Results for “solubility” — Page 7

DOE OSTI2026

Testing of High S Matrix Glasses to Expand DFHLW Glass Compositional Ranges (Rev.1)

Gaps in glass composition-property data for direct-feed high-level waste (DFHLW) have recently been identified. One such gap is the region of high sulfur solubility since previous, pretreated, high-level wastes contained very little sulfur. Filling this data gap will significantly broaden the range of process flowsheet options including minimal washing and will allow for optimized waste loading in DFHLW glasses. This report summarizes the data collected during the characterization of the DFHLW High S Glass Matrix (HS24). A glass matrix of 50 glass compositions was developed to evenly cover the DFHLW composition region for high sulfur glass. Matrix glasses were designed to expand the composition region outside the current component concentration and property limits so as to reduce uncertainties at the limits. The 50 matrix glasses were fabricated and tested for properties important to the success of DFHLW vitrification including: compositions, canister centerline cooling (CCC) crystallinity and isothermal crystallinity, density, viscosity, electrical conductivity (EC), product consistency test (PCT) response, toxicity, and sulfate solubility. Melter materials corrosion testing is reported elsewhere. These glasses were intentionally designed to have high SO 3 solubilities (0.7 to 2.2 SO 3 wt%) in compositional regions that had not been previously explored. Forty-eight glasses showed the measured SO 3 content retained >80% of the target SO 3 and the densities of all the glasses ranged from 2.49 g·cm -3 to 2.74 g·cm -3 . While the model predicted nepheline formation in 5 glasses, one of the tested 50 CCC glasses formed nepheline, and 35 glasses formed Cr-containing phases such as spinels and eskolaite. Only five glasses were amorphous after CCC treatment where 44 glasses with detectable crystals contained =10 wt% crystals and only one glass had > 10 wt% crystals. None of the glasses exceeded the allowable T 2% for spinel crystal formation at 950 ºC (i.e., no glasses had >2 wt% spinel at 950 ºC) during isothermal crystal fraction tests where 10 glasses showed no crystalline phases at or below 950 ºC. All the glasses (except one which failed being slightly lower than the target) satisfied the SO 3 constraint while 98 glasses did not meet the viscosity constraints and 4 failed the EC constraints. Six quenched (Q) and six CCC glasses failed the Defense Waste Processing Facility (DWPF) Environmental Assessment (EA) glass PCT threshold and 3 Q and 4 CCC failed the PCT design constraint. One glass exceeded the WTP delisting limits for Cr via EPA Method 1311 (i.e., Toxicity Characteristic Leaching Procedure, TCLP). It should be emphasized that some of these glasses were specifically designed to approach or even exceed certain property constraints, as filling data gaps in these regions will provide the greatest benefit for future model development by improving accuracy and reducing uncertainties. These insights will ultimately support the development of more robust glass formulation strategies, enabling higher waste loading, reducing operational risks, and expanding the processing envelope.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2026

Fluorinated Glyme Solvents to Extend Lithium-Sulfur Battery Life (Final Technical Report, Unlimited)

This project investigated a number of partially fluorinated glymes (PFGs) as electrolyte cosolvents to improve the performance of lithium-sulfur (Li-S) batteries. A major issue in Li-S cells is the electrochemical reaction of sulfur in the cathode to form lithium polysulfides (LPS) that dissolve in the electrolyte. Those LPS are electrochemically and chemically reactive at the lithium anode, resulting in lithium sulfide deposition on the anode and also electrochemical reaction at both the anode and cathode, leading to a “polysulfide shuttle” and reduced coulombic efficiency (CE) and self-discharge of the cell. PFGs reduce the solubility of LPS while maintaining good solubility of lithium salts such as LiTFSI. By adjusting the amount of PFG as cosolvent in the electrolyte, we showed that the solubility of LPS in the electrolyte can be tuned. (It is not desirable to completely eliminate LPS in the electrolyte, as they facilitate electrochemical reaction of the electrically insulating S 8 and Li 2 S within the cathode by shuttling charge between them and the conductive carbon.) Another issue in Li-S cells is degradation of the Li anode over many cycles of stripping (discharge) and plating (charge). We showed that PFGs have a beneficial effect on the physical morphology of the Li anode, SEI formation, and the CE of a Li-Li cell. Among the many PFGs tested, we found the best performance from PFGs designated PFG2 and PFG5, and these two PFGs were thoroughly studied. A systematic coin-cell study of electrolyte solvents of 90:10, 80:20, or 70:30 DME:PFG (DME = 1,2-dimethoxyethane) revealed some systematic trends: a higher percentage of PFG solvent led to substantially longer cycle life, but at the same time reduced specific capacity (mAh/g(S)) and cell capacity at higher rates. These studies used LiFSI as the electrolyte salt, as it was found to extend cycle life compared to LiTFSI. Finally, the addition of a small amount of 1,3-dioxolane (DOL) to the electrolyte was found to be beneficial. The overall optimal electrolyte solution was found to be 0.6 M LiFSI + 0.5 M LiNO 3 in 75:5:20 DME/DOL/PFG (either PFG2 or PFG5).

