Search NASA⌕ Search

SEARCH · Search NASA

Results for “reaction sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Ultrahigh temperature in situ transmission electron microscopy based bicrystal coble creep in Zirconia II: Interfacial thermodynamics and transport mechanisms

This work uses a combination of stress dependent single grain boundary Coble creep and zero-creep experiments to measure interfacial energies, along with grain boundary point defect formation and migration volumes in cubic ZrO 2 . These data, along with interfacial diffusivities measured in a companion paper are then applied to analyzing two-particle sintering. The analysis presented here indicates that the large activation volume, v * = v f + v m primarily derives from a large migration volume and suggests that the grain boundary rate limiting defects are delocalized, possibly due to electrostatic interactions between charge compensating defects. The discrete nature of the sintering and creep process observed in the small-scale experiments supports the hypothesis that grain boundary dislocations serve as sources and sinks for grain boundary point defects and facilitate strain during sintering and Coble creep. Model two-particle sintering experiments demonstrate that initial-stage densification follows interface reaction rate-limited kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Chrome-free qandilite (Mg 2 TiO 4 ) refractory aggregates: Role of titania source and evaluation of thermal expansion coefficient

As used chrome-based refractories may contain toxic Cr 6+ , the chrome-free Mg 2 TiO 4 phase is being considered which is known to improve hot strength and resistance to thermal shock and slag corrosion. As in situ Mg 2 TiO 4 formation generates porosity, preformed aggregates are desirable. Dilatometric studies revealed that when dead burned magnesia is combined with industrial anatase instead of rutile, it expanded less (1% versus 7.2%) and the reaction occurred earlier (965°C compared to 1120°C). After sintering at 1,600°C, rutile produced an aggregate with 3.8% open porosity, whereas anatase led to 0 % porosity and a bulk density of 3.24g/cm 3 with a thermal expansion coefficient (70–1,600°C) of 13.5×10 -6 K -1 . Moreover, replacing rutile by anatase eliminates the undesirable MgTiO 3 phase. The anatase-based aggregate consisted of a Mg 2 TiO 4 matrix with residual unreacted MgO and an intergranular, refractory CaTiO 3 phase. In conclusion, the rutile-based aggregate was deemed unsuitable due to a low-melting microstructure of forsterite contiguous with CaTiO 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Intra-crystalline mesoporous zeolite encapsulation-derived thermally robust metal nanocatalyst in deep oxidation of light alkanes

Zeolite-confined metal nanoparticles (NPs) have attracted much attention owing to their superior sintering resistance and broad applications for thermal and environmental catalytic reactions. However, the pore size of the conventional zeolites is usually below 2 nm, and reactants are easily blocked to access the active sites. Herein, a facile in situ mesoporogen-free strategy is developed to design and synthesize palladium (Pd) NPs enveloped in a single-crystalline zeolite (silicalite-1, S-1) with intra-mesopores (termed Pd@IM-S-1). Pd@IM-S-1 exhibited remarkable light alkanes deep oxidation performances, and it should be attributed to the confinement and guarding effect of the zeolite shell and the improvement in mass-transfer efficiency and active metal sites accessibility. The Pd–PdO interfaces as a new active site can provide active oxygen species to the first C–H cleavage of light alkanes. This work exemplifies a promising strategy to design other high-performance intra-crystalline mesoporous zeolite-confined metal/metal oxide catalysts for high-temperature industrial thermal catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Phase evolution during conventional and reactive flash sintering of (Mg,Ni,Co,Cu,Zn)O via in situ X-ray diffraction

Reactive flash sintering (RFS) enables the simultaneous synthesis and sintering of ceramics and has been shown to affect the reaction pathway of different materials. Herein, in situ synchrotron X-ray diffraction (XRD) is used to investigate the (Mg,Ni,Co,Cu,Zn)O entropy-stabilized oxide formation during: (i) conventional heating and (ii) RFS under current rate-controlled mode. The same reaction pathway is verified in both instances: the starting rock-salt (RS), spinel (Co 3 O 4 ), tenorite (CuO), and wurtzite (ZnO) phases transform into a single RS phase with a (1 1 1) to (2 0 0) intensity ratio of 0.67, consistent with a random distribution of the cations into the structure. Pt lattice peak shift from the XRD patterns is used as standard to monitor the sample surface temperature, revealing a strong endothermic reaction during the RS single-phase formation (Pt peaks shift toward higher angles while increasing sample temperature/current density). Furthermore, in RFS, the single-phase RS structure is formed in just 60 s at a furnace temperature of 600°C and a current rate of 220 mA mm -2 /min. Therefore, RFS greatly accelerates the synthesis of (Mg,Ni,Co,Cu,Zn)O, however, it does not play a role in the reaction pathway for this material formation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Nonprecious Single Atom Catalyst for Methane Pyrolysis

