Search NASA⌕ Search

SEARCH · Search NASA

Results for “selective wetting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Gating of Hydrophobic Nanopores with Large Anions

In this report, understanding ion transport in nanoporous materials is critical to a wide variety of energy and environmental technologies, ranging from ion-selective membranes, drug delivery, and biosensing, to ion batteries and supercapacitors. While nanoscale transport is often described by continuum models that rely on a point charge description for ions and a homogeneous dielectric medium for the solvent, here, we show that transport of aqueous solutions at a hydrophobic interface can be highly dependent on the size and hydration strength of the solvated ions. Specifically, measurements of ion current through single silicon nitride nanopores that contain a hydrophobic-hydrophilic junction show that transport properties are dependent not only on applied voltage but also the type of anion. We find that in Cl - -contained solutions the nanopores only conducted ionic current above a negative voltage threshold. On the other hand, introduction of large polarizable anions, such as Br - and I - , facilitated the pore wetting, making the pore conductive at all examined voltages. Molecular dynamics simulations revealed that the large anions, Br - and I - , have a weaker solvation shell compared to that of Cl - , and consequently were prone to migrate from the aqueous solution to the hydrophobic surface, leading to the anion accumulation responsible for pore wetting. The results are essential for designing nanoporous systems that are selective to ions of the same charge, for realization of ion-induced wetting in hydrophobic pores, as well as for fundamental understanding on the role of ion hydration shell on the properties of solid/liquid interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Material Choice on Biocide Loss in Orion Water Storage Tanks

When preparing for long-duration spaceflight missions, maintaining a safe supply of potable water is of the utmost importance. One major aspect of that is ensuring that microbial growth is minimized. Historically, this challenge has been addressed through the use of biocides. When using biocides, the choice of materials for the storage containers is important, because surface reactions can reduce biocide concentrations below their effective range. In the water storage system baselined for the Orion vehicle, the primary wetted materials are stainless steel (316 L) and a titanium alloy (Ti6Al4V). Previous testing with these materials has shown that the biocide selected for use in the system (ionic silver) will plate out rapidly upon initial wetting of the system. One potential approach for maintaining an adequate biocide concentration is to spike the water supply with high levels of biocide in an attempt to passivate the surface. To evaluate this hypothesis, samples of the wetted materials were tested individually and together to determine the relative loss of biocide under representative surface area-to-volume ratios after 24 hours. Additionally, we have analyzed the efficacy of disinfecting a system containing these materials by measuring reductions in bacterial counts in the same test conditions. Preliminary results indicate that the use of titanium, either individually or in combination with stainless steel, can result in over 95% loss of biocide, while less than 5% is lost when using stainless steel. In bacterial testing, viable organisms were recovered from samples exposed to the titanium coupons after 24 hours. By comparison, no organisms were recovered from the test vessels containing only stainless steel. These results indicate that titanium, while possessing some favorable attributes, may pose additional challenges when used in water storage tanks with ionic silver biocide.

Wallace, W. T.↗

JV Task 126 - Mercury Control Technologies for Electric Utilities Burning Bituminous Coal

The EERC developed an applied research consortium project to test cost-effective mercury (Hg) control technologies for utilities burning bituminous coals. The project goal was to test innovative Hg control technologies that have the potential to reduce Hg emissions from bituminous coal-fired power plants by {ge}90% at costs of one-half to three-quarters of current estimates for activated carbon injection (ACI). Hg control technology evaluations were performed using the EERC's combustion test facility (CTF). The CTF was fired on pulverized bituminous coals at 550,000 Btu/hr (580 MJ/hr). The CTF was configured with the following air pollution control devices (APCDs): selective catalytic reduction (SCR) unit, electrostatic precipitator (ESP), and wet flue gas desulfurization system (WFDS). The Hg control technologies investigated as part of this project included ACI (three Norit Americas, Inc., and eleven Envergex sorbents), elemental mercury (Hg{sup 0}) oxidation catalysts (i.e., the noble metals in Hitachi Zosen, Cormetech, and Hitachi SCR catalysts), sorbent enhancement additives (SEAs) (a proprietary EERC additive, trona, and limestone), and blending with a Powder River Basin (PRB) subbituminous coal. These Hg control technologies were evaluated separately, and many were also tested in combination.

