Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal cycles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Parametric Design Study of a Power Electronics Package for Improving Solder Joint Reliability

The lifetime of a power electronics package is, to a large extent, determined by the reliability of its bonded interfaces under major loading conditions in an operational environment. Based on the application-level requirements of the package, bonded interface material is selected based on the results obtained from accelerated tests such as thermal cycling and power cycling. In addition to evaluating the reliability through accelerated tests, it is important to consider the impact of other component layers on the thermomechanical performance of the interface material, both from a material and geometric perspective. The co-efficient of thermal expansion (CTE) mismatch introduced by the use of different materials within a package and its structural design plays a critical role in determining the interface material reliability. In this paper, we present the results of a parametric modeling study of a power electronics package under thermal cycling in which the materials and geometric design of the different component layers were varied with respect to a baseline design to understand their impact on the reliability of the interface material. We chose the volume-averaged strain energy density per cycle computed at the corner region of the interface material as the metric for the reliability comparisons. Our results indicate that in addition to the CTE mismatch, the stiffness of individual component layers has a major impact on reliability. Among the different baseplates that we studied, aluminum silicon-carbide baseplates offered superior reliability over their copper and aluminum counterparts. We also found that the magnitude of the impact of stiffness variation—amongst the adjacent layers—on the reliability of the solder joint is dependent on the inherent CTE mismatch between the layers.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Parametric Design Study of a Power Electronics Package

The lifetime of a power electronics package is, to a large extent, determined by the reliability of its bonded interfaces under major loading conditions in an operational environment. Based on the application-level requirements of the package, bonded interface material is selected based on the results obtained from accelerated tests such as thermal cycling and power cycling. In addition to evaluating the reliability through accelerated tests, it is important to consider the impact of other component layers on the thermomechanical performance of the interface material, both from a material and geometric perspective. The co-efficient of thermal expansion (CTE) mismatch introduced by the use of different materials within a package and its structural design plays a critical role in determining the interface material reliability. In this paper, we present the results of a parametric modeling study of a power electronics package under thermal cycling in which the materials and geometric design of the different component layers were varied with respect to a baseline design to understand their impact on the reliability of the interface material. We chose the volume-averaged strain energy density per cycle computed at the corner region of the interface material as the metric for the reliability comparisons. Our results indicate that in addition to the CTE mismatch, the stiffness of individual component layers has a major impact on reliability. Among the different baseplates that we studied, aluminum silicon-carbide baseplates offered superior reliability over their copper and aluminum counterparts. We also found that the magnitude of the impact of stiffness variation—amongst the adjacent layers—on the reliability of the solder joint is dependent on the inherent CTE mismatch between the layers.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Hardness Prediction by Incorporating Heat Transfer and Molten Pool Fluid Flow in a Multi-pass, Multi-layer Weld for Onsite Repair of Grade 91 steel

Introduction: In the current fleet of fossil-fired power plants, creep strength enhanced ferritic steels (CSEF) are used to sustain the harsh service conditions. Enhanced properties of Grade 91 steel result from tempered martensite with a fine distribution of MX and M23C6 carbides. Grade 91 steel is subjected to onsite welding repair to remedy their degradation due to extreme service condition. Knowledge of weld repairability of these steels, such as as-welded hardness distribution, is essential to establishing sound repair procedures. Experimental trial and error tests can consume a lot of time as many welding variables need to be studied. For numerical modelling, most of the multi-pass multi-layer models are based on finite element method, which are limited to solve the heat conduction equation and ignore convective heat transfer due to melt flow. Moreover, the mesh has to be pre-built based on a known or assumed weld cross-section geometry. These finite element based models thus have limited predictive capability as defects are not considered and nugget size are pre-assumed. This research aims at developing a thermal and microstructure evolution model incorporating molten pool dynamics in a multi-pass multi-layer material deposition to predict the as-welded hardness distribution. Technical Approach: All the thermal, physical, and metallurgical properties of Grade 91 as a function of temperature are collected from the literature and inputted into the thermo-fluid model based on Flow-3D, a computational fluid dynamics software. A multi-pass, multi-layer material deposition is simulated where the melting of filler wire into the molten pool is directly considered based on the volume of fluid (VOF) method. The flow behaviour of the molten pool is used to understand the formation of deposition geometry and defects. The temperature profiles during the multi-pass, multi-layer welding are calculated. The results computed using the new model are compared against the experimental data of fusion zone geometry and thermal cycles. Hardness prediction in the heat-affected zone (HAZ) are made using Johnson-Mehl-Avrami (JMA) equation for solid-state phase transformation kinetics. The JMA parameters are extracted from the experimental data available in the literature. For comparison, a standard finite element heat conduction model is also developed to predict the thermal cycles and hardness distribution in the multi-pass, multi-layer weld. Expected Result: Results obtained using the molten pool dynamic simulation versus the finite element heat conduction model are compared. Specifically, the effects of convective heat transfer on the accuracy of the calculated thermal history, bead shape and size, and HAZ hardness distribution are examined.

