Search NASA⌕ Search

SEARCH · Search NASA

Results for “ultrasonic impacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Testing of a Multi-Stringer Post-Buckled Panel with Incremental Damage Detection

A multi-stringer panel was designed and tested to produce a failure mode of skin-stiffener delamination due to compression loading of a post-buckled skin to support the validation of high-fidelity progressive damage failure analysis modeling. The test procedure included multiple methods of data acquisition ranging from multiple strain gages, front and back digital image correlation, passive thermography, acoustic emission, and ultrasonic inspection to capture key events and damage progression prior to catastrophic failure. Detailed data showing the initial stiffness, onset of skin buckling, buckled mode shape, damage initiation load, damage propagation morphology, and peak load was captured. Two panel configurations were tested. The first had a Teflon insert placed in the interface between the skin and the stiffener flanges adjacent to the center skin bay. The second was subjected to impact damage to the skin-stiffener flange. In each case, continuously-loaded-to-failure tests were conducted first with passive thermography being used exclusively to determine key damage events. Then, incrementally loaded tests were completed where ultrasonic inspections were conducted between each increment. The amount of load applied between each increment was determined based on the in-situ damage detection provided by the passive thermography system. The results of the testing showed a complex delamination growth pattern which migrated between ply interfaces through matrix splits in the upper skin ply of the panel. The result of the testing produced very detailed data which will prove to be useful for validation of delamination growth and migration predictions from progressive damage failure analysis methods.

Jason Action↗
NASA NTRS1999

Thermally Stable, Piezoelectric and Pyroelectric Polymeric Substrates

A thermally stable, piezoelectric and pyroelectric polymeric substrate was prepared. This thermally stable, piezoelectric and pyroelectric polymeric substrate may be used to prepare electromechanical transducers, thermomechanical transducers, accelerometers. acoustic sensors, infrared sensors, pressure sensors, vibration sensors, impact sensors, in-situ temperature sensors, in-situ stress/strain sensors, micro actuators, switches, adjustable fresnel lenses, speakers, tactile sensors. weather sensors, micro positioners, ultrasonic devices, power generators, tunable reflectors, microphones, and hydrophones. The process for preparing these polymeric substrates includes: providing a polymeric substrate having a softening temperature greater than 1000 C; depositing a metal electrode material onto the polymer film; attaching a plurality of electrical leads to the metal electrode coated polymeric substrate; heating the metal electrode coated polymeric substrate in a low dielectric medium; applying a voltage to the heated metal electrode coated polymeric substrate to induce polarization; and cooling the polarized metal electrode coated polymeric electrode while maintaining a constant voltage.

Simpson, Joycely O.↗
NASA NTRS1999

Method of Making Thermally Stable, Piezoelectric and Proelectric Polymeric Substrates

A thermally stable, piezoelectric and pyroelectric polymeric substrate was prepared. This thermally stable, piezoelectric and pyroelectric polymeric substrate may be used to prepare electromechanical transducers, thermomechanical transducers, accelerometers, acoustic sensors, infrared sensors, pressure sensors, vibration sensors, impact sensors. in-situ temperature sensors, in-situ stress/strain sensors, micro actuators, switches, adjustable fresnel lenses, speakers, tactile sensors, weather sensors, micro positioners, ultrasonic devices, power generators, tunable reflectors, microphones, and hydrophones. The process for preparing these polymeric substrates includes: providing a polymeric substrate having a softening temperature greater than 100 C; depositing a metal electrode material onto the polymer film; attaching a plurality of electrical leads to the metal electrode coated polymeric substrate; heating the metal electrode coated polymeric substrate in a low dielectric medium: applying a voltage to the heated metal electrode coated polymeric substrate to induce polarization; and cooling the polarized metal electrode coated polymeric electrode while maintaining a constant voltage.

Simpson, Joycelyn O.↗
NASA NTRS2002

Thermally Stable, Piezoelectric and Pyroelectric Polymeric Substrates and Method Relating Thereto

A thermally stable, piezoelectric and pyroelectric polymeric substrate was prepared, This thermally stable, piezoelectric and pyroelectric polymeric substrate may be used to prepare electromechanical transducers, thermomechanical transducers, accelerometers, acoustic sensors, infrared sensors, pressure sensors, vibration sensors, impact sensors. in-situ temperature sensors, in-situ stress/strain sensors, micro actuators, switches. adjustable fresnel lenses, speakers, tactile sensors, weather sensors, micro positioners, ultrasonic devices, power generators, tunable reflectors, microphones, and hydrophones. The process for preparing these polymeric substrates includes: providing a polymeric substrate having a softening temperature greater than 100 C; depositing a metal electrode material onto the polymer film; attaching a plurality of electrical leads to the metal electrode coated polymeric substrates; heating the metal electrode coated polymeric substrate in a low dielectric medium; applying a voltage to the heated metal electrode coated polymeric substrate to induce polarization; and cooling the polarized metal electrode coated polymeric electrode while maintaining a constant voltage.

