device, termed a magnetostrictive Varispring, can be applied as a semi-active vibration isolator or switched stiffness vibration controller for reducing transmitted vibrations. The Varispring is designed using 1D linear models that consider the coupled electrical response, mechanically-induced magnetic diffusion, and the effect of internal mass on dynamic stiffness. Modeling results illustrate that a Terfenol-D-based Varispring has a rise time almost an order of magnitude smaller and a magnetic diffusion cut-off frequency over two orders of magnitude greater than a Galfenol-based Varispring. The results motivate the use of laminated Terfenol-D rods for a greater stiffness tuning range and increased bandwidth. The behavior of a prototype Varispring is examined under vibratory excitation up to 6 MPa and 25 Hz using a dynamic load frame. For this prototype, stiffness is indirectly varied by controlling the excitation current. Preliminary measurements of continuous stiffness tuning via sinusoidal currents up to 1 kHz are presented. The measurements demonstrate that the Young's modulus of the Terfenol-D rod inside the Varispring can be continuously varied by up to 21.9 GPa. The observed stiffness tuning range is relatively constant up to 500 Hz, but significantly decreases thereafter. The stiffness tuning range can be greatly increased by improving the current and force control such that a more consistent current can be applied and the Varispring can be accurately tested at a more optimal bias stress.

Vibration control↗
DOE OSTI2020

Uncovering phase transformation, morphological evolution, and nanoscale color heterogeneity in tungsten oxide electrochromic materials

Controlling the electrochemical interfacial processes that govern the durability of electrochromic devices represents a key challenge in developing sustainable and cost-effective smart windows. Here, we revisit the classical tungsten trioxide (WO 3 ) materials as a platform to uncover the previously unknown interrelationship between phase transformation, morphological evolution, and nanoscale color heterogeneity in these materials. Through synchrotron/electron spectroscopic and imaging analyses, we report that the WO 3 –electrolyte interface is influenced by the tungsten dissolution and redeposition during the electrochemical cycling. The tungsten redeposition provokes the in situ crystal growth, which ultimately leads to the phase transformation from the semicrystalline WO 3 to a nanoflake-shaped, proton-trapped tungsten trioxide dihydrate (H x WO 3 · 2 H 2 O). The multidimensional quantification of the electronic structure reveals that the tungsten reduction caused by the proton trapping is heterogeneous at the nanometric scale and is responsible for the nanoscale color heterogeneity. The interplay between phase transformation, morphological evolution, and nanoscale color heterogeneity results in degraded optical modulation, switching kinetics, coulombic efficiency, and bleached-state transparency. Our results highlight that the high interfacial reactivity near the electrode surface may be the underlying mechanism for undesired bulk structural changes of electrochromic materials, and calls for fundamental studies in probing and controlling the electrode–electrolyte interfacial processes in electrochromic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Direct Observation of Room–Temperature Magnetic Skyrmion Motion Driven by Ultra–Low Current Density in Van Der Waals Ferromagnets

The recent discovery of room-temperature ferromagnetism in 2D van der Waals (vdW) materials, such as Fe 3 GaTe 2 (FGaT), has garnered significant interest in offering a robust platform for 2D spintronic applications. Various fundamental operations essential for the realization of 2D spintronics devices are experimentally confirmed using these materials at room temperature, such as current-induced magnetization switching or tunneling magnetoresistance. Nevertheless, the potential applications of magnetic skyrmions in FGaT systems at room temperature remain unexplored. In this work, the current-induced generation of magnetic skyrmions in FGaT flakes employing high-resolution magnetic transmission soft X-ray microscopy is introduced, supported by a feasible mechanism based on thermal effects. Furthermore, direct observation of the current-induced magnetic skyrmion motion at room temperature in FGaT flakes is presented with ultra-low threshold current density. This work highlights the potential of FGaT as a foundation for room-temperature-operating 2D skyrmion device applications.

2D ferromagnets↗
DOE OSTI2025

A Study on the Impact of Temperature-Dependent Ferroelectric Switching Behavior in 3D Memory Architecture

The flourishing development of neural networks that require exponentially growing amounts of data has presented an elevated demand for memory footprint. To address this, researchers have been exploring hardware accelerators with innovative memory architectures like 3D memory. These 3D memory architectures offer enhanced storage capacity and processing capabilities, at a cost of rising on-chip temperature during operation. Hafnium Zirconium Oxide (HZO) based Ferroelectric Random Access Memory (FeRAM) is a promising nonvolatile memory candidate in neural network hardware accelerators for its outstanding write performance and reliability. However, its implementation in the architecture regarding the temperature-dependent ferroelectric switching behavior has not been well studied. In this work, we study the thermal impacts on polarization switching through experimental devices and simulation results. We conduct the circuit and architecture-level simulations to showcase that one can exploit this temperature rise to reduce FeRAM's write voltage and write energy due to its unique temperature-activated polarization switching mechanisms. As the on-chip temperature increases to 351K (ambient temperature at 300K) due to neural network workloads, the access energy per bit can be reduced by 27.6% when a dynamic write voltage is applied.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermodynamic origin of nonvolatility in resistive memory

