Results for “partially” — Page 7

NASA NTRSDate not supplied

Functional Task Tests in Partial Gravity During Parabolic Flight

BACKGROUND Understanding how critical mission tasks are performed in partial gravity such as on the moon or Mars is necessary to define effective and comprehensive countermeasure strategies for preserving crew performance during exploration missions. We studied the performance of tasks such as standing, walking, and jumping during the partial gravity phases of parabolic flight. We hypothesized that the acute effects of partial gravity on vestibular, proprioceptive, and sensorimotor functions would negatively impact performance. METHODS Twelve subjects were tested over three flights of 30 parabolas each, including 10 parabolas at 0.25g, 10 parabolas at 0.5g, and 10 parabolas at 0.75g. Subjects also performed tests in 1g between parabolas. During the sit-to-stand with obstacle walk task, subjects rose from a seated position and walked as quickly as possible straight ahead towards a cone (4 m distance), walked around the cone making a 180° left turn, returned, and sat in the chair. On the way to and from the cone, subjects stepped over a 30 cm high obstacle. For the recovery from fall task, subjects lay prone for the pull-up phase and initial 10 sec of the parabola. Then they were asked to rise as quickly as possible and maintain a quiet stance for 10 sec. The tandem rail balance task involved standing with both feet on a 4.5 cm wide rail. The time ended when subjects either stepped off the rail or grabbed on to support straps. The jump down task started with the subjects standing on a 30 cm high platform, then the subjects were instructed to step off the platform, land with both feet simultaneously, and settle in a quiet stance. The cone of stability task involved subjects leaning about the ankles as far as they could in the anterior, posterior, and lateral directions without unfolding their arms or taking a step. The center of pressure distance between endpoints was calculated. Data were collected using inertial measurement units (Opal V2, APDM, Portland, OR) worn on the head and trunk, heart rate monitors (RS800CX, Polar, Kempele, Finland), and a force plate (Bertec, Columbus, OH). RESULTS Gravity level had a significant effect on performance, with the greatest changes from 1g tending to be at the 0.25g level (Table 1). Lower gravity levels were associated with increased times to complete the sit-to-stand obstacle walk task and the recovery from fall task, decreased change in heart rate during the recovery from fall task, decreased rail balance times, and increased cone of stability distance in the anterior-posterior direction. Table 1. Functional task performance at different gravity levels during parabolic flight. Measure0.25g0.5g0.75g1gp-valueSit-to-stand with obstacle walk time (sec)9.8 ±1.4*7.2 ±0.76.9 ±0.8*7.4 ±0.9<0.001Recovery from fall time to settle (sec)5.3 ± 0.9*4.6 ± 0.84.2 ± 0.64.3 ± 0.70.002Recovery from fall change in heart rate (bpm)6.0 ± 7.3*11.2 ± 6.5*14.9 ± 4.915.9 ± 6.5<0.001Rail balance with eyes open time (sec)2.7 ±0.8*4.8 ±2.16.6 ±4.78.4 ±6.70.031Rail balance with eyes closed time (sec)1.6 ±0.4*2.1 ±0.42.4 ±0.62.6 ±0.8<0.001Jump down time to settle (sec)2.1 ± 0.41.9 ± 0.42.0 ± 0.31.8 ± 0.30.328Cone of stability –anterior-posterior (cm)20.8 ±2.7*18.8 ±2.218.6 ±1.717.9 ±2.00.039Cone of stability –lateral (cm)26.8 ±6.624.4 ±2.123.0 ±2.123.8 ±2.30.215p-value: one-way repeated measures analysis of variance; *Significant pairwise difference from 1g (p<0.05). DISCUSSION These data suggest that there is a dose-response relationship between gravity level and functional task performance. The largest changes in performance were expected at the lowest gravity level (0.25g) because subjects would no longer be able to use the gravitational reference for the perception of upright. Understanding the extent of performance deficits informs the risks and design of countermeasures for exploration spaceflight missions. ACKNOWLEDGEMENT This work is supported by NASA’s Human Research Program Human Health Countermeasures Element.

