SEARCH · Search NASA

Results for “nuclear level density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS2003

Brayton Power Conversion Unit Tested: Provides a Path to Future High-Power Electric Propulsion Missions

Closed-Brayton-cycle conversion technology has been identified as an excellent candidate for nuclear electric propulsion (NEP) power conversion systems. Advantages include high efficiency, long life, and high power density for power levels from about 10 kWe to 1 MWe, and beyond. An additional benefit for Brayton is the potential for the alternator to deliver very high voltage as required by the electric thrusters, minimizing the mass and power losses associated with the power management and distribution (PMAD). To accelerate Brayton technology development for NEP, the NASA Glenn Research Center is developing a low-power NEP power systems testbed that utilizes an existing 2- kWe Brayton power conversion unit (PCU) from previous solar dynamic technology efforts. The PCU includes a turboalternator, a recuperator, and a gas cooler connected by gas ducts. The rotating assembly is supported by gas foil bearings and consists of a turbine, a compressor, a thrust rotor, and an alternator on a single shaft. The alternator produces alternating-current power that is rectified to 120-V direct-current power by the PMAD unit. The NEP power systems testbed will be utilized to conduct future investigations of operational control methods, high-voltage PMAD, electric thruster interactions, and advanced heat rejection techniques. The PCU was tested in Glenn s Vacuum Facility 6. The Brayton PCU was modified from its original solar dynamic configuration by the removal of the heat receiver and retrofitting of the electrical resistance gas heater to simulate the thermal input of a steady-state nuclear source. Then, the Brayton PCU was installed in the 3-m test port of Vacuum Facility 6, as shown. A series of tests were performed between June and August of 2002 that resulted in a total PCU operational time of about 24 hr. An initial test sequence on June 17 determined that the reconfigured unit was fully operational. Ensuing tests provided the operational data needed to characterize PCU performance over its full operating range. The primary test variables used in operating the Brayton PCU were heater input power and rotor speed. Testing demonstrated a maximum steady-state alternating-current power output of 1835 W at a gas heater power of 9000 W and a rotor speed of 52000 rpm. The corresponding measured turbine inlet gas temperature was 1076 K, and the compressor inlet gas temperature was 282 K. When insulation losses from the gas heater were neglected, the Brayton cycle efficiency for the maximum power point was calculated to be 24 percent. The net direct-current power output was 1750 W, indicating a PMAD efficiency of about 95 percent.

Mason, Lee S.↗

DOE OSTI2022

Three-dimensional strain imaging of irradiated chromium using multi-reflection Bragg coherent diffraction

Abstract Radiation-induced materials degradation is a key concern in limiting the performance of nuclear materials. The formation of nanoscale void and gas bubble superlattices in metals and alloys under radiation environments can effectively mitigate radiation-induced damage, such as swelling and aid the development of next generation radiation tolerant materials. To effectively manage radiation-induced damage via superlattice formation, it is critical to understand the microstructural changes and strain induced by such superlattices. We utilize multi-reflection Bragg coherent diffraction imaging to quantify the full strain tensor induced by void superlattices in iron irradiated chromium substrate. Our approach provides a quantitative estimation of radiation-induced three-dimensional (3D) strain generated at the microscopic level and predicts the number density of defects with a high degree of sensitivity. Such quantitative evaluation of 3D strain in nuclear materials can have a major impact on predicting materials behavior in radiation environments and can revolutionize design of radiation tolerant materials.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Quantum Vibronic Effects on the Electronic Properties of Molecular Crystals