Electronic switches based on the migration of high-density point defects, or memristors, are poised to revolutionize post-digital electronics. Despite significant research, key mechanisms for filament formation and oxygen transport remain unresolved, hindering our ability to predict and design device properties. For example, experiments have achieved 10 orders of magnitude longer retention times than predicted by current models. Here, using electrical measurements, scanning probe microscopy, and first-principles calculations on tantalum oxide memristors, we reveal that the formation and stability of conductive filaments crucially depend on the thermodynamic stability of the amorphous oxygen-rich and oxygen-poor compounds, which undergo composition phase separation. Including the previously neglected effects of this amorphous phase separation reconciles unexplained discrepancies in retention and enables predictive design of key performance indicators such as retention stability. Furthermore, this result emphasizes non-ideal thermodynamic interactions as key design criteria in post-digital devices with defect densities substantially exceeding those of today’s covalent semiconductors.

36 MATERIALS SCIENCE↗
NASA NTRS1997

Robotic Assisted Microsurgery - RAMS FY'97

JPL and Microdexterity Systems collaborated to develop new surgical capabilities. They developed a Robot Assisted Microsurgery (RAM) tool for surgeons to use for operating on the eye, ear, brain, and blood vessels with unprecedented dexterity. A surgeon can hold the surgical instrument with motions of 6 degrees of freedom with an accuracy of 25 microns in a 70 cu cm workspace. In 1996 a demonstration was performed to remove a microscopic particle from a simulated eyeball. In 1997, tests were performed at UCLA to compare telerobotics with mechanical operations. In 5 out of 7 tests, the RAM tool performed with a significant improvement of preciseness over mechanical operation. New design features include: (1) amplified forced feedback; (2) simultaneous slave robot instrumentation; (3) index control switch on master handle; and (4) tool control switches. Upgrades include: (1) increase in computational power; and (2) installation of hard disk memory storage device for independent operation and independent operation of forceps. In 1997 a final demonstration was performed using 2 telerobotics simultaneously in a microsurgery suture procedure to close a slit in a thin sheet of latex rubber which extended the capabilities of microsurgery procedures. After completing trials and demonstrations for the FDA the potential benefits for thousands of operations will be exposed.

Source record↗
NASA NTRS2002

Airbag system and method for facilitating emergency egress from an aircraft

An airbag system for elevating the fuselage of an aircraft off a landing surface a sufficient degree to allow for emergency egress of passengers and crew through ventral emergency exit doors. An airbag assembly made up of a plurality of independent airbags is disposed within the aircraft. When activated, the airbag system deploys the airbags external of the aircraft that elevate the fuselage of the aircraft a sufficient degree to allow for utilizing the ventral emergency exit doors on the fuselage to enable evacuating the passengers and crew. An activation mechanism is connected to the inflation.devices associated with each of the airbags. The activation mechanism generates an electrical signal which activates the inflation devices, which in turn fill the airbags with a compressed fluid, thus expanding the airbags and lifting the fuselage. A crew member initiates the activation of the airbag system through one or more switches.

Rawdon, Blaine K.↗
DOE OSTI2022

Filament Formation in TaO x Thin Films for Memristor Device Application: Modeling Electron Energy Loss Spectra and Electron Transport

Abstract Although understanding filament formation in oxide‐based memristive devices by theory has emerged, there are still fundamental unanswered questions. Importantly, for practical application of thin films the material in its amorphous state is to be considered, but mostly lacking so far, and details on sub‐stoichiometry are also scarce. To gain insight into the optical and electronic properties of sub‐stoichiometric amorphous tantalum oxide (TaO x ), the electron energy loss spectrum (EELS) of model systems is characterized theoretically and electron transport characteristics are analyzed in detail. Calculated blue‐shifts by increasing sub‐stoichiometry explained the measurements, potentially suggesting estimation of oxygen vacancy concentrations through EEL spectra. Electron transport results based on TaO x material models validated by EELS measurements show that oxygen vacancy filamentary paths are initiated at low bias upon increasing sub‐stoichiometry yet noting an interplay with the local amorphous structure. Contact resistances at interfaces of the TaO x switching layer and a tantalum scavenging layer or titanium nitride electrode are quantified, indicating the possibility for either oxygen vacancy‐ or metal cluster‐based conduction mechanisms at the interface. The computational work, combined with experimental characterization for validation, provides a basis for investigating effects of sub‐stoichiometry on filament formation in TaO x thin film memristive devices.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Thermal Switch for Satellite Temperature Control

