Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

From dynamics to kinetics for the dissociation of •QOOH radicals derived from isopentane

Thermal dissociation rates for hydroperoxyalkyl (•QOOH) radicals are challenging to measure due to their inherent instability. Recent dynamics experiments have demonstrated that in situ synthesis of •QOOH radicals in a supersonic expansion in combination with IR action spectroscopy provides an effective route to accurately map their energy-resolved dissociation rates. Collaborative theoretical analyses provide a route for converting from those microcanonical rates to accurate temperature- and pressure-dependent thermal rate constants. Here, we present the results of this conversion for the dissociation of two isopentyl β-QOOH isomers of relevance to isopentane oxidation. The results are compared with existing literature values, as well as with results obtained in a similar fashion for related •QOOH systems. Extrapolations from benchmark calculations of barrier properties for smaller systems to accurate predictions for larger systems and multidimensional hindered rotor treatments are both shown to be important components of the theoretical analysis. For completeness, we extend the theoretical analysis to a treatment of the full RO 2 /QOOH system for isopentyl (1,1-dimethyl-propyl) radical.

Ab initio kinetics↗
DOE OSTI2023

System efficiency of packed bed TES with radial flow vs. axial flow – Influence of aspect ratio

Here, this paper compares the net system efficiency, including thermal efficiency and pressure drop effects, of radial versus axial flow packed beds for thermal energy storage. The traditional packed bed system is a cylindrical geometry where fluid flows axially from one end to another. However, issues of thermal stratification and high-pressure drop have led to recent studies on radial flow systems. One potential benefit is the reduced pressure drop in a radial flow system. This paper compares the performance of radial flow and axial flow systems at a range of aspect ratios (AR = H/D bed ) from 0.21 to 1.92 using a numerical model where the storage volume is held constant in all cases. When the radial flow bed is at a low aspect ratio (short/wide), the thermal front is improved but the pressure drop is high. At a high aspect ratio, the velocity is reduced in radial flow, leading to decreased pressure drop but an increased spreads in the thermal front that lowers thermal efficiency. The opposite trends are noted in axial flow. Thermal efficiencies of 83–91 % were noted for radial flow, while they ranged from 85 to 94 % in axial flow. Net efficiencies including pressure drop ranged from 74 to 82 % for radial flow and 80–87 % for axial flow. In both systems, a peak net efficiency was noted between the highest and lowest aspect ratio. While some aspect ratios with radial flow outperform axial flow from a net efficiency perspective, the results show that the highest net efficiency from axial flow is higher than that from radial flow. Overall, this paper highlights the importance of innovative TES designs and their potential to improve energy efficiency.

25 ENERGY STORAGE↗
DOE OSTI2020

Vented and sealed cookoff of powdered and pressed ε-CL-20

In this work, we have completed a series of vented and sealed cookoff experiments of the ε-polymorph of CL-20 in our Sandia Instrumented Thermal Ignition (SITI) apparatus using both powder and pressed pellets at nominal densities of 313 ± 8 kg/m 3 and 1030 ± 4 kg/m 3 , respectively. The boundary temperature of our aluminum confinement cylinder was ramped in 10 minutes from room temperature to a prescribed set-point temperature ranging between 448 nd 468 K and held at the set-point temperature until ignition. A universal cookoff model (UCM) has been calibrated using the ε-CL-20 SITI data to predict pressurization and thermal ignition of ε-CL-20. The ignition model was validated by using one-dimensional time-to-explosion (ODTX) ignition data from a different laboratory. We found that a thirtyfold increase in the reaction rates due to liquefaction at 520 K could explain the high temperature ODTX cookoff data. The model gives a plausible explanation of why melting is important in fast cookoff events involving CL-20. Our model also gives support to 520 K as the liquefaction point of CL-20, which has different values in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Implementation and verification of a user-defined element (UEL) for coupled thermal-hydraulic-mechanical-chemical (THMC) processes in saturated geological media