The development of a suitable catalytic system for methane pyrolysis reactions requires a detailed investigation of the activation energy of C-H bonds on catalysts, as well as their stability against sintering and coke formation. In this work, both single-metal Ni atoms and small clusters of Ni atoms deposited on titanium nitride (TiN) plasmonic nanoparticles were characterized for the C-H bond activation of a methane pyrolysis reaction using ab initio spin-polarized density functional theory (DFT) calculations. The present work shows the complete reaction pathway, including energy barriers for C-H bond activation and dehydrogenated fragments, during the methane pyrolysis reaction on catalytic systems. Interestingly, the C-H bond activation barriers were low for both Ni single-atom and Ni-clusters, showing the energy barriers of ~1.10 eV and ~0.88 eV, respectively. Additionally, single-atom Ni-TiN showed weaker binding to adsorbates, and a net endothermic reaction pathway indicated that the single-atom Ni-TiN was expected to resist coke formation on its surface. However, these Ni single-atom catalysts can sinter, aggregate into a small cluster, and form a coke layer from the highly exothermic reaction pathway that the cluster takes despite the facile reaction pathway.

08 HYDROGEN↗
NASA NTRS1989

Measurement of interfacial shear strength in SiC-fiber/Si3N4 composites

An indentation method for measuring shear strength in brittle matrix composites was applied to SiC-fiber/Si3N4-matrix samples. Three methods were used to manufacture the composites: reaction bonding of a Si/SiC preform, hot-pressing, and nitrogen-overpressure sintering. An indentation technique developed by Marshall for thin specimens was used to measure the shear strength of the interface and the interfacial friction stresses. This was done by inverting the sample after the initial push through and retesting the pushed fibers. SEM observations showed that the shear strength was determined by the degree of reaction between the fiber and the matrix unless the fiber was pushed out of its (well-bonded) sheath.

Laughner, James W.↗
DOE OSTI2022

Nitrogen-doped carbon for selective pseudo-metal-free hydrodeoxygenation of 5-hydroxymethylfurfural to 2,5-dimethylfuran: Importance of trace iron impurity

Heteroatoms-doped carbon materials have recently emerged as effective catalysts for various chemical and electrochemical reactions. The free of metals especially noble metals reduces cost and eliminates issues like sintering or leaching of metals at elevated temperatures in solvents. In this work, selective hydrodeoxygenation (HDO) of 5-hydroxymethylfurfural (HMF) to 2,5-dimethylfuran (DMF) is for the first time achieved over simple nitrogen-doped carbon (N-C) catalysts. Further, at optimal reaction conditions, a 91% yield of DMF is obtained with excellent catalyst stability. Extensive characterization, including extended X-ray absorption fine-structure (EXAFS) and soft X-ray absorption spectroscopy (sXAS), model reactions, basic data science analysis, and DFT calculations suggest that ppm of Fe in particular FeN 3 sites formed in pyrolysis, rather than non-metallic elements, drive key steps such as H 2 activation and deoxygenation of –OH during HMF HDO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Ink Casting and 3D‐Extrusion Printing of Yb 14 MnSb 11 for High‐Temperature Thermoelectric Material

Abstract Complex shapes are created from Yb 14 MnSb 11 , a high‐temperature thermoelectric Zintl phase, via a two‐step process: i) layer‐by‐layer 3D‐extrusion of ink containing partially‐reacted powders which are ball‐milled from a blend of Yb, MnSb, and Sb powders; ii) heat treatment to synthesize the ternary compound Yb 14 MnSb 11 and densify the extruded powders. A high phase purity for Yb 14 MnSb 11 (83–94%) is achieved in both cast and 3D‐extruded ink specimens via a solid‐state reaction between Yb, MnSb, and Yb 4 Sb 3 during reactive sintering. Pressure‐free sintering at temperatures of 1200–1400 °C densifies the powders to 82% relative density but can also induce the decomposition of the Yb 14 MnSb 11 phase due to Yb sublimation. A process window with optimized sintering temperature and time is identified, achieving both low porosity and high phase purity and reaching a maximum zT = 0.61 at 1000 °C, about half of the maximum zT value for bulk Yb 14 MnSb 11 made via conventional processes (pressure sintering of precursor powders). The present approach – direct ink writing of ball‐milled powders, combined with reactive sintering – is a scalable and affordable method to fabricate thermoelectric legs with intricate 3D shapes, for enhanced performances in high‐temperature thermoelectric applications.

