Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface samples”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Three-omega thermal-conductivity measurements with curved heater geometries

The three-omega method, a powerful technique to measure the thermal conductivity of nanometer-thick films and the interfaces between them, has historically employed straight conductive wires to act as both heaters and thermometers. When investigating stochastically prepared samples such as two-dimensional materials and nanomembranes, residue and excess material can make it difficult to fit the required millimeter-long straight wire on the sample surface. There are currently no available criteria for how diverting three-omega heater wires around obstacles affects the validity of the thermal measurement. In this Letter, we quantify the effect of the wire curvature by performing three-omega experiments with a wide range of frequencies using both curved and straight heater geometries on SiO 2 /Si samples. When the heating wire is curved, we find that the measured Si substrate thermal conductivity changes by only 0.2%. Similarly, we find that wire curvature has no significant effect on the determination of the thermal resistance of an ~65 nm SiO 2 layer, even for the sharpest corners considered here, for which the largest measured ratio of the thermal penetration depth of the applied thermal wave to radius of curvature of the heating wire is 4.3. This result provides useful design criteria for three-omega experiments by setting a lower bound for the maximum ratio of the thermal penetration depth to wire radius of curvature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Reexamining circular dichroism in photoemission from a topological insulator

The orbital angular momentum (OAM) of electron states is an essential ingredient for topological and quantum geometric quantities in solids. For example, Dirac surface states with helical spin- and orbital-angular momenta are a hallmark of a 3D topological insulator. Angle-resolved photoemission spectroscopy (ARPES) with variable circular light polarization, known as circular dichroism (CD), has been assumed to be a direct probe of OAM and, by proxy, of the Berry curvature of electronic bands in energy- and momentum-space. Indeed, topological surface states have been shown to exhibit angle-dependent CD (CDAD), and more broadly, CD is often interpreted as evidence of spin-orbit coupling. Meanwhile, it is well-established that CD originates from the photoemission matrix elements, which can have extrinsic contributions related to the experimental geometry and the inherently broken inversion symmetry at the sample surface. Therefore, it is important to broadly examine CD-ARPES to determine the scenarios in which it provides a robust probe of intrinsic material physics. We performed CD-ARPES on the canonical topological insulator Bi 2 ⁢Se 3 over a wide range of incident photon energies. Not only do we observe angle-dependent CD in the surface states, as expected, but we also find CD of a similar magnitude in virtually all bulk bands. Since OAM is forbidden by inversion symmetry in the bulk, we conclude this originates from symmetry-breaking in the photoemission process. Comparison with theoretical calculations supports this view and suggests that “hidden” OAM—localized to atomic sites within each unit cell—contributes significantly. Additional effects, including inter-atomic interference and final-state resonances, are responsible for the rapid variation of the CDAD signal with photon energy.

Sidilkover, Ittai [Tel Aviv University, Tel Aviv (↗
DOE OSTI2025

Reexamining Circular Dichroism in Photoemission From a Topological Insulator

The orbital angular momentum (OAM) of electron states is an essential ingredient for topological and quantum geometric quantities in solids. For example, Dirac surface states with helical spin- and orbital-angular momenta are a hallmark of a 3D topological insulator. Angle-resolved photoemission spectroscopy (ARPES) with variable circular light polarization, known as circular dichroism (CD), has been assumed to be a direct probe of OAM and, by proxy, of the Berry curvature of electronic bands in energy- and momentum-space. Indeed, topological surface states have been shown to exhibit angle-dependent CD (CDAD), and more broadly, CD is often interpreted as evidence of spin-orbit coupling. Meanwhile, it is well-established that CD originates from the photoemission matrix elements, which can have extrinsic contributions related to the experimental geometry and the inherently broken inversion symmetry at the sample surface. Therefore, it is important to broadly examine CD-ARPES to determine the scenarios in which it provides a robust probe of intrinsic material physics. We performed CD-ARPES on the canonical topological insulator $\mathrm{Bi}_2\mathrm{Se}_3$ over a wide range of incident photon energies. Not only do we observe angle-dependent CD in the surface states, as expected, but we also find CD of a similar magnitude in virtually all bulk bands. Since OAM is forbidden by inversion symmetry in the bulk, we conclude this originates from symmetry-breaking in the photoemission process. Comparison with theoretical calculations supports this view and suggests that $\textit{hidden}$ OAM - localized to atomic sites within each unit cell - contributes significantly. Additional effects, including inter-atomic interference and final-state resonances, are responsible for the rapid variation of the CDAD signal with photon energy.