We present a study of molecular crystals, focused on the effect of nuclear quantum motion and anharmonicity on their electronic properties. We consider a system composed of relatively rigid molecules, a diamondoid crystal, and one composed of floppier molecules, NAI-DMAC, a thermally activated delayed fluorescence compound. We compute fundamental electronic gaps at the density functional theory (DFT) level of theory, with the Perdew–Burke–Erzenhof (PBE) and strongly constrained and approximately normed (SCAN) functionals, by coupling first-principles molecular dynamics with a nuclear quantum thermostat. We find a sizable zero-point renormalization (ZPR) of the band gaps, which is much larger in the case of diamondoids (0.6 eV) than for NAI-DMAC (0.22 eV). We show that the frozen phonon (FP) approximation, which neglects intermolecular anharmonic effects, leads to a large error (~50%) in the calculation of the band gap ZPR. Instead, when using a stochastic method, we obtain results in good agreement with those of our quantum simulations for the diamondoid crystal. However, the agreement is worse for NAI-DMAC where intramolecular anharmonicities contribute to the ZPR. Our results highlight the importance of accurately including nuclear and anharmonic quantum effects to predict the electronic properties of molecular crystals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Photo response of 164 Dy

Background: Little data is available for the pygmy dipole resonance (PDR) in axially deformed nuclei. Photon-scattering experiments are complicated by high level densities in the PDR region and the small energy difference of transitions to the ground state and to excited states. Purpose: In this work, we report on an experimental study of the low-energy dipole strength distribution of the well-deformed nucleus 164 Dy between 4.0–7.7 MeV. Methods: The low-lying photoresponse of 164 Dy has been investigated using the method of nuclear resonance fluorescence using a quasimonochromatic linearly polarized $\textit{γ}$-ray beam in the energy range of 4.0–7.7 MeV in steps of 0.2 MeV. Results: For excitation energies between 4 MeV and 5 MeV, sufficiently low level densities allow for the identification of individual states, including level energies, reduced transition widths and branching ratios. Energy-averaged mean decay branching ratios, mean population ratios and partial absorption cross sections were determined above 5 MeV up to the neutron-separation threshold at 7.7 MeV. A Lorentzian-shaped enhancement of the partial photo absorption cross section followed by decays back to the ground-state band is found at 6.10(5) MeV with a width of 0.77(23) MeV. A comparison with results from complementary measurements is performed using the framework of the statistical model. Conclusions: The experimental results for the mean population ratios deviate systematically from the statistical model simulation by 30(6)%. However, they are in agreement within one standard deviation of the simulation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2024

Dynamic and relativistic effects on Pt–Pt indirect spin–spin coupling in aqueous solution studied by ab initio molecular dynamics and two- vs four-component density functional NMR calculations

Treating 195Pt nuclear magnetic resonance parameters in solution remains a considerable challenge from a quantum chemistry point of view, requiring a high level of theory that simultaneously takes into account the relativistic effects, the dynamic treatment of the solvent–solute system, and the dynamic electron correlation. A combination of Car-Parrinello molecular dynamics (CPMD) and relativistic calculations based on two-component zeroth order regular approximation spin–orbit Kohn–Sham (2c-ZKS) and four-component Dirac–Kohn–Sham (4c-DKS) Hamiltonians is performed to address the solvent effect (water) on the conformational changes and JPtPt1 coupling. A series of bridged PtIII dinuclear complexes [L1–Pt2(NH3)4(Am)2–L2]n+ (Am = α–pyrrolidonate and pivalamidate; L = H2O, Cl−, and Br−) are studied. The computed Pt–Pt coupling is strongly dependent on the conformational dynamics of the complexes, which, in turn, is correlated with the trans influence among axial ligands and with the angle N–C–O from the bridging ligands. The J-coupling is decomposed in terms of dynamic contributions. The decomposition reveals that the vibrational and explicit solvation contributions reduce JPtPt1 of diaquo complexes (L1 = L2 = H2O) in comparison to the static gas-phase magnitude, whereas the implicit solvation and bulk contributions correspond to an increase in JPtPt1 in dihalo (L1 = L2 = X−) and aquahalo (L1 = H2O; L2 = X−) complexes. Relativistic treatment combined with CPMD shows that the 2c-ZKS Hamiltonian performs as well as 4c-DKS for the JPtPt1 coupling.

