Search NASA⌕ Search

SEARCH · Search NASA

Results for “molybdenum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Electrotransport and diffusivity of molybdenum, rhenium, tungsten, and zirconium in beta-thorium

The electric mobilities, diffusivities, and effective valences were determined for molybdenum, rhenium, tungsten, and zirconium in beta-thorium. All four solutes migrated in the same direction as the electron flow. Rhenium and molybdenum were found to be very mobile, with tungsten somewhat slower. Zirconium was found to move at a rate near that of the self-diffusion of beta-thorium, viz., about 10 to the -11th sq m/s at 1500 C. The electromigration velocities showed a similar trend. A comparison was made between experimental data obtained by scanning laser mass spectrometry and theoretical transport equations for two purification experiments. Good agreement was obtained with both the concentration profile predicted by DeGroot and the purification ratio predicted by Verhoeven.

Schmidt, F. A.↗
NASA NTRS1985

Molybdenum-silicon multilayer mirrors for the extreme ultraviolet

Multilayer structures of molybdenum and silicon have been synthesized by sputter deposition onto flat silicon single-crystal silicon substrates and spherically ground (0.5and 22.0-m radii) fused silica substrates; and the reflectivities for 170.4-A (72.8-eV), 160.1-A (77.4-eV), and 228-A (54.4-eV) light measured at near normal incidence. Observed peak values ranged from 26.2 to 78 percent, the highest reflectivities occurring closest to normal incidence. Energy resolutions were about 10 in all cases. Model calculations were performed using optical constants and experimentally determined multilayer structural parameters. In all cases the measured reflectivities were equal to or larger (by up to a factor of 2) than the calculated values, a result attributed to uncertainty in the optical constants used in the calculations. Experimental and calculated angular-peak positions and energy resolutions were in good agreement. The high reflectivities of these molybdenum-silicon structures will make possible application of traditional optics approaches in the EUV and support new developments including free-electron lasers.

Barbee, T. W., Jr.↗
NASA NTRS1986

Voltammetric studies of porous molybdenum electrodes for the alkali metal thermoelectric converter

Voltammetry of partially oxidized porous molybdenum alkali metal thermoelectric converter (AMTEC) electrodes from about 600 to 1000 K revealed a series of redox processes within the AMTEC operational voltage range which can be used to establish the electronic and ionic conductivities of these electrodes. Improved estimates of the free energies of formation of Na2Mo3O6, NaMoO2, and Na3MoO4 are obtained. Evidence is provided for the slow corrosive attack by Na2MoO4 on molybdenum. The ionic conductivity of Na2MoO4 is found to be sufficiently large at temperatures of greater than 700 K to explain the observed electrochemical phenomena in addition to the enhanced sodium transport in AMTEC electrodes below the freezing point of Na2MoO4.

Williams, R. M.↗
NASA NTRS1990

Secondary electron emission characteristics of molybdenum-masked, ion-textured OFHC copper

A method for producing a uniform, highly textured surface on oxygen-free, high conductivity (OFHC) copper by ion bombardment using sputtered molybdenum as a texture-inducing masking film was developed and used to provide samples for study. The purpose was to develop a basically OFHC copper surface having very low secondary electron emission characteristics. Surfaces having low secondary electron emission are a requirement for the electrodes of very high efficiency multistage depressed collectors (MDC's). Such MDC's are used in microwave amplifier traveling wave tubes for space communications and other applications. OFHC copper is the material most commonly used for MDC electrodes because it has high thermal conductivity, it is easy to machine, and its fabrication and brazing procedures are well established. However, its untreated surface displays relatively very high levels of secondary electron emissions. Textured OFHC copper samples were tested for true secondary electron emission and relative reflected primary electron yield at primary electron beam energy levels from 200 to 2000 eV and at direct (0 deg) to oblique (60 deg) beam impingement angles. The test results for three of the samples, each of which was processed in a slightly different way, are compared with each other and with test results for a machined OFHC copper sample. Although the textured samples are not represented here as having been processed optimally, their measured secondary electron emission characteristics are significantly lower than those of the untreated OFHC copper sample over the range of conditions studied. Importantly, the relative reflected primary electron yield of one of the textured samples is conspicuously lower than that of the others. Clearly, with further development, the molybdenum-masked ion-textured OFHC copper surface will be a promising material for high-efficiency MDC electrodes.

Curren, Arthur N.↗
NASA NTRS1991

Investigation of welding and brazing of molybdenum and TZM alloy tubes

This effort involved investigating the welding and brazing techniques of molybdenum tubes to be used as cartridges in the crystal growth cartridge. Information is given in the form of charts and photomicrographs. It was found that the recrystallization temperature of molybdenum can be increased by alloying it with 0.5 percent titanium and 0.1 percent zirconium. Recrystallization temperatures for this alloy, known as TZM, become significant around 2500 F. A series of microhardness tests were run on samples of virgin and heat soaked TZM. The test results are given in tabular form. It was concluded that powder metallurgy TZM may be an acceptable cartridge material.

