Search NASA⌕ Search

SEARCH · Search NASA

Results for “stability selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Magnesium Battery Electrolytes with Improved Oxidative Stability Enabled by Selective Solvation in Fluorinated Solvents

Practical Mg batteries require electrolytes that are stable both toward reduction by Mg metal and oxidation by high voltage cathodes. State-of-the-art Mg electrolytes based on weakly-coordinating Mg salts utilize standard ether-type solvents (usually glymes) due to their reductive stability. However, the oxidative stabilities of these solvents are less than ideal, leading to difficulties in realizing the high oxidative stabilities of novel salts. On the other hand, alternative solvents with greater oxidative stability are typically unable to support Mg cycling. Here, in this work, we report a selective solvation approach involving the combination of glyme and hydrofluoroether solvents. Selective solvation of Mg 2+ by the glyme solvent component increases the oxidative stability of the glyme while maintaining sufficient reductive stability of the noncoordinating hydrofluoroether. We show that this approach enables the design of electrolytes with greater oxidative stability than glyme-only electrolytes while retaining enough reductive stability to cycle Mg metal. We also relate the influence of various coordination interactions among the solvents and anions with Mg 2+ to their electrochemical stabilities to better inform the design of future electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2015

Enhancing the stability of copper chromite catalysts for the selective hydrogenation of furfural with ALD overcoating (II) – Comparison between TiO2 and Al2O3 overcoatings

TiO2 atomic layer deposition (ALD) overcoatings were applied to copper chromite catalysts to increase the stability for 2-furfuraldehyde (“furfural”) hydrogenation. After overcoating, about 75% activity was preserved compared to neat copper chromite: much higher activity than an alumina ALD overcoated catalyst with a similar number of ALD cycles. The effects of ALD TiO2 on the active Cu nanoparticles were studied extensively using both in-situ TPR/isothermal-oxidation and in-situ furfural hydrogenation via Cu XAFS. The redox properties of Cu were modified only slightly by the TiO2 ALD overcoat. However, a subtle electronic interaction was observed between the TiO2 ALD layers and the Cu nanoparticles. With calcination at 500 °C the interaction between the TiO2 overcoat and the underlying catalyst is strong enough to inhibit migration and site blocking by chromite, but is sufficiently weaker than the interaction between the Al2O3 overcoat and copper chromite that it does not strongly inhibit the catalytic activity of the copper nanoparticles.

Zhang, Hongbo↗
DOE OSTI2018

A Dynamically Stabilized Single‐Nickel Electrocatalyst for Selective Reduction of Oxygen to Hydrogen Peroxide

Abstract On‐location electrochemical generation of H 2 O 2 is of great current interest. Herein, selective two‐electron reduction of O 2 to H 2 O 2 by a single [Ni II (H 2 O) 6 ] 2+ cation that is dynamically associated with a negatively charged metal–organic layer (MOL) by hydrogen bonding and coulombic interactions is reported. In contrast, Ni II centers covalently immobilized on the MOL reduce O 2 to H 2 O in a four‐ electron process. Oxygen adsorption by [Ni II (H 2 O) 6 ] 2+ followed by two‐electron reduction generates neutral [Ni II (H 2 O) 4 (OH)(OOH)] 0 , which momentarily disconnects from the negatively charged MOL to avoid the injection of additional electrons. Release of H 2 O 2 from [Ni II (H 2 O) 4 (OH)(OOH)] 0 regenerates [Ni II (H 2 O) 6 ] 2+ , which regains affinity to the MOL. Such dynamically associated Ni II single‐metal electrocatalysts ensure high selectivity and represent a new strategy for generating selective catalysts for electrochemical production of important chemicals.

