SEARCH · Search NASA

Results for “passive barrier”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS2011

High-Operating-Temperature Barrier Infrared Detector with Tailorable Cutoff Wavelength

A mid-wavelength infrared (MWIR) barrier photodetector is capable of operating at higher temperature than the prevailing MWIR detectors based on InSb. The standard high-operating-temperature barrier infrared detector (HOT-BIRD) is made with an InAsSb infrared absorber that is lattice-matched to a GaSb substrate, and has a cutoff wavelength of approximately 4 microns. To increase the versatility and utility of the HOT-BIRD, it is implemented with IR absorber materials with customizable cutoff wavelengths. The HOT-BIRD can be built with the quaternary alloy GaInAsSb as the absorber, GaAlSbAs as the barrier, on a lattice-matching GaSb substrate. The cutoff wavelength of the GaInAsSb can be tailored by adjusting the alloy composition. To build a HOT-BIRD requires a matching pair of absorber and barrier materials with the following properties: (1) their valence band edges must be approximately the same to allow unimpeded hole flow, while their conduction band edges should have a large difference to form an electron barrier; and (2) the absorber and the barrier must be respectively lattice-matched and closely lattice-matched to the substrate to ensure high material quality and low defect density. To make a HOT-BIRD with cutoff wavelength shorter than 4 microns, a GaInAsSb quaternary alloy was used as the absorber, and a matching GaAlSbAs quaternary alloy as the barrier. By changing the alloy composition, the band gap of the quaternary alloy absorber can be continuously adjusted with cutoff wavelength ranging from 4 microns down to the short wavelength infrared (SWIR). By carefully choosing the alloy composition of the barrier, a HOT-BIRD structure can be formed. With this method, a HOT-BIRD can be made with continuously tailorable cutoff wavelengths from 4 microns down to the SWIR. The HOT-BIRD detector technology is suitable for making very-large-format MWIR/SWIR focal plane arrays that can be operated by passive cooling from low Earth orbit. High-operating temperature infrared with reduced cooling requirement would benefit space missions in reduction of size, weight, and power, and an increase in mission lifetime.

Ting, David Z.↗

DOE OSTI2021

Clearing a Path to Commercialization of Marine Renewable Energy Technologies Through Public–Private Collaboration

Governments are increasingly turning toward public–private partnerships to bring industry support to improving public assets or services. Here, we describe a unique public–private collaboration where a government entity has developed mechanisms to support public and private sector advancement and commercialization of monitoring technologies for marine renewable energy. These support mechanisms include access to a range of skilled personnel and test facilities that promote rapid innovation, prove reliability, and inspire creativity in technology development as innovations move from concept to practice. The ability to iteratively test hardware and software components, sensors, and systems can accelerate adoption of new methods and instrumentation designs. As a case study, we present the development of passive acoustic monitoring technologies customized for operation in energetic waves and currents. We discuss the value of testing different systems together, under the same conditions, as well as the progression through different test locations. The outcome is multiple, complementary monitoring technologies that are well suited to addressing an area of high environmental uncertainty and reducing barriers to responsible deployment of low-carbon energy conversion systems, creating solutions for the future.

16 TIDAL AND WAVE POWER↗

DOE OSTI2025

Degradation and Accelerated Recovery of Surface Passivation in n+, p+, and Intrinsic Poly-Si/SiOx Passivating Contacts for Silicon Solar Cells