Modeling, Grade 91 steel, Multi-pass multi-layer d↗
DOE OSTI2022

Multiscale investigation of the microstructural mechanisms driving ratchet growth in PBX 9502

The high explosive PBX 9502 undergoes irreversible expansion during thermal cycling (“ratchet growth”). Recent innovations in thermomechanical modeling via homogenization strategies are beginning to incorporate mesoscale information such as grain size, total porosity, and spatial distribution of voids and cracks. To generate a complete experimental data set to challenge and inform these models, PBX 9502 pellets were thermally cycled, cross-sectioned using ion polishing, and imaged in high resolution with scanning electron microscopy. Ratchet growth was found to drive expansion through microcracking. Microcracks were affected by agglomeration of crystals within the PBX. Virgin material showed greater ratchet growth than recycled material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Role of Oxidation Resistance in High Temperature Alloy Selection for a Future with Green Hydrogen

Hydrogen is being considered integral to the future energy landscape but there is limited mechanistic understanding and a lack of predictive models to describe the combined effects of alloy and gas composition, temperature, thermal cycling and water vapor contents on the oxidation behavior of high-temperature materials. Experimental evaluations were combined with coupled thermodynamic-kinetic modeling to investigate the oxidation behavior of five representative Ni-based superalloys in two water vapor contents (10%, 60% H 2 O) under thermal cycling (1-h, 100-h cyles) conditions at 800°C and 1000°C. The alloy with the highest Ti content demonstrated the poorest cyclic oxidation behavior while the alloy with highest Cr and Al contents was expected to continue to support protective formation of a compact Al 2 O 3 scale. Finally, accelerated degradation of the chromia-forming alloys was observed in the higher water vapor content but the impact on transient oxidation of the alumina-forming alloys needs further investigations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigation of Failure Modes, Mechanisms and Driving Forces for Electrically Conductive Adhesives as Interconnects in PV Modules

In this work we describe our current progress into investigating the reliability of ECA interconnects for PV modules. Preliminary thermal cycling experiments demonstrated that both cohesive and adhesive failure of the ECA joint are relevant failure modes that result in an increase of the joints electrical resistance. A thorough viscoelastic characterization of the candidate ECA was conducted to enable accurate numerical modeling of the joint’s response to thermal cycling. Combined with critical and subcritical fracture measurements, the numerical model elucidates that an additional fatigue mechanism exists which can result in fracture well below subcritical debonding threshold values. It is also demonstrated that fracture of the ECA is more sensitive to humidity than temperature and subcritical debonding mechanisms do exist which are again more sensitive to humidity.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2023