An active radiator tile (ART) thermal valve has been fabricated using silicon micromachining. Intended for orbital satellite heat control applications, the operational principal of the ART is to control heat flow between two thermally isolated surfaces by bring the surfaces into intimate mechanical contact using electrostatic actuation. Prototype devices have been tested in a vacuum and demonstrate thermal actuation voltages as low as 40 volts, very good thermal insulation in the OFF state, and a large increase in radiative heat flow in the ON state. Thin, anodized aluminum was developed as a coating for high infrared emissivity and high solar reflectance.

Ziad, H.↗
NASA NTRS2001

Piezoelectric Vibrational and Acoustic Alert for a Personal Communication Device

An alert apparatus for a personal communication device includes a mechanically prestressed piezoelectric wafer positioned within the personal communication device and an alternating voltage input line coupled at two points of the wafer where polarity is recognized. The alert apparatus also includes a variable frequency device coupled to the alternating voltage input line, operative to switch the alternating voltage on the alternating voltage input line at least between an alternating voltage having a first frequency and an alternating voltage having a second frequency. The first frequency is preferably sufficiently high so as to cause the wafer to vibrate at a resulting frequency that produces a sound perceptible by a human ear, and the second frequency is preferably sufficiently low so as to cause the wafer to vibrate at a resulting frequency that produces a vibration readily felt by a holder of the personal communication device.

Stanley E Woodard↗
DOE OSTI2024

Phase Transformation Driven by Oxygen Vacancy Redistribution as the Mechanism of Ferroelectric Hf 0.5 Zr 0.5 O 2 Fatigue

As a promising candidate for nonvolatile memory devices, the hafnia-based ferroelectric system has recently been a hot research topic. Although significant progress has been made over the past decade, the endurance problem is still an obstacle to its final application. In perovskite-based ferroelectrics, such as the well-studied Pb[Zr x Ti 1-x ]O 3 (PZT) family, polarization fatigue has been discussed within the framework of the interaction of charged defects (such as oxygen vacancies) with the moving domains during the switching process, particularly at the electrode-ferroelectric interface. Armed with this background, a hypothesis is set out to test that a similar mechanism can be in play with the hafnia-based ferroelectrics. The conducting perovskite La-Sr-Mn-O is used as the contact electrode to create La 0.67 Sr 0.33 MnO 3 / Hf 0.5 Zr 0.5 O 2 (HZO)/ La 0.67 Sr 0.33 MnO 3 capacitor structures deposited on SrTiO 3 -Si substrates. Nanoscale X-ray diffraction is performed on single capacitors, and a structural phase transition from polar o-phase toward non-polar m-phase is demonstrated during the bipolar switching process. The energy landscape of multiphase HZO has been calculated at varying oxygen vacancy concentrations. Based on both theoretical and experimental results, it is found that a polar to non-polar phase transformation caused by oxygen vacancy redistribution during electric cycling is a likely explanation for fatigue in HZO.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Structural Phase Transitions between Layered Indium Selenide for Integrated Photonic Memory

The primary mechanism of optical memoristive devices relies on phase transitions between amorphous and crystalline states. The slow or energy-hungry amorphous–crystalline transitions in optical phase-change materials are detrimental to the scalability and performance of devices. Leveraging an integrated photonic platform, nonvolatile and reversible switching between two layered structures of indium selenide (In 2 Se 3 ) triggered by a single nanosecond pulse is demonstrated. The high-resolution pair distribution function reveals the detailed atomistic transition pathways between the layered structures. With interlayer “shear glide” and isosymmetric phase transition, switching between the α- and β-structural states contains low re-configurational entropy, allowing reversible switching between layered structures. Broadband refractive index contrast, optical transparency, and volumetric effect in the crystalline–crystalline phase transition are experimentally characterized in molecular-beam-epitaxy-grown thin films and compared to ab initio calculations. Finally, the nonlinear resonator transmission spectra measure of incremental linear loss rate of 3.3 GHz, introduced by a 1.5 µm-long In 2 Se 3 -covered layer, resulted from the combinations of material absorption and scattering.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal stability and magnetization switching of composite free layer with perpendicular magnetic anisotropy