We report on the degradation and recovery of surface passivation of fired poly-Si/SiOx passivating contacts with hydrogen containing Al2O3 during annealing in the dark and under illumination. Upon firing to a peak temperature of 670 degrees C, the iVoc for symmetric test structures with n+, p+, and intrinsic poly-Si/SiOx contacts decreases due to a loss of surface passivation. Upon further annealing over the temperature range of 200-350 degrees C in the dark, depending on the type of doping, the surface passivation either shows further degradation followed by recovery, or direct recovery to the initial iVoc. Annealing at higher temperatures and/or higher illumination intensities accelerates the kinetics for both degradation and recovery processes. We show that the degradation and recovery processes are thermally activated and proceed identically in subsequent firing and annealing steps showing their cyclic nature. We present a series reaction model to explain the kinetics of degradation and recovery processes for n+ and intrinsic poly-Si/SiOx contacts. By fitting the model's rate expressions to the data, the determined effective activation energy barriers for degradation and recovery for n+ poly-Si/SiOx contacts in the dark are 1.24 and 1.51 eV, which are lowered under 7.5 Suns illumination to 0.76 and 1.15 eV, respectively.

14 SOLAR ENERGY↗

NASA NTRS2007

High Temperature Materials for Chemical Propulsion Applications

Radiation or passively cooled thrust chambers are used for a variety of chemical propulsion functions including apogee insertion, reaction control for launch vehicles, and primary propulsion for planetary spacecraft. The performance of these thrust chambers is limited by the operating temperature of available materials. Improved oxidation resistance and increased operating temperatures can be achieved with the use of thermal barrier coatings such as zirconium oxide (ZrO2) and hafnium oxide (HfO2). However, previous attempts to include these materials showed cracking and spalling of the oxide layer due to poor bonding. Current research at NASA's Marshall Space Flight Center (MSFC) has generated unique, high temperature material options for in-space thruster designs that are capable of up to 2500 C operating temperatures. The research is focused on fabrication technologies to form low cost Iridium,qF_.henium (Ir/Re) components with a ceramic hot wall created as an integral, functionally graded material (FGM). The goal of this effort is to further de?celop proven technologies for embedding a protective ceramic coating within the Ir/Re liner to form a robust functional gradient material. Current work includes the fabrication and testing of subscale samples to evaluate tensile, creep, thermal cyclic/oxidation, and thermophysical material properties. Larger test articles have also being fabricated and hot-fire tested to demonstrate the materials in prototype thrusters at 1O0 lbf thrust levels.

Elam, Sandra↗

DOE OSTI2021

A perspective on ordered vacancy compound and parent chalcopyrite thin film absorbers for photoelectrochemical water splitting

Chalcopyrites could fill the gap between the low-cost, poor-efficiency single junction metal oxide photoelectrochemical (PEC) water splitting cells and the high efficiency, yet costly III–V tandems. In this Perspective, we first review the key barriers that must be addressed by the community to enable economical chalcopyrite-based PEC water splitting. Then, we highlight how theoretical modeling can be used to identify promising ordered vacancy compound absorbers with improved energetics compared to their chalcopyrite parents. Finally, we describe how advanced spectroscopic analysis performed on chalcopyrite photocathodes after PEC testing uncovered a new passivation layer candidate for prolonged durability.

08 HYDROGEN↗

DOE OSTI2022

On the broadband vibration isolation performance of nonlocal total-internal-reflection metasurfaces

The concept of a nonlocal elastic metasurface has been recently proposed and experimentally demonstrated in Zhu et al. (2020). When implemented in the form of a total-internal-reflection (TIR) interface, the metasurface can act as an elastic wave barrier that is impenetrable to deep subwavelength waves over an exceptionally wide frequency band. The underlying physical mechanism capable of delivering this broadband subwavelength performance relies on an intentionally nonlocal design that leverages long-range connections between the units forming the fundamental supercell. This paper explores the design and application of a nonlocal TIR metasurface to achieve broadband passive vibration isolation in a structural assembly made of multiple dissimilar elastic waveguides. The specific structural system comprises shell, plate, and beam waveguides, and can be seen as a prototypical structure emulating mechanical assemblies of practical interest for many engineering applications. The study also reports the results of an experimental investigation that confirms the significant vibration isolation capabilities afforded by the embedded nonlocal TIR metasurface. We report these results are particularly remarkable because they show that the performance of the nonlocal metasurface is preserved when applied to a complex structural assembly and under non-ideal incidence conditions of the incoming wave, hence significantly extending the validity of the results presented in Zhu et al. (2020). Results also confirm that, under proper conditions, the original concept of a planar metasurface can be morphed into a curved interface while still preserving full wave control capabilities.

