Search NASA⌕ Search

SEARCH · Search NASA

Results for “spall”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

RDS-21 Face-Gear Surface Durability Tests

Experimental fatigue tests were performed to determine the surface durability life of a face gear in mesh with a tapered spur involute pinion. Twenty-four sets of gears were tested at three load levels: 7200, 8185, and 9075 lb-in face gear torque, and 2190 to 3280 rpm face gear speed. The gears were carburized and ground, shot-peened and vibro-honed, and made from VIM-VAR Pyrowear 53 steel per AMS 6308. The tests produced 17 gear tooth spalling failures and 7 suspensions. For all the failed sets, spalling occurred on at least one tooth of all the pinions. In some cases, the spalling initiated a crack in the pinion teeth which progressed to tooth fracture. Also, spalling occurred on some face gear teeth. The AGMA endurance allowable stress for a tapered spur involute pinion in mesh with a face gear was determined to be 275 ksi for the material tested. For the application of a tapered spur involute pinion in mesh with a face gear, proper face gear shim controlled the desired gear tooth contact pattern while proper pinion shim was an effective way of adjusting backlash without severely affecting the contact pattern.

Lewicki, David G.↗
NASA NTRS2010

Discontinuous Inter-Granular Separations (DIGS) in the Gas Nitride Layer of ISS Race Rings

The starboard solar alpha rotary joint (SARJ) race ring on the International space station (ISS) failed due to severe spalling of the outer diameter, 45 degree (outer canted) nitrided surface. Subsequent analysis at NASA-KSC revealed that almost all of the debris generated due to the failure was nitrided 15-5 stainless steel. Subsequent analysis of the nitride control coupons (NCC) at NASA-JSC revealed the presence of discontinuous inter-granular separations (DIGS) in the gas nitride layer. These DIGS were present in the inter-granular networking located in the top 2 mils of the nitride layer. The manufacturer's specification requires the maximum white structure to be 0.0003 inches and intergranular networking below the allowable white structure depth to be cause for rejection; a requirement that the NCCs did not meet. Subsequent testing and analysis revealed that lower DIGS content significantly lowered the probability of nitride spalling in simulated, dry condition runs. One batch of nitride samples with DIGS content similar to the port SARJ (did not fail on orbit) which exhibited almost no nitride spalling after being run on one test rig. Another batch of nitride samples with DIGS content levels similar to the starboard SARJ exhibited significant nitride spalling on the same test rig with the same load under dry conditions. Although DIGS were not the root cause of starboard race ring failure, testing indicates that increased DIGS reduced the robustness of the gas nitride layer under dry operating conditions.

Figert, John↗
NASA NTRS2004

Windows(Registered Trademark)-Based Software Models Cyclic Oxidation Behavior

Oxidation of high-temperature aerospace materials is a universal issue for combustion-path components in turbine or rocket engines. In addition to the question of the consumption of material due to growth of protective scale at use temperatures, there is also the question of cyclic effects and spallation of scale on cooldown. The spallation results in the removal of part of the protective oxide in a discontinuous step and thereby opens the way for more rapid oxidation upon reheating. In experiments, cyclic oxidation behavior is most commonly characterized by measuring changes in weight during extended time intervals that include hundreds or thousands of heating and cooling cycles. Weight gains occurring during isothermal scale-growth processes have been well characterized as being parabolic or nearly parabolic functions of time because diffusion controls reaction rates. In contrast, the net weight change in cyclic oxidation is the sum of the effects of the growth and spallation of scale. Typically, the net weight gain in cyclic oxidation is determined only empirically (that is, by measurement), with no unique or straightforward mathematical connection to either the rate of growth or the amount of metal consumed. Thus, there is a need for mathematical modeling to infer spallation mechanisms. COSP is a computer program that models the growth and spallation processes of cyclic oxidation on the basis of a few elementary assumptions that were discussed in COSP: A Computer Model of Cyclic Oxidation, Oxidation of Metals, vol. 36, numbers 1 and 2, 1991, pages 81-112. Inputs to the model include the selection of an oxidation-growth law and a spalling geometry, plus oxide-phase, growth-rate, cycle-duration, and spall-constant parameters. (The spalling fraction is often shown to be a constant factor times the existing amount of scale.) The output of COSP includes the net change in weight, the amounts of retained and spalled oxide, the total amounts of oxygen and metal consumed, and the terminal rates of weight loss and metal consumption.