25 ENERGY STORAGE↗

DOE OSTI2025

Guiding Principles for Geochemical/Thermodynamic Model Development and Validation in Nuclear Waste Disposal: A Close Examination of Recent Thermodynamic Models for H + —Nd 3+ —NO 3 - (—Oxalate) Systems

Development of a defensible source-term model (STM), usually a thermodynamical model for radionuclide solubility calculations, is critical to a performance assessment (PA) of a geologic repository for nuclear waste disposal. Such a model is generally subjected to rigorous regulatory scrutiny. In this article, we highlight key guiding principles for STM model development and validation in nuclear waste management. We illustrate these principles by closely examining three recently developed thermodynamic models with the Pitzer formulism for aqueous H + —Nd 3+ —NO 3 - (—oxalate) systems in a reverse alphabetical order of the authors: the XW model developed by Xiong and Wang, the OWC model developed by Oakes et al., and the GLC model developed by Guignot et al., among which the XW model deals with trace activity coefficients for Nd(III), while the OWC and GLC models are for concentrated Nd(NO 3 ) 3 electrolyte solutions. The principles highlighted include the following: (1) Principle 1. Validation against independent experimental data: A model should be validated against experimental data or field observations that have not been used in the original model parameterization. We tested the XW model against multiple independent experimental data sets including electromotive force (EMF), solubility, water vapor, and water activity measurements. The results show that the XW model is accurate and valid for its intended use for predicting trace activity coefficients and therefore Nd solubility in repository environments. (2) Principle 2. Testing for relevant and sensitive variables: Solution pH is such a variable for an STM and easily acquirable. All three models are checked for their ability to predict pH conditions in Nd(NO 3 ) 3 electrolyte solutions. The OWC model fails to provide a reasonable estimate for solution pH conditions, thus casting serious doubt on its validity for a source-term calculation. In contrast, both the XW and GLC models predict close-to-neutral pH values, in agreement with experimental measurements. (3) Principle 3. Honoring physical constraints: Upon close examination, it is found that the Nd(III)-NO 3 association schema in the OWC model suffers from two shortcomings. Firstly, its second stepwise stability constant for Nd(NO 3 ) 2+ (log K 2 ) is much higher than the first stepwise stability constant for NdNO 3 2+ (log K 1 ), thus violating the general rule of (log K 2 –log K 1 ) < 0, or $\frac{K1}{K2}$>1. Secondly, the OWC model predicts abnormally high activity coefficients for Nd(NO 3 ) 2 + (up to ~900) as the concentration increases. (4) Principle 4. Minimizing degrees of freedom for model fitting: The OWC model with nine fitted parameters is compared with the GLC model with five fitted parameters, as both models apply to the concentrated region for Nd(NO 3 ) 3 electrolyte solutions. The latter appears superior to the former because the latter can fit osmotic coefficient data equally well with fewer model parameters. The work presented here thus illustrates the salient points of geochemical model development, selection, and validation in nuclear waste management.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

CMI Winter Meeting 2025 Presentation

Lanthanides are important to many technologies including magnets used in high efficiency traction motors. While common in the environment and industrial waste streams, lanthanides are often present at very low concentrations. This work demonstrates synergistic lanthanide recovery from an aqueous magnet leachate to single ppm concentrations using Na2SO4 addition and subsequent DME-FC treatment. It was found that combining DME-FC with low concentrations of Na2SO4 (~0.1 M) results in synergistic isolation of lanthanides while making use of Na2SO4, an excessive byproduct of hydrometallurgical metal production. Combined Na2SO4 + DME reduced lanthanide metal ion's (Pr, Nd, Sm, Gd, Dy, and Ho) solubilities by 1,000 - 25,000x with final concentrations ranging from 2 ppm to 200 ppm. This can be compared to 0.1 M Na2SO4 alone providing a 10 - 200x reduction and DME providing a 100 - 1,500x reduction in lanthanide solubilities. Final solution concentrations of lanthanides were 99.8% lower than what could not be achieved with either individual process. The results also reveal different periodic trends in the solubility reduction for DME and Na2SO4.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗

DOE OSTI2026

Hydrogeological assessment of CO2 containment assurance and wellbore integrity at a Gulf Coast storage site

Abstract A large-scale carbon capture and storage (CCS) initiative on the Texas Gulf Coast serves as a premier demonstration of the U.S. Department of Energy’s CarbonSAFE program. Targeting deep saline formations, specifically Oligo-Miocene deltaic sequences, the project aims to establish technical and commercial viability for geologic CO2 storage within a major industrial corridor. This study provides a rigorous hydrogeological assessment to support Class VI permitting by quantifying the high degree of containment security. Utilizing a compositional reservoir simulator, we developed a suite of 27 distinct simulation cases to evaluate vertical plume dynamics near both planned injection wells and proximal legacy infrastructure. To ensure numerical accuracy near wellbores, we implemented a refined mesh strategy, determining that a 5.6 ft × 5.6 ft grid refinement offered the optimal balance between computational efficiency and descriptive precision. The modeling framework utilized a systematic sensitivity-based approach to evaluate the mechanical redundancy of the subsurface system by performing a bounding analysis of wellbore interfaces against hypothetical high-permeability microannuli. By systematically isolating competing physical drivers, including permeability, porosity, gas hysteresis, thermal gradients, salinity, and solubility trapping (quantified via Henry’s law with dynamically adjusted coefficients), this work moves beyond binary assessments to establish a nuanced hierarchy of containment factors. The results confirm that primary trapping mechanisms (e.g., gas hysteresis and solubility), combined with the site's unique geomechanical stratigraphy, significantly restrict vertical mobility and reinforce the robust containment security of the reservoir. Baseline results demonstrate substantial vertical separation between the CO2 plume and the upper confining system, ensuring robust containment. Sensitivity analysis reveals that even under highly conservative bounding scenarios—assuming theoretical 10-Darcy pathways at specific wellbore locations—the 2,900-ft thick multi-layered confining zone remains a reliable barrier. In these hypothetical upper-bound cases, peak upward fluxes of CO2 and saltwater after 15 years of injection remain localized and dissipate rapidly within the lower sections of the confining interval, leaving the integrity of the seal uncompromised. Furthermore, the study identifies that while localized wellbore pathways define theoretical upper bounds of vertical migration, the Area of Review (AoR) is primarily sensitive to regional thermal gradients and hysteresis, which can influence the AoR by over 3,000 acres in pessimistic configurations. Also, primary trapping mechanisms, specifically gas hysteresis and solubility, work in tandem with the Gulf Coast’s unique geomechanical stratigraphy to significantly restrict vertical mobility. Ductile, smectite-rich mudstones facilitate natural borehole convergence and the self-healing of potential conduits, creating a natural geomechanical bridge that effectively mitigates migration potential at both current injection points and legacy-well locations. This comprehensive modeling effort demonstrates that the integration of high-resolution wellbore simulations and regional geomechanical observations confirms the long-term storage security of the studied site, providing a physics-based foundation for industrial-scale CCS deployments. This modeling framework establishes a baseline for future research into coupled geomechanical effects, such as time-dependent borehole convergence, to further refine long-term containment projections. Acknowledgements We thank the Gulf Coast Carbon Center (GCCC) at the Bureau of Economic Geology for foundational research support. We appreciate Alex Bump for technical guidance and David Hoffman for model mesh generation. This work used TACC’s Frontera cluster for simulations and CMG Ltd. software licenses provided to UT-Austin. This material is based upon work supported by the Department of Energy under Award Number DE-FE0032338. Disclaimer This material is based upon work supported by the U.S. Department of Energy’s Fossil Energy and Carbon Management Office under the CarbonSAFE program, award Number DE-FE0032338. The views expressed herein do not necessarily represent the views of the U.S. Department of Energy or the United States Government.

