Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Crystal mechanics-based thermo-elastic constitutive modeling of orthorhombic uranium using generalized spherical harmonics and first-order bounding theories

In earlier works, a mathematical procedure for invertible microstructure-property linkages was developed using computationally efficient spectral methods for polycrystalline cubic and hexagonal metals. This paper formulates such invertible microstructure–property linkages for orthorhombic polycrystalline metals relying on the generalized spherical harmonics (GSH) spectral basis. The procedure is used to compute property closures of orthorhombic polycrystals. The closures represent the complete set of theoretically possible combinations of effective properties for a selected material. The procedure relies on the first-order bounding theories and considers orientation distribution functions (ODFs) as the main microstructural descriptor influencing homogenized properties. Numerous examples of these closures involving second-rank thermal expansion and fourth-rank elastic stiffness tensorial properties over a broad range of temperatures are presented for α-uranium (α-U). In doing so, certain key properties of these closures are exploited to facilitate their computation with drastically reduced computational effort. Along with the recently developed GSH-based interpolation procedure for ODFs from coarsely spaced experimental measurement grids to finely spaced finite element mesh resolution grids presented in Barrett et al., the developed computationally efficient ODF-effective property linkages are used to establish a crystal mechanics-based simulation framework coupled with the finite element method (FEM). The ODF dependent thermal expansion and elastic stiffness tensors are efficiently calculated at every integration point and used by the FEM to predict the overall distortion of a hemispherical part made of α-U during heating. In conclusion, it is shown that the developed framework can be used to simulate microstructurally heterogeneous components under thermo-mechanical loadings in a computationally efficient manner.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of secondary void-initiating particles on the steady-state crack growth resistance of high-strength steel

In this investigation, we focus on the dependence of stable crack growth resistance, as measured by the short-rod fracture toughness test, on secondary void-initiating particles such as AlN and Ti-based grain-refining precipitates in a variety of high-strength steels with tempered martensitic microstructures. The model developed by Ritchie and Thompson is modified to illustrate the significant amounts of toughening that can result from the refinement of secondary particles. Analysis of the data suggests that material strength is a predominant factor in increasing the short-rod fracture toughness relative to linear-elastic measures of initiation fracture toughness, but the extent of toughening is limited by the size and number density of secondary particles in the microstructure. The variation in estimates of secondary microvoid initiation and growth strains with precipitate size reinforce the notion that primary fracture at non-metallic inclusions and secondary fracture at smaller particles occur as sequential processes with a degree of concurrence that is dependent on the state of precipitation in both particle dispersions. Toughening in this connection is maximized by increases in microvoid growth strain that result from decreases in the size and areal number density of secondary void-initiating particles. Finally, the occurrence of transient instabilities during crack extension in short-rod specimens is explained with a phenomenological model that relates crack growth stability to natural variations in the dispersion of secondary void-initiating particles in the microstructure.

42 ENGINEERING↗
DOE OSTI2020

Modeling strength and failure variability due to porosity in additively manufactured metals

To model and quantify the variability in plasticity and failure of additively manufactured metals due to imperfections in their microstructure, we have developed uncertainty quantification methodology based on pseudo marginal likelihood and embedded variability techniques. We account for both the porosity resolvable in computed tomography scans of the initial material and the sub-threshold distribution of voids through a physically motivated model. Calibration of the model indicates that the sub-threshold population of defects dominates the yield and failure response. Finally, the technique also allows us to quantify the distribution of material parameters connected to microstructural variability created by the manufacturing process, and, thereby, make assessments of material quality and process control.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Review of internal and external surface finishing technologies for additively manufactured metallic alloys components and new frontiers