42 ENGINEERING↗

DOE OSTI2020

Modeling Interfaces to Support Low-Level Waste Disposal System Performance Assessments - 20366

In low-level waste (LLW) disposal sites, interfaces between cementitious materials, used as waste forms and/or engineered barriers, and the surrounding soil or backfill material are often encountered. Reactions across these interfaces may lead to chemical and structural alteration of the cementitious and backfill materials that may ultimately affect long-term performance. For example, the ingress of carbon dioxide from soil gas into a waste tank concrete shell at the Hanford Site or Savannah River Site (SRS) or a low-level waste disposal vault at SRS leads to carbonation of cement hydration products (e.g. portlandite, calcium-silicate hydrate or C-S-H, and ettringite). The result of carbonation is a decrease in pH in the cement paste portion of the tank wall or vault concrete structure that could ultimately lead to de-passivation of the embedded structural steel and, eventually, to cracking. Cracking can lead to increased ingress of water into the structure, corresponding increased release of constituents of concern, and to subsequent increased transport of these constituents to the surrounding environment. The mobility of trace constituents (e.g., radionuclides of concern) in waste forms may increase in response to changes in pH, pore structure, and mineralogical gradients. Depletion of portlandite results in subsequent decalcification of C-S-H that leads to changes in the cement strength and may lead to structural failure. At the boundary between waste forms and concrete vaults, the migration of sulfate ions from the salt waste form (e.g., the saltstone waste form used for LLW disposal at the Savannah River Site in Saltstone Disposal Units, or SDUs) into the barrier or vault concrete has been predicted to result in expansive mineral phase formation (or 'sulfate attack'). Expansive mineral formation could result in cracking and potential loss of structural integrity in the vault concrete. In the performance assessment (PA) for the SRS SDUs, prediction of both the carbonation and sulfate attack fronts are critical to assessing the long-term performance of these LLW disposal vaults. A general purpose geochemical reactive transport model has been developed in LeachXS/ORCHESTRA to evaluate typical interfaces for LLW disposal environments, including SDUs at SRS. The model may be used to predict the long-term performance of interfaces between cementitious materials and saltstone or backfill materials with respect to primary phases by considering mass transport, cement chemistry, geochemical speciation, and multi-ionic diffusion over interfaces between different materials. The present study compares the performance and interactions between vault concrete and saltstone waste form for a representative SDU scenario. The materials were characterized using pH-dependence leaching test (EPA 1313) and semi-dynamic transport tests (EPA 1315) with test results used to parameterize the interface model. The development of a credible inter model provides an important basis for supporting future PAs where carbonation and sulfate attack are important aging and degradation mechanisms. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS2022

SoMoGym: A Toolkit for Developing and Evaluating Controllers and Reinforcement Learning Algorithms for Soft Robots

Soft robotsoffer a host of benefits over traditional rigid robots, including inherent compliance that lets them passively adapt to variable environments and operate safely around humans and fragile objects. However, that same compliance makes it hard to use model-based methods in planning tasks requiring high precision or complex actuation sequences. Reinforcement learning (RL) can potentially find effective control policies, but training RL using physical soft robots is often infeasible, and training using simulations has had a high barrier to adoption. To accelerate research in control and RL for soft robotic systems, we introduce SoMoGym ( So ft Mo tion Gym ), a software toolkit that facilitates training and evaluating controllers for continuum robots. SoMoGym provides a set of benchmark tasks in which soft robots interact with various objects and environments. It allows evaluation of performance on these tasks for controllers of interest, and enables the use of RL to generate new controllers. Custom environments and robots can likewise be added easily. We provide and evaluate baseline RL policies for each of the benchmark tasks. These results show that SoMoGym enables the use of RL for continuum robots, a class of robots not covered by existing benchmarks, giving them the capability to autonomously solve tasks that were previously unattainable.