58 GEOSCIENCES↗

DOE OSTI2026

Hydrogeological assessment of CO2 containment assurance and wellbore integrity at a Gulf Coast storage site

Abstract A large-scale carbon capture and storage (CCS) initiative on the Texas Gulf Coast serves as a premier demonstration of the U.S. Department of Energy’s CarbonSAFE program. Targeting deep saline formations, specifically Oligo-Miocene deltaic sequences, the project aims to establish technical and commercial viability for geologic CO2 storage within a major industrial corridor. This study provides a rigorous hydrogeological assessment to support Class VI permitting by quantifying the high degree of containment security. Utilizing a compositional reservoir simulator, we developed a suite of 27 distinct simulation cases to evaluate vertical plume dynamics near both planned injection wells and proximal legacy infrastructure. To ensure numerical accuracy near wellbores, we implemented a refined mesh strategy, determining that a 5.6 ft × 5.6 ft grid refinement offered the optimal balance between computational efficiency and descriptive precision. The modeling framework utilized a systematic sensitivity-based approach to evaluate the mechanical redundancy of the subsurface system by performing a bounding analysis of wellbore interfaces against hypothetical high-permeability microannuli. By systematically isolating competing physical drivers, including permeability, porosity, gas hysteresis, thermal gradients, salinity, and solubility trapping (quantified via Henry’s law with dynamically adjusted coefficients), this work moves beyond binary assessments to establish a nuanced hierarchy of containment factors. The results confirm that primary trapping mechanisms (e.g., gas hysteresis and solubility), combined with the site's unique geomechanical stratigraphy, significantly restrict vertical mobility and reinforce the robust containment security of the reservoir. Baseline results demonstrate substantial vertical separation between the CO2 plume and the upper confining system, ensuring robust containment. Sensitivity analysis reveals that even under highly conservative bounding scenarios—assuming theoretical 10-Darcy pathways at specific wellbore locations—the 2,900-ft thick multi-layered confining zone remains a reliable barrier. In these hypothetical upper-bound cases, peak upward fluxes of CO2 and saltwater after 15 years of injection remain localized and dissipate rapidly within the lower sections of the confining interval, leaving the integrity of the seal uncompromised. Furthermore, the study identifies that while localized wellbore pathways define theoretical upper bounds of vertical migration, the Area of Review (AoR) is primarily sensitive to regional thermal gradients and hysteresis, which can influence the AoR by over 3,000 acres in pessimistic configurations. Also, primary trapping mechanisms, specifically gas hysteresis and solubility, work in tandem with the Gulf Coast’s unique geomechanical stratigraphy to significantly restrict vertical mobility. Ductile, smectite-rich mudstones facilitate natural borehole convergence and the self-healing of potential conduits, creating a natural geomechanical bridge that effectively mitigates migration potential at both current injection points and legacy-well locations. This comprehensive modeling effort demonstrates that the integration of high-resolution wellbore simulations and regional geomechanical observations confirms the long-term storage security of the studied site, providing a physics-based foundation for industrial-scale CCS deployments. This modeling framework establishes a baseline for future research into coupled geomechanical effects, such as time-dependent borehole convergence, to further refine long-term containment projections. Acknowledgements We thank the Gulf Coast Carbon Center (GCCC) at the Bureau of Economic Geology for foundational research support. We appreciate Alex Bump for technical guidance and David Hoffman for model mesh generation. This work used TACC’s Frontera cluster for simulations and CMG Ltd. software licenses provided to UT-Austin. This material is based upon work supported by the Department of Energy under Award Number DE-FE0032338. Disclaimer This material is based upon work supported by the U.S. Department of Energy’s Fossil Energy and Carbon Management Office under the CarbonSAFE program, award Number DE-FE0032338. The views expressed herein do not necessarily represent the views of the U.S. Department of Energy or the United States Government.