Surface finishing in additive manufacturing (AM) is a technological bottleneck. The field of surface finishing of AM parts is vast because it not only focuses on roughness reduction in the hard-to-access internal surfaces but also includes the scope of adding coatings and sensors. Even though metal AM component is reaching the density and bulk microstructure at par or even better than conventionally produced components, adverse impact of surface roughness and imperfections is becoming the major obstruction. It is observed that external and internal surface roughness of AM components is a high probability cause of many unavoidable issues such as corrosion, incorrect tolerance estimations during the build stage, and the fatigue failure of parts before the expected life cycle. At present, AM field mainly focuses on improving and enhancing the internal and external surface roughness to pass the stringent qualification requirements for actual applications. To address these challenges, researchers worldwide are conducting many experiments and developing different surface finishing techniques. This paper reviews the state-of-the-art knowledge and processes of different surface finishing technology that can be applied to AM metal components. This article mainly highlights several liquid-based surfaces finishing approaches to develop promising surface microstructures on interior and exterior surfaces as a micromachining tool. The future of making strong and self-monitoring AM component requires broadening of surface finishing field and including advanced topics such as coatings and adding sensor technology. We also discuss new frontiers and the scope of future work in the surface finishing field to bring attention to related concerns and possibilities associated with making smart and strong AM components for twenty-first-century integrated engineering systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Sensitivity of cellular automata grain structure predictions for high solidification rates

Understanding as-solidified grain structure development during constrained (G 0) alloy solidification conditions is a necessary component of understanding the larger process-microstructure relationships during additive manufacturing (AM) processing. This study applies a cellular automata (CA) model, for static solidification velocities and thermal gradients on the order of those expected in AM melt pools, to investigate grain shape development across ranges of input parameters governing temperature field evolution, nucleation, and growth. Variation in nucleated grain shape from columnar to equiaxed as a function of thermal gradient and nucleation density is modeled with CA and verified against the established transition model of Hunt and Gaumann. Furthermore, while thermal conditions and nucleation density are shown to have the largest roles on microstructure development, the sensitivity of grain structure was very unevenly distributed across parameter space. In particular, it was found that microstructure is very sensitive to mean nucleation undercooling and the interfacial response function in process space regimes near grain structure transitions, but entirely controlled by a combination of thermal gradient, solidification velocity, and nucleation density away from such transitions. The understanding of grain shape sensitivity obtained through CA modeling, particularly at large thermal gradient and nucleation density, will be necessary for accurate microstructure prediction during the extreme processing conditions and large input parameter uncertainty common to AM.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multi deep learning-based stochastic microstructure reconstruction and high-fidelity micromechanics simulation of time-dependent ceramic matrix composite response

A multi deep learning-based framework is developed for efficient, automated microstructure reconstruction and generation of stochastic representative volume elements (SRVEs) with periodic boundary conditions (PBCs) for accurate modeling of ceramic matrix composite (CMC) response. The methodology comprises a convolutional neural network coupled with regression layers to act as a vanilla regression network for semantic segmentation of the microstructure, allowing accurate characterization of the phases and their distributions at the microscale. Scanning electron microscope and confocal microscope are used to obtain C/SiNC and SiC/SiNC CMCs micrographs for vanilla regression testing. Microstructure variability in terms of fiber volume fraction and porosity are quantified through the output regression layer, ensuring accurate representation of material variability in SRVE construction. Generative adversarial network (GAN) and its variants are designed to produce high-fidelity SRVE, spanning CMCs microstructure variability space. A circular padding algorithm is developed to generate SRVEs with PBCs during training of GANs. The accuracy of the generated SRVEs is established through micromechanics simulations, where an efficient formulation of the high-fidelity generalized methods of cells (HFGMC) approach is used to compute the effective mechanical properties. Furthermore, an iterative algorithm is implemented in the HFGMC solver to simulate time-dependent deformation of SiC/SiNC subjected to creep loading conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ synchrotron diffraction and modeling of non-equilibrium solidification of a MnFeCoNiCu alloy