Chemistry↗

DOE OSTI2020

Shell structure of 43 S and collapse of the N = 28 shell closure

The single-particle structure of the N = 27 isotones provides insights into the shell evolution of neutron-rich nuclei from the doubly-magic 48 Ca toward the drip line. 43 S was studied employing the one-neutron knockout reaction from a radioactive 44 S beam. Using a combination of prompt and delayed γ-ray spectroscopy the level structure of 43 S was clarified. Momentum distributions were analyzed and allowed for spin and parity assignments. The deduced spectroscopic factors show that the 44 S ground-state configuration has a strong intruder component. Here, the results were confronted with shell model calculations using two effective interactions. General agreement was found between the calculations, but strong population of states originating from the removal of neutrons from the 2p 3/2 orbital in the experiment indicates that the breakdown of the N = 28 magic number is more rapid than the theoretical calculations suggest.

39 ≤ A ≤ 58↗

DOE OSTI2022

Nuclear states projected from a pair condensate

Atomic nuclei exhibit deformation, pairing correlations, and rotational symmetries. To meet these competing demands in a computationally tractable formalism, we revisit the use of general pair condensates with good particle number as a trial wave function for even-even nuclei. After minimizing the energy of the condensate, allowing for general triaxial deformations, we project out states with good angular momentum with a fast projection technique. To show applicability, we present example calculations from pair condensates in several model spaces and compare against angular-momentum projected Hartree-Fock and full configuration-interaction shell-model calculations. This approach successfully generates spherical, vibrational, and rotational spectra, demonstrating potential for modeling medium- to heavy-mass nuclei.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Bayesian model mixing with multireference energy density functional

Reliably predicting nuclear properties across the entire chart of isotopes is important for applications ranging from nuclear astrophysics to superheavy science to nuclear technology. To this day, however, all the theoretical models that can scale at the level of the chart of isotopes remain semiphenomenological. Because they are fitted locally, their predictive power can vary significantly; different versions of the same theory provide different predictions. Bayesian model mixing takes advantage of such imperfect models to build a local mixture of a set of models to make improved predictions. Earlier attempts to use Bayesian model mixing for mass table calculations relied on models treated at single-reference energy density functional level, which fail to capture some of the correlations caused by configuration mixing or the restoration of broken symmetries. In this study we have applied Bayesian model mixing techniques within a multireference energy density functional (MR-EDF) framework. We considered predictions of two-particle separation energies from particle number projection or angular momentum projection with four different energy density functionals—a total of eight different MR-EDF models. We used a hierarchical Bayesian stacking framework with a Dirichlet prior distribution over weights together with an inverse log-ratio transform to enable positive correlations between different models. We found that Bayesian model mixing provides significantly improved predictions compared to the participating models. Published by the American Physical Society 2025

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS1979

The MPD thruster development program

Recent research results have inferred that the self-field magnetoplasmadynamic (MPD) thruster can attain efficiency and specific impulse levels which are competitive with ion thrusters. Based on these results, a program was initiated at JPL to develop this thruster for application on future spacecraft. Preliminary mission analyses have shown that the high thrust density MPD arcjet is advantageous for high power missions, such as a short trip time earth orbit transfer vehicle or a nuclear powered outer planet explorer. Direct thrust stand verification of the inferred performance levels used in these analyses is planned for a facility being assembled at Princeton University. A parallel effort at JPL is considering various thruster system configurations, energy storage concepts and propellant control techniques. In addition, a one pulse per second thruster test facility is planned at JPL to be used for thruster optimization studies including erosion and lifetime measurements.