Wang, Tingting↗
DOE OSTI2023

Stabilized hole-selective layer for high-performance inverted p-i-n perovskite solar cells

P-i-n geometry perovskite solar cells (PSCs) offer simplified fabrication, greater amenability to charge extraction layers, and low-temperature processing over n-i-p counterparts. Self-assembled monolayers (SAMs) can enhance the performance of p-i-n PSCs but ultrathin SAMs can be thermally unstable. Here we report a thermally robust hole-selective layer comprised of nickel oxide (NiO x ) nanoparticle film with a surface-anchored (4-(3,11-dimethoxy-7H-dibenzo[c,g]carbazol-7-yl)butyl)phosphonic acid (MeO-4PADBC) SAM that can improve and stabilize the NiO x /perovskite interface. The energetic alignment and favorable contact and binding between NiO x /MeO-4PADBC and perovskite reduced the voltage deficit of PSCs with various perovskite compositions and led to strong interface toughening effects under thermal stress. The resulting 1.53–electron-volt devices achieved 25.6% certified power conversion efficiency and maintained >90% of their initial efficiency after continuously operating at 65 degrees Celsius for 1200 hours under 1-sun illumination.

14 SOLAR ENERGY↗
DOE OSTI2013

Systematic modulation and enhancement of CO{sub 2} : N{sub 2} selectivity and water stability in an isoreticular series of bio-MOF-11 analogues

An isoreticular series of cobalt-adeninate bio-MOFs (bio-MOFs 11-14) is reported. The pores of bio-MOFs 11-14 are decorated with acetate, propionate, butyrate, and valerate, respectively. The nitrogen (N{sub 2}) and carbon dioxide (CO{sub 2}) adsorption properties of these materials are studied and compared. The isosteric heats of adsorption for CO{sub 2} are calculated, and the CO{sub 2}:N{sub 2} selectivities for each material are 10 determined. As the lengths of the aliphatic chains decorating the pores in bio-MOFs 11-14 increase, the BET surface areas decrease from 1148 m{sup 2}/g to 17 m{sup 2}/g while the CO{sub 2}:N{sub 2} selectivities predicted from ideal adsorbed solution theory at 1 bar and 273 K for a 10:90 CO{sub 2}:N{sub 2} mixture range from 73:1 for bio-MOF-11 to 123:1 for bio-MOF-12 and finally to 107:1 for bio-MOF-13. At 298 K, the selectivities are 43:1 for bio-MOF-11, 52:1 for bio-MOF-12, and 40:1 for bio-MOF-13. Additionally, it is shown that 15 bio-MOF-14 exhibits a unique molecular sieving property that allows it to adsorb CO{sub 2} but not N{sub 2} at 273 and 298 K. Finally, the water stability of bio-MOFs 11-14 increases with increasing aliphatic chain length. Bio-MOF-14 exhibits no loss of crystallinity or porosity after soaking in water for one month.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

First Principles Prediction of Structure, Structure Selectivity, and Thermodynamic Stability under Realistic Conditions

Novel materials are often the enabler for new energy technologies. In ab-initio computational materials science, method are developed to predict the behavior of materials starting from the laws of physics, so that properties can be predicted before compounds have to be synthesized and tested. As such, a virtual materials laboratory can be constructed, saving time and money. The objectives of this program were to develop first-principles theory to predict the structure and thermodynamic stability of materials. Since its inception the program focused on the development of the cluster expansion to deal with the increased complexity of complex oxides. This research led to the incorporation of vibrational degrees of freedom in ab-initio thermodynamics, developed methods for multi-component cluster expansions, included the explicit configurational degrees of freedom of localized electrons, developed the formalism for stability in aqueous environments, and culminated in the first ever approach to produce exact ground state predictions of the cluster expansion. Many of these methods have been disseminated to the larger theory community through the Materials Project, pymatgen software, or individual codes. We summarize three of the main accomplishments.

36 MATERIALS SCIENCE↗
DOE OSTI2015

A high-performance spectrally-selective solar absorber based on a yttria-stabilized zirconia cermet with high-temperature stability