58 GEOSCIENCES↗

DOE OSTI2024

Thermodynamic and Kinetic Modulation of Methylammonium Lead Bromide Crystallization Revealed by In Situ Monitoring

Hybrid organic–inorganic perovskite (HOIP) crystals are promising optoelectronic materials, but little is known about either the thermodynamic and kinetic controls on crystal growth or the underlying growth mechanism(s). Herein, we use fluid cell atomic force microscopy (AFM) and solution nuclear magnetic resonance (NMR) spectroscopy to investigate growth of the model HOIP crystal CH 3 NH 3 PbBr 3 (MAPbBr 3 ) and to determine how formic acid (HCOOH) modulates the thermodynamics and kinetics of growth. The results show that growth of MAPbBr 3 in dimethylformamide (DMF) proceeds through the classical pathway by the spreading of atomic crystal steps generated at screw dislocations on the {100} surface. Temperature dependent step velocity measurements demonstrate that with increasing concentration, HCOOH decreases both the solubility of MAPbBr 3 and the kinetic coefficient (b) of step movement. 1 H-NMR measurements indicate that HCOOH increases the lifetime of the methylammonium (MA + ) ions and promotes the association of MAPbBr 3 , thus tuning the solubility of the perovskite. HCOOH also alters the molecular tumbling motion and bulk diffusion of the MA + ions, possibly via H-bonding. Further, our findings establish a direct correlation between the mesoscale crystal growth kinetics and the molecular-scale interactions between organic additives and constituent ions, providing unprecedented insights for developing predictive syntheses of HOIP crystals with defined size, crystal habit and shape, and defect distribution.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Molecular Design Considerations for Azobenzene Anolytes

Realization of high-density batteries requires the development of anolytes that display highly negative reduction potentials, solubility, and persistence in the charged state. Azobenzenes have garnered interest as potential anolytes for redox flow batteries. Here, we report the synthesis of a family of substituted azobenzene derivatives and evaluation of their solution-phase electrochemical properties. Systematic synthetic derivatization of this scaffold allows (1) access to anolytes of varying solubility, including intrinsically liquid derivatives that represent potential high-density charge carriers; (2) systematic variation of the reduction potential, and in some cases redox inventory, that provides azobenzenes with highly negative reduction potentials; and (3) control of the lifetime of the azobenzene radical anions that result from one-electron reduction. Electrokinetic experiments demonstrated that fast electron transfer occurs for all derivatives examined. Spectroscopic characterization of monoreduced azobenzene derivatives establishes that decomposition of the azobenzene radical anion proceeds via bimolecular disproportionation. Together, these results provide an experimental basis for the optimization of azobenzene anolytes for electrochemical storage applications, including redox flow batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Sustainable Triacetic Acid Lactone Production from Sugarcane by Fermentation and Crystallization

Triacetic acid lactone (TAL) has the potential to serve as a bioderived platform chemical for commercial products including sorbic acid and recyclable polydiketoenamine plastics. In this study, we leveraged BioSTEAM to design, simulate, and evaluate (via techno-economic analysis, TEA, and life cycle assessment, LCA) TAL production from sugarcane. We experimentally characterized TAL solubility, calibrated solubility models, and designed a process to separate TAL from fermentation broths by crystallization. The biorefinery could produce TAL at a minimum product selling price (MPSP) of $\$3.73$–5.86·kg –1 (5th–95th percentiles; baseline at $\$4.60$·kg –1 ) and a carbon intensity (CI) of 5.31 [2.60–8.71] kg CO 2 -eq·kg –1 , which could enable financially viable, low-CI production of sorbic acid and polydiketoenamines. To drive down costs and CI, we explored the theoretical fermentation space (titer, yield, productivity combinations), operation scheduling and capacity expansion strategies (e.g., integrated sorghum processing), and potential separation improvements (mitigating TAL loss through pH control). Advancements in key design and technological parameters could further reduce MPSP by 51% to $\$2.26$·kg –1 [$\$1.97$–2.80·kg –1 ] and CI by 43% to 3.05 [1.91–4.15] kg CO 2 -eq·kg –1 . This research highlights the ability of agile TEA-LCA to screen promising designs, navigate sustainability trade-offs, prioritize research needs, and chart quantitative roadmaps to advance bioproducts and biofuels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Ionic Liquids for Direct Air Capture of CO 2 using Electric‐Field‐Mediated Moisture Gradient Process (Final Technical Report)