Advanced Drying Cycle Simulator Thermal Response to Commercial Drying Conditions

The purpose of this report is to document updates on testing of the apparatus built to simulate commercial drying procedures for spent nuclear fuel at the Nuclear Energy Work Complex at Sandia National Laboratories. Validation of the extent of water removal in a dry spent nuclear fuel storage system based on drying procedures used at nuclear power plants is needed to close existing technical gaps. Operational conditions leading to incomplete drying may have potential impacts on the fuel, cladding, and other components in the system during subsequent storage and disposal. A general lack of data suitable for model validation of commercial nuclear canister drying processes necessitates well-designed investigations of drying process efficacy and water retention that incorporate relevant physics and well-controlled boundary conditions. This report documents testing updates for the Advanced Drying Cycle Simulator (ADCS). This apparatus was built to simulate commercial drying procedures and quantify the amount of residual water remaining in a pressurized water reactor (PWR) fuel assembly after drying. The ADCS was constructed with a prototypic 17×17 PWR fuel skeleton and waterproof heater rods to simulate decay heat. These waterproof heaters are the next generation design to heater rods developed and tested at Sandia National Laboratories in FY20. This report describes preliminary testing of the ADCS through measurement and analysis of the thermal response of the system to a subset of commercial drying conditions that exclude the introduction of water, namely simulated decay heats and pressures relevant to commercial drying. This test series, referred to as a “dry” test series in this report, spans three uniform waterproof heater rod powers (representing spent fuel decay heats), four helium fill pressures, and six vacuum levels. This test series was conducted to cover the range of expected ADCS testing conditions for upcoming “wet” testing, where water will be introduced and a simulated commercial drying cycle will be performed. The dry test conditions were derived from the commercial drying conditions seen in the High Burnup Demonstration and the vacuum drying conditions chosen for a smaller scale Dashpot Drying Apparatus tested at Sandia National Laboratories in FY22. For a given uniform power and pressure/vacuum level, the ADCS was operated at constant power and pressure and allowed to reach steady state conditions. The thermal data obtained from these tests were analyzed, and the results can inform computational models built to simulate commercial drying processes by providing baseline thermal data prior to the introduction of water. Following the preliminary dry tests, a test plan for the ADCS will be developed to implement a drying procedure that begins with the introduction of water to the system and is based on measurements from the drying process used for the High Burnup Demonstration Project. While applying power to the simulated fuel rods, this procedure is expected to consist of filling the ADCS vessel with water, draining the water with applied pressure and multiple helium blowdowns, evacuating additional water with a vacuum drying sequence at successively lower pressures, and backfilling the vessel with helium. Additional investigations are expected to feature failed fuel rod simulators with engineered cladding defects and guide tubes with obstructed dashpots to challenge the drying system with multiple water retention sites. The data from these investigations is expected to inform the efficacy of commercial drying operations through the quantification of residual water in a prototypic-length dry storage canister.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Effect of Initial Microstructure on the Toughness of Coarse-Grained Heat-Affected Zone in a Microalloyed Steel

Toughness of the coarse-grained-heat-affected-zone (CGHAZ) strongly depends on the prior austenite grain size. The prior austenite grain size is affected not only by chemical composition, thermal cycle, and dissolution of second-phase particles, but also by the initial microstructure. The effect of base metal microstructure (ferrite/pearlite obtained by air cooling and martensite obtained by water-quenching) on Charpy impact toughness of the CGHAZ has been investigated for different heat inputs for high-heat input welding of a microalloyed steel. A welding thermal cycle with a heat input of 100 kJ/cm and 400 kJ/cm were simulated on the MMS-300 system. Despite a similar microstructure in the CGHAZ of both the base metals, the average Charpy impact energy for the air-cooled base metal was found to be higher than the water-quenched base metal. Through thermo-kinetic simulations, it was found that a higher enrichment of Mn/C at the ferrite/austenite transformation interface of the CGHAZ of water-quenched base metal resulted in stabilizing austenite at a lower A1 temperature, which resulted in a coarser austenite grain size and eventually lowering the toughness of the CGHAZ.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Differences in the response of two light guide technologies and two readout technologies after an exchange of liquid argon in the dewar

