Results for “navigation processing” — Page 7

NASA NTRS2010

Preliminary Design of the Guidance, Navigation, and Control System of the Altair Lunar Lander

Guidance, Navigation, and Control (GN&C) is the measurement and control of spacecraft position, velocity, and attitude in support of mission objectives. This paper provides an overview of a preliminary design of the GN&C system of the Lunar Lander Altair. Key functions performed by the GN&C system in various mission phases will first be described. A set of placeholder GN&C sensors that is needed to support these functions is next described. To meet Crew safety requirements, there must be high degrees of redundancy in the selected sensor configuration. Two sets of thrusters, one on the Ascent Module (AM) and the other on the Descent Module (DM), will be used by the GN&C system. The DM thrusters will be used, among other purposes, to perform course correction burns during the Trans-lunar Coast. The AM thrusters will be used, among other purposes, to perform precise angular and translational controls of the ascent module in order to dock the ascent module with Orion. Navigation is the process of measurement and control of the spacecraft's "state" (both the position and velocity vectors of the spacecraft). Tracking data from the Earth-Based Ground System (tracking antennas) as well as data from onboard optical sensors will be used to estimate the vehicle state. A driving navigation requirement is to land Altair on the Moon with a landing accuracy that is better than 1 km (radial 95%). Preliminary performance of the Altair GN&C design, relative to this and other navigation requirements, will be given. Guidance is the onboard process that uses the estimated state vector, crew inputs, and pre-computed reference trajectories to guide both the rotational and the translational motions of the spacecraft during powered flight phases. Design objectives of reference trajectories for various mission phases vary. For example, the reference trajectory for the descent "approach" phase (the last 3-4 minutes before touchdown) will sacrifice fuel utilization efficiency in order to provide landing site visibility for both the crew and the terrain hazard detection sensor system. One output of Guidance is the steering angle commands sent to the 2 degree-of-freedom (dof) gimbal actuation system of the descent engine. The engine gimbal actuation system is controlled by a Thrust Vector Control algorithm that is designed taking into account the large quantities of sloshing liquids in tanks mounted on Altair. In this early design phase of Altair, the GN&C system is described only briefly in this paper and the emphasis is on the GN&C architecture (that is still evolving). Multiple companion papers will provide details that are related to navigation, optical navigation, guidance, fuel sloshing, rendezvous and docking, machine-pilot interactions, and others. The similarities and differences of GN&C designs for Lunar and Mars landers are briefly compared.

Lee, Allan Y.↗

NASA NTRS2005

Hardware in-the-Loop Demonstration of Real-Time Orbit Determination in High Earth Orbits

This paper presents results from a study conducted at Goddard Space Flight Center (GSFC) to assess the real-time orbit determination accuracy of GPS-based navigation in a number of different high Earth orbital regimes. Measurements collected from a GPS receiver (connected to a GPS radio frequency (RF) signal simulator) were processed in a navigation filter in real-time, and resulting errors in the estimated states were assessed. For the most challenging orbit simulated, a 12 hour Molniya orbit with an apogee of approximately 39,000 km, mean total position and velocity errors were approximately 7 meters and 3 mm/s respectively. The study also makes direct comparisons between the results from the above hardware in-the-loop tests and results obtained by processing GPS measurements generated from software simulations. Care was taken to use the same models and assumptions in the generation of both the real-time and software simulated measurements, in order that the real-time data could be used to help validate the assumptions and models used in the software simulations. The study makes use of the unique capabilities of the Formation Flying Test Bed at GSFC, which provides a capability to interface with different GPS receivers and to produce real-time, filtered orbit solutions even when less than four satellites are visible. The result is a powerful tool for assessing onboard navigation performance in a wide range of orbital regimes, and a test-bed for developing software and procedures for use in real spacecraft applications.

Moreau, Michael↗

NASA NTRS1988

A model of electronic map interpretation

This paper describes an experiment that provides data for the development of a cognitive model of pilot flight navigation. The model views navigation as a process involving the alignment of mental images with the perceptual view out of the cockpit. The data support a three stage model: (1) the perceptual encoding of the map display, (2) mental rotation of the mental image, and (3) comparison of the image to the environment. The variables that significantly influence the processes embodied in the model in decreasing importance are: speed of processing, display sequencing, map complexity, and rotation angle of the map. The model can be used as a preliminary computational tool in predicting the navigational component of pilot situational awareness.