The final report provides executive summary, a list of publications, and information on training graduate students and postdoctoral researchers. We carried out computational and experimental research on understanding molecular-level mechanism of how CO 2 is absorbed in a solution containing ethylene glycol as the solvent and KOH as the salt in the presence of ionic liquids and under the influence of electric field. In doing so, we developed an automated high-throughput method which allowed us to measure the solubility of CO 2 in a large number of ionic liquids, considerably speeding up the CO 2 solubility measurement. We also demonstrated how varying the concentration of ionic liquids in ethylene glycol can result in a maximum in ionic conductivity. Reaction of CO 2 and subsequent release results in a 50% reduction when the process is operated at an ionic liquid-ethylene glycol concentration yielding maximum ionic conductivity amongst all the ionic liquid-ethylene glycol combinations studied as a part of this research. We utilized machine learning models to identify unique ionic liquid-solvent combinations with ionic conductivity much higher than that measured for ionic liquid-ethylene glycol combinations. We demonstrated that the rate of CO 2 reaction with KOH in ethylene glycol can be optimized with the type of ionic liquid and its concentration. Overall, the research led to publication of 10 peer-reviewed research articles and several presentations at national conferences. We are also in the process of developing additional manuscripts based on the research carried out as a part of this project. Two graduate students and two postdoctoral researchers were supported on the funding.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Breaking Barriers in Chalcogenide Perovskite Synthesis: A Generalized Framework for Fabrication of BaMS 3 (M═Ti, Zr, Hf) Materials

Abstract Chalcogenide perovskites have garnered increasing attention as stable, non‐toxic alternatives to lead halide perovskites. However, their conventional synthesis at high temperatures (>1000 °C) has hindered widespread adoption. Recent studies have developed low‐to‐moderate temperature synthesis methods (<600 °C) using reactive precursors, yet a comprehensive understanding of the pivotal factors affecting reproducibility and repeatability remains elusive. This study delineates the critical factors in the low‐temperature synthesis of BaMS 3 (M═Zr, Hf, Ti) compounds and presents a generalized framework. Innovative approaches are developed for synthesizing BaMS 3 compounds using this framework involving organometallics for solution deposition. The molecular precursor routes, employing metal acetylacetonates to generate soluble metal–sulfur bonded complexes and metal–organic compounds to produce soluble metal‐thiolate, metal‐isothiocyanate, and metal‐trithiocarbonate species, are demonstrated to yield carbon‐free BaMS 3 . These methods have achieved the most contiguous films of BaZrS 3 and BaHfS 3 using solution deposition to date. Furthermore, a hybrid solution processing method involving stacking sputter‐deposited Zr and solution‐deposited BaS layers is employed to synthesize a contiguous, oxygen‐free BaZrS 3 film. The diffuse reflectance measurements indicate a direct bandgap of ≈ 1.85 eV for the BaZrS 3 films and ≈ 2.1 eV for the BaHfS 3 film under investigation.

25 ENERGY STORAGE↗

DOE OSTI2024

Tetrahydrofuran Processable Organic Solar Cells with 19.45% Efficiency Realized by Introducing High Molecular Dipole Unit Into the Terpolymer

Developing organic solar cells (OSCs) processable with halogen‐free, non‐aromatic solvents is crucial for practical applications, yet challenging due to the limited solubility of most photoactive materials. Here, this study introduces high‐performance terpolymers processable in tetrahydrofuran (THF) by incorporating dithienophthalimide (DPI) into the PM6 backbone. DPI extends the absorption band, lowers HOMO levels, and improves THF solubility and film crystallinity through its large dipole moment effect. Optimal PBD‐10:L8‐BO devices processed with THF achieved a competitive power conversion efficiency (PCE) of 18.79%, approaching chloroform‐processed devices (19.04%). By introducing PBTz‐F as a second donor, ternary OSCs reached an impressive 19.45% PCE when processed with THF. This improvement stems from enhanced photon generation, improved morphology, better charge transport, longer exciton lifetimes, efficient charge dissociation and collection, and suppressed recombination. These PCEs of 18.79% and 19.45% for binary and ternary blend OSCs, respectively, represent the highest reported efficiencies for OSCs processed with halogen‐free, non‐aromatic solvents. This work demonstrates significant progress in eco‐friendly OSC fabrication, paving the way for more sustainable and commercially viable organic photovoltaic technologies.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Green Electrode Processing Enabled by Fluoro-Free Multifunctional Binders for Lithium-Ion Batteries

