Search NASA⌕ Search

SEARCH · Search NASA

Results for “sequencing test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Vibration testing of the JE-M-604-4-IUE rocket motor (Thiokol P/N E 28639-03)

The NASA International Ultraviolet Explorer (IUE) rocket motor (TE-M-604-4), a solid fuel, spherical rocket motor, was vibration tested in the Impact, Vibration, and Acceleration (IVA) Test Unit of the von Karman Gas Dynamics Facility (VKF). The objective of the test program was to subject the motor to qualification levels of sinusoidal and random vibration prior to the altitude firing of the motor in the Propulsion Development Test Cell (T-3), Engine Test Facility (ETF), AEDC. The vibration testing consisted of a low level sine survey from 5 to 2,000 Hz, followed by a qualification level sine sweep and qualification level random vibration. A second low level sine survey followed the qualification level testing. This sequence of testing was accomplished in each of three orthogonal axes. No motor problems were observed due to the imposition of these dynamic environments.

Alt, R. E.↗
NASA NTRS1979

Feasibility study of silicon nitride protection of plastic encapsulated semiconductors

The application of low temperature silicon nitride protective layers on wire bonded integrated circuits mounted on lead frame assemblies is reported. An evaluation of the mechanical and electrical compatibility of both plasma nitride and photochemical silicon nitride (photonitride) passivations (parallel evaluations) of integrated circuits which were then encapsulated in plastic is described. Photonitride passivation is compatible with all wire bonded lead frame assemblies, with or without initial chip passivation. Plasma nitride passivation of lead frame assemblies is possible only if the chip is passivated before lead frame assembly. The survival rate after the environmental test sequence of devices with a coating of plasma nitride on the chip and a coating of either plasma nitride or photonitride over the assembled device is significantly greater than that of devices assembled with no nitride protective coating over either chip or lead frame.

Peters, J. W.↗
NASA NTRS1980

Online assessment of a distributed processor

ORT (Operational Readiness Test) software allows one engineer to test readiness of 64 minicomputers and their peripherals from single console. Software makes roll call of computers and peripherals via common data buffer to check readiness of system in morning "wake up" or at other important times. Subsystems are tested in parallel to save time. "Watchdog" terminates test of any system that does not respond in time, so one failed system does not halt test sequence. Entire rollcall is complete in about 15 minutes. Software is designed for Space Shuttle prelaunch checkout, but approach should interest users of similar equipment.

Ehrlich, L. F.↗
NASA NTRS1980

Fatigue strength testing employed for evaluation and acceptance of jet-engine instrumentation probes

This report outlines the fatigue type testing performed on instrumentation rakes and probes intended for use in the air flow passages of jet-engines during full-scale engine tests at Lewis Research Center. Included is a discussion of each type of test performed, the results that may be derived and means of inspection. A design and testing sequence outlines the procedures and considerations involved in the generation of suitable instrument probes.

Armentrout, E. C.↗
NASA NTRS1980

Friction and wear results from sputter-deposited chrome oxide with and without nichrome metallic binders and interlayers

Friction and wear tests were conducted on optimized sputtered Cr2O3 and Cr2O3 with metallic binder coatings. The coatings were applied on the bearing surface of journal foil air bearings and were tested against chrome-carbide-coated journal surfaces. The objective of the study was to develop a coating system which would withstand 9000 start-stops and high-speed rubs (maximum acceleration, 100 gs) in temperatures ranging from room temperature to 650 C. The Cr2O3 coating completed the test sequence and the coating consisting of Cr2O3 with metallic binders completed 3000 start-stops. The coefficient of friction of the coatings at 650 C was found to be about half that at room temperature. It was concluded, therefore, that the coatings should perform much better in a high temperature environment alone. The decrease in friction at high temperature is attributed to oxidation and interactions of the coatings and substrates at the interface temperature.