FOS: Physical sciences↗
DOE OSTI2023

Photoelectrochemical and Photovoltaic Performance of As-deposited Ink-based CuInS 2 Heterojunction Thin Film

In this report, we demonstrate low-temperature ink-based fabrication of CuInS 2 -based photoelectrodes for hydrogen production capable of producing photocurrent densities as high as 8.8mA.cm -2 . In this process, molecular ink made of metal chlorides and thiourea dissolved in methanol was spin coated onto Mo-coated soda lime glass substrates. Samples were then placed on a hot plate (sample surface temperature: 250°C) to induce CuInS 2 formation and remove the solvent and by-products. No further processing, such as high temperature sulfurization, was performed. Further, the CuInS 2 films were then integrated as photocathode for hydrogen evolution by photoelectrodeposition of Pt nanoparticles. Photocurrent density of 0.4mA.cm -2 at 0V vs. RHE was detected from such electrodes. However, samples coated with CdS/ZnO/ITO overlayers forming heterojunction prior to Pt deposition exhibited significant improvement of the photocurrent density, reaching 8.8mA.cm -2 at 0V vs. RHE, highlighting the improved charge transfer by the p-n junction formed at the CuInS 2 /CdS interface. The charge transfer resistance of the CuInS 2 /CdS/ZnO/ITO-Pt photoelectrode was almost 5 times lower than that of the CuInS 2 -Pt photoelectrode as revealed by electrochemical impedance spectroscopy analysis. In addition, the onset potential was shifted by ca. 0.45V toward the anodic direction, reaching 0.75V vs. RHE. Solar cell made of identical structure (Mo/CuInS 2 /CdS/ZnO/ITO) showed power conversion efficiency of 2.1% with short-circuit photocurrent density and open circuit voltage of 7.4mA.cm -2 and 820mV, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The performance of additively manufactured Haynes 282 in supercritical CO 2

The use of supercritical carbon dioxide (sCO 2 ) as a working fluid is garnering interest in next generation power production systems due to the possibility of increased operational efficiencies and lower associated costs. Its implementation requires alloys with excellent high temperature strength and corrosion resistance, which makes Haynes 282® (H282) a suitable candidate. With increasing adoption of additive manufacturing (AM) in the energy industry, there is a need to investigate long-term sCO2 exposure on AM produced materials. Additively manufactured H282 (AM-H282) samples built using laser powder bed fusion in two different orientations were analyzed through imaging, gravimetric analysis, and room-temperature tensile testing before and after 1000-h exposure to CO 2 at 750 °C and 20 MPa. Performed imaging included observation of the sample surfaces and of the material bulk (cross sections) through means of Scanning Electron Microscopy (SEM) and optical microscopy. In comparison to wrought H282, it was found that the exposed material exhibited a similar Cr 2 O 3 oxide protective layer about 2 μm in thickness with additional top-surface TiO 2 oxide and carbon-rich precipitates. It was also similarly observed that internal oxidation was present but limited to a depth of 20 μm, and a 1–3 μm γ’ denuded region appeared to surround all internal and surface oxidation. Thermal aging effects were noted with the precipitation of needle-like structures in the γ/γ’ matrix and a coarsening of the γ’ precipitates from 28 nm to 73 nm. Mass measurements analyzing oxide precipitation revealed a larger increase compared to wrought, representing an approximate 20% difference. Tensile testing results showed similar behavior to wrought with a slight increase in yield strength and a large reduction in elongation in the exposed samples.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Near-Surface Layer Perforations as Precursors to Fracture in Accumulative Roll Bonding of a Multilayered Metal Composite