The eco-friendly processing of conjugated polymer binder for lithium-ion batteries demands improved polymer solubility by introducing functional moieties, while this strategy will concurrently sacrifice polymer conductivity. Employing the polyfluorene-based binder poly(2,7-9,9 (di(oxy-2,5,8-trioxadecane))fluorene) (PFO), soluble in water-ethanol mixtures, a novel approach is presented to solve this trade-off, which features integration of aqueous solution processing with subsequent controlled thermal-induced cleavage of solubilizing side chains, to produce hierarchically ordered structures (HOS). The thermal processing can enhance the intermolecular π–π stacking of polyfluorene backbone for better electrochemical performance. Notably, HOS-PFO demonstrated a substantial 6–7 orders of magnitude enhancement in electronic conductivity, showcasing its potential as a functional binder for lithium-ion batteries. As an illustration, HOS-PFO protected SiOx anodes, utilizing in situ side chain decomposition of PFO surrounding SiOx particles after aqueous processing are fabricated. HOS-PFO contributed to the stable cycling and high-capacity retention of practical SiOx anodes (3.0 mAh cm -2 ), without the use of any conducting carbon additives or fluorinated electrolyte additives. It is proposed that this technique represents a universal approach for fabricating electrodes with conjugated polymer binders from aqueous solutions without compromising conductivity.

25 ENERGY STORAGE↗

DOE OSTI2024

A Fluorinated Lewis Acidic Organoboron Tunes Polysulfide Complex Structure for High–Performance Lithium–Sulfur Batteries

Many challenges in lithium-sulfur (Li–S) batteries are associated with the radical change in lithium polysulfide (LPS) solubility during cycling, but chemical approaches to address such inconsistency are still lacking. Here, the use of a strong Lewis acidic fluorinated organoboron, tri(2,2,2-trifluoroethyl) borate (TFEB), is reported as a multi-functional mediator to simultaneously overcome multiple technical barriers in practical Li–S batteries. TFEB acts as an anion acceptor and forms strong molecular complexes with Lewis basic LPS. The TFEB-LPS complexes have consistent solubility across the full polysulfide spectrum and deliver several times improved better redox kinetics, unlocking a true redox catalytic mechanism that covers the majority of redox events in thick sulfur cathodes. As a result, Li–S batteries evaluated under practical conditions exhibit significantly improved discharge capacity, rate capability, and cycling stability with the addition of the TFEB additive. More importantly, TFEB also contributes to the stabilization of lithium anode in the presence of polysulfides by generating strong interfacial film. These attributes significantly improve the cycling stability of practical Li–S pouch cells, which are assembled with a unit energy density of 219 Wh kg –1 . Finally, the results provide new molecular insights on the design of unlocking solvation networks of practical Li–S systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2025

Aqueous Zr/Hf IV ‐Oxo Cluster Speciation and Separation

Abstract Many industrial separations of chemically‐similar elements are achieved by solvent extraction, exploiting differences in speciation and solubility across aqueous‐organic interfaces. We recently identified [OM 4 (OH) 6 (SCN) 12 ] 4− (OM 4 , M=Zr/Hf IV ) tetrahedral oxoclusters as the main species in industrial processes that produce nuclear‐grade Zr and Hf from crude ore. However, isostructural/isoelectronic OM 4 ‐oxoclusters do not explain selective extraction of Hf into the organic phase. Here we have characterized heterometal Hf−Zr clusters in solution and the solid‐state yielding key information about their fundamentally different chemistry that engenders separation. Clusters prepared with both ammonium (industrial process) and tetramethylammonium counter cations revealed that 1) heterometal clusters (instead of a mixture of homometal clusters) assemble, and 2) Hf‐rich OM 4 selectively precipitates over Zr‐rich OM 4 , providing a separation process that does not require an organic extractant. Mass spectrometry, small‐angle X‐ray scattering, solution‐state 1 H nuclear magnetic resonance (NMR) spectroscopy, and solid‐state 17 O NMR evidence both mixed‐metal speciation and selective Hf‐precipitation. Raman spectroscopy suggests greater Zr‐ligand lability than Hf‐ligand lability, consistent with higher aqueous solubility of Zr‐rich clusters, enabling both extraction and precipitation‐based separation. Fundamentally, we also identify a key difference between these chemically similar elements that has enabled diversification of Zr‐polyoxocation chemistry over the last decade, while Hf‐polyoxocation chemistry lags.