Efficient and accurate modeling of the coupled thermal-hydraulic-mechanical-chemical (THMC) processes in various rock formations is indispensable for designing energy geo-structures such as underground repositories for high-level nuclear wastes. Here, this work focuses on developing and verifying an implicit finite element solver for generic coupled THMC problems in geological settings. Starting from the mass, momentum, and energy balance laws, a specialized set of governing equations and a thermoporoelastic constitutive model is derived. This system is then solved by an implicit finite element (FE) scheme. Specifically, the residuals and the Jacobians are scripted in a user-defined element (UEL) subroutine which is then combined with the general-purpose FE software Abaqus Standard to solve initial-boundary value problems. Considering the complexity of the system, the UEL development follows a stepwise manner by first solving the coupled hydraulic-mechanical (HM) and thermal-hydraulic-mechanical (THM) equations before moving on to the full THMC problem. Each implementation step consists of at least one verification test by comparing computed results with closed-form analytical solutions to ensure that the various coupling effects are correctly realized. To demonstrate the robustness of the algorithm and to validate the UEL, a three-dimensional case study is performed with reference to the in-situ heating test of ATLAS at Belgium in 1980s. A hypothetical radionuclide leakage event is then simulated by activating the chemical-concentration degree of freedom and prescribing a constant high concentration at the heater's surface. The model predicts a limited contaminated regime after six years considering both diffusion and advection effects on species transport.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Autonomous Aerosol and Plasma Co‐Jet Printing of Metallic Devices at Ambient Temperature

Abstract Additive manufacturing of metallic materials holds the potential to revolutionize the fabrication of functional devices unattainable via traditional methods. Despite recent advancements, printing metallic materials typically requires thermal processing at elevated temperatures to form dense structures with desired properties, which presents a major challenge for direct printing and integration with temperature‐sensitive materials. Herein, a unique co‐jet printing (CJP) method is reported integrating an aerosol jet and a non‐thermal, atmospheric pressure plasma jet to enable concurrent aerosol deposition of metal nanoparticle inks and in situ sintering at ambient temperature. A machine learning algorithm is integrated with the CJP to perform real‐time defect detection and autonomous correction, enhancing the yield of printed films with high electrical conductivity from 44% to 94%. Concurrent printing and sintering eliminate the need for post‐printing processing, reducing the overall manufacturing time by multiple folds depending on product size. CJP enables direct printing of functional devices on a variety of temperature‐sensitive materials including biological materials. Direct printing of hydration sensors on living plant leaves is demonstrated for long‐duration monitoring of hydration level in the plant. The versatile CJP method opens tremendous opportunities to harmoniously integrate abiotic and biotic materials for emerging applications in wearable/implantable devices and biohybrid systems.

Du, Yipu [Department of Aerospace and Mechanical E↗
DOE OSTI2020

Estimation of stress and stress-induced permeability change in a geological nuclear waste repository in a thermo-hydrologically coupled simulation

Geologic disposal is a promising solution for a safe permanent isolation of accumulated high-level nuclear waste from nuclear powerplants. The behavior of host rock is highly coupled thermally, hydromechanically, and chemically. Numerical simulations of such coupled phenomena for the extremely long term (>100,000 years) and large length scale (>1 km) of geologic disposal remain to be computationally challenging. In this study, a methodology has been developed to approximate stress and stress-induced permeability change in host rock using only thermo-hydrological (TH) variables. A coupled thermo-hydromechanical (THM) simulation is carried out using TOUGH-FLAC simulator to model THM behaviors of a generic nuclear waste repository, in order to evaluate the performance of the developed methodology, which is implemented in a coupled TH simulation. Results show that stress and permeability change estimated by the developed methodology in the TH-coupled simulation match those calculated in the THM-coupled simulation over the simulated timeframe of over 10,000 years. Details about errors in stress and permeability estimates accrued by the developed methodology are discussed here. The developed methodology will help incorporate stress-induced permeability change into existing TH simulators for the long-term radionuclide transport in geologic disposal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Lignin extraction and upgrading using deep eutectic solvents