We use micro-computed tomography (µ-CT) to characterize the sizes, shapes, and locations of layer perforation (LP) defects in laminates of copper (Cu) and tantalum (Ta) processed by accumulative roll bonding (ARB). One—termed Cu/Ta—was processed from an initial stacking of seven alternating Cu and Ta sheets, with the exterior sheets being Cu. In the other—termed Ta/Cu—the exterior sheets are Ta. Cu/Ta remained intact during processing and exhibits an approximately uniform spatial distribution of LPs. By contrast, Ta/Cu fractured by longitudinal splitting. LPs in this latter sample are concentrated near the sample surfaces. Moreover, their density increases with decreasing distance to the fracture surface. Furthermore, these findings show that materials undergoing ARB may remain intact, despite profuse formation of LPs, provided that the LPs are uniformly distributed. However, a non-uniform distribution of LPs is correlated with longitudinal splitting.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Practical guide to understanding goodness-of-fit metrics used in chemical state modeling of x-ray photoelectron spectroscopy data by synthetic line shapes using nylon as an example

Chemical state analysis of a sample surface through fitting bell-shaped curves to x-ray photoelectron spectroscopic polymer data is reviewed using nylon to introduce and discuss aspects of data analysis. Different strategies for modeling chemistry in nylon spectra are presented and in so doing, a case is made to include in published science the design logic and implementation in terms of line shapes and optimization parameter constraints between components in a peak model. Imperfections in line shape relative to the true shape for photoemission lines, when compensated for using constraints to optimization parameters, are shown to provide chemical state information about a sample that justify, for peak models constructed with these limitations, metrics for goodness-of-fit different from those expected for pulse-counted data.

Materials Science↗
DOE OSTI2023

Cinematic reflectometry using QIKR, the quite intense kinetics reflectometer

The Quite Intense Kinetics Reflectometer (QIKR) will be a general-purpose, horizontal-sample-surface neutron reflectometer. Reflectometers measure the proportion of an incident probe beam reflected from a surface as a function of wavevector (momentum) transfer to infer the distribution and composition of matter near an interface. The unique scattering properties of neutrons make this technique especially useful in the study of soft matter, biomaterials, and materials used in energy storage. Exploiting the increased brilliance of the Spallation Neutron Source Second Target Station, QIKR will collect specular and off-specular reflectivity data faster than the best existing such machines. It will often be possible to collect complete specular reflectivity curves using a single instrument setting, enabling “cinematic” operation, wherein the user turns on the instrument and “films” the sample. Samples in time-dependent environments (e.g., temperature, electrochemical, or undergoing chemical alteration) will be observed in real time, in favorable cases with frame rates as fast as 1 Hz. Cinematic data acquisition promises to make time-dependent measurements routine, with time resolution specified during post-experiment data analysis. This capability will be deployed to observe such processes as in situ polymer diffusion, battery electrode charge–discharge cycles, hysteresis loops, and membrane protein insertion into lipid layers.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Bayesian inference in band excitation scanning probe microscopy for optimal dynamic model selection in imaging

The universal tendency in scanning probe microscopy (SPM) over the last two decades is to transition from simple 2D imaging to complex detection and spectroscopic imaging modes. The emergence of complex SPM engines brings forth the challenge of reliable data interpretation, i.e., conversion from detected signals to descriptors specific to tip–surface interactions and subsequently to material’s properties. In this work, we implemented a Bayesian inference approach for the analysis of the image formation mechanisms in band excitation SPM. Compared to the point estimates in classical functional fit approaches, Bayesian inference allows for the incorporation of extant knowledge of materials and probe behavior in the form of corresponding prior distribution and return the information on the material functionality in the form of readily interpretable posterior distributions. We explore the nonlinear mechanical behaviors spatially in a classical ferroelectric material, PbTiO 3 . We observe the non-trivial evolution of the Duffing stiffness term and the nonlinearity of the sample surface, determine spatial clustering of the nonlinear response, and perform a Landau analysis on predicting the nonlinear coefficient, which indicates that ferroelectric behavior can be a cause of the observed results. These observations suggest that the spectrum of anomalous behaviors at the ferroelectric domain walls may be broader than previously believed and can extend to non-conventional mechanical properties in addition to static and microwave conductance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Nanoscale electronic inhomogeneities in 1⁢ T ⁢-TaS 2

