Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Phase field modeling of discontinuous dynamic recrystallization in hot deformation of magnesium alloys

We have developed a quantitative phase field model of discontinuous dynamic recrystallization (PF-DDRX) for investigating grain structure evolution and its impact on mechanical response in magnesium alloy during hot deformation. A set of isothermal compression tests were conducted by Gleeble thermo-mechanical simulator and used to determine PF-DDRX model parameters such as critical stresses of recrystallization, activation energies of dislocation, grain boundaries and recrystallization grain nucleation. In the simulations, the experimentally measured average grain size and distribution were used to generate initial microstructures. The results show that the typical ‘necklace’ microstructures observed in DDRX forms at the earlier stage of recrystallization. The inhomogeneity of microstructures first increases rapidly and then decreases gradually and reaches a constant with the increase of dynamic recrystallization volume fraction. Both predicted grain structure and mechanical response are in good agreement with experimental results. This demonstrates that the model parameters determined by experimental data are reliable for the developed PF-DDRX model to predict the grain structure evolution and flow behavior of AZ80 magnesium alloy under hot deformation. This work presents a path to combine experiments and modeling to give quantitative prediction and minimize experimental cost.

magnesium alloy, Phase field method, dynamic recry↗

Intracellular Dynamics of Superparamagnetic Iron Oxide Nanoparticles for Magnetic Partical Imaging

Superparamagnetic iron oxide nanoparticles (SPIONs) are a foundational platform for a variety of biomedical applications. Of particular interest is Magnetic Particle Imaging (MPI), which is a growing area of research and development due to its advantages including high resolution and sensitivity with positive contrast. There has been signicant work in the area of in vivo optimization of SPIONs for MPI as well as their biodistribution in and clearance from the body. However, little is known about the dynamics of SPIONs following cellular internalization which may limit their usefulness in a variety of potential imaging and treatment applications. This work shows a clear 20% decrease in magnetic performance of SPIONs, as observed by Magnetic Particle Spectroscopy (MPS), after internalization and systematic consideration of applicable factors that aect SPION signal generation, including microstructure, environment, and interparticle interactions. There is no observed change to SPION microstructure after internalization, and the surrounding environment plays little to no role in magnetic response for the SPIONs studied here. Interparticle interactions described by dipole-dipole coupling of SPIONs held close to one another after internalization are shown to be the dominant cause of decreased magnetic performance in cells. These conclusions were drawn from transmission electron microscopy (TEM) image analysis at relevant length scales, experimentally prepared and characterized SPIONs in varied environmental conditions, and theoretical modeling with Monte Carlo simulations.

Teeman, Eric M.↗

Radiation effects on materials for electrochemical energy storage systems

Batteries and electrochemical capacitors (ECs) are of critical importance for applications such as electric vehicles, electric grids, and mobile devices. However, the performance of existing battery and EC technologies falls short of meeting the requirements of high energy/high power and long durability for increasing markets such as the automotive industry, aerospace, and grid-storage utilizing renewable energies. Therefore, improving energy storage materials performance metrics is imperative. In the past two decades, radiation has emerged as a new means to modify functionalities in energy storage materials. There exists a common misconception that radiation with energetic ions and electrons will always cause radiation damage to target materials, which might potentially prevent its applications in electrochemical energy storage systems. But in this review, we summarize recent progress in radiation effects on materials for electrochemical energy storage systems to show that radiation can have both beneficial and detrimental effects on various types of energy materials. Prior work suggests that fundamental understanding toward the energy loss mechanisms that govern the resulting microstructure, defect generation, interfacial properties, mechanical properties, and eventual electrochemical properties is critical. Here, we discuss radiation effects in the following categories: (1) defect engineering, (2) interface engineering, (3) radiation-induced degradation, and (4) radiation-assisted synthesis. We analyze the significant trends and provide our perspectives and outlook on current research and future directions in research seeking to harness radiation as a method for enhancing the synthesis and performance of battery materials.