Bhushan, B.↗
NASA NTRS1981

Applications of digital image acquisition in anthropometry

A description is given of a video kinesimeter, a device for the automatic real-time collection of kinematic and dynamic data. Based on the detection of a single bright spot by three TV cameras, the system provides automatic real-time recording of three-dimensional position and force data. It comprises three cameras, two incandescent lights, a voltage comparator circuit, a central control unit, and a mass storage device. The control unit determines the signal threshold for each camera before testing, sequences the lights, synchronizes and analyzes the scan voltages from the three cameras, digitizes force from a dynamometer, and codes the data for transmission to a floppy disk for recording. Two of the three cameras face each other along the 'X' axis; the third camera, which faces the center of the line between the first two, defines the 'Y' axis. An image from the 'Y' camera and either 'X' camera is necessary for determining the three-dimensional coordinates of the point.

Woolford, B.↗
NASA NTRS1986

A system for the functional testing and simulation of custom and semicustom VLSI chips

A system for the functional testing and simulation of custom and semicustom very large scale integrated (VLSI) chips that are designed using the integrated UNIX-based computer-aided design (CAD) system is described. The testing and simulation system consists of two parts. One of these is a special purpose hardware device that is capable of controlling the digital imputs and outputs on a custom chip. This device, the Digital Microcircuit Functionality Tester (DMFT) system, can be operated by itself or in conjunction with the VAX host computer on the CAD system. The DMFT is integrated into a microprobe station so that these signals can be injected or read from nodes inside the chip, as well as at the pins. The second part of the system is a software package that is installed on the VAX. This software package, logic, includes a full-screen editor for developing chip test sequences and drivers for both the DMFT and the esim logic simulator.

Olson, E. M.↗
NASA NTRS1986

Analysis and simulation of the MAST (COFS-1 flight hardware)

In-house analysis work in support of the Control of Flexible Structures (COFS) program is being performed at the NASA Langley Research Center. The work involves evaluation of the proposed design configuration, controller design as well as actuator dynamic modeling, and MAST/actuator dynamic simulation of excitation and damping. A complete finite element model of the MAST has been developed. This finite element model has been incorporated into an optimization procedure which minimizes total mass while maintaining modal coupling. Results show an increase in the total mass due to additional constraints (namely, the diagonal frequency constraint) imposed on the baseline design. A valid actuator dynamic model is presented and a complete test sequence of the proposed flight experiment is demonstrated. The actuator dynamic model is successfully used for damping and the stroke limitations for first mode excitation are demonstrated. Plans are to incorporate additional design variables and constraints into the optimization procedure (such as actuator location) and explore alternative formulations of the objective function. A different actuator dynamic model to include hardware limitations will be investigated.

Horta, Lucas G.↗
NASA NTRS1988

Concept of a programmable maintenance processor applicable to multiprocessing systems

A programmable maintenance processor concept applicable to multiprocessing systems has been developed at the NASA Ames Research Center's Dryden Flight Research Facility. This stand-alone-processor is intended to provide support for system and application software testing as well as hardware diagnostics. An initial machanization has been incorporated into the extended aircraft interrogation and display system (XAIDS) which is multiprocessing general-purpose ground support equipment. The XAIDS maintenance processor has independent terminal and printer interfaces and a dedicated magnetic bubble memory that stores system test sequences entered from the terminal. This report describes the hardware and software embodied in this processor and shows a typical application in the check-out of a new XAIDS.

Glover, Richard D.↗
NASA NTRS1989

Conceptual design of a moving belt radiator shuttle-attached experiments: Technical requirement Document

The technical requirements for a shuttle-attached Moving Belt Radiator (MBR) experiment are defined. The MBR is an advanced radiator concept in which a rotating belt radiates thermal energy to space. The requirements for integrating the MBR experiment in the shuttle bay are discussed. Requirements for the belt material and working fluid are outlined along with some possible options. The proposed size and relationship to a full scale Moving Belt Radiator are defined. The experiment is defined with the primary goal of dynamic testing and a secondary goal of demonstrating the sealing and heat transfer characteristics. A perturbation system which will simulate a docking maneuver or other type of short term acceleration is proposed for inclusion in the experimental apparatus. A deployment and retraction capability which will aid in evaluating the dynamics of a belt during such a maneuver is also described. The proposed test sequence for the experiment is presented. Details of the conceptual design are not presented herein, but rather in a separate Final Report.