The solidification mechanism and segregation behavior of laser-melted Mn 35 Fe 5 Co 20 Ni 20 Cu 20 was firstly investigated via in situ synchrotron x-ray diffraction at millisecond temporal resolution. The transient composition evolution of the random solid solution during sequential solidification of dendritic and interdendritic regions complicates the analysis of synchrotron diffraction data via any single conventional tool, such as Rietveld refinement. Therefore, a novel approach combining a hard-sphere approximation model, thermodynamic simulation, thermal expansion measurement and microstructural characterization was developed to assist in a fundamental understanding of the evolution of local composition, lattice parameter, and dendrite volume fraction corresponding to the diffraction data. This methodology yields self-consistent results across different methods. Via this approach, four distinct stages were identified, including: (I) FCC dendrite solidification, (II) solidification of FCC interdendritic region, (III) solid-state interdiffusion and (IV) final cooling with marginal diffusion. It was found out that in Stage I, Cu and Mn were rejected into liquid as Mn 35 Fe 5 Co 20 Ni 20 Cu 20 solidified dendritically. During Stage II, the lattice parameter disparity between dendrite and interdendritic region escalated as Cu and Mn continued segregating into the interdendritic region. After complete solidification, during Stage III, the lattice parameter disparity gradually decreases, demonstrating a degree of composition homogenization. The volume fraction of dendrites slightly grew from 58.3 to 65.5%, based on the evolving composition profile across a dendrite/interdendritic interface in diffusion calculations. Postmortem metallography further confirmed that dendrites have a volume fraction of 64.7 ± 5.3% in the final microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Origin of dislocation structures in an additively manufactured austenitic stainless steel 316L

In this experiment, the origin of dislocation structures in AM stainless steels was systematically investigated by controlling the effect of thermal stress through geometric constraints for the first time. Stainless steel 316L parts were produced in the form of “1D” rods, “2D” walls, and "3D" rectangular prisms to evaluate the effect of constraints to thermal expansion/shrinkage on the development of defect microstructures and to elucidate the origin of additively manufactured (AM) dislocation microstructures. Dislocation density, organization, chemical micro-segregation, precipitate structures, and misorientations were analyzed as a function of increasing constraints around solidifying material in 1D, 2D, and 3D components built using both directed energy deposition (DED) and powder-bed selective laser melting (SLM). In DED parts, the dislocation density was not dependent on local misorientations or micro-segregation patterns, but evolved from approximately ρ ⊥ = 10 12 m -2 in 1D parts to ρ ⊥ = 10 14 m -2 in 3D parts, indicating that it is primarily thermal distortions that produce AM dislocation structures. In DED 3D parts and SLM parts, dislocation densities were highest (ρ ⊥ ≈ 10 14 m -2 ) and corresponded to the formation of dislocation cells approximately 300-450 nm in diameter. Dislocation cells overlapped with dendrite micro-segregation in some but not all cases. The results illustrate that dendritic micro-segregation, precipitates, or local misorientations influence how the dislocations organize during processing, but are not responsible for producing the organized cell structures. Furthermore, this work shows that AM dislocation structures originate due to thermal distortions during printing, which are primarily dictated by constraints surrounding the melt pool and thermal cycling.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Fracture behavior of irradiation induced nanocrystalline UO 2 studied by in-situ mechanical testing in transmission electron microscopy