Aretz, Anthony J.↗

NASA NTRSDate not supplied

Multi-Functional Flash Lidar for Precision Safe Landing in Challenging Terrains

A Flash Lidar utilizing a novel Super-Resolution (SR) technique has been developed for providing Terrain Relative Navigation and Hazard Avoidance capabilities onboard landing vehicles. Processing algorithms for precision navigation and safe landing location identification take advantage of the uniform fixed pixels property of generated high resolution Digital Elevation Maps (DEMs) to achieve high reliability operation in near real-time. This paper describes the current and next generation breadboard units, report the results of recent dynamic tests, and explain the operational concept as envisioned for future landing missions.

3-D Imaging↗

NASA NTRSDate not supplied

Multi-Functional Flash Lidar for Precision Safe Landing in Challenging Terrains

A Flash Lidar utilizing a novel Super-Resolution (SR) technique has been developed for providing Terrain Relative Navigation and Hazard Avoidance capabilities onboard landing vehicles. Processing algorithms for precision navigation and safe landing location identification take advantage of the uniform fixed pixels property of generated high resolution Digital Elevation Maps (DEMs) to achieve high reliability operation in near real-time. This paper describes the current and next generation breadboard units, report the results of recent dynamic tests, and explain the operational concept as envisioned for future landing missions.

3-D Imaging↗

NASA NTRSDate not supplied

Development of Flash Lidar Sensor for Precision Safe Landing

A Flash Lidar utilizing a novel Super-Resolution (SR) technique has been developed for providing Terrain Relative Navigation and Hazard Avoidance capabilities onboard landing vehicles. Processing algorithms for precision navigation and safe landing location identification take advantage of the uniform fixed pixels property of generated high resolution Digital Elevation Maps (DEMs) to achieve high reliability operation in near real-time. This paper describes the current and next generation breadboard units, report the results of recent dynamic tests, and explain the operational concept as envisioned for future landing missions.

3-D Imaging↗

NASA NTRSDate not supplied

Development of a Compact Lidar Sensor for Terrain Relative Navigation and Terrain Hazard Avoidance

A Lidar sensor utilizing linear-mode flash lidar technology and a novel Super-Resolution technique has been developed for providing Terrain Relative Navigation and Hazard Avoidance capabilities onboard landing vehicles. Processing algorithms for precision navigation and safe landing location identification take advantage of the uniform fixed pixels property of generated high resolution Digital Elevation Maps to achieve high reliability operation in near real-time. This paper describes the results of drone and helicopter flight tests of a breadboard system, explains the design and capabilities of a recently built compact prototype unit, and proposes a concepts of operation for future landing missions.

3-D Imaging↗

NASA NTRSDate not supplied

Development of a Compact Lidar Sensor for Terrain Relative Navigation and Terrain Hazard Avoidance

A Flash Lidar utilizing a novel Super-Resolution (SR) technique has been developed for providing Terrain Relative Navigation and Hazard Avoidance capabilities onboard landing vehicles. Processing algorithms for precision navigation and safe landing location identification take advantage of the uniform fixed pixels property of generated high resolution Digital Elevation Maps (DEMs) to achieve high reliability operation in near real-time. This paper describes the current and next generation breadboard units, report the results of recent dynamic tests, and explain the operational concept as envisioned for future landing missions.

3-D Imaging↗

NASA NTRSDate not supplied

High Resolution Terrain Sensing Lidar for Precision Navigation and Safe Landing of Space and Aerial Vehicles

A Flash Lidar utilizing a novel Super-Resolution (SR) technique has been developed for providing Terrain Relative Navigation and Hazard Avoidance capabilities onboard landing vehicles. Processing algorithms for precision navigation and safe landing location identification take advantage of the uniform fixed pixels property of generated high resolution Digital Elevation Maps (DEMs) to achieve high reliability operation in near real-time. This paper describes the current and next generation breadboard units, report the results of recent dynamic tests, and explain the operational concept as envisioned for future landing missions.

Precision Landing↗

NASA NTRS1976

A microcomputer-based low-cost Omega navigation system

The application of a low cost, commercially available microcomputer as the navigation processor for a simplified OMEGA navigation system is an area of current research. The interface of a low cost front end OMEGA sensor is described and an example of the phase processing software and navigation routines is given. Emphasis is placed on the description of results obtained with the software version of the OMEGA burst filter known as the memory aided phase locked loop.