25 ENERGY STORAGE↗

Method for computationally efficient design of dielectric laser accelerator structures

Here, dielectric microstructures have generated much interest in recent years as a means of accelerating charged particles when powered by solid state lasers. The acceleration gradient (or particle energy gain per unit length) is an important figure of merit. To design structures with high acceleration gradients, we explore the adjoint variable method, a highly efficient technique used to compute the sensitivity of an objective with respect to a large number of parameters. With this formalism, the sensitivity of the acceleration gradient of a dielectric structure with respect to its entire spatial permittivity distribution is calculated by the use of only two full-field electromagnetic simulations, the original and ‘adjoint’. The adjoint simulation corresponds physically to the reciprocal situation of a point charge moving through the accelerator gap and radiating. Using this formalism, we perform numerical optimizations aimed at maximizing acceleration gradients, which generate fabricable structures of greatly improved performance in comparison to previously examined geometries.

43 PARTICLE ACCELERATORS↗

Generation and Characterization of Anisotropic Microstructures in Rare Earth-Iron-Boron Alloys

The goal of this work is to investigate methods in which anisotropy could be induced in fine-grained alloys. We have identified two general processing routes to creating a fine, textured microstructure: form an amorphous precursor and devitrify in a manner that induces texture or form the fine, textured microstructure upon cooling directly from the liquid state. Since it is possible to form significant amounts of amorphous material in RE-Fe-B alloys, texture could be induced through biasing the orientationof the crystallites upon crystallization of the amorphous material. One method of creating this bias is to form glassy material and apply uniaxial pressure during crystallization. Experiments on this are presented. All of the work presented here utilizes melt-spinning, either to create precursor material, or to achieve a desired final microstructure. To obtain greater control of the system to process these materials, a study was done on the effects of heating the wheel and modifying the wheel’s surface finish on glass formation and phase selection. The second general approach—creating the desired microstructure directly from the liquid—can be done through directional rapid solidification. In particular, alloys melt-spun at low tangential wheel speeds often display directional columnar growth through a portion of the ribbon. By refining and stabilizing the columnar growth, a highly textured fine microstructure is achieved. The effects of adding a segregating element (Ag) on the columnar growth are characterized and presented.

36 MATERIALS SCIENCE↗

3D RoboMET Characterization

The goal of this project is to generate 3D microstructural data by destructive and non-destructive means and provide accompanying characterization and quantitative analysis of such data. This work is a continuing part of a larger effort to relate material performance variability to microstructural variability. That larger effort is called “Predicting Performance Margins” or PPM. In conjunction with that overarching initiative, the RoboMET.3D™ is a specific asset of Center 1800 and is an automated serialsectioning system for destructive analysis of microstructure, which is called upon to provide direct customer support to 1800 and non-1800 customers. To that end, data collection, 3d reconstruction and analysis of typical and atypical microstructures have been pursued for the purposes of qualitative and quantitative characterization with a goal toward linking microstructural defects and/or microstructural features with mechanical response. Material systems examined in FY15 include precipitation hardened 17-4 steel, laser-welds of 304L stainless steel, thermal spray coatings of 304L and geological samples of sandstone.

Madison, Jonathan D.↗

Quarterly Management Document – FY17, 3rd Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications

Progress on modeling the the creep of thick sections welds in Alloy 740H is reported. Climb of dislocations during creep has been added to the model. Creep testing is continuing and stress drop testing has been initiated to determine the threshold stress of this particle-strengthened alloy. Work has also begun on generating synthetic microstructures, representative of experimental microstructures, from data collected with EBSD. This will enable incorporation of experimental microstructures into the modeling and simulation effort.