01 COAL, LIGNITE, AND PEAT↗

Hydrothermal catalytic conversion of oleic acid to heptadecane over Ni/ZrO 2

There is growing interest in the substitution of expensive noble metal catalysts with low-cost earth-abundant metals in applications targeting biofuels production from waste organic feedstocks. Here, nickel (Ni) catalysts supported on zirconium dioxide (ZrO 2 ), both with and without copper (Cu) as a co-metal, were tested in hydrothermal reactions of unsaturated and saturated C18 fatty acids as models for waste oil feedstocks. In contrast to recent reports, this study showed no enhancement of nickel's activity for fatty acid conversion to alkane products when Cu was present. Ni/ZrO 2 prepared by metal coprecipitation methods converted 100% of oleic acid with 25% selectivity to heptadecane after 5h of reaction at 350 °C using methanol as a hydrogen donor source, increasing to 41% heptadecane after 20 h. Lower yields were observed with catalysts prepared by wet impregnation and using alternative hydrogen donor sources (glycerol, formic acid). Greater selectivity to heptadecane was also observed at higher temperatures (370 °C) and when the initial fatty acid had greater saturation. Longer term exposure to hydrothermal media led to metal sintering and catalyst deactivation. Findings support a path forward to the development of earth-abundant metal catalysts for the upgrading of waste organic feedstocks.

09 BIOMASS FUELS↗

Enabling High-Energy-Density Cathode for Lithium-Sulfur Batteries

High-loading sulfur electrode is critical for high energy Lithium-sulfur (Li-S) batteries used for practical applications. Unfortunately, dense and high-loading sulfur electrodes usually suffer from low sulfur utilization rate and limited cycle life. In this work, effects of electrode porosity on the electrode energy density, cell cycling stability, Li anode interface, and electrolyte/sulfur ratio were systematically investigated using high loading sulfur electrodes. The reduced electrode porosity increases volumetric energy density but also hinders electrode wetting process. To solve this problem, polysulfide (Li2S6) is selected as an electrolyte additive to enhance electrolyte penetration into dense sulfur cathodes. As a result, a high energy density of 1300 Wh L-1 (at electrode level) has been obtained for a dense sulfur cathode with a sulfur loading of 4 mg cm-2 at a compressed thickness of 60 µm. Li-S batteries with dense electrodes and Li2S6 additive also demonstrate promising cycling stability (~80 % capacity retention for 200 cycles). These significant improvements are contributed by synergistic effects of the dense sulfur cathode, improved electrolyte penetration, and suppressed growth of passivation layer on Li metal anode. This study sheds light on rational sulfur cathode structure design as well as control of electrode porosity for balanced energy density and cycling life.

Lu, Dongping↗

The MELTSPREAD Code for Modeling of Ex-Vessel Core Debris Spreading Behavior, Code Manual – Version3-beta

MELTSPREAD3 is a transient one-dimensional computer code that has been developed to predict the gravity-driven flow and freezing behavior of molten reactor core materials (corium) in containment geometries. Predictions can be made for corium flowing across surfaces under either dry or wet cavity conditions. The spreading surfaces that can be selected are steel, concrete, a user-specified material (e.g., a ceramic), or an arbitrary combination thereof. The corium can have a wide range of compositions of reactor core materials that includes distinct oxide phases (predominantly Zr, and steel oxides) plus metallic phases (predominantly Zr and steel). The code requires input that describes the containment geometry, melt “pour” conditions, and cavity atmospheric conditions (i.e., pressure, temperature, and cavity flooding information). For cases in which the cavity contains a preexisting water layer at the time of RPV failure, melt jet breakup and particle bed formation can be calculated mechanistically given the time-dependent melt pour conditions (input data) as well as the heatup and boiloff of water in the melt impingement zone (calculated). For core debris impacting either the containment floor or previously spread material, the code calculates the transient hydrodynamics and heat transfer which determine the spreading and freezing behavior of the melt. The code predicts conditions at the end of the spreading stage, including melt relocation distance, depth and material composition profiles, substrate ablation profile, and wall heatup. Code output can be used as input to other models such as CORQUENCH that evaluate long term core-concrete interaction behavior following the transient spreading stage. MELTSPREAD3 was originally developed to investigate BWR Mark I liner vulnerability, but has been substantially upgraded and applied to other reactor designs (e.g., the EPR), and more recently to the plant accidents at Fukushima Daiichi. The most recent round of improvements that are documented in this report have been specifically implemented to support industry in developing Severe Accident Water Management (SAWM) strategies for Boiling Water Reactors.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The MELTSPREAD Code for Modeling of Ex-Vessel Core Debris Spreading Behavior