Lundblad, Wayne E.↗
NASA NTRS1992

Molybdenum In Cathodes Of Sodium/Metal Chloride Cells

Cyclic voltammetric curves of molybdenum wire in NaAlCl4 melt indicate molybdenum chloride useful as cathode material in rechargeable sodium/metal chloride electrochemical cells. Batteries used in electric vehicles, for electric-power load leveling, and other applications involving high energy and power densities.

Bugga, Ratnakumar V.↗
NASA NTRS1951

Study of Chromium-Frit-Type Coatings for High-Temperature Protection of Molybdenum

The achievement of more compact and efficient power plants for aircraft is dependent, among other factors, on the perfection of heat-resisting materials that are superior to those in current use. Molybdenum is one of the high-melting metals (melting point, 4750 F). It is fairly abundant and also can be worked into many of the shapes required in modern power plants. To permit its widespread use at elevated temperatures, however, some means must first be found to prevent its rapid oxidation. The application of a protective coating is one method that might be used to achieve this goal. In the present work, a number of chromium-frit-type coatings were studied. These were bonded to molybdenum specimens by firing in controlled atmospheres to temperatures in the range of 2400 to 2700 F.

CERAMICS↗
NASA NTRS1930

Methods for the Identification of Aircraft Tubing of Plain Carbon Steel and Chromium-Molybdenum Steel

The survey of the possibilities for distinguishing between plain carbon and chromium-molybdenum steel tubing included the Herbert pendulum hardness, magnetic, sparks, and chemical tests. The Herbert pendulum test has the disadvantages of all hardness tests in being limited to factory use and being applicable only to scale-free, normalized material. The small difference in the range of hardness values between plain carbon and chromium-molybdenum steels is likewise a disadvantage. The Rockwell hardness test, at present used in the industry for this purpose, is much more reliable. It may be concluded on the basis of the experiments performed that of all methods surveyed, spark testing appears to be, at present, the most suitable for factory use from the standpoint of speed, accuracy, nondestructiveness and reliability. It is also applicable for field use.

Mutchler, W H↗
NASA NTRS1932

Rapid chemical test for the identification of chromium-molybdenum steel

This note describes a simple, rapid, qualitative test which can be applied to solutions of drilling or chips for the identification of chromium-molybdenum steel. The test is based on the orange-red compound which is formed when thiocyanate and inequivalent molybdenum react. This test is much more reliable than the potassium ethylxanthate test which has been recommended for a like purpose. A list of the apparatus and reagents which are required, and a description of the procedure follows.

Redmond, John C↗
NASA NTRS1953

Effect of Prestraining of Recrystallization Temperature and Mechanical Properties of Commercial, Sintered, Wrought Molybdenum

Given three presumably identical lots of commercial, sintered, wrought molybdenum, the 1-hour recrystallization temperature of one lot remained above 2900 F by limiting the amount of effective restraining to 35 percent or less. Different recrystallization temperatures were obtained in various atmospheres, the highest in argon and the lowest in hydrogen. Metal thus fabricated and then stress-relieved possessed an ultimate tensile strength at room temperature within 10 percent of metal swaged 99 percent and also possessed equivalent ductility. At 1800 F, equivalent strength and ductility was obtained irrespective of the amount of swaging over the range of 10 to 99 percent. The amount of swaging greatly influenced the recrystallized grain size but the difference in grain size is not the major controlling factor which determines whether recrystallized molybdenum is ductile or brittle at room temperature.

MATERIALS, PROPERTIES - TENSILE↗
NASA NTRS1952

Oxidation-resistance Mechanism and Other Properties of Molybdenum Disilicide

The outstanding oxidation resistance of molybdenum disilicide at 2400 F and above was found to depend on the formation of a protective siliceous coating which a-cristobalie has been identified. Molybdenum disilicide is not inherently resistant to oxidation and in powdered form burns at low temperatures.Melting and casting experiments have demonstrated the decomposition of the material at the melting point. The room-temperature modulus of elasticity has been determined and electric-resistivity data are given to 2000 F.

MATERIALS, PROPERTIES-CORROSION RESISTANCE↗
NASA NTRS1995

Reactive melt infiltration of silicon-molybdenum alloys into microporous carbon preforms

Investigations on the reactive melt infiltration of silicon-1.7 and 3.2 at.% molybdenum alloys into microporous carbon preforms have been carried out by modeling, differential thermal analysis (DTA), and melt infiltration experiments. These results indicate that the pore volume fraction of the carbon preform is a very important parameter in determining the final composition of the reaction-formed silicon carbide and the secondary phases. Various undesirable melt infiltration results, e.g. choking-off, specimen cracking, silicon veins, and lake formation, and their correlation with inadequate preform properties are presented. The liquid silicon-carbon reaction exotherm temperatures are influenced by the pore and carbon particle size of the preform and the compositions of infiltrants. Room temperature flexural strength and fracture toughness of materials made by the silicon-3.2 at.% molybdenum alloy infiltration of medium pore size preforms are also discussed.