Smialek, J. L.↗
DOE OSTI2023

Design of Planarizing Growth Conditions on Unpolished and Faceted (100)-Oriented GaAs Substrates Using Hydride Vapor Phase Epitaxy

Here we performed a design of experiments (DoE) analysis to determine the effect of various growth parameters on in situ planarizing overgrowth of rough substrates using hydride vapor phase epitaxy (HVPE). We used two types of rough (100)-oriented GaAs substrates to compare the effect of the initial morphology on the epitaxial growth behavior: an irregular, as-cut surface resultant from cutting the wafer from a GaAs boule and a regularly faceted surface produced by controlled spalling. The DoE analysis identified trends in the overgrowth behavior with changing growth conditions, and we used these trends to design favorable planarization growth conditions for each surface type. These favorable conditions enabled full planarization of a spalled surface with >2.5 um facet height within 10.8 min of growth. The root mean squared (RMS) surface roughness of the resulting (100) surface was 24.5 nm over a 286 um x 215 um area. Our results show that planarization growth by HVPE is a promising technique to enable device growth directly on rough substrates, and the trends revealed through DoE analysis indicate a path toward further optimization of planarization growth conditions for as-cut and spalled surfaces.

14 SOLAR ENERGY↗
DOE OSTI2022

Dynamic properties of 316l stainless steel repaired using electron beam additive manufacturing

Additive manufacturing has the potential to be used for repair of high-value parts, but the strength and integrity of such repaired parts, especially under dynamic loading, in still unknown. This work presents the results of high strain-rate dynamic testing of additively repaired stainless steel samples. The 316L samples were intentionally damaged and subsequently repaired with 308L stainless steel wire using electron beam additive manufacturing. The repaired samples were subjected to gas-gun impact testing to induce incipient damage and determine the role played by the repaired region in dictating damage and failure. The results show the following: 1) the equation of state of the repaired region is comparable to the original material as shown by the unchanged spall plane location, 2) the deformation behavior is similar to the original material as shown by the similar Hugoniot Elastic limit, 3) the spall strength of the repaired region is slightly higher than the original material due to varying grain size, and 4) the damage morphology in the repaired region is different and involves a high rate of void coalescence. In conclusion, despite these minor differences in the spall strength and the damage morphology, the overall dynamic response of the original material and repaired samples is similar suggesting that AM is a promising approach for repairing high-value components.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of moderate temperatures on compressive strength of ultra-high-performance concrete: A microstructural analysis

Highlights: • All coarse aggregates and steel fibres were surrounded by the binder. • X-ray diffraction is useful for explaining the increase in compressive strength with increasing temperature. • Rosenhahnite and/or quartz Dauphiné-twinned phases improved the compressive strength. • Polypropylene fibres prevented spalling and preserved the compressive strength. • Concrete with steel and polypropylene fibres did not exhibit spalling at 300 °C. Concrete with two types of steel fibres and a polypropylene fibre prevented spalling and preserved the compressive strength at 300 °C, which makes these concretes suitable for long-term applications up to 300 °C, such as for steam collectors or thermal energy storage systems. The compressive strength behaviour of three types of ultra-high-performance fibre-reinforced concrete manufactured with the same matrix was investigated. For this purpose, a complete characterisation of all the raw materials and the three types of fibres used was performed. The morphology of all concrete mixtures at room temperature was analysed using scanning electron microscopy–energy-dispersive X-ray spectroscopy. From the results, it was ascertained that the steel fibres and coarse siliceous aggregates were not in contact (being separated by ≥3.41 μm) and were surrounded by the binder (of ≥1 μm in thickness) for all the mixtures studied. Rosenhahnite and/or quartz Dauphiné-twinned phases improved the compressive strength (as determined by X-ray diffraction).