Uranium Dioxide (UO 2 ) is widely used as a fuel in current light water reactors (LWRs). Upon accumulation of radiation damage, LWR UO 2 fuel pellets start to develop a different microstructure at the pellet periphery when fuel burnup exceeds 45–50 GWd/tHM. The resulting porous, nanocrystalline microstructure is one of the most prominent microstructural changes occurring in such fuel. Its fracture mechanisms, which causes fuel fine fragmentation, could impact safety limits when the cladding breaches. Direct measurements of these properties are challenging, therefore a surrogate obtained via ion irradiation can be used. In this study, multiple microcantilevers were fabricated by focused ion beam from both fresh UO 2 and UO 2 irradiated with 84 MeV Xe 26+ ions to a peak dose of 1357 displacements per atom (dpa). Further, the irradiation produced a pseudo high burnup structure approximately 2 µm below the surface. In-situ nano-mechanical bending tests were conducted to investigate the fracture behavior and the effect of the surrogate UO 2 high burnup structure on local fracture properties. Fresh UO 2 fuel was observed to fracture in transgranular mode without nucleation or movement of dislocations. However, the Xe-irradiated nanocrystalline microcantilevers fractured along the grain boundaries, with no influence from the pre-existing micro-cracks in the microcantilever. Fracture toughness for this type of surrogate high burnup UO 2 structure is reported for the first time in literature. Both the fracture stress and toughness show degradation for UO 2 as a result of Xe-irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructure homogenization of concrete used in nuclear power plants

Almost all nuclear power plants in the United States are operating past their intended lifetimes or are requesting lifetime extensions. Therefore, understanding changes to the concrete containment structure over time is crucial to evaluate the structure’s continued viability. Concrete materials are heterogeneous particulate composites that exhibit viscoelastic material properties, which can lead to slow deformation over time, causing stress redistribution and the potential for creep cracking. A code to generate random, three dimensional (3D) concrete microstructures has been developed and paired with finite element analysis to predict the long-term viscoelastic properties of concrete. Data from these simulations are used to develop constitutive equations for the viscoelastic behavior of the homogenized concrete. The codes in this work are used to virtualize laboratory experiments, to obtain long-term creep data in a faster, cheaper manner. To validate this work, the simulated creep behavior of concrete is compared to 800 d of experimental data that has been extended to 27 y of data using the Time-Temperature superposition (TTS) principal. Excellent agreement between the simulation results and experimental data is seen.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Conversion of real-world aluminum scrap streams into high-performance Al–Mg–Si–Cu automotive alloys using shear assisted processing and extrusion

The conversion of post-consumer aluminum (Al) scrap into usable Al alloys without adding primary Al is challenging because of excess impurities. In this work, >99% post-consumer Twitch, used beverage cans (UBCs), and remelt scrap ingots (RSIs) were used as feedstock materials. As-cast and solution heat-treated feedstock billets were extruded using Shear Assisted Processing and Extrusion (ShAPE) at ~510°C, followed by press quenching. To explore the development of the microstructure, texture, and underlying mechanisms and how they contribute to the overall strengthening in as-extruded and artificially aged samples, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) were used to collect microstructure and texture data. The enhanced strength and ductility were corroborated with the microstructural features and crystallographic texture. Simple shear $\textrm{A}/\bar{\textrm{A}}$, $\textrm{A}_1^*/\textrm{A} _2^*$ texture components along with weak $\textrm{C}$ and $\textrm{B}/\bar{\textrm{B}}$ texture components were formed during extrusion; the texture was strengthened after heat treatment. The refined second-phase particles helped to retain the deformed microstructure and texture. The contributions of dislocation and precipitate strengthening were maximized when billets were solution-heat-treated prior to extrusion. This is attributed to the formation of effective supersaturated solid solutions during the ShAPE process, which precipitate out during the peak age treatment. Overall, the highest yield strength of 305 MPa, ultimate tensile strength of 350 MPa, and elongation of 12% were achieved in artificially aged samples, which are comparable to those of Al 6082-T6.