Singh, M.↗
NASA NTRS1960

Investigation of Problems Associated with the Use of Alloyed Molybdenum Sheet in Structures at Elevated Temperatures

The results of an experimental study to explore the capabilities and limitations of thin Mo-0.5Ti molybdenum-alloy sheet for structural applications at high temperatures are presented. Evaluation tests at temperatures ranging from room temperature,to 3000 F were made on resistance-welded corrugated-core sandwiches that were coated with a commercially available oxidation resistant coating known as W-2 and on coated oxidation and tensile specimens. The performance of the corrugated-core sandwiches in compressive strength and static oxidation tests, tensile properties of the coated molybdenum sheet, and the life of the coated specimens in static oxidation tests are given. A description of the equipment and procedures utilized in performing the evaluation tests is included.

Mathauser, Eldon E.↗
NASA NTRS1961

Investigation of Oxidation-Resistant Coatings on Graphite and Molybdenum in Two Arc-Powered Facilities

A number of leading-edge specimens of ATJ graphite and 0.5-percent titanium-molybdenum alloy were tested in a 6-inch subsonic low-pressure arc-powered tunnel and a 1,500-kw subsonic arc jet to determine the effectiveness of several refractory coatings in preventing the oxidation of these materials. The results indicate that the siliconized coating for the ATJ graphite and the W-2 and Durak MG coatings for the titanium-molybdenum alloy provide adequate protection at temperatures up to 3,000 F for the durations of the tests in these facilities, approximately 70 seconds in the arc tunnel and approximately 10 minutes in the arc jet. Weight losses (less than one-half of 1 percent) experienced by a few of the coated specimens indicate that tests of longer duration in these environments may prove deleterious and that the stability of these coatings may be depreciated under the low-pressure environmental conditions encountered during reentry.

Peters, Roger W.↗
NASA NTRS2016

Electron-Beam Deposition of Superconducting Molybdenum Thin Films for the Development of Mo/Au TES X-Ray Microcalorimeter

We are exploring the properties of electron-beam evaporated molybdenum thin films on silicon nitride coated silicon wafers at substrate temperatures between room temperature and 650 C. The temperature dependence of film stress, transition temperature, and electrical properties are presented. X-ray diffraction measurements are performed to gain information on molybdenum crystallite size and growth. Results show the dominant influence of the crystallite size on the intrinsic properties of our films. Wafer-scale uniformity, wafer yield, and optimal thermal bias regime for TES fabrication are discussed.

Microcalorimeter↗
DOE OSTI2023

Completion of Critical Experiments with Molybdenum Sleeves at Sandia

Sandia National Laboratories (SNL) and the Institut de Radioprotection et de Sûreté Nucléaire (IRSN) have collaborated on the design and execution of a set of critical experiments that explore the effects of molybdenum in water moderated fuel-rod arrays. The molybdenum is included as sleeves (tubes) on some of the fuel rods in the arrays. The fuel used in the experiments is known at Sandia as the Seven Percent Critical Experiment (7uPCX) fuel. This fuel has been used is several published benchmark evaluations in including LEU-COMP-THERM-78 and LEU-COMP THERM-080.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Molybdenum Carbide Electrocatalyst In Situ Embedded in Porous Nitrogen–Rich Carbon Nanotubes Promotes Rapid Kinetics in Sodium–Metal–Sulfur Batteries

This work is the first report of a molybdenum carbide-based electrocatalyst for sulfur-based sodium metal batteries (SMBs/NMBs). MoC/Mo 2 C is in-situ grown on nitrogen-doped carbon nanotubes in parallel with formation of extensive nanoporosity. Sulfur impregnation (50 wt% S) results in unique triphasic architecture termed MoC/Mo 2 C@PCNT-S. Quasi-solid-state phase transformation to Na 2 S is promoted in carbonate electrolyte, with in-situ time-resolved Raman, XPS and optical analysis demonstrating minimal soluble polysulfides. MoC/Mo 2 C@PCNT-S cathodes delivered among the most promising rate performance characteristics in literature, achieving 987 mAh g -1 at 1 Ag -1 , 818 mAh g -1 at 3 A g -1 , and 621 mAh g -1 at 5 A g -1 . The cells deliver superior cycling stability, retaining 650 mAh g -1 after 1000 cycles at 1.5 Ag -1 , corresponding to 0.028% capacity decay per cycle. High mass loading cathodes (64 wt% S, 12.7 mg cm -2 ) also show cycling stability, with anode degradation due to deep plating/stripping driving capacity decay. Density functional theory (DFT) demonstrates that formation energy of Na 2 S x (1 ≤ x ≤ 4) on surface of MoC/Mo 2 C is significantly lowered compared to analogous redox in liquid. Strong binding of Na 2 S x (1 ≤ x ≤ 4) on MoC/Mo 2 C surfaces results from charge transfer between the sulfur and Mo sites on carbides' surface.

25 ENERGY STORAGE↗