MELTSPREAD3 is a transient 1-D computer code that has been developed to predict the gravity-driven flow and freezing behavior of molten reactor core materials (corium) in containment geometries. Predictions can be made for corium flowing across surfaces under either dry or wet cavity conditions. The spreading surfaces that can be selected are steel, concrete, a user-specified material (e.g., a ceramic), or an arbitrary combination thereof. The corium can have a wide range of compositions of reactor core materials that includes distinct oxide phases (predominantly UO 2 , ZrO 2 and steel oxides) plus metallic phases (predominantly Zr and steel).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Performance of filament-wound vessels from an organic fiber in several epoxy matrices

A study was carried out to select a state-of-the-art epoxy for wet filament winding. Ten epoxy systems were used to filament wind pressure vessels with a high-modulus, high-strength organic fiber. Data are reported on vessel performance, fiber strand strengths, and shear strengths for the different systems. Using our criteria (processibility, neat resin properties, and vessel performance), we find that an epoxy system based on the rubber-modified bis-phenol-F resin, diluted with vinyl cyclohexane dioxide and cured with mixed aromatic amines, can easily replace bis-phenol-A epoxies diluted with bis-(2, 3-epoxycyclopentyl) ether (such as ERL 2256 epoxy of Union Carbide) with comparable overall performance.

Chiao, T. T.↗

NASA Engineering Safety Center NASA Aerospace Flight Battery Systems Working Group 2007 Proactive Task Status

In 2007, the NASA Engineering Safety Center (NESC) chartered the NASA Aerospace Flight Battery Systems Working Group to bring forth and address critical battery-related performance/manufacturing issues for NASA and the aerospace community. A suite of tasks identifying and addressing issues related to Ni-H2 and Li-ion battery chemistries was submitted and selected for implementation. The current NESC funded are: (1) Wet Life of Ni-H2 Batteries (2) Binding Procurement (3) NASA Lithium-Ion Battery Guidelines (3a) Li-Ion Performance Assessment (3b) Li-Ion Guidelines Document (3b-i) Assessment of Applicability of Pouch Cells for Aerospace Missions (3b-ii) High Voltage Risk Assessment (3b-iii) Safe Charge Rates for Li-Ion Cells (4) Availability of Source Material for Li-Ion Cells (5) NASA Aerospace Battery Workshop This presentation provides a brief overview of the tasks in the 2007 plan and serves as an introduction to more detailed discussions on each of the specific tasks.

Manzo, Michelle A.↗

Solid surface wetting and the deployment of drops in microgravity

The complete or partial deployment of liquid samples in low gravity is primarily influenced by the interfacial properties of the specific liquid and solid materials used because the overwhelming bias of the Earth gravitational acceleration is removed. This study addresses the engineering aspects of injecting and deploying drops of prescribed volume into an acoustic positioning chamber in microgravity. The specific problems of interest are the design, testing, and implementation of injector tips to be used in a simultaneously retracting dual-injector system in the Drop Physics Module microgravity experiment facility. Prior to release, the liquid to be deployed must be retained within a restricted area at the very end of the injectors under dynamic stimuli from the continuous injection flow as well as from the stepped motion of the injectors. The final released drop must have a well determined volume and negligible residual linear or angular momentum. The outcome of Earth-based short-duration low gravity experiments had been the selection of two types of injector tips which were flown as back-up parts. They were successfully utilized during the USML-1 Spacelab mission as the primary tips. The combination of a larger contact surface, liquid pinning with a sharp edge, and selective coating of strategic tip surfaces with a non-wetting compound has allowed a significant increase in the success rate of deployment of simple and compound drops of aqueous solutions of glycerol and silicone oil. The diameter of the samples studied in the Drop Physics Module range between 0.3 and 2.7 cm. The tests conducted on-orbit with a manually operated small device have allowed the calibration of the volume deployed for a few drop sizes. The design for improved tips to be used during the next USML flight is based on these results.

