Search NASA⌕ Search

SEARCH · Search NASA

Results for “on-board processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Addressing the crush of sampling

An overall space information system involves sensing, processing, analyzing, and distributing space-acquired information. These systems may be partitioned into the spacecraft segment, the wideband space-to-ground communication segment, and the ground-based data analysis and distribution segment. The paper discusses NASA's advanced technology programs aimed at providing improved sensors and on-board data systems. Advances in charge-transfer devices, lasers, and microwave technologies will be responsible for major improvements in NASA's sensing and detection capabilities for future missions. These improvements will result in a future data crush that will amplify the data management problem.

Olstad, W. B.↗
NASA NTRS1987

Ram accelerator direct launch system for space cargo

The ram accelerator, a chemically-propelled mass driver, is presented as a new approach for directly launching acceleration-insensitive pay-loads into LEO. The cargo vehicle resembles the centerbody of a conventional ramjet and travels through a launch tube filled with a premixed gaseous fuel and oxidizer mixture. The tube acts as the outer cowling of the ramjet and the combustion process travels with the vehicle. Two modes of ram accelerator drive are described, which when used in sequence, are capable of accelerating the cargo vehicle to 10 km/sec. The requirements for placing a 2000 kg vehicle with 50 percent payload fraction into a 400 km orbit, with a minimum of on-board rocket propellant for circularization maneuvers, are examined. It is shown that aerodynamic heating during atmospheric transit results in very little ablation of the nose. Both direct and indirect orbital insertion scenarios are investigated, and a three-step maneuver consisting of two burns and aerobraking is found to minimize the on-board propellant mass. A scenario involving a parking orbit below the desired final orbit is suggested as a means to increase the flexibility of the mass launch concept.

Bruckner, A. P.↗
NASA NTRS1974

Science objectives and the Mariner Jupiter/Saturn 1977 mission design

The two Mariner spacecraft to be launched in 1977 to fly by Jupiter and Saturn require a mission design which is heavily dependent on science objectives. These science objectives translate into trajectory requirements imposed by one or more of the eleven instruments aboard Mariner such as distance of closest approach, inclination, occultation, lighting, etc., at the bodies of interest. Also, Jupiter and Saturn cannot be considered as individual targets but as miniature solar systems, where the mission design must apply to the Jovian and Saturnian satellites, and to Saturn's rings. The major objective of this analysis is to translate the science desires into the mission possibilities. Each object, be it a Galilean satellite, Titan, or the ring of Saturn, provides a unique region suitable for scientific investigation for the on-board instruments. Some of these trajectory regions overlap, others do not. Thus, critical choices must be made in selecting the trajectories to be flown by the two Mariner spacecraft. Such a choice, though preliminary, has been made by the Mariner Jupiter/Saturn 1977 (MJS'77) science teams, and a brief discussion of the selection process and the pair of trajectories chosen is presented in this paper.

Penzo, P. A.↗
NASA NTRS1985

Development and flight test of a helicopter, X-band, portable precision landing system concept

A beacon landing system (BLS) is being developed and flight tested as a part of NASA's Rotorcraft All-Weather Operations Research Program. The system is based on state-of-of-the-art X-band radar technology and digital processing techniques. The bLS airborne hardware consists of an X-band receiver and a small micropreocessor, installed in conjunction wht the aircraft instrument landing system (ILS) receiver. The microprocessor analyzes the X-band, BLS pulses and outputs ILS-compatible localizer and glide slope signals. Range information is obtained using an on-board weather/mapping radar in conjunction with the BLS. The ground station is an inexpensive, portable unit; it weighs less than 70 lb and can be quickly deployed at a landing site. Results from the flight-test program show that the BLS has a significant potential for providing rotorcaraft with low-cost, precision instrument approach capability in remote areas.

