Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

A lower bound to the thermal diffusivity of insulators

It has been known for decades that thermal conductivity of insulating crystals becomes proportional to the inverse of temperature when the latter is comparable to, or higher than, the Debye temperature. This behavior has been understood as resulting from Umklapp scattering among phonons. We put under scrutiny the magnitude of the thermal diffusion constant in this regime and find that it does not fall below a threshold set by the square of sound velocity times the Planckian time (τ p = h / k B T ). The conclusion, based on scrutinizing the ratio in cubic crystals with high thermal resistivity, appears to hold even in glasses where Umklapp events are not conceivable. Furthermore, explaining this boundary, reminiscent of a recently-noticed limit for charge transport in metals, is a challenge to theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Determination of heat conductivity and thermal diffusivity of waste glass melter feed: Extension to high temperatures

The heat conductivity ({lambda}) and the thermal diffusivity (a) of reacting glass batch, or melter feed, control the heat flux into and within the cold cap, a layer of reacting material floating on the pool of molten glass in an all-electric continuous waste glass melter. After previously estimating {lambda} of melter feed at temperatures up to 680 deg C, we focus in this work on the {lambda}(T) function at T > 680 deg C, at which the feed material becomes foamy. We used a customized experimental setup consisting of a large cylindrical crucible with an assembly of thermocouples, which monitored the evolution of the temperature field while the crucible with feed was heated at a constant rate from room temperature up to 1100°C. Approximating measured temperature profiles by polynomial functions, we used the heat transfer equation to estimate the {lambda}(T) approximation function, which we subsequently optimized using the finite-volume method combined with least-squares analysis. The heat conductivity increased as the temperature increased until the feed began to expand into foam, at which point the conductivity dropped. It began to increase again as the foam turned into a bubble-free glass melt. We discuss the implications of this behavior for the mathematical modeling of the cold cap.

36 MATERIALS SCIENCE↗

A technique to measure the thermal diffusivity of high Tc superconductors

High T(sub c) superconducting electrical current leads and ground straps will be used in cryogenic coolers in future NASA Goddard Space Flight Center missions. These superconducting samples are long, thin leads with a typical diameter of two millimeters. A longitudinal method is developed to measure the thermal diffusivity of candidate materials for this application. This technique uses a peltier junction to supply an oscillatory heat wave into one end of a sample and will use low mass thermocouples to follow the heat wave along the sample. The thermal diffusivity is calculated using both the exponential decay of the heat wave and the phase shift to the wave. Measurements are performed in a cryostat between 10 K and room temperature.

Powers, Charles E.↗

A technique to measure the thermal diffusivity of high T(sub c) superconductors

High T(sub c) superconducting electrical current leads and ground straps will be used in cryogenic coolers in future NASA Goddard Space Flight Center missions. These superconducting samples will be long, thin leads with a typical diameter of two millimeters. A longitudinal method is being developed to measure the thermal diffusivity of candidate materials for this application. This technique will use a peltier junction to supply an oscillatory heat wave into one end of a sample and will use low mass thermocouples to follow the heat wave along the sample. The thermal diffusivity will be calculated using both the exponential decay of the heat wave and the phase shift of the wave. Measurements will be done in a cryostat between 10 K and room temperature.

Powers, Charles E.↗

Diffusion-controlled alloying of single-phase multi-principal transition metal carbides with high toughness and low thermal diffusivity

Multicomponent alloying has displayed extraordinary potential for producing exceptional structural and functional materials. Consequently, the synthesis of single-phase, multi-principal covalent compounds remains a challenge. Here, we present a diffusion-controlled alloying strategy for the realization of covalent multi-principal transition metal carbides (MPTMCs) with a single face-centered cubic phase. The increased interfacial diffusion promoted by the addition of a nonstoichiometric compound leads to rapid formation of the single phase at much lower sintering temperature. Direct atomic-level observations via scanning transmission electron microscopy demonstrate that MPTMCs are composed of a single phase with a random distribution of all cations, which holds the key to the unique combinations of improved fracture toughness, superior Vickers hardness, and extremely lower thermal diffusivity achieved in MPTMCs. Conclusively, the present discovery provides a promising approach toward the design and synthesis of next-generation high-performance materials.