Roseborough, Alexander [Department of Chemistry Or↗

DOE OSTI2026

Harnessing plant‐based platform for low‐cost cellulosic sugar recovery from bioenergy crops

The price of pure cellulase enzyme for the recovery of fermentable cellulosic sugars is one of the major challenges that limit the commercialization of second-generation biofuels and bio-based products. This work shows a means to greatly reduce the cost of cellulases. The abundant capacity of plants to synthesize and hyperaccumulate transgenic proteins in their plastids has been demonstrated for two gene constructs using either NPT II or Tet C to regulate the expression of bacterial cellulase Cel6A. Previously, the expression of Cel6A to 20–35% of total soluble leaf protein in tobacco was shown in two consecutive field trials. Moving forward, the key challenge was the extraction of active enzymes from the transgenic tobacco leaves hyperaccumulating bacterial cellulases in a cost-effective manner. The study showed that unpurified crude extracts of NPT II and Tet C transgenic tobacco leaves recovered ~23% and ~29% w/w cellulosic sugars from energycane bagasse, respectively. A supplementation of as low as 25% of purified commercial cellulase improved the glucose recovery by 2.9 times (~85% w/w) compared to 100% crude extract, which is comparable to the glucose recovery obtained by commercial cellulases, thereby suggesting a reduced requirement of commercial cellulases leading to a cost reduction of 75% for biorefineries. Assuming a stable 40% cellulase yield in total soluble protein under field conditions and multiple harvests (one to three) a year, the study estimates that the potential cost for saccharification of 1 t of lignocellulosic biomass can be reduced to 67–200 USD by using crude leaf extracts of transgenic tobacco.

biofuel↗

DOE OSTI2025

Lanthanide Sulfate Recovery by Synergistic Dimethyl Ether and Na 2 SO 4 Fractional Crystallization

Lanthanides (Lns) are important to many technologies including magnets used in high-efficiency traction motors and generators. While commonly occurring in the environment and industrial waste streams, Ln are generally present at low concentrations. This work demonstrates synergistic Ln recovery from an aqueous magnet leachate to single ppm concentrations using Na 2 SO 4 addition and subsequent dimethyl ether-driven fractional crystallization (DME-FC) treatment. It is found that combining DME-FC with low concentrations of Na 2 SO 4 (≈0.1 M) results in synergistic isolation of Lns while making use of Na 2 SO 4 , an excessive byproduct of hydrometallurgical metal production. Combined Na 2 SO 4 + DME reduces Ln metal ion (Pr, Nd, Sm, Gd, Dy, and Ho) solubilities by 700–27,000x with final concentrations ranging from 2 ppm to 200 ppm. Separately, Na 2 SO 4 0.1 M provides a 10–200x reduction and DME provides a 90–1,400x reduction in Ln solubilities. Final Ln concentrations of the combined process are 99.8% lower than what is achieved with each individual process.

dimethyl ether↗

DOE OSTI2025

Detection of non‐native species formed during fibrillization of the myocilin olfactomedin domain

Abstract Glaucoma is a group of neurodegenerative diseases that together are the leading cause of irreversible blindness worldwide. Myocilin‐associated glaucoma is an inherited form of this disease, caused by intracellular aggregation of misfolded mutant myocilin. In vitro, the myocilin C‐terminal olfactomedin domain (OLF), the relevant domain for glaucoma pathogenesis, can be driven to form amyloid‐like fibrils under mild conditions. Here we characterize a species present during in vitro fibrillization. Purified OLF was subjected to fibrillization at concentrations required for downstream electron microscopy imaging and NMR spectroscopy. Additional biophysical techniques, including analytical ultracentrifugation and X‐ray crystallography, were employed to further characterize the multicomponent mixture. Negative stain transmission electron microscopy (TEM) shows a non‐native species reminiscent of known prefibrillar oligomers from other amyloid systems, NMR indicates a minor population of partially misfolded species is present in solution, and cryo‐EM imaging shows two‐dimensional protein arrays. The predominant soluble species remaining in solution after the fibril reaction is natively folded, as evidenced by X‐ray crystallography. In summary, after incubating OLF under fibrillization‐promoting conditions, there is a heterogeneous mixture consisting of soluble folded protein, mature amyloid‐like fibrils, and partially misfolded intermediate species that at present belie additional molecular detail. The characterization of OLF fibrillar species illustrates the challenges associated with developing a comprehensive understanding of the fibrillization process for large, non‐model amyloidogenic proteins.

Scelsi, Hailee F. [School of Chemistry and Biochem↗