Trinh, E. H.↗

Nitrous oxide and methane emissions and nitrous oxide isotopic composition from waste incineration in Switzerland

Highlights: • N{sub 2}O emissions from waste incineration with SNCR NO{sub x} removal are 51.5 ± 10.6 g t{sup −1}. • This is significantly lower than the reported Swiss emission factor of 120 g t{sup −1} (FOEN, 2013). • N{sub 2}O contributes <0.3% and ≈2.5% of GHG emissions from SCR and SNCR plants. • Measured isotopic SP of 17.7‰ is likely characteristic for N{sub 2}O emissions from SNCR. • CH{sub 4} emitted by waste incineration is negligible, contributing <0.01% to total GHGs. - Abstract: Solid waste incineration accounts for a growing proportion of waste disposal in both developed and developing countries, therefore it is important to constrain emissions of greenhouse gases from these facilities. At five Swiss waste incineration facilities with grate firing, emission factors for N{sub 2}O and CH{sub 4} were determined based on measurements of representative flue gas samples, which were collected in Tedlar bags over a one year period (September 2010–August 2011) and analysed with FTIR spectroscopy. All five plants burn a mixture of household and industrial waste, and two of the plants employ NO{sub x} removal through selective non-catalytic reduction (SNCR) while three plants use selective catalytic reduction (SCR) for NO{sub x} removal. N{sub 2}O emissions from incineration plants with NO{sub x} removal through selective catalytic reduction were 4.3 ± 4.0 g N{sub 2}O tonne{sup −1} waste (wet) (hereafter abbreviated as t{sup −1}) (0.4 ± 0.4 g N{sub 2}O GJ{sup −1}), ten times lower than from plants with selective non-catalytic reduction (51.5 ± 10.6 g N{sub 2}O t{sup −1}; 4.5 ± 0.9 g N{sub 2}O GJ{sup −1}). These emission factors, which are much lower than the value of 120 g N{sub 2}O t{sup −1} (10.4 g N{sub 2}O GJ{sup −1}) used in the 2013 Swiss national greenhouse gas emission inventory, have been implemented in the most recent Swiss emission inventory. In addition, the isotopic composition of N{sub 2}O emitted from the two plants with SNCR, which had considerable N{sub 2}O emissions, was measured using quantum cascade laser spectroscopy. The isotopic site preference of N{sub 2}O – the enrichment of {sup 14}N{sup 15}NO relative to {sup 15}N{sup 14}NO – was found to be 17.6 ± 0.8‰, with no significant difference between the two plants. Comparison to previous studies suggests SP of 17–19‰ may be characteristic for N{sub 2}O produced from SNCR. Methane emissions were found to be insignificant, with a maximum emission factor of 2.5 ± 5.6 g CH{sub 4} t{sup −1} (0.2 ± 0.5 g CH{sub 4} GJ{sup −1}), which is expected due to high incinerator temperatures and efficient combustion.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Solid Surface Wetting and the Deployment of Drops in Microgravity

The complete or partial deployment of liquid samples in low gravity is primarily influenced by the interfacial properties of the specific liquid and solid materials used because the overwhelming bias of the Earth gravitational acceleration is removed. This study addresses the engineering aspects of injecting and deploying drops of prescribed volume into an acoustic positioning chamber in microgravity. The specific problems of interest are the design, testing, and implementation of injector tips to be used in a simuttaneously retracting dual-injector system used in the Drop Physics Module microgravity experiment facility. Prior to release, the liquid to be deployed must be retained within a restricted area at the very end of the injectors even under dynamic stimuli due to continuous injection flow as well as to the stepped motion of the injectors, and the final released drop must have a well determined volume as well as negligible residual linear or angular momentum from the deployment process. The outcome of Earthbased short-duration low gravity experiments had been the selection of two types of injector tips which were flown as back-up parts and were successfully utilized during the USML-1 Spacelab mission. The combination of a larger contact surface, liquid pinning with a sharp edge, and selective coating of strategic tip surfaces with a non-wetting compound has allowed a significant increase in the success rate of deployment of simple and compound drops of aqueous solutions of glycerol and silicone oil. The diameter of the samples studied in the Drop Physics Module ranged between 0.3 and 2.7 cm. The tests conducted onsrbit with a manually operated small device have allowed the calibration of the volume deployed for a few drop sizes. The design for improved tips to be used during the next USML flight is based on these results.

