Search NASA⌕ Search

SEARCH · Search NASA

Results for “science measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Compositional and phase dependence of elastic modulus of crystalline and amorphous Hf 1- x Zr x O 2 thin films

The elastic moduli of amorphous and crystalline atomic layer-deposited Hf 1-x Zr x O 2 (HZO, x = 0, 0.31, 0.46, 0.79, 1) films prepared with TaN electrodes on silicon substrates were investigated using picosecond acoustic measurements. The moduli of the amorphous films were observed to increase between 211 ± 6 GPa for pure HfO 2 and 302 ± 9 GPa for pure ZrO 2 . In the crystalline films, it was found that the moduli increased upon increasing the zirconium composition from 248 ± 6 GPa for monoclinic HfO 2 to 267 ± 9 GPa for tetragonal ZrO 2 . Positive deviations from this increase were observed for the Hf 0.69 Zr 0.31 O 2 and Hf 0.54 Zr 0.46 O 2 compositions, which were measured to have moduli of 264 ± 8 GPa and 274 ± 8 GPa, respectively. These two compositions contained the largest fractions of the ferroelectric orthorhombic phase, as assessed from polarization and diffraction data. The biaxial stress states of the crystalline films were characterized through sin 2 (ψ) x-ray diffraction analysis. The in-plane stresses were all found to be tensile and observed to increase with the increasing zirconium composition, between 2.54 ± 0.6 GPa for pure HfO 2 and 5.22 ± 0.5 GPa for pure ZrO 2 . The stresses are consistent with large thermal expansion mismatches between the HZO films and silicon substrates. Furthermore, these results demonstrate a device-scale means to quantify biaxial stress for investigation on its effect on the ferroelectric properties of hafnia-based materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Retrieval of Cloud Liquid Water Using Microwave Signals from LEO Satellites: A Feasibility Study through Simulations

A novel method, using low Earth orbit (LEO) satellite microwave communication links for cloud liquid water measurements, is introduced in this paper. The feasibility of this approach is studied through simulations of the retrieval system including a LEO satellite communicating with a group of ground receivers equipped with signal-to-noise ratio (SNR) estimators, a synthetic cloud attenuation field and a tomographic retrieval algorithm. Rectangular and Gaussian basis functions are considered to define the targeted field. Simulation results suggest that the proposed least-squares based retrieval algorithm produces satisfactory outcomes for both types of basis functions. The root-mean-square error of the retrieved field is around 0.2 dB/km, with the range of the reference field as 0 to 2.35 dB/km. It is also confirmed that the partial retrieval of the cloud field is achievable when a limited number of receivers with restricted locations are available. The retrieval outcomes exhibit properties of high resolution and low error, indicating that the proposed approach has great potential for cloud observations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Cloud Type and Life Stage Dependency of Liquid–Ice Mass Partitioning in Mixed-Phase Clouds

This paper analyzes the temperature, cloud type, and life stage dependencies of phase partitioning in mixed-phase clouds spanning tropics, midlatitudes, and the Arctic, using data from ground-based remote sensing measurements in Alaska and aircraft measurements from three field campaigns. The results show: (1) The liquid fraction in Arctic stratiform clouds decreased from 1 to 0.6 between 0 °C and −30 °C and was lower in spring because of the higher dust occurrence in Barrow, Alaska; (2) In wintertime orographic clouds, the liquid fraction was greater than 0.8; (3) Phase partitioning in convective clouds varied significantly with life stages. In the developing stage, it decreased from 1 to 0.3 between −5 °C and −15 °C, indicating rapid ice generation, while at the mature and dissipating stages, the liquid fractions were lower; (4) The stratiform regions of mesoscale convective systems were dominated by ice, with liquid fractions lower than 0.2; and (5) The variability of phase partitioning varied for different cloud types. In stratiform clouds, liquid dominated at warm temperatures. As the temperature decreased, an ice-dominated region was more frequently observed, while the occurrence of the mixed-phase region remained low. For convective clouds, the variability of phase partitioning was controlled by continuous glaciation with decreasing temperature and life cycle.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Resilience of electric utilities during the COVID-19 pandemic in the framework of the CIGRE definition of Power System Resilience