Deep eutectic solvents (DESs) are a class of green solvents exhibiting low vapor pressure, high thermal stability,low toxicity, and biodegradability. These features make them attractive solvents for lignocellulosic biomassprocessing, especially for lignin valorization. DESs not only solubilize lignin from lignocellulose biomass, butalso confer extracted lignin with properties favorable to its further upgrading. This review summarizes recentadvances in biomass fractionation using DESs for lignin extraction. It also covers lignin upgrading in DESs interms of depolymerization and functionalization. The challenges of tailoring lignin properties by DESs for differentvalorization routes are also discussed.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Short Communication: Observation of Initial Burst Release of Fission Gas from High-Burnup UO 2 Nuclear Fuel During Thermal Transient

A system was developed and tested to provide a deeper understanding of the fission gas release kinetics from nuclear fuel during thermal transients. Pressure, temperature, spectral data, and optical images were simultaneously collected during resistive sample heating, and all released gases were collected in liquid nitrogen-cooled charcoal traps. Standup testing was performed with a high-burnup nuclear fuel segment from rod section with an average local burnup of 77 GWd/tU. During heating, the segment released approximately 6 ± 2% of generated fission gas inventory after ramp heating to 460°C. Here, heating ceased when the sample ejected from the holder, as observed by constant imaging.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Simulations of self- and Xe diffusivity in uranium mononitride including chemistry and irradiation effects

A combination of density functional theory and empirical potential atomic scale simulations have been used to determine a model for defect stability and mobility in uranium mononitride (UN), as a function of temperature (T) and N 2 partial pressure (p N 2 ). Using the model, predictions of hypo-stoichiometry under U-rich conditions compare favorably to CALPHAD calculations using the TAF-ID database. Furthermore, our predictions of U and N self-diffusivity are in good agreement with experiments carried out as a function of T at specific partial pressures under thermal equilibrium. The validated atomic scale data have then been implemented within a cluster dynamics method to simulate irradiation-enhanced defect concentrations. All defects and clusters studied have significantly enhanced concentrations, with respect to thermal equilibrium, as T is lowered. The irradiation-enhanced Xe diffusivity is compared to post-irradiation annealing and in-pile experiments. In conclusion, the contributions of various defects and clusters to non-stoichiometry, self-diffusivity, and Xe diffusivity are discussed.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Understanding the E balance for water management in hydroxide exchange membrane fuel cells

As a key challenge for hydroxide exchange membrane fuel cells (HEMFCs), understanding water management deeply is critical for performance and durability improvement. Here, in this work, we show that the balance between water generation and phase-change-induced (PCI) flow is the main factor controlling cell voltage over a wide range of conditions where the cells are vulnerable to severe flooding. The regulation of flooding by heat generation can be reflected by a stable voltage with increase of current density in the polarization curve. This PCI balance voltage (E balance ), which determines the shape of polarization curve, is modeled as a function of cell operating conditions and gas diffusion layer (GDL) properties. Temperature, pressure, and thermal conductivity of GDL were found important for tuning the level of E balance , both in HEMFCs and proton exchange membrane fuel cells. The understanding of E balance will help to generate strategies for resolving flooding in HEMFCs, and it offers a new perspective for polarization curve interpretation.

25 ENERGY STORAGE↗
DOE OSTI2021

Using a Chromatographic Pseudophase Model To Elucidate the Mechanism of Olefin Separation by Silver(I) Ions in Ionic Liquids

Silver(I) ions undergo selective olefin complexation and have been utilized in various olefin/paraffin separation techniques such as argentation chromatography and facilitated transport membranes. Ionic liquids (ILs) are solvents known for their low vapor pressure, high thermal stability, low melting points, and ability to promote a favorable solvation environment for silver(I) ion–olefin interactions. To develop highly selective separation systems, a fundamental understanding of analyte partitioning to the stationary phase and the thermodynamic driving forces behind solvation is required. In this study, a chromatographic model treating silver(I) ions as a pseudophase is constructed and employed for the first time to investigate the olefin separation mechanism in silver(I) salt/IL mixtures. Stationary phases containing varying amounts of noncoordinated silver(I) salt ([Ag + ][NTf 2 – ]) dissolved in the 1-decyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide ([C 10 MIM + ][NTf 2 – ]) IL are utilized to determine the partition coefficients of various analytes including alkanes, alkenes, alkynes, aromatics, aldehyde, esters, and ketones. As ligand coordination to silver(I) ions is known to lower its olefin complexation capability, this study also examines two different types of coordinated silver(I) ion pseudophases, namely, monocoordinated silver(I) salt ([Ag + (1-decyl-2-methylimidazole, DMIM)][NTf 2 – ]) and dicoordinated silver(I) salt ([Ag + (1-methylimidazole, MIM)(DMIM)][NTf 2 – ]). The extent of olefin partitioning to the coordinated silver(I) ion pseudophases over the carrier gas and IL decreased by up to two orders of magnitude. Values for enthalpy, entropy, and free energy of solvation were determined for the three silver(I) ion-containing systems. Olefin retention was observed to be enthalpically dominated, while ligand coordination to the silver(I) ion pseudophase resulted in variations for both enthalpic and entropic contributions to the free energy of solvation. Furthermore, the developed model can be used to study chemical changes that occur in silver(I) ions over time as well as identify optimal silver(I) salt/IL mixtures that yield high olefin selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Substituted ALPO-5 Zeolites as Promising O 2 Sorption Pump Materials: A Density Functional Theory Study

