SEARCH · Search NASA

Results for “spark ignition engines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Total Cost of Ownership Reduction Using Passive Pre-Chamber Ignition in Natural Gas Engines

Spark plug durability is a factor affecting the total cost of ownership (TCO) of spark-ignited natural gas engines, with some heavy-duty platforms requiring plug replacement after only 750 hours of operation. The high ignition energy demand under lean or diluted conditions accelerates electrode wear, shortening plug life and increasing maintenance frequency. This work evaluates passive pre-chamber (PC) ignition operating at lowered spark energies as a strategy to reduce spark energy requirements and extend plug durability, thereby lowering TCO. Experiments were conducted on a medium-duty Cummins 6.7L ISB engine at 1600 RPM and 50% load under varying exhaust gas recirculation (EGR) dilution levels (0–40%). Two passive pre-chambers with 1.1 mm and 1.6 mm nozzle diameters were compared with conventional spark ignition (SI). SI was operated with a fixed coil dwell of 4 ms (~90 mJ), while the PC configuration was tested across 2–4 ms dwell times (~30–90 mJ). Cylinder pressure analysis revealed that PC ignition sustained stable combustion at significantly lower spark energies than SI, with improved combustion stability at ~30 mJ compared with SI at ~90 mJ. The PC system also extended the dilution tolerance beyond that achievable with SI, while delivering up to ~2% higher indicated thermal efficiency and reducing the COV by nearly 90% at 30% EGR. A TCO analysis was conducted to assess the economic benefit of adopting a passive PC system operating at reduced spark energies compared to SI. It was found that adopting a passive PC system could reduce TCO by approximately $11,000 per engine over a five-year operational period, primarily due to fuel savings, extended spark plug life, and reduced maintenance frequency. These projections were weighed against the additional hardware cost of the pre-chamber, yielding a rapid estimated return on investment of ~300 operating hours. Therefore, this work motivates continued research and development of passive PC technology and its commercial adoption in natural gas engines used in transportation applications.

Dhotre, Akash [University of Minnesota]↗

DOE OSTI2023

Commercialization of a Comprehensive Spark-Ignition Model for Automotive Engine Applications in CONVERGE CFD

The work completed under this CRADA commercializes an advanced hybrid Lagrangian-Eulerian spark-ignition (LESI) model for multi-dimensional engine simulations. In this report, LESI is coupled with combustion models (WSR, TFM, G-equation) to model spark channel elongation and kernel and flame development in a constant volume combustion vessel, and a four-valve direct-injection spark-ignition (4VDISI) engine in two operating conditions: stoichiometric E30 with no dilution, and stoichiometric PACE-20 with dilution using CONVERGE CFD solver.

42 ENGINEERING↗

DOE OSTI2023

The effect of chemical functional groups on the octane sensitivity of fuel blends for spark-ignited and multimode engines

We report the octane sensitivity of fuel blends containing blendstocks of diverse chemical functionalities blended in concentrations up to 20% by volume into BOBs (Blendstocks for Oxygenate Blending). This study focuses on the blendstocks containing functional groups which lack reliable octane number data. The effects on octane sensitivity of blends of cyclopropanes, alkyl carbonates, oxiranes, alcohols, ketones, esters, nitrogen-containing compounds, cyclic and olefinic hydrocarbons, multifunctional materials containing combinations of these functionalities, and the co-blends of the blendstocks with ethanol in a BOB have been evaluated. Octane sensitivity of the blends containing functional groups that haven’t been evaluated before are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Coupling a Lagrangian–Eulerian Spark-Ignition (LESI) model with LES combustion models for engine simulations