In this investigation the response to the scintillation light generated by through-going cosmic muons in liquid argon (LAr) was measured by two light guide technologies and two readout technologies after five weeks of running in the TallBo dewar at Fermilab. The response was remeasured after the dewar was drained of LAr, refilled, and then run again for an additional four weeks. After the dewar was refilled, there was clear evidence that the scintillation signal had dropped significantly. The two light guide technologies were developed at Indiana University and MIT/Fermilab. The two readout technologies were boards that passively or actively ganged 12 Hamamatsu MPPCs. Two possible explanations were identified for the degraded signal: the response of the two light guide technologies degraded due to damage caused by thermal cycling, and/or unknown differences in the trace residual Xe contamination in the fills of LAr led to the observed drop in scintillation light. Neither absorption nor quenching by N 2 , O 2 , and H 2 O contamination can account for the degradation. Neither the individual Hamamatsu MPPCs nor the passive/active ganging boards appear to have been affected by the thermal cycling. The path length distributions of the cosmics traversing the dewar appear quite similar in both event samples.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Enabling Recycling of Composites: Understanding the Impacts of Multiple Thermal Processing Cycles

When considering the utilization of recycled short carbon fiber feedstock materials for advanced manufacturing, understanding the material degradation behavior is essential in determining how many times a composite material can be effectively reprocessed and remanufactured. This study characterizes the degradation behavior of short carbon fiber acrylonitrile butadiene (CF-ABS) that has been reprocessed five times with twin screw extrusion. Parallel plate rheology was completed to observe the degradation in complex viscosity of the recycled feedstock materials. Gel permeation chromatography (GPC) was utilized to characterize the changes in molecular weight distribution of the recycled materials as a result of thermal and mechanical degradation during the re-processing steps. Rheological characterization, GPC, and twin-screw processing data help inform the process optimizations required to process the recycled feedstock material. Successful characterization of the degradation behavior of short fiber composite feedstock materials aids in increased understanding of the lifespan of high value carbon fiber composite materials and aids in process optimization of recycled composite materials.

Walker, Roo↗
DOE OSTI2021

Microstructure and mechanical properties of high Mn-containing ferritic-martensitic alloys exposed to cyclical thermal treatment

Substantial residual tensile stress tends to accumulate in currently available high-Cr ferritic martensitic steels that are subjected to cyclical heat treatment, which leads to premature brittle fracture. By tailoring the alloy composition, this thermal cycling can be exploited to induce a high number density of nanoprecipitates and phase transformations countering residual tensile stresses. In this work, three new variants of ferritic-martensitic steels have been designed with computational thermodynamics to meet the goals of mitigating residual tensile stresses by lowering martensite start temperatures and of enhancing mechanical strength and irradiation sink strength by increasing the number density of nanoprecipitates. Furthermore, ctenast materials were subjected to cyclical heat treatment. The thermally cycled samples were evaluated with mechanical testing and microstructural analysis to identify the optimal composition in which figures of merit include low residual stress and a high density of nanoscale MX (M = metal, X = C/N) precipitates, leading to high yield strength with reasonable ductility. The noticeably higher density of nanoprecipitates in the optimal alloy favor its higher yield strength, which is supported by the microstructure-derived yield strength calculation and precipitation kinetics simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Comparison of Designs of Hydrogen Isotope Separation Columns by Numerical Modeling

Mixtures of gas-phase hydrogen isotopologues (diatomic combinations of protium, deuterium, and tritium) can be separated using columns containing a solid such as palladium that reversibly absorbs hydrogen. A temperature-swing process can transport hydrogen into or out of a column by inducing temperature-dependent absorption or desorption reactions. Here, we consider two designs: a thermal cycling absorption process, which moves hydrogen back and forth between two columns, and a simulated moving bed (SMB), where columns are in a circular arrangement. We present a numerical mass and heat transport model of absorption columns for hydrogen isotope separation. It includes a detailed treatment of the absorption–desorption reaction for palladium. By comparing the isotope concentrations within the columns as a function of position and time, we observe that SMB can lead to sharper separations for a given number of thermal cycles by avoiding the remixing of isotopes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Clarifying the formation of equiaxed grains and microstructural refinement in the additive manufacturing of Ti-Cu