Al alloy↗
DOE OSTI2026

Impact of Porous Transport Layer Morphology on the Performance of Proton Exchange Membrane Water Electrolyzers with Ultra-Low Iridium Loadings

Reducing Ir loadings in proton exchange membrane water electrolyzer anodes is critical for lowering capital expenses. Loading reduction could be achieved by improving the Ir activity via doping/alloying and/or the development of advanced microstructures. However, the anode porous transport layer (PTL) is a comparatively simple component whose properties also impact Ir utilization. Therefore, well-designed PTLs may also enable reduced Ir loadings. In this work, we survey eight PTLs from various manufacturers to observe their impact on cell performance at low (0.4 mg Ir cm -2 ) and ultralow (0.1 mg Ir cm -2 ) Ir loadings. The PTLs were characterized by their microstructural properties, including porosity, particle size distribution, and pore size distribution. Electrochemical cell performance was correlated to PTL morphology, and it was found that PTLs with lower porosities and smaller particle and pore radii enabled good performance even at ultralow Ir loadings. 1000-h durability testing indicated that using lower porosity PTLs can significantly improve durability behavior. A runaway voltage phenomenon was observed during durability testing of cells with ultralow Ir loadings, which was caused by increases in both anode and cathode overpotentials. Furthermore, we observed that the beginning of test performance of 0.1 mg Ir cm -2 cells correlates to the 1000-h degradation rates of 0.4 mg Ir cm -2 cells, suggesting that for the Ir catalyst used in this work, short-term testing at ultralow loadings can be used as an indicator of long-term degradation at higher loadings.

08 HYDROGEN↗
DOE OSTI2026

Crossover as Determinant for Safety and Performance Tradeoffs in Proton Exchange Membrane Water Electrolyzers

Hydrogen (H2) crossover is a pressing challenge constraining safe and efficient operation of proton exchange membrane water electrolyzers (PEMWEs) especially amongst strides to employ thinner membranes, which enables improved energy efficiency, and elevated cathode pressures, that reduces the energy burden on downstream compressors. Here, we develop a microstructure-aware multicomponent reactive-transport framework that resolves dissolved and gaseous H2 transport pathways and mechanistically links electrode architecture to crossover related safety and performance. We show that operability is co-governed by the cathode catalyst layer (CCL) and the anode porous transport layer (APTL) which sets the H2 crossover flux and the egress capacity respectively. Elevated Pt/C ratio in the CCL suppresses crossover flux by up to 23% while a higher APTL porosity lowers H2 in O2 fraction by 0.6% in the anode effluent. We condense the findings into (cathode pressure-current density) maps overlaid with safety limits and performance targets and ultimately define two safety-performance unified metrics to gauge the size and quality of the operating window. Given the push towards higher pressure and deeper turndown for renewable integration, this study provides mechanistic design guidance to prevent crossover-induced safety risks while preserving the desired performance.

Electrolysis↗
DOE OSTI2021

Characterization of the strain-rate–dependent mechanical response of single cell–cell junctions

Cell–cell junctions are essential components in multicellular structures and often experience strains of different magnitudes and rates. However, their mechanical behavior is currently underexplored due to the lack of techniques to quantitatively characterize junctional stress–strain relationships. Here we developed a polymeric microstructure to strain the mutual junction of a single cell pair while simultaneously recording the junction stress and observed previously unseen strain-rate–dependent junction responses. We showed that cytoskeleton growth could relax the stress buildup and prevent junction failure at low strain rates, while high strain rates led to synchronized junction failures at remarkably large strains (over 200%). We expect this platform and our biophysical understanding to form the foundation for the rate-dependent mechanics of cell–cell junctions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Computational prediction of dielectric breakdown strength of a transformer paper in oil with uncertainty quantification

The determination of the dielectric breakdown strengths of microstructurally heterogeneous materials has been a primarily experimental endeavor. We report the development of a microstructure-level model for computationally predicting the breakdown strength and analyzing the interactions between electromagnetic pulses (EMP) and the constituents in a composite of cellulose-based paper and mineral oil found in electrical transformers. The model allows explicit simulation of the material breakdown process by tracking the transition of dielectric constituents from non-conductive to conductive states. The focus is on the electric fields induced in the materials and the overall conditions for dielectric breakdown (defined as the onset of avalanche) caused by the electric field induced in the composite. Responses to three distinct pulse shapes, i.e., Steep Front (SF), Lightning (L), and AC with spectra spanning 60–9 × 105 Hz are considered. It is found that the breakdown strength of the material is significantly affected by microstructure heterogeneities, the spatial variations of the constituent properties, and the pulse shapes. A probabilistic characterization of the breakdown strength is computationally obtained and compared with experimental measurements. Although one particular material is analyzed, the model and approach are applicable to other heterogeneous materials as well.