In the United States transportation sector, Light-Duty Vehicles (LDVs) are the largest energy consumers and CO 2 emitters. Electrification of LDVs is posed as a potential solution, but SI engines can still contribute to decarbonization. Car manufacturers have turned to unconventional engine operation to increase the efficiency of Spark-Ignition (SI) engines and reduce the carbon emissions of their fleets. Dilute, lean, and stratified-charge engine operation has the potential for engine efficiency improvements at the expense of increased cyclic variability and combustion instability. At such demanding engine conditions, the spark ignition event is key for flame initiation and propagation and for enhanced combustion stability. Reliable and accurate spark ignition models can help design ignition systems that reduce cyclic variability. Multiple computational spark-ignition models exist that perform well under conventional conditions, but the underlying physics needs to be expanded, for unconventional engine operation. In this paper, a hybrid Lagrangian–Eulerian Spark-Ignition (LESI) model is coupled with different turbulent flame propagation models for engine simulations. LESI relies on Lagrangian arc tracking and Eulerian energy deposition. The LESI model is coupled with the Well-Stirred Reactor (WSR), Thickened Flame Model (TFM), and g-equation model and used to simulate several cycles of a Direct-Injection Spark-Ignition (DISI) engine using a commercial Computational Fluid Dynamics (CFD) engine solver. The results showcase the successful coupling of LESI with the combustion models. Global engine metrics, such as pressure and Apparent Heat Release Rate (AHRR), for each simulation setup are compared to experimental engine results, for validation. In addition, results highlight the successful prediction of spark channel movement by comparing simulation images to experimental optical engine images. Finally, the successful coupling of LESI to combustion models, making it a usable model in the engine modeling community, is emphasized and future development details are discussed.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

Performance of direct injected propane and gasoline in a high stroke-to-bore ratio SI engine: Pathways to diesel efficiency parity with ultra low soot

This work explores pathways to achieve diesel-like, high-efficiency combustion with stoichiometric 3-way catalyst compatible combustion in a single-cylinder spark ignition (SI) research engine. A unique high stroke-to-bore engine design (1.5:1) with cooled exhaust gas recirculation (EGR) and high compression ratio ( r c ) was used to improve engine efficiency by up to 30% compared with a production turbocharged gasoline direct injection spark ignition engine. Engine experiments were conducted with both 91 RON E10 gasoline and liquified petroleum gas (LPG) (i.e. autogas) and were compared to legacy gasoline data on the production engine. Geometric compression ratio ( r c ) of 13.3:1 was used for both fuels with additional experiments at 16.8:1 for LPG only. Measurements of exhaust soot particle size and number concentrations were made with both fuels. Significant reduction in soot particles across the whole particle size range were achieved with LPG due to the elimination of in-cylinder liquid films. The effects of EGR, late intake valve closing (IVC) and fuel characteristics were investigated through their effects on efficiency, combustion stability and soot production. Results of 47% gross thermal efficiency, and 45% net thermal efficiency at stoichiometric engine operation, at up to 17 bar IMEP and 2000 r/min with 16.8:1 r c were achieved with LPG. Estimated brake efficiency values were compared to a contemporary medium duty diesel engine illustrating the benefits of the chosen path for achieving diesel efficiency parity.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

Mapping the combustion modes of a dual-fuel compression ignition engine

Compression-ignition (CI) engines can produce higher thermal efficiency (TE) and thus lower carbon dioxide (CO 2 ) emissions than spark-ignition (SI) engines. Unfortunately, the overall fuel economy of CI engine vehicles is limited by their emissions of nitrogen oxides (NO x ) and soot, which must be mitigated with costly, resource- and energy-intensive aftertreatment. NO x and soot could also be mitigated by adding premixed gasoline to complement the conventional, non-premixed direct injection (DI) of diesel fuel in CI engines. Several such “dual-fuel” combustion modes have been introduced in recent years, but these modes are usually studied individually at discrete conditions. This paper introduces a mapping system for dual-fuel CI modes that links together several previously studied modes across a continuous two-dimensional diagram. This system includes the conventional diesel combustion (CDC) and conventional dual-fuel (CDF) modes; the well-explored advanced combustion modes of HCCI, RCCI, PCCI, and PPCI; and a previously discovered but relatively unexplored combustion mode that is herein titled “Piston-split Dual-Fuel Combustion” or PDFC. Tests show that dual-fuel CI engines can simultaneously increase TE and lower NO x and/or soot emissions at high loads through the use of Partial HCCI (PHCCI). At low loads, PHCCI is not possible, but either PDFC or RCCI can be used to further improve NO x and/or soot emissions, albeit at slightly lower TE. These results lead to a “partial dual-fuel” multi-mode strategy of PHCCI at high loads and CDC at low loads, linked together by PDFC. Drive cycle simulations show that this strategy, when tuned to balance NO x and soot reductions, can reduce engine-out CO 2 emissions by about 1% while reducing NO x and soot by about 20% each with respect to CDC. This increases emissions of unburnt hydrocarbons (UHC), still in a treatable range (2.0 g/kWh) but five times as high as CDC, requiring changes in aftertreatment strategy.