Resilience is a vital concept in engineering, business, and natural sciences, and is a measure of the ability of an entity to withstand High Impact Low Probability (HILP) events. During the COVID-19 pandemic, which started in late 2019/early 2020, power system utilities around the globe have responded in effective and efficient ways to enhance the resilience of their organisations, both in terms of real-time operations and prudent management of its infrastructure, in order to continue their mandate in providing reliable supply to meet customer demands. Here, this paper presents the CIGRE definition for power system resilience, established by the C4.47 Working Group in 2018, and demonstrates the application of resilience-oriented thinking within the electrical sector. The response and recovery efforts are described, with respect to the key actionable measures integral to the power system resilience definition, taken before, during and after the COVID-19 pandemic. A practical conceptual framework is also presented for thinking about resilience in terms of three key components of resilience strategies: organisational, infrastructure and operational resilience. The paper also discusses the different strategies adopted in response to COVID-19, based on the C4.47 members’ experiences during the pandemic. Finally, a case study is presented, which proves the effectiveness of a set of response measures, using graph theory and the characteristics of the staff-asset interactions.

42 ENGINEERING↗
DOE OSTI2020

Magnetic and mechanical properties of grain-refined Dy-free Nd-Fe-B sintered magnets

In this work, the effects of grain size on magnetic and mechanical properties of Dy-free Nd-Fe-B sintered magnets were studied. The grain size of the sintered magnets was varied by using different sized Dy-free Nd-Fe-B alloy feedstock powders which were ball milled to different extents. Increasing the ball milling time from 7 to 11 h caused the average particle size of the powders to decrease from 3.6 to 2.1 µm, while the average grain size of the corresponding sintered magnets decreased from 5.0 to 4.0 µm. The intrinsic coercivity Hcj and maximum energy product (BH) max of these magnets increased from 11.6 to 13.7 kOe and 41.6 to 43.6 MGOe, respectively. The finer grain magnets exhibited better thermal stability, as indicated by a smaller temperature coefficient of H cj (-0.71%/°C). With extending ball milling time to 15 h, the magnetic properties of the magnets deteriorate, while the flexural strengths first decrease and then increase. The flexural strength improvement is attributed to the increased Oxygen content in the magnets due to finer grains. The coercivity enhancement by reduction of grain size is a promising approach to develop Dy-free Nd-Fe-B sintered magnets with better thermal stability. It is important to control the Oxygen contents in the magnets to compromise both magnetic and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Reduction of detection limit and quantification uncertainty due to interferent by neural classification with abstention

Many measurements in the physical sciences can be cast as counting experiments, where the number of occurrences of a physical phenomenon informs the prevalence of the phenomenon's source. Often, detection of the physical phenomenon (termed signal) is difficult to distinguish from naturally occurring phenomena (termed background). In this case, the discrimination of signal events from background can be performed using classifiers, and they may range from simple, threshold-based classifiers to sophisticated neural networks. These classifiers are often trained and validated to obtain optimal accuracy, however we show that the optimal accuracy classifier does not generally coincide with a classifier that provides the lowest detection limit, nor the lowest quantification uncertainty. Here, we present a derivation of the detection limit and quantification uncertainty in the classifier-based counting experiment case. We also present a novel abstention mechanism to minimize the detection limit or quantification uncertainty a posteriori. We illustrate the method on two data sets from the physical sciences, discriminating Ar-37 and Ar-39 radioactive decay from non-radioactive events in a gas proportional counter, and discriminating neutrons from gammas in an inorganic scintillator and report results therefrom.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Characterization of local parameters of inclined upward air–water bubbly two-phase flows in a round pipe

The present work seeks to develop a detailed experimental database and characterize the local effects of inclination on horizontal and upward bubbly air–water two-phase flows. Experimental conditions are selected to investigate bubbly flows at a variety of orientations while reducing the influence of flow regime transition. Detailed time-averaged data is collected using state-of-the-art four-sensor conductivity probes for measurements across the flow area for five flow conditions at five inclination orientations in a 25.4 mm inner diameter pipe. Using the newly established database, effects of inclination on bubbly flows are analyzed, as are changes in liquid and gas flow rate at different orientations. The observations include (1) bubble migration and agglomeration at the top pipe wall as orientation changes from vertical to horizontal; (2) reducing the angle from vertical reduces the local gas velocity, and correspondingly reduces the global slip from greater than unity at 90° to less than unity for 60° and lower; (3) changes in the bubble size distribution are primarily at the interface between the bubble cluster and the liquid region of the pipe, not coalescence within the bubble cluster. In conclusion, physical mechanisms for these observations are proposed, and the present trends at different orientations support previous experiments in horizontal two-phase flows.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Two-phase flow measurements and observations in a cooling panel of the reactor cavity cooling system