Moritz A. Graule↗

DOE OSTI2023

Accelerated Characterization of Electrode‐Electrolyte Equilibration

Operational durability is poorly characterized by traditional (photo)electrocatalyst discovery workflows, creating a barrier to scale-up and deployment. Corrosion is a prominent degradation mechanism whose thermodynamics depend on the concentration of corrosion products in electrolyte. We present an automated system for characterizing the equilibration of (photo)electrodes with dissolved metals in electrolyte for a given electrode, pH, and electrochemical potential. Automation of electrode selection, electrolyte preparation, and electrolyte aliquoting enables rapid identification of self-passivating electrodes and estimation of the equilibrium dissolved metals concentrations. The technique is demonstrated for metal oxide photoanodes in alkaline electrolyte, where BiVO 4 is found to continually corrode, in agreement the literature. An amorphous Ni−Sb−O photoanode is found to passivate with a Ni-rich coating on the order of 1 monolayer with less than 1 μM total dissolved metals in electrolyte, demonstrating its suitability for durable photoelectrochemical operation. The automation and throughput of the instrument are designed for incorporation in accelerated electrocatalyst discovery workflows so that durability can be considered on equal footing with activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Delineating the Factors Impacting the Electrochemical Behavior of Single-Crystal High-Nickel Layered Oxide Cathodes

High-nickel (Ni) (≥80%) single-crystal LiNi 1-x-y Mn x Co y O 2 (NMCs) have garnered recent interest as cathodes in lithium (Li)-ion batteries (LIBs). However, capacity fade at high voltages, particularly after the onset of the H2–H3 phase transition, hampers their viability. In this study, single-crystal LiNi 0.8 Mn x Co 0.2-x O 2 (x = 0.2, 0.1, 0) are synthesized and tested in LiPF 6 in ethyl methyl carbonate-based electrolytes, with and without monofluoroethylene carbonate and LiF 2 PO 2 additives, to clarify the effects of Co/Mn ratio and surface stabilization on high-voltage cycling degradation. By imposing a kinetic barrier to the accessible H2–H3 capacity, surface reconstruction is identified as the primary driver of high-voltage capacity loss, being greater in the Co-free cathode and in the absence of fluorinated electrolyte components. This is attributed to a synergy between increased mechanical stress due to worsened bulk and interfacial H2–H3 kinetics and decreased interfacial stability due to the poor passivating capability of the electrolyte. Here, the findings highlight the importance of limiting cathode impedance growth during high-voltage cycling, which can be achieved by tuning bulk dopants and electrolyte chemistry.

25 ENERGY STORAGE↗

DOE OSTI2020

bifiPV2020 Bifacial Workshop: A Technology Overview

The virtual bifiPV Workshop was held in July 2020 to provide the solar industry with a forum for sharing and discussing research into bifacial photovoltaic (PV) technology. This report outlines major insights from the workshop to give the reader an overview of the latest developments in bifacial PV technology worldwide, from the lab to the field. Citations are drawn from this workshop unless otherwise noted, with all proceedings available online at bifipvworkshop. com. Presentations for the bifiPV2020 Workshop focused on the following areas: bifacial power plant modeling and simulation, albedo improvements, the development of encapsulants, the durability and reliability of current bifacial technologies, performance comparisons between glass-glass and glass-transparent backsheet configurations, the future of passivated emitter and rear contact (PERC) solar cells, and the growing adoption of n-type solar cells. With 650 GW total PV installed worldwide and 1 TW to come very soon, PERC is now the standard PV cell type produced en masse. However, it is already reaching 23% efficiency, the upper limit for this type of technology. PV modules breaking the 0.5-kW barrier are starting to appear, and the costs of standard PERC technology are already below 0.2 USD/Wp. In 2019, five GW of bifacial PV were installed worldwide. In 2020, the majority of bifacial installations are expected to be located in the United States, China, and Middle East and North Africa (MENA) states. N-type bifacial technologies are becoming increasingly viable and have huge potential to dominate the market in the coming years. With bifacial technology mounted on horizontal single-axis trackers (HSAT), bids below 10 USD/MWh will soon be observed in the MENA region, and later in Chile and the United States. Factory audits and reliability testing can reduce field failures by helping buyers to select producers that follow rigorous quality assurance and quality control processes.

