Search NASA⌕ Search

SEARCH · Search NASA

Results for “transport limitations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Delineating Confinement Regimes for Nafion Thin Films via Simultaneous QCM-D and Spectroscopic Ellipsometry

Proton-conducting ionomers used in electrodes of electrochemical devices form nanometer-scale films covering metallic catalyst surfaces, wherein they experience confinement and interfacial effects absent in the bulk polymer. This confinement alters the physical properties of the ionomer film, which is postulated to increase the density and is attributed to the transport limitations observed in fuel-cell electrodes. Despite studies showing reduced swelling, no systematic measurement has validated this phenomenon by demonstrating both densification and stiffening as the film gets thinner. Here, this study aims to fill this gap by reporting the humidity-driven changes in swelling, mass uptake, and density of Nafion ionomer films cast at varying thicknesses (10–320 nm) onto a gold-plated sensor. The films were simultaneously probed during humidification using spectroscopic ellipsometry (SE) and a quartz crystal microbalance with dissipation (QCM-D), which allowed for determination of the density and shear stiffness. The effects of confinement were prominently observed below ∼30 nm, with films showing increased density along with decreased swelling and mass uptake during hydration. In addition, the confined films show a negative excess volume upon initial water sorption, implying a larger proportion of absorbed water might bound to ionic groups in accord with notion of localized densification.

Espinet, Kevin B. [University of California, Berke↗
DOE OSTI2021

Effects of Applied Interfacial Pressure on Li-Metal Cycling Performance and Morphology in 4 M LiFSI in DME

Lithium-metal anodes can theoretically enable 10x higher gravimetric capacity than conventional graphite anodes. However, Li-metal anode cycling has proven difficult due to porous and dendritic morphologies, extensive parasitic solid electrolyte interphase reactions, and formation of dead Li. We systematically investigate the effects of applied interfacial pressure on Li-metal anode cycling performance and morphology in the recently developed and highly efficient 4 M lithium bis(fluorosulfonyl)imide in 1,2-dimethoxyethane electrolyte. We present cycling, morphology, and impedance data at a current density of 0.5 mA/cm 2 and a capacity of 2 mAh/cm 2 at applied interfacial pressures of 0, 0.01, 0.1, 1, and 10 MPa. Cryo-focused ion beam milling and cryo-scanning electron microscopy imaging in cross section reveal that increasing the applied pressure during Li deposition from 0 to 10 MPa leads to greater than a fivefold reduction in thickness (and therefore volume) of the deposited Li. This suggests that pressure during cycling can have a profound impact on the practical volumetric energy density for Li-metal anodes. A “goldilocks zone” of cell performance is observed at intermediate pressures of 0.1–1 MPa. Increasing pressure from 0 to 1 MPa generally improves cell-to-cell reproducibility, cycling stability, and Coulombic efficiency. However, the highest pressure (10 MPa) results in high cell overpotential and evidence of soft short circuits, which likely result from transport limitations associated with increased pressure causing local pore closure in the separator. All cells exhibit at least some signs of cycling instability after 50 cycles when cycled to 2 mAh/cm 2 with thin 50 μm Li counter electrodes, though instability decreases with increasing pressure. In contrast, cells cycled to only 1 mAh/cm 2 perform well for 50 cycles, indicating that capacity plays an important role in cycling stability.

25 ENERGY STORAGE↗
DOE OSTI2021

Tandem Electrocatalytic CO 2 Reduction with Efficient Intermediate Conversion over Pyramid-Textured Cu–Ag Catalysts

If combined with renewably generated electricity, electrochemical CO 2 reduction (E-CO 2 R) could be used as a sustainable source of chemicals and fuels. Tandem catalysis approaches are attractive for providing the product selectivity, which would be required for commercial applications. Here, we demonstrate a two-step tandem electrocatalytic E-CO 2 R with efficient conversion of the intermediate species. The catalyst scaffold is Si(100), which is etched to form a textured surface consisting of micron-sized pyramid structures with the {111} facets. Two metals are used in the electrocatalytic cascade: Ag is employed to perform a two-electron reduction of CO 2 to the intermediate CO, and Cu performs conversion to more reduced products. Using high-angle physical vapor deposition, we form separated, micron-scale areas of the two electrocatalysts on opposite sides of the pyramids, with their relative surface coverages being tunable with the deposition angle. Compared to the textured scaffolds with blanket Ag and Cu used as controls, bimetallic pyramid tandem catalysts have higher current densities and much lower faradic efficiencies (FE) for CO. These effects are due to efficient conversion of the CO formed on Ag to more reduced products on Cu. Methane is the main product to be enhanced by the cascade pathway: a bimetallic catalyst with approximately equal coverages of Ag and Cu produces methane with a FE of 62% at -1.1 V RHE , corresponding to a partial current density of 12.7 mA cm -2 . We estimate an intermediate conversion yield for the CO intermediate of 80-90%, which is close to the mass-transport limited value predicted by reaction-diffusion simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effects of Surface Hydrophobicity on Catalytic Transfer Hydrogenation of Styrene with Formic Acid in a Biphasic Mixture