Rudolph, L. K.↗

DOE OSTI2020

An Improved Model For Determining Salinity Recharge Time for Deep Borehole Disposal - 20405

In a previous publication (K. P. Travis, D. Burley and F. G. F. Gibb, WM2017 Conference, Phoenix Arizona paper no. 17480) we introduced a numerical model to estimate the time it would take for a pressure perturbation to subside following its creation from the construction of a deep geological borehole in water-saturated rock. The model was based on the notion of a point source of momentum - a solution of the time-dependent pressure-diffusion equation. Using the model, we estimated that it would take on the order of 10 k years for physical equilibrium to become re-established following the sinking of a 5 km borehole in granite. The significance of such a model is that it places an upper bound on the lifetime required of a borehole sealing system - a necessary input to a borehole post-closure safety case assessment. No engineered sealing system has ever been devised which is capable of retaining its sealing properties for 10 half-lives of long-lived radioisotopes in spent fuel or high-level waste. One of the key advantages of disposing of nuclear waste via Deep Borehole Disposal (DBD) is the natural sealing provided by density stratified groundwater. Upon sinking of a borehole, and subsequent filling with fresh water, brine or drilling mud, this natural barrier may be temporarily damaged. Over time, fresh brine from the far-field will flow towards or away from the hole (driven by a pressure gradient) and will eventually re-establish the original salinity gradient. It follows that the engineered seals need last only as long as the time required for this salinity gradient to reset itself. One of the limitations of our previous model was the use of a static boundary condition on the borehole wall. The model used a boundary pressure which varied quadratically with depth (arising from differences between the pressure of a column of fresh water in the borehole and that of a column of brine in the host rock). However as brine replaces fresh water in the borehole (driven by a pressure gradient), the boundary function must change with time. We now introduce an improved model which takes this time dependent boundary condition into account. The model also takes into account the time taken for a mixture of brine and fresh water to re-establish chemical equilibrium through the process of diffusion. The paper contains the mathematical details of our new iterative model as well as results showing the time taken to reach steady state, and concentration profiles for the components of the brine-filled borehole as a function of time together with a discussion on the implications of the results for developing a post-closure safety assessment for DBD. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2024

Bubbler Design Updates for Nuclear Safeguards Applications

The accurate monitoring of molten salt is crucial for nuclear safeguards, particularly in the context of mixtures used in molten salt reactors and pyropocessing. To attain material accountancy in actinide bearing molten salts, fluid volume and density are needed. Previous work utilized a triple bubbler sensor to measure the fluid level and density in processing tanks. This triple bubbler system utilized three gas dip-tubes strategically positioned at different heights within the molten salt such that the molten salt level, density, and surface tension were determined simultaneously. This investigation explores the effectiveness of an updated bubbler design with larger internal diameters for the dip-tubes to reduce plugging. The findings of this study will provide valuable insights into a bubbler design and configuration for applications in nuclear safeguards. This will contribute to enhanced accountability and transparency in the monitoring of actinide bearing molten salts, promoting objectives in nuclear safeguards.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Bubbler Design Updates for Nuclear Safeguards Application

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Excitation energy partition in fission

Not Available

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2021

Levels in 125 Cd populated by the β decay of 125 m Ag and 125 Ag

Here, the β decay of 125 m, 125 Ag into levels in 125 Cd was investigated at the Holifield Radioactive Ion Beam Facility (HRIBF). Uranium-238 targets were bombarded with 50-MeV protons with an intensity of 15 μ A, and the induced fission products were mass separated and deposited on a moving tape in the center of the VANDLE array consisting of γ detectors and plastic scintillators. A partial decay scheme has been assigned for both β decay of the (9/2 + ) ground state of 125 Ag and its low-lying (1/2 - ) isomer, with the energy of the low-lying (11/2 - ) isomeric state in 125 Cd assigned as 188.5 keV. In addition, β -delayed neutron emission probabilities were also determined to be 1.2(2)% for the (9/2 + ) 125 Ag ground state and 4.6(10)% for the (1/2 - ) isomer, which are substantially lower than the previously reported value.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Discovery of the new isotope 251 Lr and the α-decay fine structure in 253 L