14 SOLAR ENERGY↗

DOE OSTI2020

bifiPV2020 Bifacial Workshop: A Technology Overview

The virtual bifiPV Workshop was held in July 2020 to provide the solar industry with a forum for sharing and discussing research into bifacial photovoltaic (PV) technology. This report outlines major insights from the workshop to give the reader an overview of the latest developments in bifacial PV technology worldwide, from the lab to the field. Citations are drawn from this workshop unless otherwise noted. Presentations for the bifiPV2020 Workshop focused on the following areas: bifacial power plant modeling and simulation, albedo improvements, the development of encapsulants, the durability and reliability of current bifacial technologies, performance comparisons between glass-glass and glass-transparent backsheet configurations, the future of passivated emitter and rear contact (PERC) solar cells, and the growing adoption of n-type solar cells. With 650 GW total PV installed worldwide and 1 TW to come very soon, PERC is now the standard PV cell type produced en masse. However, it is already reaching 23% efficiency, the upper limit for this type of technology. PV modules breaking the 0.5-kW barrier are starting to appear, and the costs of standard PERC technology are already below 0.2 USD/Wp. In 2019, five GW of bifacial PV were installed worldwide. In 2020, the majority of bifacial installations are expected to be located in the United States, China, and Middle East and North Africa (MENA) states. N-type bifacial technologies are becoming increasingly viable and have huge potential to dominate the market in the coming years. With bifacial technology mounted on horizontal single-axis trackers (HSAT), bids below 10 USD/MWh will soon be observed in the MENA region, and later in Chile and the United States. Factory audits and reliability testing can reduce field failures by helping buyers to select producers that follow rigorous quality assurance and quality control processes.

14 SOLAR ENERGY↗

DOE OSTI2021

Effect of Cu on the passivity of Ti–xCu (x = 0, 3 and 5 wt%) alloy in phosphate-buffered saline solution within the framework of PDM-II

The effect of copper content on the passivity of Ti–xCu alloys in a phosphate-buffered saline electrolyte (pH 7.4), in the steady-state condition, was examined using potentiostatic polarization, electrochemical impedance spectroscopy, and Mott-Schottky analysis. The study demonstrates that the oxide layer forms on the Ti–xCu alloys surface have n-type semiconducting character, and the steady-state thickness of the oxide layer is observed linearly and depends on the applied potential. The study observations are in line with the predictions of the Point Defect Model (PDM-II), which provides a physiochemically realistic description of the oxide layer formation on Ti–xCu alloys. The observations reveal that the Cu additions result in a decrease in the charge transfer resistance and capacitances associated with the hydroxide and barrier layer, an increase in the donor density, and reduce the electrochemical resistance of the Ti–xCu alloys. The study also exhibits that the decrease in the steady-state current density after the initial addition of 3 wt% of Cu is attributed to the progressive substitution of copper on the cation sublattice of the film resulting in enhanced electrostatic interaction between the immobilized copper $Cu^{x'}_{Ti}$, and the mobile cation interstitials $Cu^{+}_{i}$, which carries the excess current over and that conveyed by oxygen vacancies $V^{••}_o$ in the barrier layer. Moreover, it is also observed that over a hundred-year implant period, about 0.006 cm (0.06 mm) of Ti–3Cu alloy is predicted to lose due to steady-state corrosion in the PBS solution under the given set of conditions, it is further seen that, as the Cu amount increased from 3 wt% to 5 wt% in the Ti–xCu alloys, the steady-state corrosion rate decreases.