36 MATERIALS SCIENCE↗

Non-Contact Measurement of Thermal Diffusivity in Ion-Implanted Nuclear Materials

Knowledge of mechanical and physical property evolution due to irradiation damage is essential for the development of future fission and fusion reactors. Ion-irradiation provides an excellent proxy for studying irradiation damage, allowing high damage doses without sample activation. Limited ion-penetration-depth means that only few-micron-thick damaged layers are produced. Substantial effort has been devoted to probing the mechanical properties of these thin implanted layers. Yet, whilst key to reactor design, their thermal transport properties remain largely unexplored due to a lack of suitable measurement techniques. Here we demonstrate non-contact thermal diffusivity measurements in ion-implanted tungsten for nuclear fusion armour. Alloying with transmutation elements and the interaction of retained gas with implantation-induced defects both lead to dramatic reductions in thermal diffusivity. These changes are well captured by our modelling approaches. Our observations have important implications for the design of future fusion power plants.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Thermal diffusivity and chaos in metals without quasiparticles

We study here the thermal diffusivity D T in models of metals without quasiparticle excitations (“strange metals”). The many-body quantum chaos and transport properties of such metals can be efficiently described by a holographic representation in a gravitational theory in an emergent curved spacetime with an additional spatial dimension. We find that at generic infrared fixed points D T is always related to parameters characterizing many-body quantum chaos: the butterfly velocity v B and Lyapunov time τ L through D T ~ v B 2 τ L . The relationship holds independently of the charge density, periodic potential strength, or magnetic field at the fixed point. The generality of this result follows from the observation that the thermal conductivity of strange metals depends only on the metric near the horizon of a black hole in the emergent spacetime and is otherwise insensitive to the profile of any matter fields.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Quantitative thermal diffusivity measurements of composites

A remote radiometric technique for making quantitative thermal diffusivity measurements is described. The technique was designed to make assessments of the structural integrity of large composite parts, such as wings, and can be performed at field sites. In the measurement technique, a CO2 laser beam is scanned using two orthogonal servo-controlled deflecting mirrors. An infrared imager, whose scanning mirrors oscillate in the vertical and the horizontal directions, is used as the detector. The analysis technique used to extract the diffusivity from these images is based on a thin infinite plate assumption, which requires waiting a given period of time for the temperature to equilibrate throughout the thickness of the sample. The technique is shown to be accurate to within two percent for values of the order of those for composite diffusivities, and to be insensitive to convection losses.

Heath, D. M.↗

A detailed study of the photo-injection annealing of thermally diffused InP solar cells

A detailed analysis of the annealing of thermally diffused InP solar cells fabricated by the Nippon Mining Co. is presented. The cells were irradiated with 1 MeV electrons, and the induced degradation is measured using deep level transient spectroscopy and low temperature (86 K) IV measurements. Clear recovery of the photovoltaic parameters is observed during low temperature (T is less than 300 K) solar illuminations (1 sun, AMO) with further recovery at higher temperatures (300 less than T less than 500 K). For example, the output of a cell which was irradiated up to a fluence of 1 x 10(exp 16) cm(sup -2) was observed to recover to within 5 percent of the pre-irradiation output. An apparent correlation between the recovery of I(sub sc) and the annealing of the H4 defect and of the minority carrier trapping centers is observed. An apparent correlation between the recovery of VO, and the annealing of the H5 defect is also observed. These apparent correlations are used to develop a possible model for the mechanism of the recovery of the solar cells.

Walters, R. J.↗

Measured thermal diffusivity of Hg(1-x)Cd(x)Te solids and melts

The thermal diffusivity of Hg(1-x)Cd(x)Te melts is found to rise rapidly with temperature to values characteristic of metals. Solid and melt diffusivities for values of x from 0 to 0.3 and over a temperature range from 150 to 900 C have been determined by the laser flash method of Parker, Taylor, and Cowan. The diffusivity decreases from a maximum at x = 0 in both the solid and the liquid, with the values observed at x = 0.3 being about 40 percent of those for x = 0. The solid diffusivity for x = 0 is 1.7 sq mm/s at 150 C, decreasing to 0.7 sq mm/s at the melting point. The x = 0 liquid diffusivity increases from 0.7 sq mm/s at the melting point to 3.5 sq mm/s at 900 C.

Holland, L. R.↗

Apparatus for determining a thermal conductivity and a thermal diffusivity of a material, and related methods

A method of determining a thermal conductivity and a thermal diffusivity of a material comprises exposing a specimen comprising a substrate of a material and a metallic film over the substrate to an amplitude modulated pump laser beam comprising electromagnetic radiation having a first wavelength and a first modulation frequency to form a pump spot on the metallic film. The specimen is exposed to a probe laser beam comprising electromagnetic radiation having a second wavelength to form a probe spot on the metallic film. A phase shift between the pump laser beam and a reflected probe laser beam is measured while scanning the pump spot relative to the probe spot. A modulation frequency of the pump laser beam is changed to a second modulation frequency and the pump spot is scanned relative to the probe spot while detecting the phase shift. A phase profile of the material is measured and a continuum-based model is fit to the phase profile. Related microscopes and related methods are also disclosed.