Engineering↗

DOE OSTI2026

AOI 5 Improved Efficiency of Medium- and Heavy-Duty Natural Gas and Propane (LPG) Engines

Spark-ignited heavy-duty (HD) natural gas engines typically experience efficiency losses at part-load operation due to throttling requirements needed to maintain stoichiometric combustion. A substantial portion of medium- and heavy-duty engine operation occurs in this low-load region, resulting in increased brake-specific carbon dioxide emissions and reduced overall efficiency. This project designed, developed and demonstrated cylinder deactivation (CDA) technology on an HD natural gas engine to mitigate these losses. CDA enables selective deactivation of cylinders, reducing pumping losses while maintaining required torque output and meeting vehicle noise, vibration, and harshness (NVH) targets. The project objectives were successfully achieved, demonstrating up to 12% improvement in fuel consumption over the next generation HD NG engine on key low loaded HD cycles and maintained compliance with 0.02 g/hp-hr NO x emissions with comparable or better vibrations to current product. These results confirm that CDA technology can substantially improve the fuel efficiency and environmental performance of heavy-duty natural gas engines, reinforcing their potential as a low-carbon bridge solution in the transition toward zero-emission transportation technologies.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2024

Application of a Comprehensive Lagrangian–Eulerian Spark-Ignition Model to Different Operating Conditions

Increasing engine efficiency is essential to reducing emissions, which is a priority for automakers. Unconventional modes such as boosted and highly dilute operation have the potential to increase engine efficiency but suffer from stability concerns and cyclic variability. To aid engineers in designing ignition systems that reduce cyclic variability in such engine operation modes, reliable and accurate spark-ignition models are necessary. Here, in this article, a Lagrangian–Eulerian spark-ignition (LESI) model is used to simulate electrical discharge, spark channel elongation, and ignition in inert or reacting crossflow within a combustion vessel, at different pressures, flow speeds, and dilution rates. First the model formulation is briefly revisited. Then, the experimental and simulations setups are presented. The results showcase the model’s ability to predict the secondary circuit voltage, current, and power signals, in addition to the spark channel elongation, for the inert cases, or flame front growth, for the reacting cases. The results also compare simulation spark channel and flame growth plots to experimental Schlieren images at different instants in time. This work serves to highlight LESI’s ability to predict the characteristics of discharge and ignition across a variety of operating conditions.

42 ENGINEERING↗

DOE OSTI2021

Autoignition of Premixed Liquefied Petroleum Gas in a Rapid Compression Machine: Experimental Results and Chemical Kinetic Mechanism Reduction

Liquefied petroleum gas (LPG) has many properties that make it an attractive alternative fuel such as lower cost than conventional fuels and an established distribution infrastructure. The development of high efficiency, spark ignited LPG engines is currently limited by engine knock and misfire. The knock and misfire limits are further complicated by the wide range of chemical reactivity in LPG, particularly in international markets. In this study, a rapid compression machine (RCM) was used to characterize the effects of variation in LPG fuel reactivity, equivalence ratio, and exhaust gas recirculation (EGR) on autoignition of LPG/oxidizer/inert/EGR blends. Experiments were conducted with 100% propane (C3H8) and blends of propane with propene, ethane, isobutane, and n-butane. EGR was simulated with mixtures of Ar, CO2, CO, and NO at substitution percentages from 0 to 30 mass percent. Equivalence ratio was varied from 0.75 to 1.5. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures and temperatures of 23 to 25 bar and 701 to 921 K, respectively. Zero-dimensional simulations of the RCM experiments were performed using Chemkin with several detailed chemical kinetic mechanisms to determine their suitability at predicting ignition delay periods. Multiple reduced chemical kinetic mechanisms were created from the NUIGMech1.1 mechanism to determine the optimal balance between accuracy and computational efficiency for future three-dimensional, time-dependent spark-ignited engine computations.

42 ENGINEERING↗

DOE OSTI2024

Performance and Emissions of an SI Engine Fueled With DME-Propane Blends

Dimethyl Ether (DME) is an alternative fuel that can be produced renewably and has the potential for lower CO and NOx emissions than conventional petroleum-based fuels. Blending DME with another gaseous fuel such as propane, which has a lower knock tendency than gasoline, can allow this fuel to be leveraged on SI engines. In this study, the use of DME-propane blends on a spark ignition (SI) engine was studied via computer simulations in order to understand the impact on engine performance and emissions and to identify the knock limitations of using such fuel blends. A 2L Hyundai SI engine was modeled in GT Power and the model was validated by comparing it with computational fluid dynamics (CFD) simulation results. Starting from pure propane, DME was added incrementally until knock was observed in the engine. Results indicate that it is feasible to run propane with DME percentages up to 35% before severe knock impacts were observed. The BTE was higher, but the BSFC also increased for DME-propane blends as compared to gasoline. Here, an increase in NOx emissions was detected along with a significant decrease in CO emissions. CO 2 emissions declined for propane as compared to gasoline but increased with the addition of DME.