Davis, T. J.↗
NASA NTRS1984

An integrated voice and data multiple-access scheme for a land-mobile satellite system

An analytical study is performed of the satellite requirements for a land mobile satellite system (LMSS). The spacecraft (MSAT-X) would be in GEO and would be compatible with multiple access by mobile radios and antennas and fixed stations. The FCC has received a petition from NASA to reserve the 821-825 and 866-870 MHz frequencies for the LMSS, while communications with fixed earth stations would be in the Ku band. MSAT-X transponders would alter the frequencies of signal and do no processing in the original configuration considered. Channel use would be governed by an integrated demand-assigned, multiple access protocol, which would divide channels into reservation and information channels, governed by a network management center. Further analyses will cover tradeoffs between data and voice users, probability of blocking, and the performance impacts of on-board switching and variable bandwidth assignment. Initial calculations indicate that a large traffic volume can be handled with acceptable delays and voice blocking probabilities.

Li, V. O. K.↗
NASA NTRS1985

Development and flight test of a helicopter, X-band, portable precision landing system concept

A beacon landing system (BLS) is being developed and flight tested as a part of NASA's Rotorcraft All-Weather Operations Research Program. The system is based on state-of-the-art X-band radar technology and digital processing techniques. The BLS airborne hardware consists of an X-band receiver and a small microprocessor, installed in conjunction with the aircraft instrument landing system (ILS) receiver. The microprocessor analyzes the X-band, BLS pulses and outputs ILS-compatible localizer and glide slope signals. Range information is obtained using an on-board weather/mapping radar in conjunction with the BLS. The ground station is an inexpensive, portable unit; it weighs less than 70 lb and can be quickly deployed at a landing site. Results from the flight-test program show that the BLS has a significant potential for providing rotorcraft with low-cost, precision instrument approach capability in remote areas.

Davis, T. J.↗
NASA NTRS1978

Application of square-root filtering for spacecraft attitude control

Suitable digital algorithms are developed and tested for providing on-board precision attitude estimation and pointing control for potential use in the Landsat-D spacecraft. These algorithms provide pointing accuracy of better than 0.01 deg. To obtain necessary precision with efficient software, a six state-variable square-root Kalman filter combines two star tracker measurements to update attitude estimates obtained from processing three gyro outputs. The validity of the estimation and control algorithms are established, and the sensitivity of their performance to various error sources and software parameters are investigated by detailed digital simulation. Spacecraft computer memory, cycle time, and accuracy requirements are estimated.

Sorensen, J. A.↗
NASA NTRS1985

Civil helicopter flight operations using differential GPS

The results of NASA flight trials of a dual-receiver differential global positioning system (DGPS) for civilian helicopter navigation applications, are presented. The three principal components of the DGPS system are described, including the GPS ground-reference system, a range tracking system, and an on-board sequential GPS receiver. The ground-based receiver in the DGPS operates at a known fixed location and receives C/A code signals from NAVSTAR satellites. System bias errors in the ground receiver are subtracted from the airborne solution for the navigational fix. Calculations of the differential bias error are carried out using an on-board PDP-11/34 M research computer. The ground-reference differential corrections for satellites are given in a table. It is shown that the differential correction signal of the DGPS contains only a small (0.1 rad/sec) high-frequency component which can be attributed to system error. A schematic diagram of the DGPS postflight data processing routine is provided.

Edwards, F. G.↗
NASA NTRS1977

Innovations in Medicine

NASA is planning now toward the day of long-duration flight-manned interplanetary missions for example-wherein routine health care and emergency treatment must be accomplished on-board the spacecraft over periods of months or perhaps even years. Since spacecraft design limits crew size, the medical assignment may be handled by a single astronaut-physician or by a crew member trained as a physician's assistant. In a space emergency demanding surgery, for instance, sophisticated communications equipment, backed by a computerized data processing system, would make it possible for a surgeon on Earth to "examine" the patient. He could study X-rays and other data, specify an in-flight surgical procedure, and guide the astronaut-medic step-by-step through the operation. Such a system is being evaluated now. It is called STARPAHC (Space Technology Applied to Rural Papago Health Care). NASA technology in space communications and data processing is being applied to remote health services for the Papago tribe. STARPAHC is administered by the NASA Life Sciences Directorate in the Office of Space Sciences. It is a joint program involving NASA's Johnson Space Center, the Indian Health Service of the Department of Health, Education & Welfare, and the Papago's Executive Health Council. Lockheed Missiles & Space Co. is NASA's systems support contractor.