Chen, Ming [Department of Materials Science &amp, ↗
NASA NTRS1991

Thermochemical analysis of chemical processes relevant to the stability and processing of SiC-reinforced Si3N4 composite

Chemical processes relevant to the stability and processing of SiC-reinforced Si3N4 composites have been examined from thermochemical considerations. The thermodynamic stabilities of various interfaces, such as SiC-Si3N4, SiC-Si3N4-Si2ON2, and SiC-Si3N4-SiO2, have been examined as a function of temperature, and the temperatures above which these interfaces become unstable have been calculated. The degradation of SiC during the processing of the composite has been examined. The processing routes considered in this study include the reaction bonded silicon nitride (RBSN) process and the pressure-assisted sintering processes with suitable sintering additives.

Misra, Ajay K.↗
NASA NTRS1993

Push-out tests on a new silicon carbide/reaction-bonded silicon carbide ceramic matrix composite

Fiber push-out tests have been performed on a ceramic matrix composite consisting of carborundum-sintered SiC fibers, with a BN coating, embedded in a reaction-bonded SiC matrix. Analysis of the push-out data, utilizing the most complete theory presently available, shows that one of the fiber/coating/matrix interfaces has a low fracture energy (one-tenth that of the fiber) and a moderate sliding resistance of about 8 MPa. The debonded sliding interface shows some continuous but minor abrasion, which appears to increase the sliding resistance, but overall the system exhibits very clean smooth sliding. The tensile response of a full-scale composite is then modeled using data obtained here and known fiber strengths to demonstrate the good composite behavior predicted for this material.

Curtin, William A.↗
DOE OSTI2022

U Metal Oxidation with Steam (U)

The Savannah Rive National Laboratory 9SRNL) is evaluating a method to produce uranium oxide (UO 2 ) from uranium metal using steam. The typical methods for making UO 2 yield powders with particle-size ranges of 1 to 50 micron. The goal of the steam oxidation is to produce a depleted uranium (DU) product with a larger particle size that can be used as a surrogate for testing physical and mechanical process techniques to refine uranium and/or plutonium bearing residues. Several studies in the literature indicated that reactions between uranium metal and steam will yield UO 2 as fine powders in the 160 to 500 °C range, but granular materials form above 500°C. Above 880 °C, a hard compact scale forms on the U metal. Furthermore, sintering of UO 2 occurs at about 1300 °C, but it has been stated that the presence of steam enhances the sintering characteristics of UO 2 . Initial studies into the oxidation of DU metal in an atmosphere of argon and steam have been completed. Oxidation of depleted uranium metal in Ar/steam at 600, 710, 700, and 830 °C yielded at UO 2 product with little or no impurity at each temperature. Although not enough sample was available to perform sieve analysis for particle size distribution, SEM images reveal that a significant volume fraction of the products at 710, 770, and 830 °C exceeds 100 microns. The material produced at 600 °C was too fine for programmatic needs. Questions associated with the UO 2 include morphology of product, mechanical strength of the particles, and performance in milling operations. The size of the samples produced in these tests did not allow for quantitative assessment of particle size of mechanical strength. A qualitative assessment of the particles formed at 710, 770, and 830 °C was that the samples produced at 710 and 770 °C were friable, and the sample produced 830 °C had more mechanical strength. Sintering of the samples in Ar/steam at 970 °C appeared to increase the strength of the particles without changing their general particle size characteristics. Due to the small sample sizes, the increase in strength could not be quantified. If the sintering at 970 °C is inadequate, higher sintering temperatures in Ar/steam can be evaluated. Future work will increase scale of the steam oxidation conditions which yield the most-favorable particle-size distributions with sufficient mechanical strength for programming usage. Further consideration will be given to oxidation temperature, steam addition to the reaction vessel, U metal pretreatment, and sintering conditions after oxidation. The UO 2 production could involve a two-step process where particles are formed in steam at lower temperatures (700-850 °C) and then sintered in Ar/steam at elevated temperatures (950-1200 °C). Larger samples (50-100 g each) will provide sufficient UO 2 product for sieve analysis and assessment of mechanical strength relatives to subsequent milling operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Synthesis of Hf 6 Ta 2 O 17 superstructure via spark plasma sintering for improved oxidation resistance of multi-component ultra-high temperature ceramics