The analysis of the flow behavior within a cooling panel of a scaled water-cooled reactor cavity cooling system has been performed supported by high-resolution measurements of the void fraction at the risers’ outlet. The results have shown a stable, symmetric distribution of the flow through the risers during subcooled boiling conditions, characterized by small, slow bubbles with average void fraction lower than 0.3 for all risers. As the temperature increased to saturation, flow distribution appeared strongly asymmetrical and unstable, with peaks of void fraction as high as 0.9. Large, faster bubbles were observed during these peaks, immediately followed by flow of subcooled liquid water. Flow stagnation and inversion has also been observed. The high resolution void fraction results, complemented by the measurements of the coolant flow rate and temperatures, not only have further described the behavior of the system under hypothetical accident conditions, but represent a unique set of data to support the validation of system-level codes, and more advanced computational tools.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Optical Cycling Functionalization of Arenes

Closed, laser-induced optical transitions (“optical cycling transitions”) of molecules can be used for state preparation and measurement in quantum information science and quantum sensing. Increasingly complex molecular species supporting optical cycling can provide new capabilities for quantum science, and it is not clear if there is a limit on their size or complexity. We explore Ca–O–L molecular constructs to support the optical cycling center, Ca, with ligands, L, being arenes. We find that L can be as large as coronene (i.e., CaOC 24 H 11 ) without losing the diagonality of the Franck–Condon factor (FCF). Furthermore, L can be substituted with electron-withdrawing groups to improve the FCF. Larger L, beyond ~7 rings, can disrupt the diagonality of the FCF by closing the HOMO–LUMO ligand electronic state gap and reordering with the local states on the cycling center. Altogether, we find that optical cycling can be retained for arenes, and we offer a principle for their design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Quantum algorithm for electronic band structures with local tight-binding orbitals

While the main thrust of quantum computing research in materials science is to accurately measure the classically intractable electron correlation effects due to Coulomb repulsion, designing optimal quantum algorithms for simpler problems with well-understood solutions is a useful tactic to advance our quantum “toolbox”. With this in mind, we consider the quantum calculation of a periodic system’s single-electron band structure over a path through reciprocal space. Previous efforts have used the Variational Quantum Eigensolver algorithm to solve the energy of each band, which involves numerically optimizing the parameters of a variational quantum circuit to minimize a cost function, constructed as the expectation value of a Hamiltonian operator. Traditionally, a unique Hamiltonian operator is constructed for each k-point, so that many cost functions, each with their own parameter space, must be optimized to generate a single band. Similarly, calculating higher bands than the first has traditionally involved modifying the cost function with additional overlap terms to ensure higher-energy eigenstates are orthogonal to those of lower bands. In this paper, we adopt a direct space approach, using a novel hybrid first/second-quantized qubit mapping which allows us to construct a single Hamiltonian, and a single cost-function, suitable for solving the entire electronic band structure. In contrast to previous approaches, the k-point and the band index are selected by additional parameters in our quantum circuit, rather than through modifications to the cost function. The result is a technically and conceptually simpler approach to band structure calculations on a quantum computer. Moreover, we expect that the tools developed herein will motivate new strategies for tackling highly-correlated materials beyond the grasp of classical computing.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Adaptively controlled fast production of defect-free beryllium ion crystals using pulsed laser ablation

Trapped atomic ions find wide applications ranging from precision measurement to quantum information science and quantum computing. Beryllium ions are widely used due to the light mass and convenient atomic structure of beryllium; however, conventional ion loading from thermal ovens exerts undesirable gas loads for a prolonged duration. Here, we demonstrate a method to rapidly produce pure linear chains of beryllium ions with pulsed laser ablation, serving as a starting point for large-scale quantum information processing. Our method is fast compared to thermal ovens, reduces the gas load to only 10 -12 Torr (10 -10 Pa) level, yields a short recovery time of a few seconds, and also eliminates the need for a deep ultraviolet laser for photoionization. We also study the loading dynamics, which show non-Poissonian statistics in the presence of sympathetic cooling. In addition, we apply feedback control to obtain defect-free ion chains with desirable lengths.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Photochemistry sample sticks for inelastic neutron scattering