36 MATERIALS SCIENCE↗

Damage Accumulations Predictions for Boiler Components Via Microstructurally Informed Material Models

The goal of the project was to model material behavior and degradation during cyclic plasticity— with and without hold time—for nickel-based superalloys used in USC (ultra-super-critical) and A-USC (advanced-ultra-super-critical) boiler components. The study provided physically informed models, capturing the microstructural changes taking place in the industrial components under cyclic loading and long duration stress (up to 300,000 hours) and high temperature exposure (1100°F/593°C to 1400°F/760°C). The major developments were: 1) Qualitative and quantitative understanding of microstructure evolution (gamma prime precipitates), deformation (dislocation density), and damage mechanisms of Haynes ® 282 alloy. 2) Qualitative understanding of microstructural features generating local strain variations. 3) A continuum damage mechanics model (CDM) for Haynes ® 282 alloy at 1100°F to 1400°F capturing cyclic behavior with and without hold time. 4) Structural analysis for creep and LCF life predictions of an USC thick-wall Grade 91 superheater steel header and understanding life sensitivity to wall thickness of an AUSC Haynes ® 282 header.

20 FOSSIL-FUELED POWER PLANTS↗

Dynamics of the microstructure of current channels and the generation of high-energy electrons in nanosecond discharges in air

The results of the three-dimensional numerical simulation of the dynamics of the microstructure of high-voltage nanosecond discharges in air at atmospheric pressure are presented. It is established that the fast (at a time of ≈10 ns) broadening and significant decrease in the gas concentration in the microchannels occur as a result of the ohmic heating of microchannels with the diameter of 1–30 μm. It was shown that the broadening of microchannels in a nanosecond diffusive discharge provides an increase in the ratio of the electric field strength to the gas concentration in microchannels to values sufficient for the generation highenergy electron beams and X-ray bremsstrahlung in them. Features of the dynamics of the system of microchannels and its effect on the efficiency of the generation of high-energy electrons in discharges developing in the microstructuring regime of the current channels are considered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interplay between microstructure, defect states, and mobile charge generation in transition metal dichalcogenide heterojunctions

Two-dimensional transition metal dichalcogenides (2D-TMDCs) have gained attention for their promise in next-generation energy-harvesting and quantum computing technologies, but realizing these technologies requires a greater understanding of TMDC properties that influence their photophysics. To this end, we discuss here the interplay between TMDC microstructure and defects with the charge generation yield, lifetime, and mobility. As a model system, we compare monolayer-only and monolayer-rich MoS 2 grown by chemical vapor deposition, and we employ the TMDCs in Type-II charge-separating heterojunctions with semiconducting single-walled carbon nanotubes (s-SWCNTs). Our results suggest longer lifetimes and higher yields of mobile carriers in samples containing a small fraction of defect-rich multilayer islands on predominately monolayer MoS 2 . Compared to the monolayer-only heterojunctions, the carrier lifetimes increase from 0.73 μs to 4.71 μs, the hole transfer yield increases from 23% to 34%, and the electron transfer yield increases from 39% to 59%. We reach these conclusions using a unique combination of microwave photoconductivity (which probes only mobile carriers) along with transient absorption spectroscopy (which identifies spectral signatures unique to each material and type of photoexcited quasiparticle, but does not probe mobility). Overall, our results highlight the substantial changes in photophysics that can occur from small changes in TMDC microstructure and defect density, where the presence of defects does not necessarily preclude improvements in charge generation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Physically constrained 3D diffusion for inverse design of fiber-reinforced polymer composite materials

Designing fiber-reinforced polymer composites (FRPCs) with a tailored nonlinear stress-strain response is crucial for applications such as energy absorption in crash structures, flexible robotics, and impact-resistant protective gear. However, the inherent complexities of composite materials and the multitude of parameters involved, render traditional design and optimization methods inadequate for achieving effective inverse design of composites. In this paper, we present an AI-based inverse design framework that effectively and efficiently generates FRPCs with targeted nonlinear stress-strain responses. We introduce a physically constrained diffusion model (PC3D_Diffusion) capable of managing the complexities of composite materials and producing detailed, high-quality designs. We propose a loss-guided, learning-free approach to generate physically feasible microstructure designs by explicitly enforcing physical constraints during the generation process. For training purposes, 1.35 million FRPC samples were created, and their corresponding stress-strain curves were computed using established physics-based computational models. The results show that PC3D_Diffusion consistently generates high-quality designs with tailored mechanical behaviors, while guaranteeing compliance with the physical constraints. PC3D_Diffusion advances FRPC inverse design and may facilitate the inverse design of other 3D materials, offering potential applications in industries reliant on materials with custom mechanical properties.