Transfer hydrogenation (TH) of unsaturated hydrocarbons with formic acid (FA) is an attractive processing pathway for the reduction of lignocellulosic pyrolysis oils. The low solubility of hydrophobic bio-oil species in water and FA in oil necessitates the use of a biphasic system as the reaction environment. Here, we report the effects of Pd/silica catalyst surface wettability on the TH reaction rate. Modification of the surface with short chain (C1–C4) alkyl silanes resulted in an increase in the reaction rate as compared to the unmodified catalyst. In contrast, modification of the surface with sulfonate (hydrophilic) and C18 alkyl silanes (hydrophobic) resulted in a decrease in the reaction rate as compared to the unmodified catalyst. Here, the results are discussed in terms of the catalyst interfacial activity and relative affinity of the reagents to the Pd active sites. An observed change in the apparent reaction order in styrene for a hydrophilic catalyst suggests that changing catalyst surface wettability from hydrophilic to hydrophobic resulted in a switch from a transport-limited to a kinetic-limited reaction regime.

09 BIOMASS FUELS↗
DOE OSTI2021

Heterostructured Lepidocrocite Titanate-Carbon Nanosheets for Electrochemical Applications

Lepidocrocite-type titanates that reversibly intercalate sodium ions at low potentials (~0.6 V vs Na/Na + ) are promising anode candidates for sodium-ion batteries. However, large amounts of carbon additives are often used to improve their electrical conductivity and overcome poor cycling performance in the electrode composites. To ameliorate electronic transport issues of lepidocrocite titanate (K 0.8 Ti 1.73 Li 0.27 O 4 , KTL) in sodium-ion batteries, we have designed and synthesized heterostructures of exfoliated lepidocrocite-type titanium oxide (LTO) nanosheets with alternating carbon layers via a solution-based self-assembly approach. Positively charged dopamine (Dopa) was used as the carbon precursor and intercalated between negatively charged exfoliated titania nanosheets through electrostatic interaction. Dopa-intercalated LTO was then annealed under argon to form conductive carbon layers between titania sheets. The carbon content in the heterostructures was controlled by modifying the self-assembly conditions (i.e., pH, stirring duration, and Dopa-to-LTO ratio). Electrodes were prepared using carbonized heterostructures (LTO-C) without adding more carbon to the composites and tested in sodium half-cell configurations. Further, higher capacities and improved capacity retention over 250 cycles and lower impedance were observed, as the carbon content of LTO-C heterostructures was increased from 0% (LTO nanosheets) to 30%. These results indicate that the self-assembly approach for 2D heterostructured electrode materials is a promising strategy to overcome electronic transport limitations of layered transition-metal oxides and improve their electrochemical performance for next-generation energy storage applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Depolymerization as a Design Strategy: Depolymerization Etching of Polymerization-Induced Microphase Separations

Thermally triggered depolymerization has traditionally been viewed through the lens of sustainability and recycling, not as a constructive tool for materials design. Herein, we show that selective, thermally triggered depolymerization to gaseous monomer serves as a solvent-free strategy for generating porosity in nanostructured polymer materials, offering a means to bypass the mass transport limitations inherent in conventional solution-based etching. As a demonstration platform, we employed polymerization-induced microphase separation (PIMS) to generate disordered bicontinuous block copolymer structures with embedded depolymerizable domains. By incorporating a methacrylate block susceptible to thermal depolymerization within a cross-linked, depolymerization-resistant styrenic matrix, we developed a process we term depolymerization etching of polymerization-induced microphase separations (DEPIMS). This approach enables highly selective and efficient domain removal via reversion to monomer to produce mesoporous materials with high surface areas (>200 m 2 /g). Subsequent surface functionalization yielded mesoporous adsorbents with tunable uptake kinetics and among the highest dye adsorption capacities reported for PIMS-derived materials, demonstrating the adaptability of the DEPIMS platform for chemical separations. DEPIMS can also be extended to a gram-scale, one-pot approach to yield mesoporous materials with recoverable monomer in under 12 h. These findings reposition thermal depolymerization from a sustainability tool to a broadly enabling strategy for scalable, on-demand fabrication of functional nanostructured materials.