Trinh, E. H.↗

Taxon-specific microbial growth and mortality patterns reveal distinct temporal population responses to rewetting in a California grassland soil

Abstract Microbial activity increases after rewetting dry soil, resulting in a pulse of carbon mineralization and nutrient availability. The biogeochemical responses to wet-up are reasonably well understood and known to be microbially mediated. Yet, the population level dynamics, and the resulting changes in microbial community patterns, are not well understood as ecological phenomena. Here, we used sequencing of 16S rRNA genes coupled with heavy water (H218O) DNA quantitative stable isotope probing to estimate population-specific rates of growth and mortality in response to a simulated wet-up event in a California annual grassland soil. Bacterial growth and mortality responded rapidly to wet-up, within 3 h, and continued throughout the 168 h incubation, with patterns of sequential growth observed at the phylum level. Of the 37 phyla detected in the prewet community, growth was found in 18 phyla while mortality was measured in 26 phyla. Rapid growth and mortality rates were measurable within 3 h of wet-up but had contrasting characteristics; growth at 3 h was dominated by select taxa within the Proteobacteria and Firmicutes, whereas mortality was taxonomically widespread. Furthermore, across the community, mortality exhibited density-independence, consistent with the indiscriminate shock resulting from dry-down and wet-up, whereas growth was density-dependent, consistent with control by competition or predation. Total aggregated growth across the community was highly correlated with total soil CO2 production. Together, these results illustrate how previously “invisible” population responses can translate quantitatively to emergent observations of ecosystem-scale biogeochemistry.

58 GEOSCIENCES↗

A Rapid Survey of the Compatibility of Selected Seal Materials with Conventional and Semi-Synthetic JP-8

Since the synthesis of a liquid hydrocarbon fuel from coal by Franz Fischer and Hans Tropsch in 1923, there has been cyclic interest in developing this fuel for military and commercial applications. In recent years the U.S. Department of Defense has taken interest in producing a unified battlespace fuel using the Fischer Tropsch (FT) process for a variety of reasons including cost, quality, and logistics. In the past year there has been a particular emphasis on moving quickly to demonstrate that an FT fuel can be used in the form of a blend with conventional petroleum-derived jet fuel. The initial objective is to employ this semi-synthetic fuel with blend ratios as high as 50 percent FT with longer range goals to use even high blend ratios and ultimately a fully synthetic jet fuel. A significant concern associated with the use of a semi-synthetic jet fuel with high FT blend ratios is the effect these low aromatic fuels will have on fuel-wetted polymeric materials, most notably seals and sealants. These materials typically swell and soften to some degree when exposed to jet fuel and the aromatic content of these fuels contribute to this effect. Semi-synthetic jet fuels with very low aromatic contents may cause seals and sealants to shrink and harden leading to acute or chronic failure. Unfortunately, most of the material qualification tests are more concerned with excessive swelling than shrinkage and there is little guidance offered as to an acceptable level of shrinkage or other changes in physical properties related to low aromatic content. Given the pressing need for guidance data, a program was developed to rapidly survey the volume swell of selected fuel-wetted materials in a range of conventional and semi-synthetic jet fuels and through a statistical analysis to make a determination as to whether there was a basis to be concerned about using fuels with FT blend ratios as high as 50 percent. Concurrent with this analysis data was obtained as to the composition of the fuel absorbed in fuel-wetted materials through the use of GC-MS analysis of swollen samples as well as other supporting data. In this presentation the authors will present a summary of the results of the volume swell and fuel absorbed by selected O-rings and sealants as well as a description of the measurement protocols developed for this program.