alternative fuels↗

DOE OSTI2022

Investigations into EGR dilution tolerance in a pre-chamber ignited GDI engine

EGR is a useful means to improve fuel economy in spark-ignited gasoline engines, especially under part-load conditions by means of reducing throttling losses. There is also a significant reduction in NOx emissions due to the reduced peak cylinder temperatures. However, the ability of conventional spark ignition systems to reliably ignite dilute mixtures limits the dilution tolerance due to the onset of combustion instability. In this study, an active pre-chamber system was evaluated at part load condition with various EGR rates using a regular grade full boiling range gasoline. A premixed air-fuel mixture was supplied to the pre-chamber, which assists in scavenging the residual mass fractions to enable reliable ignition of EGR dilute mixtures in the main combustion chamber. A range of pre-chamber injection, air-fuel mixture formulation, and ignition timing strategies were evaluated during the EGR sweeps. In addition, 0-D and 1-D simulations were conducted in GT-Power to assess the thermodynamic state and composition in the pre-chamber, as well as estimate the jet momentum at the various dilution rates. The active pre-chamber extended the EGR dilution limit from 20% for conventional SI to above 30%, with a higher pre-chamber flow rate (more scavenging) resulting in increased combustion stability. A tradeoff between the jet momentum and spark timing was observed when analyzing the GT-Power simulations and the pre-chamber jet momentum was found to decrease with increasing EGR rate. At unstable high EGR operation, no relation could be found between the pre-chamber indicated data and main chamber combustion stability.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2020

Development of a Physics-Based Combustion Model for Engine Knock Prediction

The objective of this project is to improve the prediction of engine knock by developing a new combustion modeling framework. Engine knock is a limiting factor to constrain the increase of fuel efficiency for spark ignition (SI) engines in most passenger cars. Efforts to increase fuel efficiency, increasing the compression ratio or downsizing, lead to the increase in the tendency of the knock occurrence. The knock is an undesired ignition of the end-gas, unburned fuel/air mixture ahead of the spark-ignited premixed flame, resulting in rapid in-cylinder pressure rises and engine damages. The combustion modeling framework developed in this project can consider turbulence-chemistry interactions during end-gas ignition, while using a reasonably detailed chemical mechanism developed for ignition and combustion reactions under engine relevant conditions, and the subtle characteristics of spark-ignited flame propagation. It is developed in the context of large eddy simulation (LES), which can capture stochastic in-cylinder processes. The developed model is incorporated into a commercial software for engine simulation, CONVERGE CFD, as a user defined function, and validated. Engine knock and knock-free experiments as well as direct numerical simulation (DNS) of end-gas ignition in homogeneous turbulence are performed to help model development and provide data sets for model validation. With further validation, the developed model is expected to advance the predictive capability for engine knock simulations and thus contribute to improving the fuel efficiency.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Development of a Physics-Based Combustion Model for Engine Knock Prediction

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Spark-ignited direct-injection engine combustion systems

A direct-injection stratified charge internal combustion engine includes a combustion cylinder to receive an air-fuel mixture, and an air intake port to inlet air into the combustion cylinder. The direct-injection engine also includes a fuel injector configured to deliver fuel within the cylinder in a spray pattern substantially aligned to a cylinder central axis to create the air-fuel mixture. A spark igniter is located within a path of the spray pattern to ignite combustion of the air-fuel mixture. The direct-injection engine further includes a movable piston defining a lower boundary of the combustion cylinder to contain the combustion of the air-fuel mixture. The piston is configured to include a bowl portion having local geometric features located on an intake port side of the combustion cylinder to redirect fluid flow towards a vortex in fluid communication with a combustion location near the cylinder central axis.