Spectrally-selective solar absorbers are widely used in solar hot water and concentrating solar power (CSP) systems. However, their performance at high temperatures (>450 °C) is still not satisfactory due to high infrared (IR) emittance and lack of long-term thermal stability. In this work, we explore yttria-stabilized zirconia (YSZ) cermet-based spectrally-selective surfaces for high-temperature solar absorber applications. The developed multilayer selective surface comprises two sunlight-absorbing W–Ni–YSZ cermet layers with different W–Ni volume fractions inside the YSZ matrix, two anti-reflection coatings (ARCs), and one tungsten IR reflection layer for reduced IR emittance and improved thermal stability, deposited on a polished stainless steel (SS) substrate. The fabricated solar absorbers are tested for their long-term thermal stability at 600 °C. We find a distinct change in the surface morphology of the solar absorbers when oxygen is highly deficient in the YSZ-ARC layers. The oxygen deficiency can be effectively overcome through increasing the oxygen partial pressure during sputtering, which leads to a stable solar absorber with a solar absorptance of ~0.91 and a total hemispherical emittance of ~0.13 at 500 °C. Those values are obtained at the actual operating temperature using an absolute and direct method that measures the total hemispherical emittance with high accuracy. In contrast, most reports on solar absorber development in the literature to date use only near room-temperature spectroscopy techniques that have been shown to significantly underestimate the total hemispherical emittance. This makes our experimentally demonstrated total hemispherical emittance value the lowest ever reported for a high-temperature stable solar absorber with solar absorptance above 0.9.

14 SOLAR ENERGY↗
DOE OSTI2019

Photocatalytic Facet Selectivity in BiVO 4 Nanoparticles: Polaron Electronic Structure and Thermodynamic Stability Considerations for Photocatalysis

Selective charge separation among different crystal facets of a semiconductor is an intriguing phenomenon for which there is no firm and full theoretical foundation currently. In this work, we report on a density functional theory + U characterization of band alignment and electron and hole polaron stabilities among the (010), (110), and (011) facets of bismuth vanadate BiVO 4 (BVO). Computation-derived band alignment indicates that the conduction band minima are at nearly the same level among the three facets but that the valence band maxima exhibit a shift. We also modeled electron and hole polarons as localized electrons and holes on vanadium and oxygen, respectively, and determined their relative stabilities from a “bulk” region to a surface region. Calculated stabilities reveal similar stability profiles across the various facets, with electron polarons most stable when localized on subsurface V atoms and hole polarons most stable on surface O atoms. Calculations indicate a small stability preference for electron polarons toward the (011) facet and for hole polarons toward the (110) facet, whereas, experimentally, interfacial reduction is observed to take place selectively on the (010) facet and oxidation on the (110) and (011) facets. Facet selectivity could be occurring on the basis of thermodynamics (electron or holes showing a stronger affinity for some facets over others) or kinetics (electron or hole transport and/or redox processes being more efficient toward/on some facets over others) or a combination of both. This work establishes that thermodynamic stability alone is not responsible for the observed facet selectivity in BVO. Furthermore, we surmise that polaron transport kinetics and interfacial redox kinetics are likely to have a role in facet selectivity in BVO. These issues will be the subject of future publications.

14 SOLAR ENERGY↗
DOE OSTI2023

Insights into palladium poisoning of Cu/SSZ-13 selective catalytic reduction catalysts

Here, the impacts of Pd poisoning to the activity, selectivity, and hydrothermal stability of Cu/SSZ-13 selective catalytic reduction (SCR) catalysts are reported. Pd lowers DeNOx efficiency of Cu/SSZ-13 via two mechanisms: (1) displacing SCR active sites in the form of isolated Pd-ions, and (2) catalyzing non-selective NH 3 oxidation in the form of PdO. The first mechanism works by the diffusion of isolated Pd-ions into chabazite cages to displace ZCu II OH SCR active species, and it occurs on Cu/SSZ-13 catalysts with and without external surface CuO clusters in similar fashion. In contrast, the second mechanism works differently with and without external surface CuO clusters. For Cu/SSZ-13 catalyst without external CuO clusters (i.e., primarily isolated Cu-ions), PdO leads to significant decrease of DeNOx efficiency at reaction temperatures above ~400°C due to its non-selective NH 3 oxidation activity at high temperatures. However, this poisoning effect becomes much less impactful on Cu/SSZ-13 catalyst containing CuO clusters. This is due to the formation of CuO-PdO solid solution via interactions between CuO and PdO, which reduces non-selective NH 3 oxidation potential. Furthermore, this solid solution formation even mitigates adverse effects caused by hydrothermal aging. Hence, the poisoning effects of Pd are closely related to Cu speciation and spatial distribution of a Cu/SSZ-13 catalyst. Finally, this study suggests a strategy in eliminating Pd poisoning, that is, the introduction of an oxide phase that effectively traps PdO but does not adversely influence SCR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Self‐Stabilized Heterometallic Pair Sites for Selective Ethanol Dehydrogenation on Pt–Cr–Ag Alloy Catalysts