Ultra-high temperature ceramics (UHTCs) have shown aspiration to overcome challenges in the thermal protection system (TPS) by designing new materials referred to as multi-component UHTCs (MC-UHTCs) in the compositional space. MC-UHTCs have shown remarkable improvement in oxidation resistance due to the formation of the Hf6Ta2O17 superstructure during plasma exposure. Herein, the Hf 6 Ta 2 O 17 superstructure is synthesized via a solid-state reaction between HfO 2 and Ta 2 O 5 powder mixtures during spark plasma sintering (SPS). The compositions chosen are 50 vol% of HfO 2 -50 vol% of Ta 2 O 5 (50HO-50TO) and 70 vol% of HfO 2 -30 vol% of Ta 2 O 5 (70HO-30TO). The phase quantification via Rietveld analysis showed Hf 6 Ta 2 O 17 as a principal phase with some residual Ta 2 O 5 phase in both the samples. The high-temperature thermal stability of the samples was evaluated using high-velocity plasma jet exposure for up to 3 min. 50HO-50TO was able to withstand the intense plasma condition, which is attributed to the higher content of the Hf 6 Ta 2 O 17 phase (~84%) and lower strain in the Ta 2 O 5 phase. The augmentation in the Hf 6 Ta 2 O 17 phase to 94.7% (in 50HO-50TO) post plasma exposure has been attributed to the invariant transformation from a liquid state to Hf 6 Ta 2 O 17 at temperatures >2500 °C during testing. The mechanical integrity is elucidated from the insignificant change in the hardness ~13.3 GPa before and 11.2 GPa after plasma exposure of the 50HO-50TO sample. As a result, the Hf 6 Ta 2 O 17 superstructure's thermo-mechanical stability suggests developing novel oxidation-resistant MC-UHTCs in compositional space for reusable space vehicle applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermally Driven Interfacial Degradation between Li 7 La 3 Zr 2 O 12 Electrolyte and LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode

Solid-state batteries offer higher energy density and enhanced safety compared to the present lithium-ion batteries using liquid electrolytes. A challenge to implement them is the high resistances, especially at the solid electrolyte interface with the cathode. Sintering at elevated temperature is needed in order to get good contact between the ceramic solid electrolyte and oxide cathodes and thus to reduce contact resistances. Many solid electrolyte and cathode materials react to form secondary phases. It is necessary to find out which phases arise as a result of interface sintering and evaluate their effect on electrochemical properties. Herein, we assessed the interfacial reactions between LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) and Li 7 La 3 Zr 2 O 12 (LLZO) as a function of temperature in air. We prepared model systems by depositing thin-film NMC622 cathode layers on LLZO pellets. The thin-film cathode approach enabled us to use interface-sensitive techniques such as X-ray absorption spectroscopy in the near-edge as well as the extended regimes and identify the onset of detrimental reactions. We found that the Ni and Co chemical environments change already at moderate temperatures, on-setting from 500 °C and becoming especially prominent at 700 °C. By analyzing spectroscopy results along with X-ray diffraction, we identified Li 2 CO 3 , La 2 Zr 2 O 7 , and La(Ni,Co)O 3 as the secondary phases that formed at 700 °C. The interfacial resistance for Li transfer, measured by electrochemical impedance spectroscopy, increases significantly upon the onset and evolution of the detected interface chemistry. Our findings suggest that limiting the bonding temperature and avoiding CO 2 in the sintering environment can help to remedy the interfacial degradation.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Surface Cracking and Interface Reaction Associated Delamination Failure of Thermal and Environmental Barrier

In this paper, surface cracking and interface reactions of a ZrO2-8wt%Y2O3 and mullite/BSAS/Si thermal and environmental barrier coating system on SiC/SiC ceramic matrix composites were characterized after long-term combined laser thermal gradient and furnace cyclic tests in a water vapor containing environment. The surface cracking was analyzed based on the coating thermal gradient sintering behavior and thermal expansion mismatch stress characteristics under the thermal cyclic conditions. The interface reactions that were largely enhanced by the coating surface cracking in the water vapor environment were investigated in detail, and the reaction phases were identified for the coating system after the long-term exposure. The accelerated coating delamination failure was attributed to the increased delamination driving force under the thermal gradient cyclic loading and the reduced interface adhesion due to the detrimental interface reactions. The coating design issues will also be discussed based on the observed failure mechanisms under the high-heat-flux test conditions.