Controlling microstructural evolution in metallic additive manufacturing (AM) is difficult, especially in producing refined as-built grains instead of coarse, directional grains. Traditional solutions involve adding inoculants to AM feedstocks, but titanium (Ti) alloys cannot employ this approach without producing detrimental secondary phases. Ti-Cu (Ti-copper) alloys offer a solution through constitutional supercooling and/or solid state thermal cycling under AM conditions. This work analyzes a compositionally graded directed energy deposition (DED) Ti-Cu build, single-melt laser tracks, and dilatometric heat treatments to evaluate if, when, and by what mechanism(s) microstructural refinement occurs. Refinement by inoculation of unmelted powder particles was also considered. Constitutional supercooling produced no net microstructural refinement as any equiaxed dendrites which form are remelted with new deposition. This finding agreed with solidification modeling of powder bed fusion-laser beam (PBF-LB) and DED builds. Solid state thermal cycling refined microstructures only during ex-situ dilatometric heat treatments, suggesting build parameter optimization is needed to achieve refinement in-situ. Accidental heterogeneous nucleation on unmelted Ti powder, originating from the different thermophysical properties of Ti and Cu, provided the most significant microstructural refinement. This work systematically assesses the microstructural refinement mechanisms of Ti-Cu in AM builds and offers insights into microstructural control in eutectoid alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Metal-supported solid oxide fuel cells operating with reformed natural gas and sulfur

The performance, long-term durability, and thermal cycling tolerance of metal supported solid oxide fuel cells (MS-SOFCs) operating with natural gas reformate fuels is assessed. Symmetric MS-SOFCs with composite SDC-Ni anode catalysts and PrO x cathode catalysts are operated with simulated natural gas steam-reformate and partial-oxidation-reformate fuels with 1 ppm and 5 ppm of sulfur. Cells are operated for 1000 h with initial degradation rates similar to humidified H 2 , and initial performance differences attributed to the lower H 2 concentration in reformate fuels. Additionally, cells tolerate many aggressive thermal cycles with sulfur present, with minimal impact on performance. Post mortem analysis suggests that Ni particle coarsening and Cr deposition are sources of degradation, while carbon and sulfur deposition are not observed. Overall, MS-SOFCs operate successfully with reformed natural gas.

08 HYDROGEN↗
DOE OSTI2025

Wood template-supported phase change material composites for durable and form-stable thermal energy storage in buildings

Here, to reduce and shift peak energy loads in buildings, phase change materials (PCMs) with high transition enthalpies and transition temperatures near human thermal comfort are desirable for thermal energy storage (TES). Traditional solid/liquid PCMs suffer from leakage during thermal cycling, requiring encapsulation that lowers heat storage capacity. Wood templates (WTs), with porous and hierarchical structures, provide natural encapsulation scaffolds for PCM containment. Polyethylene glycol (PEG) is a compatible PCM with WTs, but when infiltrated alone, ~30 wt% of PEG binds to wood with no detectable phase change, limiting TES efficiency. To address this, we developed a method to (1) improve the form stability of balsa and pine-based composites (BWT + PCMs and PWT + PCMs) and (2) reduce inactive PCM within the composites to ~10 wt%. BWT + PCMs exhibit transition properties upwards of 114.2 J/g at 25.4 degrees C, with no degradation after 1000 thermal cycles, and similar stiffness compared to raw balsa. Meanwhile, PWT + PCMs exhibit 25 % higher storage efficiency with the addition of poly(ethylene glycol) diacrylate compared to solely PEG-infiltrated PWT. PWT + PCM retains 84 % of raw pine's mechanical stiffness, sufficient for light-duty construction. Our shape-stabilized WT + PCM composites enrich the functionality of wood materials as both ideal TES material candidates and light-duty building construction applications.