Xu, Pei [Clemson Univ., SC (United States)]↗

Microscopy modality transfer of steel microstructures: Inferring scanning electron micrographs from optical microscopy using generative AI

Scanning electron microscopy (SEM) is resource intensive, which limits its throughput in some applications. As an alternative, we propose applying computer vision and machine learning to generate high-quality synthetic SEM micrographs from micrographs obtained using light optical microscopy (LOM). Working with a correlated LOM/SEM dataset of dual-phase steel images, we test generative models of various architectures, including encoder-decoder networks, generative adversarial networks (GANs), and diffusion-based models. We find that the diffusion models significantly outperform other methods on both qualitative and quantitative assessments, while preserving key metallurgical meaning. This work establishes diffusion as the state-of-the-art for microscopy modality transfer and demonstrates the potential of AI-powered microscopy to enhance LOM with micron scale structural recreation.

Computer vision↗

Microstructure Scale Lithium-Ion Battery Modeling: Part I. On Through-Plane Heterogeneity, Impact of Mesh Representation, and Differences between Macro- and Microscale Models

Li-ion battery performance and degradation are strongly correlated with the electrode microstructures and can be modeled at different scales, each with their own limitations. Herein, we compare predictions achieved with a macro- and a micro-scale model, that is, respectively, neglecting or considering the microstructural heterogeneity of the composite electrodes, on virtual numerically generated and real microstructures. While both models are in relative agreement at the low charge rates, differences arise for fast charging scenarios and especially for the real, highly heterogenous, microstructures. The microscale model predicts that electrolyte concentration saturation and depletion, respectively, at the back of the cathode and of the anode are exacerbated, and that lithium plating occurs earlier for real microstructures. The present work also indicates that the mesh representation significantly impacts the microscale model predictions, and consequently that microscale models should add surface area as a parameter to consider explicitly surface roughness. This article is the first of a series, with subsequent entries further investigating in-plane heterogeneities, lithium plating, and the impact of microstructure representativity on model predictions.

25 ENERGY STORAGE↗

Discovering mechanisms for materials microstructure optimization via reinforcement learning of a generative model

Abstract The design of materials structure for optimizing functional properties and potentially, the discovery of novel behaviors is a keystone problem in materials science. In many cases microstructural models underpinning materials functionality are available and well understood. However, optimization of average properties via microstructural engineering often leads to combinatorically intractable problems. Here, we explore the use of the reinforcement learning (RL) for microstructure optimization targeting the discovery of the physical mechanisms behind enhanced functionalities. We illustrate that RL can provide insights into the mechanisms driving properties of interest in a 2D discrete Landau ferroelectrics simulator. Intriguingly, we find that non-trivial phenomena emerge if the rewards are assigned to favor physically impossible tasks, which we illustrate through rewarding RL agents to rotate polarization vectors to energetically unfavorable positions. We further find that strategies to induce polarization curl can be non-intuitive, based on analysis of learned agent policies. This study suggests that RL is a promising machine learning method for material design optimization tasks, and for better understanding the dynamics of microstructural simulations.

36 MATERIALS SCIENCE↗

Engineering Two-Phase and Three-Phase Microstructures from Water-Based Dispersions of Nanoparticles for Eco-Friendly Polymer Solar Cell Applications