Source record↗
NASA NTRS1986

A flight expert system (FLES) for on-board fault monitoring and diagnosis

The increasing complexity of modern aircraft creates a need for a larger number of caution and warning devices. But more alerts require more memorization and higher work loads for the pilot and tend to induce a higher probability of errors. Therefore, an architecture for a flight expert system (FLES) to assist pilots in monitoring, diagnosing and recovering from in-flight faults has been developed. A prototype of FLES has been implemented. A sensor simulation model was developed and employed to provide FLES with the airplane status information during the diagnostic process. The simulator is based partly on the Lockheed Advanced Concept System (ACS), a future generation airplane, and partly on the Boeing 737, an existing airplane. A distinction between two types of faults, maladjustments and malfunctions, has led us to take two approaches to fault diagnosis. These approaches are evident in two FLES subsystems: the flight phase monitor and the sensor interrupt handler. The specific problem addressed in these subsystems has been that of integrating information received from multiple sensors with domain knowledge in order to assess abnormal situations during airplane flight. This paper describes the reasons for handling malfunctions and maladjustments separately and the use of domain knowledge in the diagnosis of each.

Ali, M.↗
NASA NTRS1980

On-board computers for control

On-board computers for control and sequencing from Apollo to Voyager are described along with future trends and recent design examples. Consideration is given to a high-order language for the Space Shuttle program. Emphasis is placed on the usage of modern LSI and new distributed architectural approaches. The distributed computer of the Galileo spacecraft and the data processing system for the Shuttle Orbiter are outlined.

Scull, J. R.↗
NASA NTRS1977

Flight data processing with the F-8 adaptive algorithm

An explicit adaptive control algorithm based on maximum likelihood estimation of parameters has been designed for NASA's DFBW F-8 aircraft. To avoid iterative calculations, the algorithm uses parallel channels of Kalman filters operating at fixed locations in parameter space. This algorithm has been implemented in NASA/DFRC's Remotely Augmented Vehicle (RAV) facility. Real-time sensor outputs (rate gyro, accelerometer and surface position) are telemetered to a ground computer which sends new gain values to an on-board system. Ground test data and flight records were used to establish design values of noise statistics and to verify the ground-based adaptive software. The software and its performance evaluation based on flight data are described

Hartmann, G.↗
NASA NTRS1980

A study of autonomous satellite navigation methods using the global positioning satellite system

Special orbit determination algorithms were developed to accommodate the size and speed limitations of on-board computer systems of the NAVSTAR Global Positioning System. The algorithms use square root sequential filtering methods. A new method for the time update of the square root covariance matrix was also developed. In addition, the time update method was compared with another square root convariance propagation method to determine relative performance characteristics. Comparisions were based on the results of computer simulations of the LANDSAT-D satellite processing pseudo range and pseudo range-rate measurements from the phase one GPS. A summary of the comparison results is presented.

Tapley, B. D.↗
NASA NTRS1974

Orbit determination for a Jupiter orbiter tour of the Galilean satellites

Current NASA planning envisions an ambitious Jupiter tour mission which will arrive at the planet in the year, 1984. The objectives of this mission are to broaden our knowledge of the outer solar system and in particular to extend our understanding of the physical processes at work in the Jupiter and Galilean satellite environment. To achieve these goals, precise spacecraft navigation is a fundamental requirement inasmuch as very near encounters with the satellites are necessary both for the planned scientific investigations and to reduce fuel requirements necessary for orbital insertion about the planet. This paper, deals with problems of producing precise spacecraft state estimates relative to the Galilean satellites, with the aid of both earth-based radio and on-board video data.