Many chemical processes depend on having an environment that is low in oxygen partial pressure (P O2 < 100 Pa); sorption pumps are a promising route to establishing that environment by either oxygen pumping or oxygen separation from an inert gas. Near ambient sorption-based processes rely on either pressure or thermal swings, requiring no moving parts, no electricity, and neither very high nor very low temperatures. In this work, we use ab initio calculations to explore zeolites as a class of materials for sorption based oxygen pumping/separation. Our calculations indicate that while the neat ALPO-5 zeolite does not adsorb O 2 , O 2 does adsorb on zeolites selectively substituted with transition metals and metalloids and hence, can enable separation and pumping. ALPO-5 substituted with Si, Ge, Sn, Pd, Pt, Ti, V, Cr, Mn, Zr, Mo, Hf, W, Ce, and Pr provides adsorption energies ranging from -0.19 to -3.92 eV, (-) indicates exothermic process. Additionally, we provide a comprehensive understanding of what controls the adsorption energy: 1) the substi-tutions must be able to adopt an oxidation state that is more positive than the cation it replaces, and 2) the size of the pore into which the O 2 adsorbs to the wall. Additionally, we conduct a ther-modynamic analysis of a thermal swing cycle to approximate the optimal O 2 binding energy for 2 low energy O 2 pumping/separation. We find that the minimum energy cost likely occurs when the adsorption energy is in the range of 0.75 – 1.00 eV (72 – 97 kJ·mol -1 ), which corresponds to Ge, V, Pt, or Ce substituted ALPO-5.

36 MATERIALS SCIENCE↗
DOE OSTI2025

All 2D Material Printed Diodes and Circuits on Paper for Sustainable Electronics

Sustainable electronics aim to reduce environmental impact by using ecofriendly materials, energy-efficient manufacturing, and recyclable components. However, existing approaches rely on complex, resource-intensive methods, rare metals, or nanomaterials with limited stability as well as plastic substrates, raising sustainability issues. Solution-processed two-dimensional (2D) materials offer a promising alternative: water-based and biocompatible conductive, semiconductive, and insulating 2D material inks can be produced with scalable techniques and are suitable for the fabrication of fully printed devices on low-cost and biodegradable paper substrates. However, 2D material only and fully printed diodes on paper have not yet been reported. Here, we demonstrate fully inkjet-printed 2D material-based diodes on paper using metal-insulator-semiconductor and metal-insulator-metal-semiconductor architectures. Water-based graphene and MoS2 inks, prepared by liquid-phase exfoliation, are used for the metallic and insulating films, while electrochemical exfoliation is used to produce the semiconducting MoS2 ink. The highest forward-to-reverse current ratio obtained is 330 (at ±2 V), while the forward current density is 1 mA/cm2 (at 1 V), making the diode performance comparable to the best solution-processed diodes reported so far. However, in contrast to previous works, fabrication occurs entirely at room temperature and ambient pressure, without using high-pressure sputtering, thermal evaporation, and any precious metal ink. The devices maintain stable performance under bending up to strain of 4% over 10,000 cycles. Finally, the diodes are successfully integrated with other 2D-material based electrical components to realize fully printed RC circuits, differentiators, integrators, and AC-to-DC converters onto paper, hence demonstrating the suitability of our approach for sustainable and disposable integrated circuits.