25 ENERGY STORAGE↗
DOE OSTI2020

Standard Characterization Techniques for Inorganic Phase Change Materials

Salt hydrates are promising candidates for phase change materials (PCMs) because of their low cost and high energy storage capacity. However, practical applications of salt hydrate based PCMs are limited due to their poor thermal cycling performance caused by phase separation and supercooling. Various techniques, including differential scanning calorimetry (DSC) and transient plane source (TPS) have been used to characterize salt hydrate based PCMs but may not provide full understanding of the degradation mechanism. In this manuscript, salt hydrate and graphite composites are prepared. Temperature history (T-History) method and X-ray diffraction (XRD) are utilized for measuring melting temperature, energy storage, and latent heat degradation of the PCM composites. Highlighting the importance of each technique and how each technique plays an important role in analyzing salt hydrates performance accurately. Temperature history, and X-ray diffraction are also used in conjunction to precisely predict the cause of degradation in salt hydrate PCMs with thermal cycling, as in most literatures the cause of degradation in salt hydrate are attributed to phase segregation, supercooling, and change in stichometry water concentration without any scientific validation.

Kumar, Navin↗
DOE OSTI2022

Extended Accelerated Stress Testing (EAST) of Glass/Glass, Glass/Backsheet and Glass/Transparent Backsheet PV Modules: Influence of EVA and POE Encapsulants: Preprint

This paper presents the indoor extended accelerated stress testing (EAST) results of glass/glass (GG), glass/backsheet (GB) and glass/transparent backsheet (GT) modules having identical cells and two different encapsulant types, ethyl-vinyl-acetate (EVA) and polyolefin-elastomer (POE). Six 4-cell modules having the above-mentioned construction combinations were subjected to extended ultraviolet (UV; 600 kWh/m2), damp-heat (DH; 2000 hours) and thermal-cycling (TC; 600 cycles) tests. The post-stress UV fluorescent imaging, electroluminescent imaging, reflectance spectrophotometry and colorimetry results indicated that the grid finger degradation and encapsulant browning are slightly higher in the GG modules compared to the GB modules. The post-stress IV test results indicated, in general, that the GG/EVA modules tend to perform inferior to the GG/POE modules with the EAST evaluation.

EVA↗
DOE OSTI2022

High Performance Circuit Pastes for Solid Oxide Fuel Cell Applications: Final Technical Report

Using a combination of in-plane electrical conductivity measurements, electrical contact resistance measurements, tensile fracture tests, double shear lap fracture tests, rapid thermal cycling adhesion tests, in situ wetting angle measurements, 3D X-ray tomography, reduction-oxidation (RedOx) cycling, scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDAX), Density Functional Theory (DFT) modeling, Molecular Dynamics (MD) modeling, and Phase Field modeling, this project determined that a new brazing technique developed by the PIs (specifically the use of nickel particles to direct the wetting and spreading of molten silver) could be used to produce well-adhered, >97% dense, electrically-conductive circuits, current collectors, and/or electrical contacts on a variety of ceramic and ceramic-coated substrates (specifically lanthanum strontium manganite, yttria stabilized zirconia, sapphire, Cr2O3-passivated stainless steel, and Al2O3-passivated stainless steel). Compared to other silver-based alternatives, Ag:Ni led to less manufacturing defects and was more tolerant of the extreme environments (isothermal high-temperature aging) and occasional abuse (rapid thermal cycling and RedOx cycling) encountered during Solid Oxide Fuel Cell and/or Solid Oxide Electrolysis Cell operation. Further, in some situations (such as when to produce Ag:Ni electrical contacts to Al2O3-protected stainless steel) the Ni particles also improved operation by acting as chemical getters that removed electrically-insulating, surface-segregating substrate impurities (i.e. by lowering the contact resistance with the underlying substrate).

36 MATERIALS SCIENCE↗