Every material experiences atomic and molecular motions that are generally termed vibrations in gases and liquids or phonons in solid state materials. Optical spectroscopy techniques, such as Raman, infrared absorption spectroscopy, or inelastic neutron scattering (INS), can be used to measure the vibrational/phonon spectrum of ground state materials properties. A variety of optical pump probe spectroscopies enable the measurement of excited states or elucidate photochemical reaction pathways and kinetics. So far, it has not been possible to study photoactive materials or processes in situ using INS due to the mismatch between neutron and photon penetration depths, differences between the flux density of photons and neutrons, cryogenic temperatures for INS measurements, vacuum conditions, and a lack of optical access to the sample space. These experimental hurdles have resulted in very limited photochemistry studies using INS. Here we report on the design of two different photochemistry sample sticks that overcome these experimental hurdles to enable in situ photochemical studies using INS, specifically at the VISION instrument at Oak Ridge National Laboratory. We demonstrate the use of these new measurement capabilities through (1) the in situ photodimerization of anthracene and (2) the in situ photopolymerization of a 405 nm photoresin using 405 nm excitation as simple test cases. Furthermore, these new measurement apparatus broaden the science enabled by INS to include photoactive materials, optically excited states, and photoinitiated reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Studies of the weak interaction in atomic systems: towards measurements of atomic parity non-conservation in francium

Abstract Tests of the standard model of particle physics should be carried out over the widest possible range of energies. Here we present our plans and progress for an atomic parity non-conservation experiment using the heaviest alkali, francium ( Z = 87), which has no stable isotope. Low-energy tests of this kind have sensitivity complementary to higher energy searches, e.g. at the large hadron collider.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2026

Uncovering Hidden Entanglement in Twin Beams

Proper characterization of quantum correlations in multimode optical quantum states is critical for applications in quantum information science. However, standard entanglement measurements can lead to incomplete state reconstruction and characterization. Here, we implement a resonator-based detection system that reveals entanglement between sideband modes of twin beams, achieving full tomography and retrieving often ignored quantum correlations. Unlike standard spectral measurements such as homodyne detection, resonator detection can independently address the sidebands of each beam, thereby accessing these hidden correlations. Additionally, we show how phase shifts between the carrier and the sideband modes of the involved fields redistribute information and modify the observation of entanglement for different witnesses. The ability of the resonant detection to independently address sideband modes of entangled states can contribute to enhancing the capacity for secure communication and quantum networking protocols.

Rincon Celis, Raul [University of Sao Paulo, Brazi↗
DOE OSTI2021

Nature of the magnetic stripes in fully oxygenated La 2 CuO 4+y

We present triple-axis neutron scattering studies of static and dynamic magnetic stripes in an optimally oxygen-doped cuprate superconductor, La 2 CuO 4+y , which exhibits a clean superconducting transition at T c = 42 K. Polarization analysis reveals that the magnetic stripe structure is equally represented along both of the tetragonal crystal axes and that the fluctuating stripes display significant weight for in-plane as well as out-of-plane spin components. Both static magnetic order as well as low-energy fluctuations are fully developed in zero applied magnetic field and the low-energy spin fluctuations at ℏω = 0.3 – 10 meV intensify on cooling. We interpret this as an indication that superconductivity and low-energy spin fluctuations coexist microscopically in spatial regions which are separated from domains with static magnetic order.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Electronegative metal dopants improve switching variability in Al 2 ⁢O 3 resistive switching devices

Resistive random-access memories are promising for nonvolatile memory and brain-inspired computing applications. High variability and low yield of these devices are key drawbacks hindering reliable training of physical neural networks. In this paper, we show that doping an oxide electrolyte, Al 2 ⁢O 3 , with electronegative metals makes resistive switching significantly more reproducible, surpassing the reproducibility requirements for obtaining reliable hardware neuromorphic circuits. Based on density functional theory calculations, the underlying mechanism is hypothesized to be the ease of creating oxygen vacancies in the vicinity of electronegative dopants due to the capture of the associated electrons by dopant midgap states and the weakening of Al-O bonds. These oxygen vacancies and vacancy clusters also bind significantly to the dopant, thereby serving as preferential sites and building blocks in the formation of conducting paths. Throughout this work, we validate this theory experimentally by implanting different dopants over a range of electronegativities in devices made of multiple alternating layers of Al 2 ⁢O 3 and WN and find superior repeatability and yield with highly electronegative metals, Au, Pt, and Pd. These devices also exhibit a gradual SET transition, enabling multibit switching that is desirable for analog computing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hybrid-Magnon Quantum Devices: Strategies and Approaches

Hybrid magnonics offers novel paths towards quantum information by utilizing the unique advantages of magnon excitations. We review two strategies of hybrid magnonics for advancing quantum computing, i.e., multi-magnon entanglement and nonreciprocal magnon transduction. We also present our efforts on low-damping magnetic materials, short-wavelength magnon transduction, and nanowire superconducting circuits.

36 MATERIALS SCIENCE↗