Aguilar, Jerry L.↗
NASA NTRS1990

NASA Langley Research Center National Aero-Space Plane Mission simulation profile sets

To provide information on the potential for long life service of oxidation resistant carbon-carbon (ORCC) materials in the National Aero-Space Plane (NASP) airframe environment, NASP ascent, entry, and cruise trajectories were analytically flown. Temperature and pressure profiles were generated for 20 vehicle locations. Orbital (ascent and entry) and cruise profile sets from four locations are presented along with the humidity exposure and testing sequences that are being used to evaluate ORCC materials. The four profiles show peak temperatures during the ascent leg of an orbital mission of 2800, 2500, 2000, and 1700 F. These profiles bracket conditions where carbon-carbon might be used on the NASP vehicle.

Ohlhorst, Craig W.↗
NASA NTRS1991

Programmable Maintenance Processor For XAIDS

Programmable maintenance processor (MAINT) made of commercially available integrated circuits. Autonomous one of four digital electronic processors in extended aircraft interrogation and display system (XAIDS). Developed for testing of system and application computer programs as well as for testing equipment. MAINT has independent terminal and printer interfaces and dedicated magnetic bubble memory storing system-testing sequences entered from terminal. Software for MAINT written in PLM86 programming language and broken into four separate modules.

Glover, Richard↗
NASA NTRS1990

Vacuum ultraviolet radiation and thermal cycling effects on atomic oxygen protective photovoltaic array blanket materials

The importance of synergistic environmental exposure is demonstrated through the evaluation of DuPont 93-1 in simulated LEO environment. Changes in optical properties, surface condition, and mass loss data are described. The qualitative results indicate the necessity for exposure of materials to a series of simulated LEO environments in order to properly determine synergistic effects and demonstrate the overall LEO durability of candidate materials. It is shown that synergistic effects may occur with vacuum thermal cycling combined with VUV radiation followed by atomic oxygen exposure. Testing the durability of candidate solar array blanket materials in a test sequence with necessary synergistic effects makes it possible to determine the appropriate material for providing structural support and maintaining the proper operating temperature for solar cells in the SSF Photovaltaic Power System.

Brady, J.↗
NASA NTRS1991

Upgraded NERVA systems: Enabler nuclear system

The NERVA/Rover Enabler technology enables to go on a low risk, short-term program to meet the requirements of the Mars mission and maybe some lunar missions. The following subject areas are covered: NERVA technology - the foundation for tomorrow's space missions; NERVA/Rover reactor system test sequence; NERVA engine development program; nuclear thermal reactor capability based on many related Westinghouse technology programs; investment in Rover/Nerva technology; synergistic applications of NERVA technology; flow schematic of the NDR engine; the NERVA nuclear subsystem; and technology evolution.

Farbman, Gerry↗
NASA NTRS1991

Information Flow Analysis of Level 4 Payload Processing Operations

The Level 4 Mission Sequence Test (MST) was studied to develop strategies and recommendations to facilitate information flow. Recommendations developed as a result of this study include revised format of the Test and Assembly Procedure (TAP) document and a conceptualized software based system to assist in the management of information flow during the MST.

Danz, Mary E.↗
NASA NTRS1992

Introduction to study and simulation of low rate video coding schemes

During this period, the development of simulators for the various HDTV systems proposed to the FCC were developed. These simulators will be tested using test sequences from the MPEG committee. The results will be extrapolated to HDTV video sequences. Currently, the simulator for the compression aspects of the Advanced Digital Television (ADTV) was completed. Other HDTV proposals are at various stages of development. A brief overview of the ADTV system is given. Some coding results obtained using the simulator are discussed. These results are compared to those obtained using the CCITT H.261 standard. These results in the context of the CCSDS specifications are evaluated and some suggestions as to how the ADTV system could be implemented in the NASA network are made.

Source record↗
NASA NTRS1992

Electrolysis Performance Improvement and Validation Experiment

Viewgraphs on electrolysis performance improvement and validation experiment are presented. Topics covered include: water electrolysis: an ever increasing need/role for space missions; static feed electrolysis (SFE) technology: a concept developed for space applications; experiment objectives: why test in microgravity environment; and experiment description: approach, hardware description, test sequence and schedule.

Schubert, Franz H.↗