36 MATERIALS SCIENCE↗
DOE OSTI2021

The simulation of 3D hypervelocity spallation using a hydrocode PAGOSA with FLIP+MPM

n this work, a hydrocode PAGOSA with FLIP+MPM is presented and exercised to investigate the fracture in ductile material. The merit of PAGOSA with FLIP+MPM to solve the advection problem is first illustrated by a solid piston periodically moving in a sealed tube with air. Furthermore, the ability of PAGOSA with FLIP+MPM to capture the fracture in material is shown by a simple stretching fracture in ductile material. In both of two benchmark problems, the PAGOSA results and analytical solutions are also presented for comparison. Then PAGOSA with FLIP+MPM is used to model complex spall in ductile material, which is a challenging problem in engineering applications. The convergences of PAGOSA with FLIP+MPM—based on both the mesh size and the marker density—are investigated by monitoring free surface velocity. To further show the ability of PAGOSA with FLIP+MPM to predict fracture in ductile material, the numerical results are compared with the experimental results and other published numerical results. Moreover, the effect of the spall parameter in PAGOSA with FLIP+MPM on the numerical simulation is also analyzed by investigating the free surface velocity. Finally, the effects of the peak compressive stress, the tensile strain rate, and the loading rate on the spallation are further investigated. The numerical results show that PAGOSA with FLIP+MPM can improve PAGOSA's performance when applied to predicting fracture in ductile materials, and is robust enough to accurately predict spall fracture in ductile materials.

42 ENGINEERING↗
DOE OSTI2020

Hydrothermal Corrosion of First-Generation Dual-Purpose Coatings on Silicon Carbide for Accident-Tolerant Fuel Cladding

In this study, four different commercial coatings, TiN, Cr, CrN, and Cr/CrN (multilayer) were deposited by physical vapor deposition (PVD) on high resistivity chemical vapor deposited (CVD) SiC for the dual purpose of corrosion mitigation and fission gas hermeticity. The coatings were exposed for up to 2600 hours in flowing high temperature (288-350°C), high purity, liquid water with dissolved hydrogen (0.15-3ppm) or dissolved oxygen (1-2ppm). The Cr/CrN coatings did not adhere well and spalled quickly during exposure. In oxygenated conditions, none of the coatings were protective . CrN coatings spalled preferentially at defect sites, but reacted slowly enough in the absence of defects to potentially be chemically protective. TiN coatings fully oxidized within a few hundred hours and spalled. In hydrogen, all the coatings were chemically stable. Coating failures were identified and attributed to localized spallation, potentially related to coating defects. Coating improvements are recommended to reduce spallation and improve coating protection for future generations of dual-purpose coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Atomistic study of silicon alloying in the spallation behavior of nanocrystalline aluminum systems

Here, the effect of concentration of the alloying element silicon (Si) on the shock and spall response of aluminum (Al) is studied using classical molecular dynamics (MD) simulations. Silicon is distributed as individual grains and as grain boundaries and the dynamic response under shock is studied for an impact velocity of 1000 m/s. A general trend observed here is that the spallation is almost exclusively intergranular and limited to Al-Si interfaces. The spall strengths are observed to a) decrease with an increase in alloying of Si as grains and b) show little increase for up to 50% grain boundary segregation. An increase in grain size of the whole system showed negligible differences in spall strength, highlighting the significance of concentration of the alloying species rather than its grain size. These results provide an atomistic understanding of light-weight metallic systems under shock compression and pave the way for designing multiphase metal matrix alloys and composites for defense/armor applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Damage initiation and evolution in Al-Si layered microstructures under shock loading conditions at atomic scales

Designing materials with microstructural features like multiphase interfaces have shown significant promise for usage in the next generation defense and nuclear applications. The dynamic response of these interfaces in extreme environments is observed to vary with the deformability of individual phases, which could subsequently alter the favored damage nucleation sites related to spall failure. Here, we investigate the role of spacing of interfaces in a nanocrystalline layered Aluminum-Silicon system on the shock wave propagation behavior, and microstructural and defect evolution using classical molecular dynamics simulations. The simulations are carried out with different hypothetical Al/Si microstructures including variations in the distribution of Si grains as layers in a nanocrystalline Al matrix. The molecular dynamics simulations suggest that spall failure is preferentially initiated at Al/Si interfaces. In addition, for the same system volume and same concentration of Si, a higher number of layers is marked by an increase in shock wave velocity and reduced resistance to spall failure.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of macroscopic surface defects on dynamic damage: An experimental and numerical study