T R Macaulay↗

NASA NTRS2025

Functional Task Tests in Partial Gravity During Parabolic Flight

BACKGROUND Understanding how critical mission tasks are performed in partial gravity such as on the moon or Mars is necessary to define effective and comprehensive countermeasure strategies for preserving crew performance during exploration missions. We studied the performance of tasks such as standing, balancing, walking, and jumping during the partial gravity phases of parabolic flight. We hypothesized that the acute effects of partial gravity on vestibular, proprioceptive, and sensorimotor functions would negatively impact performance. METHODS Twelve subjects (6F, 6M; 40.2 ± 8.5 years) were tested over three flights of 30 parabolas each, including 10 parabolas at 0.25g, 10 parabolas at 0.5g, and 10 parabolas at 0.75g. Subjects also performed tests in 1g between parabolas. During the seat egress and walk task, subjects rose from a seated position and walked as quickly as possible straight ahead towards a cone (4 m distance), stepped over a 30 cm high obstacle, walked around the cone making a 180° left turn, returned to the chair, and sat down in the chair. Other tasks included a tandem stance on rails, jump down from a 30cm platform, recovery from fall (prone to stand), and limits of stability tasks. Data were collected using inertial measurement units (Opal V2, APDM, Portland, OR) worn on the head and trunk, heart rate monitors (Polar, Finland), and a force plate (Bertec, Columbus, OH). During the jump down and limits of stability tasks, falls were recorded if subjects took extra steps, lifted their heels/toes, or used their arms to recover balance. RESULTS Gravity level had a significant effect on performance, with the greatest changes from 1g tending to be at the 0.25g level (Table 1). Lower gravity levels were associated with increased times to complete the seat egress and walk task and the recovery from fall task, increased head-trunk coordination, decreased tandem stance rail balance times, decreased change in heart rate during the recovery from fall task, and increased cone of stability distance in the anterior-posterior direction. In addition, there were significantly more falls recorded at the lower gravity levels: 31 falls at 0.25g, 14 falls at 0.5g, 6 falls at 0.75g, and 6 falls at 1g. DISCUSSION These data suggest that there is a dose-response relationship between gravity level and functional task performance. The largest changes in performance were expected at the lowest gravity level (0.25g) because subjects would no longer be able to use the gravitational reference for the perception of upright. Understanding the extent of performance deficits informs the risks and design of countermeasures for exploration spaceflight missions.

T R Macaulay↗

NASA NTRS1966

Simulator effects partial gravity conditions

Adjustable apparatus which simulates partial to zero gravity partially supports the weight of convalescing patients in rehabilitation exercises. This device is an ideal tool for physical therapy.

Johnson, H. I.↗

NASA NTRS1972

Partial reflections of radio waves from the lower ionosphere

The addition of phase difference measurements to partial reflection experiments is discussed, and some advantages of measuring electron density this way are pointed out. The additional information obtained reduces the requirement for an accurate predetermination of collision frequency. Calculations are also made to estimate the errors expected in partial-reflection experiments due to the assumption of Fresnel reflection and to the neglect of coupling between modes. In both cases, the errors are found to be of the same order as known errors in the measurements due to current instrumental limitations.

Connolly, D. J.↗

NASA NTRS1971

Similarity and generalized finite-difference solutions of parabolic partial differential equations.

Techniques are presented for obtaining generalized finite-difference solutions to partial differential equations of the parabolic type. It is shown that the advantages of similarity in the solution of similar problems are generally not lost if the solution to the original partial differential equations is effected in the physical plane by finite-difference methods. The analysis results in a considerable saving in computational effort in the solution of both similar and nonsimilar problems. Several examples, including both the heat-conduction equation and the boundary-layer equations, are given. The analysis also provides a practical means of estimating the accuracy of finite-difference solutions to parabolic equations.

Clausing, A. M.↗

NASA NTRS1972

Mode coupling in partial reflections from the ionosphere at vertical incidence.

The effect of mode coupling has been calculated for radio waves partially reflected from the lower ionosphere at vertical incidence. Calculations were made for parameters appropriate to the partial reflection experiments (Belrose, 1970). The four reflection coefficients (two direct and two coupled) are calculated for a plane discontinuity using a matrix perturbation analysis. The ratios of coupled to direct reflection coefficients are calculated for a general one-dimensional reflecting layer using the coupled equations of Clemmow and Heading (1954). At the highest electron density considered, 10,000 per cu cm, about 10% of the reflected extraordinary wave amplitude might be due to coupling from the incident ordinary wave. The effect is smaller at lower electron density.

Connolly, D. J.↗

NASA NTRS1973

Steady, subsonic, lifting surface theory for wings with swept, partial span, trailing edge control surfaces

A method for computing the lifting pressure distribution on a wing with partial span, swept control surfaces is presented. This method is valid within the framework of linearized, steady, potential flow theory and consists of using conventional lifting surface theory in conjuction with a flap pressure mode. The cause of a numerical instability that can occur during the quadrature of the flap pressure mode is discussed, and an efficient technique to eliminate the instability is derived. This technique is valid for both the flap pressure mode and regular pressure modes and could be used to improve existing lifting surface methods. Examples of the use of the flap pressure mode and comparisons among this method, other theoretical methods, and experiments are given. Discrepancies with experiment are indicated and candidate causes are presented. It is concluded that the method can lead to an efficient and accurate solution of the mathematical problem when a partial span, trailing edge flap is involved.