Depolymerization↗
DOE OSTI2022

Pathways for the Formation of C 2+ Products under Alkaline Conditions during the Electrochemical Reduction of CO 2

Establishing how Cu facilitates the electrochemical CO 2 reduction reaction (CO2RR) to C 2+ products remains a critical challenge. Under typical reaction conditions, the pH near the electrode is considerably more alkaline than that in the bulk due to mass transport limitations. Challenges with probing alkaline pathways using computational methods have limited understanding of the CO2RR under experimentally relevant conditions. In this work, using the Volmer reaction on Cu (100), we demonstrate that predicted activation barriers can substantially differ between acidic and alkaline pathways. We compute reaction energetics for alkaline *CO protonation and find that, while the formation of *CHO is preferred thermodynamically, the formation of *COH is favored kinetically at high overpotential. However, we find formation of *CHO via reaction of *H and *CO feasible at room temperature. Further, we report potential-dependent energetics for forming the first C-C bond in CO2RR and find that CO dimerization likely dominates. Finally, we investigate how long-range van der Waals interactions impact our results by comparing to the meta-GGA B97M-rV.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Pathways to Electrochemical Ironmaking at Scale Via the Direct Reduction of Fe 2 O 3

Electrochemical ironmaking can provide an energy efficient, zero-emissions alternative to traditional methods of ironmaking, but the scalability of low-temperature electrochemical cells may be constrained by reactor throughput and the availability of acceptable feedstocks. Electrodes directly converting solid iron-oxide particles to metal circumvent traditional mass-transport limitations but are sensitive to both the particle size and nanoscale morphology of reactants. Furthermore, the effect of these properties on reactor throughput has not been systematically studied at model electrowinning surfaces. Here, we have used size-controlled, homologous α-Fe 2 O 3 particles to study how the nanoscale morphology of oxides influences the obtainable current density toward Fe metal and integrated these results in a technoeconomic model for alkaline iron electrowinning systems. Micron-scale α-Fe 2 O 3 with nanoscale porosity can be used to form Fe at current densities commensurate with industrial water electrolysis (>0.6 A cm –2 ) in the absence of external convection, providing a path to cost-competitive and scalable ironmaking using electrochemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Translating Fundamental Insights into Ag-Based Bimetallic Electrocatalysts to Anion-Exchange Membrane Fuel Cells

To address challenges of high costs and scalability for fuel cells, it is essential to develop af-fordable and earth-abundant materials that are Pt-group-metal (PGM)-free. Recent advance-ments in PGM-free electrocatalysis for the oxygen reduction reaction (ORR) in alkaline media show that high catalyst loadings are needed to achieve high reaction rates; however, there are associated mass transport limitations. To address this issue, we develop low-loading ionomer-less Ag-bimetallic thin films by alloying with 3d block elements or Sn. We bridge knowledge from fundamental rotating disk electrode (RDE) studies to gas-diffusion cathodes in high-temperature anion-exchange membrane fuel cells (HT-AEMFCs), resulting in high-activity ORR catalysis and peak power densities up to 1.2 W cm-² geo for the Ag-Sn and Ag-Co alloys. Here, experimental post-characterization and theoretical calculations reveal small Co or Sn oxide nano-islands on Ag as likely active sites enhancing ORR activity, ultimately offering these low-loading PGM-free ORR materials as a viable path towards sustainable energy conversion.

Catalysts↗
DOE OSTI2026

Pulsed Electrolysis Promotes Catalyst Activity in Dilute CO 2 Streams

Industrial CO 2 streams vary widely in composition, from pure to as low as 3%, posing challenges for purification or direct conversion. Electrochemical reduction offers a route for converting dilute CO 2 streams but faces severe mass transport limitations. This study demonstrates that pulsed electrolysis effectively overcomes these limitations, enhancing CO 2 electroreduction across variable feed compositions and current densities, particularly at low CO 2 concentrations and high current densities. At 25% CO 2 and 400 mA cm −2 , pulsing improved selectivity from 25.6 to 78.6%, production rate from 13.7 to 21.0 mol m −2 h −1 , and energy productivity from 0.77 to 2.59 mol kWh −1 . A dynamic, multiphysics continuum model confirms a 64% increase in CO 2 concentration within the catalyst layer during pulsing, resolving the transient chemical microenvironment. These findings establish pulsed electrolysis as a viable strategy for converting dilute industrial CO 2 streams into valuable feedstocks, bypassing costly pre-separation.