Lilley, R. W.↗

NASA NTRS1999

Testing of the International Space Station and X-38 Crew Return Vehicle GPS Receiver

This paper discusses the process and results of the performance testing of the GPS receiver planned for use on the International Space Station (ISS) and the X- 38CrewReturnVehicle(CRV). The receiver is a Force-19 unit manufactured by Trimble Navigation and modified in software by NASA:s Goddard Space Flight Center (GSFC) to perform navigation and attitude determination in space. The receiver is the primary source of navigation and attitude information for ISS and CRV. Engineers at GSFC have developed and tested the new receiver with a Global Simulation Systems Ltd (GSS) GPS Signal Generator (GPSSG). This paper documents the unique aspects of ground testing a GPS receiver that is designed for use in space. A discussion of the design of tests using the GPSSG, documentation, data capture, data analysis, and lessons learned will precede an overview of the performance of the new receiver. A description of the challenges that were overcome during this testing exercise will be presented. Results from testing show that the receiver will be within or near the specifications for ISS attitude and navigation performance. The process for verifying other requirements such as Time to First Fix, Time to First Attitude, selection/deselection of a specific GPS satellite vehicles (SV), minimum signal strength while still obtaining attitude and navigation, navigation and attitude output coverage, GPS week rollover, and Y2K requirements are also given in this paper.

Simpson, James↗

NASA NTRS1999

Testing of the International Space Station and X-38 Crew Return Vehicle GPS Receiver

This paper discusses the process and results of the performance testing of the GPS receiver planned for use on the International Space Station (ISS) and the X-38 Crew Return Vehicle (CRV). The receiver is a Force-19 unit manufactured by Trimble Navigation and Modified in software by the NASA Goddard Space Flight Center (GSFC) to perform navigation and attitude determination in space. The receiver is the primary source of navigation and attitude information for ISS and CRV. Engineers at GSFC have developed and tested the new receiver with a Global Simulation Systems Ltd (GSS) GPS Signal Generator (GPSSG). This paper documents the unique aspects of ground testing a GPS receiver that is designed for use in space. A discussion of the design and tests using the GPSSG, documentation, data capture, data analysis, and lessons learned will precede an overview of the performance of the new receiver. A description of the challenges of that were overcome during this testing exercise will be presented. Results from testing show that the receiver will be within or near the specifications for ISS attitude and navigation performance. The process for verifying other requirements such as Time to First Fix, Time to First Attitude, selection/deselection of a specific GPS satellite vehicles (SV), minimum signal strength while still obtaining attitude and navigation, navigation and attitude output coverage, GPS week rollover, and Y2K requirements are also given in this paper.

Simpson, James↗

NASA NTRS1999

Testing of the International Space Station and X-38 Crew Return Vehicle GPS Receiver

This paper discusses the process and results of the performance testing of the GPS receiver planned for use on the International Space Station (ISS) and the X-38 Crew Return Vehicle (CRV). The receiver is a Force-19 unit manufactured by Trimble Navigation and modified in software by the NASA Goddard Space Flight Center (GSFC) to perform navigation and attitude determination in space. The receiver is the primary source of navigation and attitude information for ISS and CRV. Engineers at GSFC have developed and tested the new receiver with a Global Simulation Systems Ltd (GSS) GPS Signal Generator (GPSSG). This paper documents the unique aspects of ground testing a GPS receiver that is designed for use in space. A discussion of the design of tests using the GPSSG, documentation, data capture, data analysis, and lessons learned will precede an overview of the performance of the new receiver. A description of the challenges that were overcome during this testing exercise will be presented. Results from testing show that the receiver will be within or near the specifications for ISS attitude and navigation performance. The process for verifying other requirements such as Time to First Fix, Time to First Attitude, selection/deselection of a specific GPS satellite vehicles (SV), minimum signal strength while still obtaining attitude and navigation, navigation and attitude output coverage, GPS week rollover, and Y2K requirements are also given in this paper.