This study examines the impact of macroscopic surface defects on the dynamic ductile damage behavior of polycrystalline metals using plate-impact experiments. Defects of various shapes (flat, round, and point) were manufactured on the free or impact surfaces of annealed copper specimens. The experiments were diagnosed with photon Doppler velocimetry measurements and soft recovery techniques. The experimental results revealed that defect shape and location significantly affect velocity–time profiles and void distribution. In order to understand the dynamics of shock propagation and corresponding ductile damage evolution within the target specimens, the impact experiments were modeled with a calibrated Tepla model, a dynamic ductile damage model for polycrystalline metals [Nguyen et al., Int. J. Solids Struct. 329, 113833 (2026)]. Overall, our resulting simulated velocity showed good agreement with measured velocity, and our simulated porosity distributions qualitatively matched experimental data. Based on our simulation results, defects on the free surface were found to distort rarefaction waves and therefore the corresponding spall planes. On the other hand, defects on the impact surface generated a delayed shock when the flyer plate and the defected target area were in contact, leading to distortion of the spall plane. The distortion of the spall plane resulted in a non-uniform distribution of voids within the defected specimens. Lastly, we examined the role of local work hardening due to the defect manufacturing process on the velocity and porosity distribution, using Tepla simulations with a simplified representation of local hardening. This investigation highlights the importance of defect geometry, location, and local hardening associated with defect generation in dynamic ductile damage processes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Main Bearing Replacement and Damage - A Field Data Study on 15 Gigawatts of Wind Energy Capacity

This study seeks to establish a comprehensive baseline of knowledge for the replacement and damage of main bearings in wind turbines. The purpose of this report is to provide a high-level summary of the data set, methodology, and results of this work. Full technical details and an extended analysis will be made available in a future publication. We collected data on main bearing replacements and reported damage from industrial partners based in Europe and the United States. In total, we obtained data for 167 wind power plants, with a combined capacity of 15.3 gigawatts (GW). Most of the data set was comprised of land-based, three-point mount, spherical roller bearings. Within this data set were 689 instances of main bearing replacement. Analysis was undertaken in two parts: first, a statistical analysis of the main bearing time-to-replacement data using survival analysis techniques; second, quantitative and qualitative analyses of the obtained damage information. Our results showed that 10% of a fixed main bearing population would be expected to have been replaced by 10.5 years. This is close to half of the 20-year design value. Fitted parametric distributions then indicated that by year 20, between 22% and 25% of main bearings are expected to have been replaced. Analysis of the damage reports revealed spalling to be the main type of damage listed. The additional presence of surface damage in the collected data indicates that at least part of the spalling cases are likely due to surface-initiated rolling contact fatigue. At this stage is not clear what proportion of spalling cases result from "wear induced", surface-initiated and subsurface-initiated rolling contact fatigue. While this work provides important insights into the current state of main bearing replacements and damage, many questions remain. An ongoing and expanding data collection and analysis effort focused on wind turbine main bearings is therefore recommended.

17 WIND ENERGY↗
NASA NTRS1973

Cyclic oxidation evaluation: Approaching application conditions

A survey is presented of the cyclic furnace and burner rig oxidation facilities at NASA-Lewis Research Center together with a review of selected test results and an initial interpretation of the data obtained. Cyclic furnace tests are used to conveniently screen alloy oxidation resistance and spall tendency; high velocity tests further indicate dynamic environmental resistance. Alloys which form scales predominantly of Cr2O3/chromite spinel spall much more than those forming alpha Al2O3/aluminate spinel scales. Weight changes due to scale spalling were used to estimate alloy depletion/thickness losses.

Barrett, C. A.↗
NASA NTRS1972

Lunar microcraters and interplanetary dust.

The ratio of spall to pit diameter of lunar microcraters decreases with decreasing crater size. The trend from micron-sized to cm-sized craters involves a transition of crater types from pit-only to pit-plus-spall craters. Some spall-only craters may have possessed a pit originally. Most microcraters are formed by the impact of primary interplanetary dust particles because melting occurred during their formation. According to experimental and theoretical data such melting phenomena require impact velocities which are consistent only with the velocity distribution of extralunar particles.