Here, we report a set of scanning tunneling microscopy (STM) and spectroscopy (STS) experiments studying native defects in CVT grown 1⁢T–TaS 2 . Six different sample surfaces from four bulk crystals were investigated. Wide area imaging reveals a prevalence of nanometer-scale electronic inhomogeneities due to native defects, with pristine regions interspersed. These inhomogeneities appear in typical as-grown crystals and coexist with a well-formed commensurate charge density wave of 1T–TaS 2 at low temperatures. Electronic inhomogeneities show up both as variations in the apparent height in STM and in the local density of states in STS; the bands can shift by 60 meV and the gap varies by more than 100 meV across inhomogeneities. These inhomogeneities are present in similar concentration across large-scale areas of all samples studied, but do not influence the charge density wave formation on local or global scales. The commensurate charge density wave exhibits long-range order and remains locally intact in the presence of these inhomogeneities.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Direct Visualization and Manipulation of Tunable Quantum Well State in Semiconducting Nb 2 SiTe 4

We report quantum well states (QWSs) can form at the surface or interfaces of materials with confinement potential. They have broad applications in electronic and optical devices such as high mobility electron transistor, photodetector, and quantum well laser. The properties of the QWSs are usually the key factors for the performance of the devices. However, direct visualization and manipulation of such states are, in general, challenging. In this work, by using angle-resolved photoemission spectroscopy (ARPES) and scanning tunneling microscopy/spectroscopy (STM/STS), we directly probe the QWSs generated on the vacuum interface of a narrow band gap semiconductor Nb 2 SiTe 4 . Interestingly, the position and splitting of QWSs could be easily manipulated via potassium (K) dosage onto the sample surface. Our results suggest Nb 2 SiTe 4 to be an intriguing semiconductor system to study and engineer the QWSs, which has great potential in device applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Laser Ablation-Capillary Absorption Spectroscopy: A novel approach for high throughput and increased spatial resolution measurements of δ 13 C in plant-soil systems

Spatial and temporal heterogeneity of nutrient exchange within the rhizosphere is a topic of increasing interest, although challenging to study due to limits in existing analytical capabilities. Here, we developed and demonstrated a new approach applying laser ablation sample introduction to capillary absorption spectroscopy (LA-CAS) to characterize carbon isotopic distribution within plant tissues, rhizosphere, and soil. We exposed switchgrass plants to 13 CO 2 to allow tracing of 13 C-labelled photosynthates within plant biomass and into the associated soil. The LA-CAS methods we describe leverage continuous measurements of a sample stream derived from laser ablation line scans (10-25 µm in width) over a sample surface which enables the user to produce an isotope map with a) higher data density or b) over larger spatial areas versus previously existing techniques. This versatility of LA-CAS is assessed through testing of a range of laser parameters (spot size, scan rates) on various materials (soil, plant biomass/tissues, and rhizosphere). Here, we demonstrate the ability of LA-CAS to provide near instantaneous $δ$ 13 C measurements over isotopically distinct surfaces to enable high spatially resolved mapping of 13 C-labelled material within the rhizosphere. Applying LA-CAS analysis to plant biomass, we observed higher $δ$ 13 C values concentrated within phloem structures, consistent with localized photosynthate transport. When mapping across the rhizosphere, 13 C-enriched soil was typically present within 5-10µm of root boundaries with a steep spatial increase in $δ$ 13 C when the scan approached the middle of the root. As with all LA approaches, care is required to ensure accurate results as phenomena linked to ablation, combustion, and isotopic measurement can impart artifacts if not carefully controlled. Still, taken as a whole, our demonstrations highlight the increased sample throughput, improved data density, and enhanced $δ$ 13 C capability of LA-CAS versus other LA techniques and emphasize the role this method can play in future plant and rhizosphere related studies.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Fracture‐Resistant and Thermally Insulating Ultrahigh‐Temperature Carbide Foams