The products of the 203, 205 Tl ( 50 Ti, 2n) fusion-evaporation reactions were studied using the recently commissioned Argonne Gas-Filled Analyzer at Argonne National Laboratory. Two α-decay activities with energies of 9210(19) and 9246(19) keV and half-lives of $42^{+42}_{-14}$ and $24.4^{+7.0}_{-4.5}$ ms were observed which were followed by the known α decays of 247 Md and 243 Es . They are interpreted as originating from the 1/2 ⁻ [521] and 7/2 ⁻ [514] single-proton Nilsson states in the hitherto unknown isotope 251 Lr . From the measured Q α values the 1/2 ⁻ level was placed 117(27) keV above the 7/2 - level in 251 Lr in contrast to 255 Lr where the 1/2 ⁻ level is the lowest. Also, the α decay of 253 Lr was studied in more detail and a new α line at 8660(20) keV was found and a new half-life value of 2.46(32) s for an isomeric state in 253 Lr was measured. The 251, 253, 255 Lr Q α values were compared with predictions of various mass models. The relative energies of the 1/2 ⁻ [521] and 7/2 ⁻ [514] single-proton Nilsson states in 251, 253, 255 Lr isotopes were compared with results of the cranking shell model with pairing treated using the particle-number-conserving method. The level separation and, in particular, the level order change between 251 Lr and 255 Lr was reproduced only when the hexacontetrapole deformation ϵ 6 was included in the calculations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2023

Material Effects on Electron-Capture Decay in Cryogenic Sensors

Several current searches for physics beyond the standard model are based on measuring the electron-capture (EC) decay of radionuclides implanted into cryogenic high-resolution sensors. The sensitivity of these experiments has already reached the level where systematic effects related to atomic state energy changes from the host material are a limiting factor. One example is a neutrino mass study based on the nuclear EC decay of 7 Be to 7 Li inside cryogenic Ta-based sensors. Here, to understand the material effects at the required level, we use density-functional theory to model the electronic structure of lithium atoms in different atomic environments of the polycrystalline Ta absorber film. The calculations reveal that the Li 1s binding energies can vary by more than 2 eV due to insertion at different lattice sites, at grain boundaries, in disordered Ta, and in the vicinity of various impurities. However, the total range of Li 1s shifts does not exceed 4 eV, even for extreme amorphous disorder. Furthermore, when investigating the effects on the Li 2s levels, we find broadening of more than 5 eV due to hybridization with the Ta band structure. Material effects are shown to contribute significantly to peak broadening in Ta-based sensors that are used to search for physics beyond the standard model in the EC decay of 7 Be, but they do not explain the full extent of observed broadening. Understanding these in-medium effects will be required for current- and future-generation experiments that observe low-energy radiation from the EC decay of implanted isotopes to evaluate potential limitations on the measurement sensitivity.