2D materials↗
DOE OSTI2022

Toroidal modeling of energetic passing particle drift kinetic effects on tearing mode stability

Abstract Drift kinetic effects of the neutral beam injection induced passing energetic particles (EPs) on the linear stability of the n = 1 tearing mode (TM) (with the dominant poloidal harmonic of m = 2) are numerically investigated utilizing the MARS-K code (Liu et al 2008 Phys. Plasmas 15 112503), in a tokamak plasma with finite equilibrium pressure and anisotropic thermal transport. In the low plasma pressure regime, it is found that co- (counter-) passing EPs stabilize (destabilize) the TM, agreeing with previous studies. However, as the plasma pressure increases beyond a critical value, it is found that co-passing EPs also destabilize the mode. An in-depth analysis reveals that the net effect of co-passing EPs is a result of competition between the stabilizing contribution from the non-adiabatic drift kinetic terms and the destabilizing contribution associated with adiabatic terms, with the latter becoming more dominant at higher equilibrium pressure. Non-perturbative magnetohydrodynamic-kinetic hybrid modeling also finds that co- and counter-passing EPs modify the TM eigenfunction differently, with the counter-passing EPs enhancing the sideband harmonics. Furthermore, effects of the plasma resistivity and toroidal rotation, as well as that of the equilibrium distribution of EPs in the particle pitch angle space, are also investigated, showing asymmetric results on the TM stability between the co- and counter-passing EPs. The first order finite orbit width correction is found to be stabilizing with co-passing EPs and destabilizing with counter-passing particles. Finally, drift resonances between passing EPs and the TM induce finite frequency to the mode and generate finite net torques inside the plasma, due to the neoclassical toroidal viscosity and the Reynolds stress associated with 3D perturbations.

Physics↗
DOE OSTI2024

A Hybrid Heavy Duty Diesel Power System for Off-Road Applications—Concept Validation

A multiyear power system R&D program was completed with the objective of developing an off-road hybrid heavy duty diesel engine with front end accessory drive-integrated energy storage. This system was validated to deliver 10.5–25.6% reduction in fuel consumption over current Tier 4 Final-based 18L diesel engines, over various off-road machine application cycles. The power system consisted of a downsized heavy-duty diesel 13L engine containing advanced combustion technologies, capable of elevated peak cylinder pressures and thermal efficiencies, thermal barrier coatings, exhaust waste heat recovery via SuperTurbo™ turbocompounding, and hybrid energy assisting and recovery through both mechanical and electrical systems. Following the concept definition, design, and analysis phases of the program, the final phase focused on building and validating the performance and efficiency in laboratory tests. While aspects of the system such as start/stop and reduced off-road cooling package energy losses were only analytically evaluated, the main 13L concept engine with full hybrid system was successfully built and tested in steady-state and in transient certification and real-world application cycles. Extensive simulations in Caterpillar's DYNASTY™ software environment utilized the validation test data to assess performance more fully and confidently over varied cycles and strategies. An average fuel consumption reduction of 17.9% was realized, and the majority (~13%) of the benefit stemmed from the core concept 13L engine. In conclusion, a total cost of ownership analysis provides context to commercial viability and where adoption focus should be placed.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Watching a hydroperoxyalkyl radical (•QOOH) dissociate

A prototypical hydroperoxyalkyl radical (•QOOH) intermediate, transiently formed in the oxidation of volatile organic compounds, was directly observed through its infrared fingerprint and energy-dependent unimolecular decay to hydroxyl radical and cyclic ether products. Direct time-domain measurements of •QOOH unimolecular dissociation rates over a wide range of energies were found to be in accord with those predicted theoretically using state-of-the-art electronic structure characterizations of the transition state barrier region. Unimolecular decay was enhanced by substantial heavy-atom tunneling involving O-O elongation and C-C-O angle contraction along the reaction pathway. Master equation modeling yielded a fully a priori prediction of the pressure-dependent thermal unimolecular dissociation rates for the •QOOH intermediate—again increased by heavy-atom tunneling—which are required for global models of atmospheric and combustion chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