Orfali, Dania Muhieddine [New York University (NYU↗
DOE OSTI2022

Selective Removal of Barium and Hardness Ions from Brackish Water with Chemically Enhanced Electrodialysis

The use of a nonconventional water resource for energy and industrial applications often requires extraction of low-level undesirable ions from matrices of benign dominant ions. In this study, the selective extraction of Ba 2+ and Mg 2+ from synthetic brine solutions was evaluated using strong acid cation-exchange membranes modified with the surface deposition of macrocyclic molecules including crown ethers and calixarenes. Compared to the bare membrane, vinylbenzo-18-crown-6 (VB18C6) and calix[4]arene-amended membranes showed increased selectivity for Ba 2+ and Mg 2+ with respect to the dominant ion (Na + ) by up to fourfolds, with the calix[4]arene-modified membrane achieving more selective separation than VB18C6. Optimal selectivity was achieved at a moderate-to-high current density (3.1–6.3 mA/cm 2 ), which was attributed to the alleviation of transport limitation in the boundary layer by the surface modification. Amendment of a calix[4]arene derivative with a crown-6 “boot strap” and two carboxylic groups resulted in reduced selectivity due to the formation of strong complexes with divalent ions. Furthermore, these results show that surface deposition of ion sequestrants can be a versatile approach to improve the membrane’s selectivity; however, the performance is sensitive to feed water salinity, current loading, and the macrocycle-ion chemistry, where there is a trade-off between ion affinity and mobility.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effects of Polymer Morphology on Solvent and Catalyst Accessibility during Polyethylene and Polystyrene Autoxidation

Efficient catalytic deconstruction of plastics requires facile solvent and catalyst access to polymer substrates to minimize mass transfer effects. Autoxidation using Co(II) acetate, Mn(II) acetate, and a radical carrier in acetic acid is a promising strategy to deconstruct mixed plastic waste, yet the role of polymer morphology in governing solvent and catalyst accessibility remains poorly understood. Here, in situ simultaneous small- and wide-angle X-ray scattering (SAXS/WAXS), complemented by X-ray fluorescence (XRF) imaging and high-pressure differential scanning calorimetry (DSC), were used to elucidate interactions between acetic acid, a Co/Mn catalyst solution, and semicrystalline polyethylene (PE) and amorphous polystyrene (PS) from room temperature to 160 °C. In PE, acetic acid and catalyst access were confined to amorphous regions and cryomilled particle interfaces at room temperature, while crystalline lamellae remained intact after soaking for up to 34 h. Increasing temperature enabled solvent uptake into PE, followed by solvent-assisted softening above 100 °C, and a modest melting-point depression that removed lamellar transport barriers upon melting. Conversely for PS, acetic acid penetrated the glassy polymer without inducing chain mobility until the glass transition was reached, above which the observed structural changes were consistent with enhanced segmental mobility which enabled bulk penetration. These results suggest that polymer morphology and thermally activated physical transitions arising from diffusion and polymer–solvent interactions can influence whether autoxidation of plastics is transport-limited or kinetically controlled, providing a framework for aligning reaction conditions with reaction outcomes.

09 BIOMASS FUELS↗
DOE OSTI2023

Coupling nitrate capture with ammonia production through bifunctional redox-electrodes

Abstract Nitrate is a ubiquitous aqueous pollutant from agricultural and industrial activities. At the same time, conversion of nitrate to ammonia provides an attractive solution for the coupled environmental and energy challenge underlying the nitrogen cycle, by valorizing a pollutant to a carbon-free energy carrier and essential chemical feedstock. Mass transport limitations are a key obstacle to the efficient conversion of nitrate to ammonia from water streams, due to the dilute concentration of nitrate. Here, we develop bifunctional electrodes that couple a nitrate-selective redox-electrosorbent (polyaniline) with an electrocatalyst (cobalt oxide) for nitrate to ammonium conversion. We demonstrate the synergistic reactive separation of nitrate through solely electrochemical control. Electrochemically-reversible nitrate uptake greater than 70 mg/g can be achieved, with electronic structure calculations and spectroscopic measurements providing insight into the underlying role of hydrogen bonding for nitrate selectivity. Using agricultural tile drainage water containing dilute nitrate (0.27 mM), we demonstrate that the bifunctional electrode can achieve a 8-fold up-concentration of nitrate, a 24-fold enhancement of ammonium production rate (108.1 ug h −1 cm −2 ), and a >10-fold enhancement in energy efficiency when compared to direct electrocatalysis in the dilute stream. Our study provides a generalized strategy for a fully electrified reaction-separation pathway for modular nitrate remediation and ammonia production.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Effect of crystallite geometries on electrochemical performance of porous intercalation electrodes by multiscale operando investigation