Graham, John L.↗

100-NR-2 Apatite Treatability Test: Fall 2010 Tracer Infiltration Test (White Paper)

The primary objectives of the tracer infiltration test were to 1) determine whether field-scale hydraulic properties for the compacted roadbed materials and underlying Hanford fm. sediments comprising the zone of water table fluctuation beneath the site are consistent with estimates based laboratory-scale measurements on core samples and 2) characterize wetting front advancement and distribution of soil moisture achieved for the selected application rate. These primary objectives were met. The test successfully demonstrated that 1) the remaining 2 to 3 ft of compacted roadbed material below the infiltration gallery does not limit infiltration rates to levels that would be expected to eliminate near surface application as a viable amendment delivery approach and 2) the combined aqueous and geophysical monitoring approaches employed at this site, with some operational adjustments based on lessons learned, provides an effective means of assessing wetting front advancement and the distribution of soil moisture achieved for a given solution application. Reasonably good agreement between predicted and observed tracer and moisture front advancement rates was observed. During the first tracer infiltration test, which used a solution application rate of 0.7 cm/hr, tracer arrivals were observed at the water table (10 to 12 ft below the bottom of the infiltration gallery) after approximately 5 days, for an advancement rate of approximately 2 ft/day. This advancement rate is generally consistent with pre-test modeling results that predicted tracer arrival at the water table after approximately 5 days (see Figure 8, bottom left panel). This agreement indicates that hydraulic property values specified in the model for the compacted roadbed materials and underlying Hanford formation sediments, which were based on laboratory-scale measurements, are reasonable estimates of actual field-scale conditions. Additional work is needed to develop a working relationship between resistivity change and the associated change in moisture content so that 4D images of moisture content change can be generated. Results from this field test will be available for any future Ca-citrate-PO4 amendment infiltration tests, which would be designed to evaluate the efficacy of using near surface application of amendments to form apatite mineral phases in the upper portion of the zone of water table fluctuation.

54 ENVIRONMENTAL SCIENCES↗

Scale selection and propagation of wave-CISK with conditional heating

Analytic solutions are derived for simple models of equatorial wave-CISK with conditional (positive-only) heating. Conditional heating favors an unstable mode having a single wet region of infinitesimal width. This result helps explain model simulations of tropical superclusters and intraseasonal oscillations. Mechanisms of scale selection and propagation are discussed, and the model is generalized to include evaporation-wind feedback, multiple vertical-mode CISK, and scale-dependent damping. The first two mechanisms cause zonal propagation, without scale selection. Scale-dependent damping breaks the inviscid continuum (wherein modes exist as a continuous function of wet region width) into discrete modes with unique horizontal structure and phase speed. Results are contrasted with the hierarchy of scales in observed intraseasonal oscillations.

Dunkerton, Timothy J.↗

Selection of representative general circulation models under climatic uncertainty for Western North America

Abstract Climate change research uses an ensemble of general circulation model runs (GCMs-runs) to predict future climate under uncertainties. To reduce computational costs, this study selects representative GCM-runs (RGCM-runs) for Western North America (WNA) based on their performance in replicating historical climate conditions from 1981 to 2005 and projecting future changes from 1981–2010 to 2071–2100. This evaluation is conducted under two representative concentration pathways (RCPs) scenarios, RCP4.5 and RCP8.5, from the Coupled Model Intercomparison Project 5. By using an envelope-based selection technique and a multi-objective distance-based approach, we identify four RGCM-runs per RCP representing diverse climatic conditions, including wet-warm, wet-cold, dry-warm, and dry-cold. Compared to the full-set, these selected runs show a decreased mean absolute error (MAE) between the reference and RGCM-runs concerning the monthly average mean air temperature (T̄) and precipitation (P̄). For RCP4.5, T̄ MAE is 0.45 (vs. 0.58 in the full-set) and P̄ MAE is 0.31 (vs. 0.42). For RCP8.5, T̄ MAE is 0.51 (vs. 0.75) and P̄ MAE is 0.25 (vs. 0.36). The lower MAE values in the RGCM-run set indicate closer alignment between predicted and reference values, making the RGCM-run suitable for climate impact assessments in the region.

Water Resources↗