36 MATERIALS SCIENCE↗

NASA NTRS2013

UltraSail CubeSat Solar Sail Flight Experiment

UltraSail is a next-generation, highrisk, high-payoff sail system for the launch, deployment, stabilization, and control of very large (km2 class) solar sails enabling high payload mass fractions for interplanetary and deep space spacecraft. UltraSail is a non-traditional approach to propulsion technology achieved by combining propulsion and control systems developed for formation- flying microsatellites with an innovative solar sail architecture to achieve controllable sail areas approaching 1 km2, sail subsystem area densities approaching 1 g/m2, and thrust levels many times those of ion thrusters used for comparable deep space missions. UltraSail can achieve outer planetary rendezvous, a deep-space capability now reserved for high-mass nuclear and chemical systems. There is a twofold rationale behind the UltraSail concept for advanced solar sail systems. The first is that sail-andboom systems are inherently size-limited. The boom mass must be kept small, and column buckling limits the boom length to a few hundred meters. By eliminating the boom, UltraSail not only offers larger sail area, but also lower areal density, allowing larger payloads and shorter mission transit times. The second rationale for UltraSail is that sail films present deployment handling difficulties as the film thickness approaches one micrometer. The square sail requires that the film be folded in two directions for launch, and similarly unfolded for deployment. The film is stressed at the intersection of two folds, and this stress varies inversely with the film thickness. This stress can cause the film to yield, forming a permanent crease, or worse, to perforate. By rolling the film as UltraSail does, creases are prevented. Because the film is so thin, the roll thickness is small. Dynamic structural analysis of UltraSail coupled with dynamic control analysis shows that the system can be designed to eliminate longitudinal torsional waves created while controlling the pitch of the blades, while using solar photon pressure to slew the spin axis. Vacuum tests have also verified that electrostatic and molecular adhesion forces can substantially be eliminated by making the film electrically conductive, reducing the peel force of the film off the storage roll to levels of 100s of micro-N. The innovation demonstrated the capability of deploying a six-micron aluminum- coated film from a reel through a slit in vacuum. The innovation also demonstrated a spin-stabilized method for deploying a long reel of solar sail film using solar pressure to spin-up and orbit raise the satellite, and also a gravity gradient method for deploying a long reel of solar sail film using solar pressure to orbit raise the satellite. The solar sail mass fraction of 25% is consistent with high specific impulse ion systems, but without the added weight and cost of a power source and processing unit. The large sail area, coupled with low film density, is giving UltraSail a high payload fraction. The UltraSail deployment scheme unrolls a micrometerscale reflection-coated polyimide film from a storage mandrel to a maximum length of several kilometers with the aid of a blade tip satellite.

Carroll, David↗

DOE OSTI2020

Development of a Testbed for Pipeline Flushing - 20425

Pipelines which carry high-level waste within the DOE complex should be properly flushed in the cases where stationary or moving beds of solid sediment occur, or lines are prone to hydrogen gas buildup. Present guidelines establish a minimum for the amount of water (flush volume) and flush velocity values used for post-transfer flushing operations to achieve satisfactory cleaning of pipelines. However, further studies are needed to find optimal operating velocity modes/values in order to minimizing the flush volume and consequent downstream waste. These efforts are significantly helpful to DOE waste remediation sites by preserving tank storage, preventing additional waste processing, and minimizing dilution and changes in waste chemistry. An experimental test loop was recently developed for study of non-Newtonian slurry flushing at the Florida International University (FIU). This loop was designed to create sediment beds of various materials and bed heights and investigate parameters that effect the efficiency of flushing operations. The objective is to find flush velocity values/modes which lead to satisfactory cleaning of transport lines with a minimum amount of water usage. A 165 ft experimental test loop made of 3-inch carbon steel pipes was constructed and used in initial testing campaigns. This pipe loop was equipped with real-time monitoring instruments to record variation of pressure, density, mass flow rate, and temperature during testing. Post-flush in-situ no-flow evaluations were performed using ultrasonic, endoscopy, and visual inspection. Additional post-flush evaluations were conducted using filtration and density monitoring of residuals within a designated circulations loop. These provisions enable comparison of pipeline cleanness before the start and after termination of flushing operations for efficiency evaluation. This paper presents efforts associated with flushing of kaolin-water mixtures at different concentrations and with various flush volume and flush velocity values/modes. In initial testing, efforts focused on creating repeatable sediment beds inside the pipeline in both fully-flooded (no pre-flush drainage) and gravity-drained (pre-flush drained) systems. Bed characterization (i.e., measurement of sediment height and solids concentration) was conducted to ensure about consistency of initial conditions between tests. Preliminary results for flushing study of 10% vol. kaolin-water mixtures starting from a fully-flooded initial condition showed that flushing with 1-line volume (65 gallons) could remove up to 72 percent of solids from the pipeline. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