breakdowns↗
DOE OSTI2022

A crystal plasticity finite element method modeling of Zircaloy with hydride phases based on scanning electron micrographs

This work developed a microstructure-based finite element model to predict the stress state of alloys with second phase inclusions. Quantitative microstructural details extracted from scanning electron microscopy (SEM) images were used to generate heterogeneous microstructures including the morphology and spatial distribution of hydrides. Generation of digital microstructure was achieved through two steps of tessellations using software Neper and Matlab. The process is demonstrated using an example of Zircaloy material with secondary phases of hydrides dispersed within and stress-strain response of Zircaloy containing hydrides was predicted. The constitutive material model for Zircaloy in this study was based on crystal plasticity theory which considers the hexagonal close-packed (HCP) atomic structure of Zircaloy material. The hydrides were modeled as isotropic elasto-plastic material. A parametric study had been conducted to understand the effect of volume fraction, and lamellae thickness of the hydride phase on the mechanical properties of the overall material. Results can help designers to alter the manufacturing process to obtain the enhanced mechanical properties for components used in nuclear applications made by Zircaloy material.

Kulkarni, Shank S.↗
DOE OSTI2023

An ICME Modeling Framework for Titanium/Tungsten-Carbide Metal Matrix Composites

This report describes a collaborative project to develop a validated, predictive model for the high temperature mechanical properties of a titanium-matrix, tungsten-carbide/cobalt-reinforced metal matrix composite. The modeling approach was to first develop a detailed, microstructural model linking the material structure and the interfacial debonding properties to the effective properties of the material. The project then completed a throughput simulation campaign to generate a large number of simulations for discrete microstructures and different debonding parameters. Finally, the project trained a fast, Gaussian process surrogate model against this simulation database to provide a quick model linking the material compositions, structure, and processing parameters to the resulting material properties. This model was validated against high temperature tensile test data on a few particular composite compositions. The tests validate the model predictions for ultimate tensile strength and uniform elongation/ductility, meaning the final surrogate model can now be used to tune the material composition and processing parameters to identify optimal composite compositions for particular applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Through-Thickness Microstructure Characterization in a Centrifugally Cast Austenitic Stainless Steel Nuclear Reactor Primary Loop Pipe Using Time-of-Flight Neutron Diffraction

The US code of Federal Regulations mandates regular inspection of centrifugally cast austenitic stainless steel pipe, commonly used in primary cooling loops in light-water nuclear power plants. These pipes typically have a wall thickness of ~8 cm. Unfortunately, inspection using conventional ultrasonic techniques is not reliable as the microstructure strongly attenuates ultrasonic waves. Work is ongoing to simulate the behavior of acoustic waves in this microstructure and ultimately develop an acoustic inspection method for reactor inspections. In order to account for elastic anisotropy in the material, the texture in the steel was measured as a function of radial distance though the pipe wall. Experiments were conducted on two 10 × 12.7 × 80 mm radial sections of a cast pipe using neutron diffraction scans of 2 mm slices using the HIPPO time-of-flight neutron diffractometer at the Los Alamos Neutron Science Center (LANSCE, Los Alamos, NM, USA). Strong textures dominated by a small number of austenite grains with their (100) direction aligned in the radial direction of the pipe were observed. ODF analysis indicated that up to 70% of the probed volume was occupied by just three single-grain orientations, consistent with grain sizes of almost 1 cm. Texture and phase fraction of both ferrite and austenite phases were measured along the length of the samples. These results will inform the development of a more robust diagnostic tool for regular inspection of this material.

42 ENGINEERING↗