Medan, R. T.↗

NASA NTRS1973

Net radiation method for enclosure systems involving partially transparent walls

The net radiation method is developed for analyzing radiation heat transfer in enclosure systems involving partially transparent walls. One such system is an enclosure with windows in it. The conventional net radiation method was developed for enclosures having opaque walls. If a partially transparent wall is present, it will permit radiation to enter and leave the enclosure. The net radiation equations are developed here for gray and semigray enclosures with one or more windows. Another system of interest, such as in a flat plate solar collector, consists of a series of parallel transparent layers. The transmission characteristics of such window systems are obtained by the net radiation method, and the technique appears to be more convenient than the ray tracing method which has been used in the past. Relations are developed for windows consisting of any number of parallel layers having differing absorption coefficients and differing surface reflectivities, and for systems composed of parallel transmitting layers and opaque plates.

Siegel, R.↗

NASA NTRS1973

Analysis of axisymmetrical vibration of a partially liquid-filled elastic sphere by the method of Green's function

The longitudinal dynamic behavior of launch vehicles is largely determined by their huge liquid propellant masses which are spring supported by the elastic tank walls. Throughout much of the powered flight time, these masses constitute a high percentage of the entire vehicle mass and, therefore, may dominate the fundamental modes of the vehicle. In this report, a spherical container is considered. The analysis is based on a Galerkin approach, in the course of which a second-order differential equation must be solved. The solution has been obtained by the method of Green's function. This method is favorable because it displays the manner in which the analysis can be extended to partially liquid-filled general shells of revolution. The computer programs currently available for partially liquid-filled propellant tanks are based on the finite element methods and result in analytical models having as many as several hundred degrees of freedom. The method applied in this report results in a model having less than 10 degrees of freedom as can be shown by numerical evaluation. Therefore, it will be possible to analyze propellant tanks using much less computer time with comparable accuracy.

Glaser, R. F.↗

NASA NTRS1973

Calculation of total electron excitation cross-sections and partial electron ionization cross-sections for the elements

Computer programs were used to calculate the total electron excitation cross-section for atoms and the partial ionization cross-section. The approximations to the scattering amplitude used are as follows: (1) Born, Bethe, and Modified Bethe for non-exchange excitation; (2) Ochkur for exchange excitation; and (3) Coulomb-Born of non-exchange ionization. The amplitudes are related to the differential cross-sections which are integrated to give the total excitation (or partial ionization) cross-section for the collision. The atomic wave functions used are Hartree-Fock-Slater functions for bound states and the coulomb wave function for the continuum. The programs are presented and the results are examined.

Green, T. J.↗

NASA NTRS1974

Stability of partially lined combustors with distributed combustion

An integral method for theoretical evaluation of the stability of confined flows with mass sources is presented. This method is applied to evaluate the effect of partial length acoustic liners on liquid propellant combustors with distributed combustion sources. The combustor is modeled as a right circular cylinder terminated by a multiorifice (constant Mach number) nozzle. The spatial spread of combustion in the chamber is represented by an arbitrary number of pressure sensitive planar mass sources. On the cylindrical periphery of the chamber is an acoustic absorber of arbitrary length, position, and damping capability. Integral equations are developed from the partial differential equations describing the nonsteady flow and are solved iteratively. Results are given in terms of linear neutral stability plots using a pressure sensitive combustion response. Calculations indicate that increasing the axial spread of combustion increases the stability of the combustor and the effectiveness of the absorber. The most effective linear placement appears at the location of greatest combustion concentration.

Baer, M. R.↗

NASA NTRS1974

A plate with a crack, stiffened by a partially debonded stringer

The effect of a partially debonded infinite stringer on the stress intensity factor at the crack tip is investigated. It is assumed that the stringer is bonded to an isotropic plate through an adhesive, along a line perpendicular to the crack. Due to the high stress concentration around the crack tip and on the adhesive, partial debonding is assumed to develop between the stringer and the plate. The integral equation, obtained from the continuity of displacements along the line where the stringer and the plate are bonded, is solved numerically to give the shear stress distribution between the plate and the stringer and the stress intensity factors at both crack tips.