Russell, R. K.↗
NASA NTRS1977

Feasibility investigation of integrated optics Fourier transform devices

The possibility of producing an integrated optics data processing device based upon Fourier transformations or other parallel processing techniques, and the ways in which such techniques may be used to upgrade the performance of present and projected NASA systems were investigated. Activities toward this goal include; (1) production of near-diffraction-limited geodesic lenses in glass waveguides; (2) development of grinding and polishing techniques for the production of geodesic lenses in LiNbO3 waveguides; (3) development of a characterization technique for waveguide lenses; and (4) development of a theory for corrected aspheric geodesic lenses. A holographic subtraction system was devised which should be capable of rapid on-board preprocessing of a large number of parallel data channels. The principle involved is validated in three demonstrations.

Verber, C. M.↗
NASA NTRS1985

Remote sensing and disaster monitoring - A review of applications in Indonesia

The role played by remote sensors on-board the Landsat and NOAA-7 satellites in monitoring and management of three catastrophic events that took place in 1982 and 1983 in Indonesia (two major volcanic eruptions and a large-scale forest fire) is assessed. The modes of operation of the satellite platforms, the types of data derived, and data availability to the users are described, and the sources of failures and delays (such as the presence of clouds, technical and computer errors, red-tape, etc.) are examined. The major drawbacks of the Landsat-supplied information for monitoring short-lived and fast-changing events were the insufficient frequency of data acquisition, delayed delivery of data, and extended times needed for data distribution and processing. Indonesia's NOAA-7 and GMS sensors, although of low spatial resolution, offered higher frequency of data collection, and profited from the existence of a local receiving station. The present value of the space-based imagery is seen mainly in the baseline assessment of the disaster-prone areas, which can assist in preparing these areas for the impending catastrophic events.

Malingreau, J. P.↗
NASA NTRS1975

ITOS VHRR on-board data compression study

Data compression methods for ITOS VHRR data were studied for a tape recorder record-and playback application. A playback period of 9 minutes was assumed with a nominal 18 minute record period for a 2-to-1 compression ratio. Both analog and digital methods were considered with the conclusion that digital methods should be used. Two system designs were prepared. One is a PCM system and the other is an entropy-coded predictive-quantization, sometimes called entropy-coded DPCM or just DPCM, system. Both systems use data management principles to transmit only the necessary data. Both systems use a medium capacity standard tape recorder from specifications provided by the technical officer. The 10 to the 9th power bit capacity of the recorder is the basic limitation on the compression ratio. Both systems achieve the minimum desired 2 to 1 compression ratio. A slower playback rate can be used with the DPCM system due to a higher compression factor for better link performance at a given CNR in terms of bandwidth utilization and error rate. The report is divided into two parts. The first part summarizes the theoretical conclusions of the second part and presents the system diagrams. The second part is a detailed analysis based upon an empirically derived random process model arrived at from specifications and measured data provided by the technical officer.

Gray, R. M.↗
NASA NTRS1986

The Venus Balloon Project

On June 11 and 15, 1985, two instrumental balloons were released from the Soviet VEGA 1 and VEGA 2 spacecraft and deployed in the atmosphere of Venus. The VEGA probes flew by the planet on their way to a rendezvous with comet Halley in March 1986. Drifting with the wind at altitudes of 54 km, the balloons traveled one-third of the way around the planet during their 46-hour lifetimes. Sensors on-board the gondolas made periodic measurements of pressure, temperature, vertical wind velocity, cloud particle density, ambient light level, and frequency of lightning. The data were transmitted to Earth and received at the Deep Space Network (DSN) 64-m stations and at several large antennas in the USSR. Approximately 95 percent of the telemetry data were successfully decoded at the DSN complexes and in the Soviet Union, and were provided to the international science team for analysis. Very Long Baseline Interferometry (VLBI) data were acquired by 20 radio observatories around the world for the purpose of monitoring the Venus winds. The DSN 64-m subnet was part of a 15-station VLBI network organized by the Centre National d'Etudes Spatiales (CNES) of France. In addition, five antennas of the Soviet network participated. VLBI data from the CNES network are currently being processed at the Jet Propulsion Laboratory.

Stelzried, C. T.↗