Dense ultrahigh‐temperature ceramics (UHTCs) carbides are recognized as potential materials for thermal protection systems (TPS) owing to properties beyond existing structural materials’ capabilities. Recent advances in UHTCs have enabled the development of multiscale porous microstructures. Herein, it is highlighted that the porosity in UHTCs are no longer treated as a defect but as a functional property specifically tailored for thermal insulation. It is a promising solution to design and fabricate bulk UHTC foams via a freeze‐drying (FD) approach followed by calibrated pressureless spark plasma sintering. Herein, monolithic TaC and HfC UHTC foams and their composite show the partial solid–solution formation of (Ta, Hf)C with porosity ≥50%. TaC–HfC foam (≈80–92 N) shows an intermediate load‐bearing capability compared to monolithic TaC (≈120–135 N) and HfC (≈28–35 N) foams, with no evident cracking on the sample surface. The thermal conductivity of partial solid‐solution TaC–HfC foam increases up to fivefold compared to parent UHTC foams. In the results, solid solutions’ efficacy and pores’ unidirectionality in providing thermal insulation to TaC–HfC while maintaining its high‐load bearing capability are illustrated. In conclusion, the developed technique establishes a new paradigm shift in UHTCs, expanding their potential for TPS in extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanoscale Antiferromagnetic Domain Imaging using Full-Field Resonant X-ray Magnetic Diffraction Microscopy

The physical properties of magnetic materials frequently depend not only on the microscopic spin and electronic structures, but also on the structures of mesoscopic length scales that emerge, for instance, from domain formations, or chemical and/or electronic phase separations. However, experimental access to such mesoscopic structures is currently limited, especially for antiferromagnets with net zero magnetization. Here, full-field microscopy and resonant magnetic X-ray diffraction are combined to visualize antiferromagnetic (AF) domains of the spin–orbit Mott insulator Sr 2 IrO 4 with area over ≈0.1 mm 2 and with spatial resolution as high as ≈150 nm. With the unprecedented wide field of views and high spatial resolution, an intertwining of two AF domains on a length comparable to the measured average AF domain wall width of 545 nm is revealed. This mesoscopic structure comprises a substantial portion of the sample surface, and thus can result in a macroscopic response unexpected from its microscopic magnetic structure. In particular, the symmetry analysis presented in this work shows that the inversion symmetry, which is preserved by the microscopic AF order, becomes ill-defined at the mesoscopic length scale. We report this result underscores the importance of this novel technique for a thorough understanding of the physical properties of antiferromagnets.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Top-Down Fabrication of Atomic Patterns in Twisted Bilayer Graphene

Atomic-scale engineering typically involves bottom-up approaches, leveraging parameters such as temperature, partial pressures, and chemical affinity to promote spontaneous arrangement of atoms. These parameters are applied globally, resulting in atomic-scale features scattered probabilistically throughout the material. In a top-down approach, different regions of the material are exposed to different parameters, resulting in structural changes varying on the scale of the resolution. In this work, the application of global and local parameters is combined in an aberration-corrected scanning transmission electron microscope (STEM) to demonstrate atomic-scale precision patterning of atoms in twisted bilayer graphene. The focused electron beam is used to define attachment points for foreign atoms through the controlled ejection of carbon atoms from the graphene lattice. The sample environment is staged with nearby source materials such that the sample temperature can induce migration of the source atoms across the sample surface. Under these conditions, the electron-beam (top-down) enables carbon atoms in the graphene to be replaced spontaneously by diffusing adatoms (bottom-up). Using image-based feedback control, arbitrary patterns of atoms and atom clusters are attached to the twisted bilayer graphene with limited human interaction. Finally, the role of substrate temperature on adatom and vacancy diffusion is explored by first-principles simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Spatially Distributed Ramp Reversal Memory in VO 2