Lithium-ion batteries are yet to realize their full promise because of challenges in the design and construction of electrode architectures that allow for their entire interior volumes to be reversibly accessible for ion storage. Electrodes constructed from the same material and with the same specifications, which differ only in terms of dimensions and geometries of the constituent particles, can show surprising differences in polarization, stress accumulation and capacity fade. Here, using operando synchrotron X-ray diffraction and energy dispersive X-ray diffraction (EDXRD), we probe the mechanistic origins of the remarkable particle geometry-dependent modification of lithiation-induced phase transformations in V2O5 as a model phase-transforming cathode. A pronounced modulation of phase coexistence regimes is observed as a function of particle geometry. Specifically, a metastable phase is stabilized for nanometre-sized spherical V2O5 particles, to circumvent the formation of large misfit strains. Spatially resolved EDXRD measurements demonstrate that particle geometries strongly modify the tortuosity of the porous cathode architecture. Greater ion-transport limitations in electrode architectures comprising micrometre-sized platelets result in considerable lithiation heterogeneities across the thickness of the electrode. These insights establish particle geometry-dependent modification of metastable phase regimes and electrode tortuosity as key design principles for realizing the promise of intercalation cathodes. Designing electrode architectures for Li-ion batteries that can be reversibly accessible for ion storage can be challenging. Using operando techniques the mechanistic origin of lithiation-induced phase transformations in a V2O5 model cathode is now clarified.

Luo, Yuting↗
DOE OSTI2020

Mesoporous silica-encapsulated gold core–shell nanoparticles for active solvent-free benzyl alcohol oxidation

Silica-encapsulated gold core@shell nanoparticles (Au@SiO2 CSNPs) were synthesized via a bottom-up procedure and used to catalyze the selective oxidation of benzyl alcohol. The pore size, morphology, crystallinity and composition of Au@SiO2 was evaluated using non-local density functional theory, transmission electron microscopy, high-energy x-ray diffraction and inductively coupled plasma-mass spectroscopy, respectively. The nanoparticles exhibit a mesoporous shell with an average thickness of 25.5 Å which can enhance selectivity via preferential transport of the desired product (i.e., benzaldehyde) relative to larger, undesired products (i.e, benzoic acid/benzyl benzoate). GC-FID analysis revealed the addition of potassium carbonate to the solvent-free oxidation of benzyl alcohol increased conversion from 17.3 to 60.4% while decreasing selectivity from 98.7 to 75.0%. Under equivalent conditions, a bare gold nanoparticle control catalyst deposited on a silica support with a similar gold surface area took 6 times as long to reach the same conversion, achieving only 49.4% selectivity. These results suggest that the pore size distribution within the inert silica shell of Au@SiO2 CSNPs inhibits the formation of undesired products to facilitate the selective oxidation of benzaldehyde despite a basic environment, which reduces selectivity under typical conditions. The CSNPs demonstrated a much lower activation energy than the Au-SiO2 control catalyst, 37 ± 1.9 kJ/mol and 72 ± 7.1 kJ/mol, respectively. Thiele modulus analysis indicates the CSNP pore structure does not create a mass transport limitation due to the nano-scale path of diffusion through the pore structure to the active surface. The lower activation energy and mesopore distribution together suggest the Au@SiO2 catalyst demonstrates higher activity through beneficial in-pore orientation, both reducing competitive adsorption and promoting a single, lower activation energy mechanistic pathway.

benzyl alcohol oxidation, catalysis, confinement↗
DOE OSTI2021

Progress on continuum modeling of lithium–sulfur batteries

While lithium–sulfur batteries are a promising next-generation chemistry devices due to their high theoretical energy density, commercialization has been slow due to low coulombic efficiency and poor cycle life. This review explores the ways in which continuum modeling contributes to the understanding of lithium–sulfur (LiS) battery mechanisms and cell-level performance through the lens of micro- and macroscale phenomena. We examine different approaches to modeling important physical phenomena such as reaction mechanisms, cathode microstructure, shuttling, nucleation and precipitation, and transport limitations. This paper also emphasizes the significance and challenge of connecting typical modeling parameters and assumptions to systems-level metrics of a standard state-of-art high performing lithium–sulfur cell. Particularly important, the considerations for high energy density cells and the areas where continuum models can facilitate better collaboration are discussed. Here, we also summarize a few selected works to highlight experimentally-driven modeling, use of electroanalytical techniques, and parameter identification approaches to enable model-based design and advanced battery management systems.

25 ENERGY STORAGE↗