Nanoparticle organic photovoltaics, a subfield of organic photovoltaics (OPV), has attracted increasing interest in recent years due to the eco-friendly fabrication of solar modules afforded by colloidal ink technology. Importantly, using this approach it is now possible to engineer the microstructure of the light absorbing/charge generating layer of organic photovoltaics; decoupling film morphology from film deposition. In this study, single-component nanoparticles of poly(3-hexylthiophene) (P3HT) and phenyl-C 61 butyric acid methyl ester (PC 61 BM) were synthesized and used to generate a two-phase microstructure with control over domain size prior to film deposition. Scanning transmission X-ray microscopy (STXM) and electron microscopy were used to characterize the thin film morphology. Uniquely, the measured microstructure was a direct input for a nanoscopic kinetic Monte Carlo (KMC) model allowing us to assess exciton transport properties that are experimentally inaccessible in these single-component particles. Photoluminescence, UV-vis spectroscopy measurements, and KMC results of the nanoparticle thin films enabled the calculation of an experimental exciton dissociation efficiency (η ED ) of 37% for the two-phase microstructure. The glass transition temperature (T g ) of the materials was characterized with dynamic mechanical thermal analysis (DMTA) and thermal annealing led to an increase in ηED to 64% due to an increase in donor-acceptor interfaces in the thin film from both sintering of neighboring opposite-type particles in addition to the generation of a third mixed phase from diffusion of PC 61 BM into amorphous P3HT domains. Finally, this study demonstrates the higher level of control over donor-acceptor film morphology enabled by customizing nanoparticulate colloidal inks, where the optimal three-phase film morphology for an OPV photoactive layer can be designed and engineered.

36 MATERIALS SCIENCE↗

Simulated effect of defect volume and location on very high cycle fatigue of laser beam powder bed fused AlSi10Mg

This study quantifies the interaction between volumetric defect location and size on the very high cycle fatigue (VHCF) of laser beam powder bed fused (LB-PBF) AlSi10Mg. Crystal plasticity finite element method (CPFEM) simulations were used to investigate the effects of defect location and size on the driving force for crack initiation. The CPFEM model was calibrated against uniaxial and cyclic experimental data of LB-PBF AlSi10Mg. Defect characteristics were informed by experimental data from the specimens produced in various geometries to create realistic representative volume elements (RVEs) with equivalent volume fractions of defects. By embedding defects of varying sizes and locations within the RVEs, fatigue indicator parameters (FIPs) were calculated to analyze the impact of defects’ characteristics on fatigue performance. Different combinations of defect volume and locations were generated for various microstructure instantiations, providing insight into extreme value fatigue responses. Larger defect volumes located on free surfaces consistently generated the highest FIPs, suggesting defect size and boundary proximity intensify stress concentration effects. RVEs with multiple smaller defects produced lower FIPs than those with single large critical defects. These findings underscore the critical role of defect characteristics on fatigue life, providing a foundation for future predictive modeling in fatigue-sensitive AM applications.

AlSi10Mg↗

Multi deep learning-based stochastic microstructure reconstruction and high-fidelity micromechanics simulation of time-dependent ceramic matrix composite response

A multi deep learning-based framework is developed for efficient, automated microstructure reconstruction and generation of stochastic representative volume elements (SRVEs) with periodic boundary conditions (PBCs) for accurate modeling of ceramic matrix composite (CMC) response. The methodology comprises a convolutional neural network coupled with regression layers to act as a vanilla regression network for semantic segmentation of the microstructure, allowing accurate characterization of the phases and their distributions at the microscale. Scanning electron microscope and confocal microscope are used to obtain C/SiNC and SiC/SiNC CMCs micrographs for vanilla regression testing. Microstructure variability in terms of fiber volume fraction and porosity are quantified through the output regression layer, ensuring accurate representation of material variability in SRVE construction. Generative adversarial network (GAN) and its variants are designed to produce high-fidelity SRVE, spanning CMCs microstructure variability space. A circular padding algorithm is developed to generate SRVEs with PBCs during training of GANs. The accuracy of the generated SRVEs is established through micromechanics simulations, where an efficient formulation of the high-fidelity generalized methods of cells (HFGMC) approach is used to compute the effective mechanical properties. Furthermore, an iterative algorithm is implemented in the HFGMC solver to simulate time-dependent deformation of SiC/SiNC subjected to creep loading conditions.

36 MATERIALS SCIENCE↗