Electrochemical Impedance Spectroscopy↗

DOE OSTI2023

SAM Code Development for Source Term Modeling in Fluoride-salt-cooled High-temperature Reactors

The SAM code is under development and supported by DOE-NE’s Nuclear Energy Advanced Modeling and Simulation program as a modern system-level modeling and simulation tool for advanced non-light water reactor safety analyses. These advanced reactor concepts incorporate novel and improved approaches to achieve safety and economic feasibility. Many concepts leverage higher operating temperatures for improved efficiency with a variety of coolants and structural materials to support those needs. Such design choices may also pose unique radiological source term risks. There are continuous efforts to incorporate new physics and phenomena relevant to advanced reactor concepts, including capabilities to enable system-level source term modeling. The Pebble-Bed Fluoride-salt-cooled High-temperature Reactor (PB-FHR) is a promising candidate among advanced nuclear reactor concepts with its improved passive safety characteristics and high thermal efficiency. In addition to past efforts to support the development and utilization of SAM for PB-FHR safety analysis, the species transport modeling capabilities in SAM have been extended to simulate source term phenomena in concepts like the PB-FHR. The PB-FHR concept utilizes pebble-form TRISO fuel and FLiBe salt coolant to provide robust barriers to the release of almost all fission products and radiological source terms. However, tritium poses a unique radiological risk due to its significant production from neutron interactions with 6 Li and 9 Be in the FLiBe as well as its high mobility at elevated temperatures where it can permeate through structural metals. Secondly, the use of graphite at elevated temperatures poses the risk of oxidation damage to any structural components or fuel pebbles that are exposed to accidental air ingress. This report summarizes progress made in modeling these phenomena in SAM, which leverages the system-level multi-physics thermal hydraulic simulation to support an effective engineering-scale source term modeling capability. A tritium transport model is developed to simulate the various transport pathways in FHR and MSR concepts and is presented through verification and validation examples as well as demonstrations simulating experimental test loops and reference plant FHR models. A graphite oxidation model is also introduced to calculate local oxidation rates and is presented with initial validation results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

The passivity of lithium electrodes in liquid electrolytes for secondary batteries

Rechargeable Li metal batteries are currently limited by electrolyte decomposition and rapid Li consumption. Li plating and stripping greatly depend on the solid electrolyte interphase formed at the Li metal-liquid electrolyte interface. This Review discusses the reactions occurring at this interface from a corrosion science perspective, highlighting the requirements for an ideal passivation layer. Rechargeable Li metal batteries are currently limited by safety concerns, continuous electrolyte decomposition and rapid consumption of Li. These issues are mainly related to reactions occurring at the Li metal-liquid electrolyte interface. Additionally, the formation of a passivation film (that is, a solid electrolyte interphase) determines ionic diffusion and the structural and morphological evolution of the Li metal electrode upon cycling. In this Review, we discuss spontaneous and operation-induced reactions at the Li metal-electrolyte interface from a corrosion science perspective. We highlight that the instantaneous formation of a thin protective film of corrosion products at the Li surface, which acts as a barrier to further chemical reactions with the electrolyte, precedes film reformation, which occurs during subsequent electrochemical stripping and plating of Li during battery operation. Finally, we discuss solutions to overcoming remaining challenges of Li metal batteries related to Li surface science, electrolyte chemistry, cell engineering and the intrinsic instability of the Li metal-electrolyte interface.