Self‐stabilized, heterometallic pair‐sites can enable fine‐tuning of catalytic functionality while also mitigating dynamic structural changes that degrade catalytic performance. This study demonstrates the development and characterization of trimetallic Pt x Cr x Ag 1‐2x ( x ≤ 0.1) alloys with active Pt–Cr pair‐ensembles for non‐oxidative ethanol dehydrogenation, leveraging predictions that favorable bonding stabilizes Pt–Cr pairs diluted in Ag. Operando X‐ray absorption spectroscopy confirms the preferential formation and stability of Pt–Cr pairings dispersed throughout the Ag matrix, and ambient‐pressure X‐ray photoelectron spectroscopy shows that Pt–Cr sites have significant activity for ethanol dehydrogenation, while suppressing reaction processes that deactivate binary Pt–Ag and Cr–Ag alloys. This work demonstrates that stabilizing heterometallic pair sites within trimetallic alloys provides a new avenue for designing catalysts with discrete active sites that are durable and highly selective.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Enhanced Thermal Stability of W-Ni-Al 2 O 3 Cermet-Based Spectrally Selective Solar Absorbers with Tungsten Infrared Reflectors

Solar thermal technologies such as solar hot water and concentrated solar power trough systems rely on spectrally selective solar absorbers. These solar absorbers are designed to efficiently absorb the sunlight while suppressing re-emission of infrared radiation at elevated temperatures. Efforts for the development of such solar absorbers must not only be devoted to their spectral selectivity but also to their thermal stability for high temperature applications. In this work, selective solar absorbers based on two cermet layers are fabricated on mechanically polished stainless steel substrates using a magnetron sputtering technique. The targeted operating temperature is 500–600 °C. A detrimental change in the morphology, phase, and optical properties is observed if the cermet layers are deposited on a stainless steel substrate with a thin nickel adhesion layer, which is due to the diffusion of iron atoms from the stainless steel into the cermet layer forming a FeWO 4 phase. In order to improve thermal stability and reduce the infrared emittance, tungsten is found to be a good candidate for the infrared reflector layer due to its excellent thermal stability and low infrared emittance. Lastly, a stable solar absorptance of ≈0.90 is demonstrated, with a total hemispherical emittance of 0.15 at 500 °C.

14 SOLAR ENERGY↗
DOE OSTI2022

Role of Metal Selection in the Radiation Stability of Isostructural M-UiO-66 Metal–Organic Frameworks

Robust and versatile metal–organic frameworks (MOFs) have emerged as sophisticated scaffolds to meet the critical needs of the nuclear community, but their performance depends on their underexplored structural integrities in high- radiation fields. The contributions of selected metal nodes in the radiation stability of MOFs within the isostructural M-UiO-66 series (where M = Zr, Ce, Hf, Th, and Pu; Zr-UiO-66 experiments were executed in a previous work) have been determined. Ce-, Hf-, and Th-UiO-66 MOF samples were irradiated via gamma and He-ion methodologies to obtain doses up to 3 MGy and 85 MGy, respectively, the latter strikingly higher than that obtained in most other studies. Appreciable self-irradiation constituted the total absorbed doses, up to 31 MGy of the gamma-irradiated Pu-UiO-66 samples. Structural degradation was ascertained by powder X-ray diffraction, X-ray total scattering, vibrational spectroscopy, and, where possible, N 2 physisorption isotherms. Diffuse reflectance infrared Fourier transform spectroscopy provided atomic-level mechanistic insights to reveal that the node-linker connection was most susceptible to radiation damage. Density functional theory calculations were performed on cluster models to evaluate the binding energy of the linkers to each metal node. Here, while the isostructures disclosed the same breakdown signatures, distinct radiation sensitivity as a function of metal selection was evident and followed the trend Hf-UiO-66 ~ Zr-UiO-66 > Th-UiO-66 > Pu-UiO-66 > Ce-UiO-66. We anticipate that these endeavors will contribute to the rational design of radiation-resistant materials for targeted applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