Hartung, J. B.↗
NASA NTRS1978

The role of thermal shock in cyclic oxidation

The effect of thermal shock on the spalling of oxides from the surfaces of several commercial alloys was determined. The average cooling rate was varied from approximately 240 C per second to less than 1.0 C per second during cyclic oxidation tests in air. The tests consisted of one hundred cycles of one hour at the maximum temperature (1100 or 1200 C). The alloys were HOS-875, TD-Ni, TD-NiCrAl, IN-601, IN-702, and B-1900 plus Hf. All of these alloys exhibited partial spalling within the oxide rather than total oxide loss down to bare metal. Thermal shock resulted in deformation of the metal which in turn resulted, in most cases, in changing the oxide failure mode from compressive to tensile. Tensile failures were characterized by cracking of the oxide and little loss, while compressive failures were characterized by explosive loss of platelets of oxide. This behavior was confirmed by examination of mechanically stressed oxide scales. The thermally shocked oxides spalled less than the slow cooled samples with the exception of TD-NiCrAl. This material failed in a brittle manner rather than by plastic deformation.

Lowell, C. E.↗
NASA NTRS1981

High temperature cyclic oxidation furnace testing at NASA Lewis Research Center

A standardized method of testing the cyclic oxidation resistance of various alloys in static air to 1200 C was developed and is routinely used at NASA Lewis Research Center. Test samples are automatically raised and lowered into a resistance wound furnace for a series of fixed interval heating and cooling cycles. Spall catchers collect the accumulated spall from each sample. The samples are weighed intermittently to generate specific weight change/time data. At various test times the samples and the accumulated spall are analyzed by X-ray diffraction. A computer program uses this gravimetric and X-ray data as input to print out the oxidation curves and specific weight change/time and X-ray results in a published format, organizes, and indexes the data. So far, several hundred Fe, Ni, and Co base alloys were tested using this same basic procedure and results form the basis of a series of cyclic oxidation handbooks to be published by NASA. Such specific weight change/time data were used to estimate the oxidative metal consumption by several computer modeling techniques to rank alloys and for use in life testing estimates.

Barrett, C. A.↗
NASA NTRS1981

High temperature cyclic oxidation furnace testing at NASA Lewis Research Center

A standardized method of testing the cyclic oxidation resistance of various alloys in static air up to 1200 C has been developed and routinely used at the NASA Lewis Research Center. Test samples are automatically raised and lowered into a resistance wound furnace for a series of fixed-interval heating and cooling cycles. Spall catchers collect the accumulated spall from each sample. The samples are weighed intermittently to generate specific weight change with time data. At various test times the samples and the accumulated spall are analyzed by X-ray diffraction. A computer program is used to print out the specific weight change versus time data and the X-ray data in tabular form and to plot the specific weight change versus time data in a publishable format. The data are also organized and indexed. So far several hundred Fe-, Ni-, and Co-base alloys have been tested using this basic procedure and will form the basis of a series of cyclic oxidation handbooks to be published by NASA. Such specific weight change/time data have been used to estimate the oxidative metal consumption by several computer modeling techniques both to rank alloys and to estimate life.

Barrett, C. A.↗
NASA NTRS1983

Cyclic oxidation of superalloys

The development of mathematical/computer models of cyclic oxidation in high-temperature alloys is described. The acceleration of oxidation attack caused by the spalling of protective oxide scales is discussed. The COREST paralinear model based on empirical data, designed by Barrett and Pressler, is found to be of limited value. Basic research on the spalling process in different alloy systems is reviewed, and the phenomenon is characterized: occurring mainly within the oxide, it is caused by the different thermal expansion coefficients of oxide and metal and is a linear function of the total retained oxide. This information has been used in the development of the discrete oxide-spall model COSP and in its modification by addition of a diffusion-zone-profile model to predict the failure of components (Heckel and Nesbitt, unpublished). The COSP model is shown to produce good predictions of cyclic oxidation under a variety of conditions, using data from simple isothermic tests.

Lowell, C. E.↗