We present a micromagnetic study of a ferromagnetically exchange-coupled composite free layer design for perpendicular magnetic tunnel junctions. The thermal stability factor and critical switching current density depend on the exchange coupling strength and effective anisotropy ratio between the sublayers of the composite free layer. The energy barrier increases with an increase of the exchange coupling strength until it reaches a plateau in the strong-coupling limit. An optimal exchange coupling strength exists that leads to the minimal critical switching current and a significant improvement of the figure of merit defined as the ratio between the energy barrier and critical switching current. This behavior is obtained for smaller device sizes with uniform reversal and larger sizes with domain wall reversal.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Light-induced Weyl semiconductor-to-metal transition mediated by Peierls instability

Elemental tellurium is a strongly spin-orbit coupled Peierls-distorted semiconductor whose band structure features topologically protected Weyl nodes. Here, using time-dependent density functional theory calculations, we show that impulsive optical excitation can be used to transiently control the amplitude of the Peierls distortion, realizing a mechanism to switch tellurium between three states: Weyl semiconductor, Weyl metal and non-Weyl metal. Further, we present experimental evidence of this inverse-Peierls distortion using time-resolved optical second harmonic generation measurements. These results provide a pathway to multifunctional ultrafast Weyl devices and introduce Peierls systems as viable hosts of light-induced topological transitions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2004

Dynamics and Stability of Capillary Surfaces: Liquid Switches at Small Scales

The dynamics and stability of systems of interfaces is central to a range of technologies related to the Human Exploration and Development of Space (HEDS). Our premise is that dramatic shape changes can be manipulated to advantage with minimal input, if the system is near instability. The primary objective is to develop the science base to allow novel approaches to liquid management in low-gravity based on this premise. HEDS requires efficient, reliable and lightweight technologies. Our poster will highlight our progress toward this goal using the capillary switch as an example. A capillary surface is a liquid/liquid or liquid/gas interface whose shape is determined by surface tension. For typical liquids (e.g., water) against gas on earth, capillary surfaces occur on the millimeterscale and smaller where shape deformation due to gravity is unimportant. In low gravity, they can occur on the centimeter scale. Capillary surfaces can be combined to make a switch a system with multiple stable states. A capillary switch can generate motion or effect force. To be practical, the energy barriers of such a switch must be tunable, its switching time (kinetics) short and its triggering mechanism reliable. We illustrate these features with a capillary switch that consists of two droplets, coupled by common pressure. As long as contact lines remained pinned, motions are inviscid, even at sub-millimeter scales, with consequent promise of low-power consumption at the device level. Predictions of theory are compared to experiment on i) a soap-film prototype at centimeter scale and ii) a liquid droplet switch at millimeter-scale.

Steen, Paul H.↗
NASA NTRS1929

Mechanical control of airplanes

Before undertaking a detailed description of an automatic-control mechanism, I will state briefly the fundamental conditions for such devices. These are: 1) it must be sensitive at one or more reference values; 2) it must stop the angular motions of the airplane not produced by the pilot; and 3) it must be possible to switch it off and on by a simple hand lever.

AUTOMATIC PILOTS - BOYKOW↗
NASA NTRS2006

Helicopter force-feel and stability augmentation system with parallel servo-actuator

A force-feel system is implemented by mechanically coupling a servo-actuator to and in parallel with a flight control system. The servo-actuator consists of an electric motor, a gearing device, and a clutch. A commanded cockpit-flight-controller position is achieved by pilot actuation of a trim-switch. The position of the cockpit-flight-controller is compared with the commanded position to form a first error which is processed by a shaping function to correlate the first error with a commanded force at the cockpit-flight-controller. The commanded force on the cockpit-flight-controller provides centering forces and improved control feel for the pilot. In an embodiment, the force-feel system is used as the basic element of stability augmentation system (SAS). The SAS provides a stabilization signal that is compared with the commanded position to form a second error signal. The first error is summed with the second error for processing by the shaping function.

Hoh, Roger H.↗
NASA NTRS2003

Thermally-Driven Josephson Effect

Break-throughs in the study of superfluid He-3 weak links and recent demonstration of Josephson effect in He-4 are a result of significant advances in ultra-sensitive transducer and nanofabrication technology. However, further progress in the performance of superfluid weak links and quantum rotation interferometry devices depends, in part, on reducing the mechanical noise and increasing the effective duty cycle of such devices. In existing devices, the DC Josephson effect is driven by chemical potential difference produced by a pressure applied across the weak link. We propose a novel drive technique, where the chemical potential is due to a controlled temperature difference. This technique promises to eliminate mechanical shock associated with the switch of the direction of applied pressure and to achieve 100% duty cycle. The thermally driven Josephson effect may also answer outstanding questions about dissipation in superfluid weak links.

Penanen, Konstantin↗