Ramp‐reversal memory has recently been discovered in several insulator‐to‐metal transition materials where a non‐volatile resistance change can be set by repeatedly driving the material partway through the transition. This study uses optical microscopy to track the location and internal structure of accumulated memory as a thin film of VO 2 is temperature cycled through multiple training subloops. These measurements reveal that the gain of insulator phase fraction between consecutive subloops occurs primarily through front propagation at the insulator‐metal boundaries. By analyzing transition temperature maps, it is found, surprisingly, that the memory is also stored deep inside both insulating and metallic clusters throughout the entire sample, making the metal‐insulator coexistence landscape more rugged. This non‐volatile memory is reset after heating the sample to higher temperatures, as expected. Diffusion of point defects is proposed to account for the observed memory writing and subsequent erasing over the entire sample surface. By spatially mapping the location and character of non‐volatile memory encoding in VO 2 , this study results enable the targeting of specific local regions in the film where the full insulator‐to‐metal resistivity change can be harnessed in order to maximize the working range of memory elements for conventional and neuromorphic computing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Geochemical assessment of mineral sequestration of carbon dioxide in the midcontinent rift

Abstract This study examines the potential of Midcontinent Rift rocks to facilitate long‐term CO 2 sequestration by providing the necessary Ca and Mg for carbonate mineralization. Surface samples were collected from the Oronto and Bayfield‐Jacobsville Groups around Lake Superior and used for petrography and X‐ray diffraction to determine their mineral composition. Also, X‐ray fluorescence was also used to assess their bulk chemical composition. The samples were then exposed to CO 2 and deionized water in Teflon‐lined vessels at 90°C, and the resulting leachate fluids were analyzed for the cation released during the testing. SEM microscopy was used to examine the samples for potential mineralization of carbonate minerals. The Oronto Group sediments consist primarily of feldspathic to feldspathic lithic arenites with a chlorite‐dominated matrix, and the primary porosity is blocked by calcite and hematite cement. The Bayfield–Jacobsville sequences are porous quartz arenites to feldspathic quartz arenites that do not contain significant accumulation of Ca‐, Mg‐, and Fe‐bearing minerals. The leachate fluids obtained from Oronto Group samples exhibit a maximum Ca release rate (5.2 × 10 −4 mole/cm 2 .day), indicating rapid calcite cement dissolution and increased porosity and permeability. SEM/EDS microanalysis revealed areas where pore‐filling calcite was preferentially dissolved. Longer‐term rock‐water reactions resulted in induced carbonate mineralization, as evidenced by calcite crystals observed in a sample reacted for 102 days. © 2024 Society of Chemical Industry and John Wiley & Sons, Ltd.

Energy & Fuels↗
DOE OSTI2024

Utilization of Ultrasonication as a Method of Reducing Organic and Inorganic Contamination in Post‐Consumer Plastic Film Waste

Post-consumer plastic film waste often carries organic and inorganic contaminants that challenge recycling processes and affect the quality of recycled products. An effective contaminant removal procedure through washing such single-used plastic films (SUPFs) can address environmental and waste management concerns. This study compares the efficiency of different washing techniques in reducing SUPF contamination. To evaluate the efficacy of each washing technique, film samples collected from material recovery facilities are individually exposed to friction, ultrasonic-assisted, and a combination of both washes. Thermal analysis indicates that the polymers' melting temperature, crystallization temperature, and crystallinity remain unaffected by the washing methods, demonstrating method aptness. Confocal laser scanning microscope images show that washing results in a cleaner sample surface. 91% ash reduction during the combined wash treatment indicates a high method efficiency compared to the individual friction and ultrasonic wash procedures. This is further validated by reducing characteristic contaminant IR bands (3600–3000, 1750–1600, and 1100–1000 cm −1 ). Elements of concern such as Cd, Cr, Hg, and Pb in SUPFs after each washing technique applied conform with regulations (<100 ppm) for packaging products. This research shows the novel ultrasonic washing reduces more contamination than friction with shorter wash times and no surfactants.

42 ENGINEERING↗