36 MATERIALS SCIENCE↗

AlCu alloy films prepared by the thermal diffusion technique

100-nm thick films of Al{sub 1-x}Cu{sub x} alloys were prepared on glass substrates by thermal diffusion technique. The Cu atomic concentration was varied from 10% to 90%. Alloys were prepared at different temperatures into a vacuum oven with Argon atmosphere. Two thermal processes were used: i) heating the film at 400 deg. C in a single step, and ii) heating the films in sequential steps at 100, 200, 300 and 400 deg. C. Morphology, electrical resistivity, and crystalline orientation of the alloys were studied. The electrical resistivity and surface roughness of the alloys were found to depend strongly on the atomic composition and the diffusion temperature. However, we did not find differences between samples prepared under the two thermal processes. Alloys prepared with x = 0.6 and x = 0.1-0.3 as Cu at concentration exhibited values on electrical resistivity and surface roughness lower than pure Al. Different phases of the Al{sub 1} {sub -} {sub x}Cu{sub x} films were observed as a function of Cu concentration showing a good agreement with the AlCu phase diagram.

36 MATERIALS SCIENCE↗

Venus ionosphere - Photochemical and thermal diffusion control of ion composition

The major photochemical sources and sinks for ten of the ions measured by the ion mass spectrometer on the Pioneer Venus bus and orbiter spacecraft that are consistent with the neutral gas composition measured on the same spacecraft are identified. The neutral gas temperature (as a function of solar zenith angle) derived from measured ion distributions in photochemical equilibrium is given. Above 200 kilometers, the altitude behavior of ions is generally controlled by plasma diffusion, with important modifications for minor ions due to thermal diffusion resulting from the observed gradients of plasma temperatures. The dayside equilibrium distributions of ions are sometimes perturbed by plasma convection, while lateral transport of ions from the dayside seems to be a major source of the nightside ionosphere.

Bauer, S. J.↗

Thermal Diffusivity and Conductivity of Hg(1-x)Zn(x)Te Solids and Melts

The thermal diffusivity of pseudobinary Hg(1-x)Zn(x)Te solids and melts was measured by the laser flash method. The measured diffusivities for the solids of 0.10 less than or equal to x less than or equal to 0.30 are about 60% of that of the HgTe solid. Those for the melts rise rapidly with temperature but less so with increasing x. For x = 0.30, the diffusivity of the melt is about one third of that of the HgTe melt. Using the calculated beat capacity data from the associated solution model and measured density values, the thermal conductivity for the pseudobinary Hg(1-x)Zn(x)Te solids of 0.10 less than or equal to x less than or equal to 0.30 and for the melts of x = O.10, 0.16, and 0.30 was determined.

Sha, Yi-Gao↗

Insights into thermal diffusion of germanium and oxygen atoms in HfO{sub 2}/GeO{sub 2}/Ge gate stacks and their suppressed reaction with atomically thin AlO{sub x} interlayers

The thermal diffusion of germanium and oxygen atoms in HfO{sub 2}/GeO{sub 2}/Ge gate stacks was comprehensively evaluated by x-ray photoelectron spectroscopy and secondary ion mass spectrometry combined with an isotopic labeling technique. It was found that {sup 18}O-tracers composing the GeO{sub 2} underlayers diffuse within the HfO{sub 2} overlayers based on Fick's law with the low activation energy of about 0.5 eV. Although out-diffusion of the germanium atoms through HfO{sub 2} also proceeded at the low temperatures of around 200 °C, the diffusing germanium atoms preferentially segregated on the HfO{sub 2} surfaces, and the reaction was further enhanced at high temperatures with the assistance of GeO desorption. A technique to insert atomically thin AlO{sub x} interlayers between the HfO{sub 2} and GeO{sub 2} layers was proven to effectively suppress both of these independent germanium and oxygen intermixing reactions in the gate stacks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Remarks on the thesis of Aitor Bengoechea Fernández: Generalization of Doppler effect processing using S(α,β) thermal diffusion laws

The thesis titled “Generalization of Doppler effect processing using S(α,β) thermal diffusion laws” addresses a critical gap in the modeling of neutron scattering phenomena in nuclear materials, particularly where crystal lattice effects intersect with low-energy resonances. Conducted within the Doctoral School ED 352 at Aix-Marseille Université and hosted at CEA Cadarache, the research presents a theoretical and numerical framework for extending the applicability of Thermal Scattering Laws (TSLs) using higher-order correlation functions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Ice crystal growth in a dynamic thermal diffusion chamber

Ice crystals were grown in a supersaturated environment produced by a dynamic thermal diffusion chamber, which employed two horizontal plates separated by a distance of 2.5 cm. Air was circulated between and along the 1.2 m length of the plates past ice crystals which nucleated and grew from a fiber suspended vertically between the two plates. A zoom stereo microscope with a magnification which ranged from 3X to 80X and both 35 mm still photographs and 16 mm time lapse cine films taken through the microscope were used to study the variation of the shape and linear growth rate of ice crystals as a function of the ambient temperature, the ambient supersaturation, and the forced ventilation velocity. The ambient growth conditions were varied over the range of temperature 0 to -40 C, over the range of supersaturation 4% to 50% with respect to ice, and over the range of forced ventilation velocities 0 cm/s to 20 cm/s.

Keller, V. W.↗