Arin, K.↗

NASA NTRS1974

Partial equilibrium model for predicting concentration of CO in combustion

A simple kinetic model, based upon the concept of partial equilibrium, is developed for predicting carbon monoxide concentrations in such steady-flow hydrocarbon-air combustion systems as gas-turbine combustors. The only two kinetic constraints used in the model are on the rate of change of the total number of gaseous particles in the system, and on the rate of change of the CO concentration. The accuracy of the model is verified by comparison with experimental results obtained by burning kerosene with air in a 130,000 Btu/hr atmospheric-pressure steady-flow burner. Burnt-gas cooling rates of 1,000,000 K/sec, about the magnitude encountered in the dilution zone of gas-turbine combustors, were obtained with a compact water-cooled heat exchanger. Good agreement between measured CO concentrations and the values predicted by the partial-equilibrium model was obtained.

Morr, A. R.↗

NASA NTRS1975

Higher order accurate partial implicitization: An unconditionally stable fourth-order-accurate explicit numerical technique

The previously obtained second-order-accurate partial implicitization numerical technique used in the solution of fluid dynamic problems was modified with little complication to achieve fourth-order accuracy. The Von Neumann stability analysis demonstrated the unconditional linear stability of the technique. The order of the truncation error was deduced from the Taylor series expansions of the linearized difference equations and was verified by numerical solutions to Burger's equation. For comparison, results were also obtained for Burger's equation using a second-order-accurate partial-implicitization scheme, as well as the fourth-order scheme of Kreiss.

Graves, R. A., Jr.↗

NASA NTRS1974

Shock-wave structure in a partially ionized gas

The structure of a steady plane shock in a partially ionized gas has been investigated using the Boltzmann equation with a kinetic model as the governing equation and the discrete ordinate method as a tool. The effects of the electric field induced by the charge separation on the shock structure have also been studied. Although the three species of an ionized gas travel with approximately the same macroscopic velocity, the individual distribution functions are found to be very different. In a strong shock the atom distribution function may have double peaks, while the ion distribution function has only one peak. Electrons are heated up much earlier than ions and atoms in a partially ionized gas. Because the interactions of electrons with atoms and with ions are different, the ion temperature can be different from the atom temperature.

Lu, C. S.↗

NASA NTRS1975

Resonance line transfer with partial redistribution. IV - A generalized formulation for lines with common upper states. V - The solar Ca II lines

A generalized formulation is given for treating partial redistribution effects in transfer problems in resonance lines with common upper states. The formulation allows explicitly for the possibility that several spectral lines may arise in transitions from a given upper level to several sharp lower levels, including, for example, the ground state and metastable states. Line profiles for the Ca II H and K lines have been calculated, accounting for the partial frequency coherence of scattered photons. These profiles are compared with calculations made with identical atomic and atmospheric models but assuming complete redistribution. Very significant differences between the profiles obtained using these two different physical descriptions of the scattering process are found, and it is now apparent that the assumption of complete redistribution is a serious oversimplification of the actual physical situation. The results question the validity of equating brightness temperatures observed at K(sub 1) in stellar spectra with minimum temperatures in stellar chromospheres; it appears likely that such a procedure will systematically underestimate the value of T-min.

Milkey, R. W.↗

NASA NTRS1976

User's guide to computer program CIVM-JET 4B to calculate the transient structural responses of partial and/or complete structural rings to engine-rotor-fragment impact

A user-oriented computer program CIVM-JET 4B is described to predict the large-deflection elastic-plastic structural responses of fragment impacted single-layer: (a) partial-ring fragment containment or deflector structure or (b) complete-ring fragment containment structure. These two types of structures may be either free or supported in various ways. Supports accommodated include: (1) point supports such as pinned-fixed, ideally-clamped, or supported by a structural branch simulating mounting-bracket structure and (2) elastic foundation support distributed over selected regions of the structure. The initial geometry of each partial or complete ring may be circular or arbitrarily curved; uniform or variable thicknesses of the structure are accommodated. The structural material is assumed to be initially isotropic; strain hardening and strain rate effects are taken into account.

Stagliano, T. R.↗

NASA NTRS1976

The Lockheed alternate partial polarizer universal filter

A tunable birefringent filter using an alternate partial polarizer design has been built. The filter has a transmission of 38% in polarized light. Its full width at half maximum is .09A at 5500A. It is tunable from 4500 to 8500A by means of stepping motor actuated rotating half wave plates and polarizers. Wave length commands and thermal compensation commands are generated by a PPD 11/10 minicomputer. The alternate partial polarizer universal filter is compared with the universal birefringent filter and the design techniques, construction methods, and filter performance are discussed in some detail. Based on the experience of this filter some conclusions regarding the future of birefringent filters are elaborated.

Title, A. M.↗