25 ENERGY STORAGE↗

DOE OSTI2023

Biochemical Process Modeling and Simulation (BPMS)

The Biochemical Process Modeling and Simulation project aims to reduce the cost and time of research by applying theory, modeling, and simulation to the most relevant bottlenecks in the biochemical process. We use molecular modeling, quantum mechanics, metabolic modeling, fluid dynamics, and reaction-diffusion methods in close collaboration with pretreatment, hydrolysis, upgrading, and TEA. The project's outcomes are increased yields and efficiency of the biochemical process, added value to products, and reduced price of fuels by specifically targeting catalytic efficiency, reactor design, enzyme efficiency, and microbial design. We work closely with experimental projects to identify problems and iterate with experiments to find and refine solutions. By working with experimentalists, we decide on problems that can be solved with simulation that could otherwise not be solved or would take too long with experiment alone to reach BETO's targets. Over the years, we have produced solutions that have resulted in determining the most likely fatty-acid derivative for passive transport out of bacteria that upgrade biomass, and we have also designed enzyme mutations for enhanced lignin upgrading. Metabolic models have been developed to tune the activity of 2,3 butanediol production for the 2030 target. A computational method to deliver understanding of how complex omics data can be interpreted in the metabolic pathways of organisms used in the Agile Biofoundry. We have found methods to overcome specific barriers and continue to develop those methods. Our reactor studies have guided the design of both the microbes and reactors for aerobic and micro-aerobic production at all scales and have been instrumental in improving the accuracy of techno-economic analysis models. This project is essential in the process of selecting the final processes for 2030 SAF production targets. More specifically, recently, we have: 1) Predicted the strength of the basic structural interactions in commodity plastics to provide guidance for plastics upcycling strategies. 2) Developed computational tool to improve the characterization of lignin-derived compounds 3) Developed new methodologies to enable Machine Learning-based Directed Evolution for protein engineering. 4) Developed Machine Learning methods to predict protein promiscuity and mutations to further improve microbial and enzymatic driven processes and demonstrated the utility of ML approaches to engineering proteins from sparse experimental datasets. 5) Developed new methods to enable high-fidelity simulation of aerobic fermentation at industrial scale and resolving mismatch of time scales through subcycling/operator splitting 7) Identified the difficulty in preventing local high-oxygen conditions in industrial bubble columns, which leads to less-desirable acetoin production, suggesting future research directions in alternative reactor configurations (e.g loop reactors, shallow-channel reactors).

BIOMASS FUELS↗

DOE OSTI2021

Study the existing form of copper ( p-type oxide/segregation ) and its release mechanism from the passive film of Ti-7Cu alloy

For this work, the existing form of copper and its release mechanism from the passive film of Ti-7Cu alloy was studied by Quantitative analysis of depth profile and series of electrochemical tests. Results were interpreted within the Point Defect Model-II. Copper does not form any p-type (cuprous or cupric) oxide but preferentially oxidises at the metal/film interface and segregated as Cu interstitials ($Cu^+_i$) and become substituted as $Cu^{x'}_{Ti}$ in the oxygen-deficient TiO 2-x barrier layer having n-type semiconducting character. Eventually, the segregated species of Cu preferentially dissolute through the film as Cu ions into the solution at film/solution interface via the Esaki-tunnelling effect.

Siddiqui, Muhammad Ali↗

DOE OSTI2026

Measurement of low energy characteristic X-rays emitted present in U-10Mo HALEU alloy fuel

Advance high density monolithic alloy HALEU fuels have been scanned with a silicon drift detector scanning system to measure low-energy characteristic X-rays emitted by uranium daughters, as well as zirconium present as a foil diffusion barrier. Four peaks were measured across the surfaces of three plates, and are consistent with other thorium and protactinium peaks present in depleted uranium samples that are induced by the decay of 235 U and 238 U. Of the four peaks detected, three are dominated by the decay of 235 U, and one peak at 15.70 keV covers two characteristic X-rays from the zirconium diffusion barrier (Kα 1 ) and from a 231 Th 15.62 keV X-ray induced by 235 U α-decay. The low energies of these lines suggest that they are mostly emitted from the fuel meat surface, and the poor counting statistics caused by strong self-attenuation make these data a poor candidate for 235 U/ 238 U ratio analysis. We suggest, then, that these X-rays could be used for passive measurement of variations in the cladding thickness of these fuels to complement manual thickness measurement methods.

HALEU↗