Zhu, Dongming↗
DOE OSTI2023

Dynamic Tracking of NiFe Smart Catalysts using In Situ X-Ray Absorption Spectroscopy for the Dry Methane Reforming Reaction

The exsolution of nanoparticles from perovskite precursors has been explored as a route to synthesize catalysts with sinter or coke resistance. The characteristics of these exsolved nanoparticles are highly dynamic depending on the redox nature of the environment to which they are subjected. To develop their properties for thermo- and electrocatalytic applications, it is necessary to track the states and behavior of exsolved catalysts with in situ and ex situ characterization. In this study, we conduct in situ X-ray absorption spectroscopy (XAS) along with ex situ scanning transmission electron microscopy high-angle annular dark-field (STEM-HAADF) and energy-dispersive X-ray spectroscopy analysis of the parent perovskite oxide precursor, LaFe 0.8 Ni 0.2 O 3 , as its structure forms bimetallic NiFe nanoparticles and evolves in oxidative, reductive, and dry methane reforming environments. We develop a theory that NiFe exsolution is a function of the reduction potential where LaFe 0.8 Ni 0.2 O 3 transforms to NiFe alloy supported on LaO x -LaFeO x . The Ni starts to exsolve at 268 °C, while most Fe exsolves at 700 °C. During dry methane reforming conditions, most of the Fe is oxidized by CO 2 during the reaction and re-enters the perovskite as LaFeO 3 , while Ni remains on the surface as nanoparticles in the metallic state. During the oxidative regeneration phase, most of the Fe re-enters the bulk perovskite phase, while Ni is partially regenerated with a small percentage oxidized to large NiO nanoparticles. Finally, this study sheds light on the exsolution and regeneration of bimetallic alloy nanoparticles and the influence of the reaction conditions on their catalyst performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2003

Surface Cracking and Interface Reaction Associated Delamination Failure of Thermal and Environmental Barrier Coatings

In this paper, surface cracking and interface reactions of a BSAS coating and a multi-layer ZTO2-8wt%Y2O3 and mullite/BSAS/Si thermal and environmental barrier coating system on SiC/SiC ceramic matrix composites were characterized after long-term combined laser thermal gradient and furnace cyclic tests in a water vapor containing environment. The surface cracking was analyzed based on the coating thermal gradient sintering behavior and thermal expansion mismatch stress characteristics under the thermal cyclic conditions. The interface reactions, which were largely enhanced by the coating surface cracking in the water vapor environment, were investigated in detail, and the reaction phases were identified for the coating system after the long- term exposure. The accelerated coating delamination failure was attributed to the increased delamination driving force under the thermal gradient cyclic loading and the reduced interface adhesion due to the detrimental interface reactions.

Zhu, Dongming↗
NASA NTRS2003

Surface Cracking and Interface Reaction Associated Delamination Failure of Thermal and Environmental Barrier Coatings

In this paper, surface cracking and interface reactions of a BSAS coating and a multi-layer ZrO2-8wt%Y2O3 and mullite/BSAS/Si thermal and environmental barrier coating system on SiC/SiC ceramic matrix composites were characterized after long-term combined laser thermal gradient and furnace cyclic tests in a water vapor containing environment. The surface cracking was analyzed based on the coating thermal gradient sintering behavior and thermal expansion mismatch stress characteristics under the thermal cyclic conditions. The interface reactions, which were largely enhanced by the coating surface cracking in the water vapor environment, were investigated in detail, and the reaction phases were identified for the coating system after the long-term exposure. The accelerated coating delamination failure was attributed to the increased delamination driving force under the thermal gradient cyclic loading and the reduced interface adhesion due to the detrimental interface reactions.

Zhu, Dong-Ming↗