42 ENGINEERING↗

DOE OSTI2022

FOULING MITIGATION FOR LASER IGNITERS IN NATURAL GAS ENGINES

Due to several recent developments in lasers and optics, laser igniters can now be designed to be (i) compact so as to have the same footprint as a standard spark plug, (ii) have low power draw, usually less than 50 Watts, and (iii) have vibration and temperature resistance at levels typical of reciprocating engines. Primary advantages of these laser igniters remain (i) extension of lean or dilution limits for ignition of combustible mixtures, and (ii) improved ignition at higher pressures. Recently, tests performed in a 350 kW six-cylinder stationary natural gas reciprocating engine retrofitted with these igniters showed an extension of the operational envelope to yield efficiency improvements of the order of 2.6% points while being compliant with the mandated emission regulations. Even though laser igniters offer promise, fouling of the final optical element that introduces the laser into the combustion chamber is of concern. After performing a thorough literature search, a test plan was devised to evaluate various fouling mitigation strategies. The final approach that was used is a combination of three strategies and helped sustain an optical transmissivity exceeding 98% even after 1500 h of continuous engine operation at 2400 rpm. Based on the observed trend in transmissivity, it now appears that laser igniters can last up to 6000 h of continuous engine operation in a stationary engine running at 1800 rpm.

spark ignited engines, laser ignition, natural gas↗

DOE OSTI2022

A Study of Propane Combustion in a Spark-Ignited Cooperative Fuel Research (CFR) Engine

Liquefied petroleum gas (LPG), whose primary composition is propane, is a promising candidate for heavy-duty vehicle applications as a diesel fuel alternative due to its CO 2 reduction potential and high knock resistance. To realize diesel-like efficiencies, spark-ignited LPG engines are proposed to operate near knock-limit over a wide range of operating conditions, which necessitates an investigation of fuel-engine interactions that leads to end-gas autoignition with propane combustion. This work presents both experimental and numerical studies of stoichiometric propane combustion in a sparkignited (SI) cooperative fuel research (CFR) engine. Engine experiments are initially conducted at different compression ratio (CR) values, and the effects of CR on engine combustion are characterized. A three-pressure analysis (TPA) model based on the two-zone combustion concept is developed in GT-Power and validated using test results to estimate in-cylinder wall temperatures, residual gas fraction, etc. This model is further utilized to examine end-gas chemistry by enabling the SI turbulent flame combustion and unburned gas chemical kinetics modules. Finally, a three-dimensional (3D) computational fluid dynamic (CFD) model of the CFR engine is developed in CONVERGE, where the G-equation and SAGE detailed chemical kinetics models are implemented for combustion modeling. Here, a 153 species reduced chemical kinetics mechanism derived from the detailed NUIGMech1.1 mechanism based on the ignition delay and laminar flame speed (LFS) studies is used to generate an LFS lookup table and to describe end-gas autoignition chemistry. Multi-cycle Reynolds-averaged Navier-Stokes (RANS) simulations are then performed for the tested CRs, and the numerical model is shown to be capable of predicting the propane combustion characteristics, particularly the end-gas autoignition behavior.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2021

End-gas autoignition fraction and flame propagation rate in laser-ignited primary reference fuel mixtures at elevated temperature and pressure

Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.

42 ENGINEERING↗

DOE OSTI2021

Simulations of Multi-Mode Combustion Regimes Realizable In a Gasoline Direct Injection Engine

Lean and dilute gasoline compression ignition (GCI) operation in spark ignition (SI) engines are an attractive strategy to attain high fuel efficiency and low NOx levels. However, this combustion mode is often limited to low-load engine conditions due to the challenges associated with autoignition controllability. In order to overcome this constrain, multi-mode (MM) operating strategies, consisting of advanced compression ignition (ACI) at low load and conventional SI at high load, have been proposed. In this three-dimensional computational fluid dynamics study, the concept of multi-mode combustion using two RON98 gasoline fuel blends (Co-Optima Alkylate and E30) in a gasoline direct injection (GDI) engine were explored. To this end, a new reduced mechanism for simulating the kinetics of E30 fuel blend is introduced in this study. To cover the varying engine load demands for multi-mode engines, primary combustion dynamics observed in ACI and SI combustion modes was characterized and validated against experimental measurements. In order to implement part-load conditions, a strategy of mode transition between SI and ACI combustion (i.e., mixed-mode combustion) was then explored numerically by creating a virtual test condition. The results obtained from the mixed-mode simulations highlight an important feature that deflagrative flame propagation regime coexists with ignition-assisted end-gas autoignition. This study also identifies a role of turbulent flow property adjacent to premixed flame front in characterizing the mixed-mode combustion. The employed hybrid combustion model was verified to perform simulations aiming at suitable range of multi-mode engine operations.

Kim, Sayop↗