Simpson, James↗

NASA NTRS2004

Mars Reconnaissance Orbiter Navigation

Mars Reconnaissance Orbiter will launch in August 2005 at Cape Canaveral Air Force Station. The heavyweight spacecraft will use a Lockheed-Martin Atlas V-401 launch vehicle. It will be the first mission in a low Mars Orbit to characterize the surface, subsurface, and atmospheric properties. The intensive science operation imposes a great challenge for Navigation to satisfy the stringent requirements. This paper describes navigation key requirements, major challenges, and the sophisticated dynamic modeling. It also details navigation strategy and processes for various mission phases. Mars Reconnaissance Orbiter will return significant amount of scientific data in support of the objectives set by the Mars Exploration Program. A robust and precise navigation is the key to the success of this mission.

navigation↗

NASA NTRS2018

SEXTANT X-Ray Pulsar Navigation Demonstration: Additional On-Orbit Results

The Station Explorer for X-ray Timing and Navigation Technology (SEXTANT) is a technology demonstration enhancement to the Neutron-star Interior Composition Explorer (NICER) mission, a NASA Astrophysics Explorer Mission of Opportunity to the International Space Station, launched in June of 2017. In late 2017, SEXTANT successfully completed a first demonstration of in-space and autonomous X-ray pulsar navigation (XNAV). This form of navigation relies on processing faint signals from millisecond pulsars-rapidly rotating neutron stars that appear to pulsate in the X-ray band-and could potentially provide a GPS-like navigation capability applicable throughout the solar-system and beyond. In this work, we briefly review prior SEXTANT results and then present new results focusing on: making use of the high- flux but rotationally unstable Crab pulsar, and using XNAV to estimate position, velocity, and time in the presence of an imperfect local clock.

Navigation↗

NASA NTRS1982

Space Shuttle Orbiter descent navigation

The entry operational sequence (OPS 3) begins approximately 2 hours prior to the deorbit maneuver and continues through atmospheric entry, terminal area energy management (TAEM), approach and landing, and rollout. During this flight phase, the navigation state vector is estimated by the Space Shuttle Orbiter onboard navigation system. This estimate is computed using a six-element sequential Kalman filter, which blends inertial measurement unit (IMU) delta-velocity data with external navaid data. The external navaids available to the filter are tactical air navigation (TACAN), barometric altimeter, and microwave scan beam landing system (MSBLS). Attention is given to the functional design of the Orbiter navigation system, the descent navigation sensors and measurement processing, predicted Kalman gains, correlation coefficients, and current flights navigation performance.

Montez, M. N.↗

NASA NTRS2009

Maneuver Automation Software

The Maneuver Automation Software (MAS) automates the process of generating commands for maneuvers to keep the spacecraft of the Cassini-Huygens mission on a predetermined prime mission trajectory. Before MAS became available, a team of approximately 10 members had to work about two weeks to design, test, and implement each maneuver in a process that involved running many maneuver-related application programs and then serially handing off data products to other parts of the team. MAS enables a three-member team to design, test, and implement a maneuver in about one-half hour after Navigation has process-tracking data. MAS accepts more than 60 parameters and 22 files as input directly from users. MAS consists of Practical Extraction and Reporting Language (PERL) scripts that link, sequence, and execute the maneuver- related application programs: "Pushing a single button" on a graphical user interface causes MAS to run navigation programs that design a maneuver; programs that create sequences of commands to execute the maneuver on the spacecraft; and a program that generates predictions about maneuver performance and generates reports and other files that enable users to quickly review and verify the maneuver design. MAS can also generate presentation materials, initiate electronic command request forms, and archive all data products for future reference.

Uffelman, Hal↗

NASA NTRS1994

Design and flight evaluation of an integrated navigation and near-terrain helicopter guidance system for night-time and adverse weather operations

NASA and the U.S. Army have designed, developed, and flight evaluated a Computer Aiding for Low Altitude Helicopter Flight (CALAHF) guidance system. This system provides guidance to the pilot for near terrain covert helicopter operations. It automates the processing of precision navigation information, helicopter mission requirements, and terrain flight guidance. The automation is presented to the pilot through symbology on a helmet-mounted display. The symbology is a 'pilot-centered' design which preserves pilot flexibility and authority over the CALAHF system's automation. An extensive flight evaluation of the system has been conducted using the U.S. Army's NUH-60 STAR (Systems Testbed for Avionics Research) research helicopter. The evaluations were flown over a multiwaypoint helicopter mission in rugged mountainous terrain, at terrain clearance altitudes from 300 to 125 ft and airspeeds from 40 to 110 knots. The results of these evaluations showed that the pilots could precisely follow the automation symbology while maintaining a high degree of situational awareness.

Swenson, Harry N.↗