Joycelyn O Simpson↗
NASA NTRS2017

Meal Replacement Mass Reduction and Integration Acceptability Study

NASA, in planning for long-duration missions, has an imperative to provide a food system with the necessary nutrition, acceptability, and safety to ensure sustainment of crew health and performance. The Orion Multi-Purpose Crew Vehicle (MPCV) and future exploration missions are mass constrained; therefore the team is challenged to reduce the mass of the food system by 10% while maintaining product safety, nutrition, and acceptability. Commercially available products do not meet the nutritional requirements for a full meal replacement in the spaceflight food system, and it is currently unknown if daily meal replacements will impact crew food intake and psychosocial health over time. The purpose of this study was to develop a variety of nutritionally balanced breakfast replacement bars that meet spaceflight nutritional, microbiological, sensorial, and shelf-life requirements, while enabling a 10% savings in food mass. To date, six nutrient-dense meal replacement bars (approximately 700 calories per bar) have been developed, using traditional methods of compression as well as novel ultrasonic compression technologies developed by Creative Resonance Inc. (Phoenix, AZ). The four highest rated bars were evaluated in the Human Exploration Research Analog (HERA) to assess the frequency with which actual meal replacement options may be implemented. Specifically, overall impact of bars on mood, satiety, digestive discomfort, and satisfaction with food. These factors are currently being analyzed to inform successful implementation strategies where crew maintain adequate food intake. In addition, these bars are currently undergoing shelf-life testing to determine long-term sensory acceptability, nutritional stability, qualitative stability of analytical measurements (i.e. water activity and texture), and microbiological compliance over two years of storage at room temperature and potential temperature abuse conditions to predict long-term acceptability. It is expected that this work will enable a successful meal replacement strategy to be implemented that will maintain crew food consumption and health, while informing exploration missions with appropriate mass savings expectations.

Sirmons, T.↗
DOE OSTI2021

Stepwise Dynamic Calibration of a Hydromechanical Simulation Using Time-Lapse Vertical Seismic Profile

This study aims to develop a methodology for calibrating subsurface stress changes through time-lapse Vertical Seismic Profiling (VSP) integration. The selected study site is the 13-10A injector well within the ongoing CO2-EOR operation of the Farnsworth Field Unit. The Time-lapse VSP dataset carries the combined effects of fluid substitution and mean effective stress changes, thereby providing a dataset amenable for the calibration of production and injection-induced stress changes. The concept is similar to calibrating a reservoir simulation model in that the process honor real field data to set up an inverse problem. The solution optimizes the independent and impactful geomechanical parameters that replicate the observed time-lapse seismic velocity changes. This stress calibration is enabled by 4D geomechanical modeling and the VSP Integration workflow. This calibration benefits from extensive geological, geophysical and geomechanical characterization through 3D seismic data, geophysical well logs, and core assessed as part of the 1D MEM conducted on the 13-10A subject well. These data are used to develop a site-specific rock physics model. The Biot Gassmann workflow combines rock physics and reservoir simulation outputs to determine the fluid substitution contribution to seismic velocity change. Additionally, modeled seismic velocity attributed to mean effective stress are determined from the geomechanical simulation outputs, and the stress-velocity relationship developed from the ultrasonic seismic velocity measurements on the extracted Morrow B core. A penalty function is then formed between the modeled seismic velocities and the observed time-lapse VSP dataset. Four independent and impactful geomechanical parameters have been determined. These are the bulk modulus and shear modulus for zero porosity and the shear and compressional seismic velocity to mean effective stress derivatives. The dataset of numerous coupled hydromechanical- geomechanical simulation realizations is built by combining variations of the four stated geomechanical parameters. A machine learning-assisted workflow comprised of an artificial neural network and a particle swarm optimizer are used to converge on the optimal geomechanical parameters. The successful execution of this workflow has affirmed the suitability of acoustic time-lapse measurements for 4D-VSP geomechanical stress calibration pending measurable stress sensitivities within the anticipated effective stress changes and the availability of suitable and reliable datasets for petroelastic modeling.

02 PETROLEUM↗
DOE OSTI2024

Very high cycle fatigue characteristics of laser beam powder bed fused AlSi10Mg: A systematic evaluation of part geometry

This study explores the influence of geometry and part size on defect distribution, melt pool size, and mechanical characteristics in laser beam powder bed fused (LB-PBF) AlSi10Mg. Five distinct geometries—hourglass, small rod, small block, large block, and large rod—were fabricated under identical process parameters. Fully reversed ultrasonic fatigue testing, operating at a frequency of 20 kHz, was conducted to assess the very high cycle fatigue properties. The findings indicated that part geometry had a major impact on the fatigue properties of the material in the very high cycle fatigue regime. Specimens machined from large rods and large blocks had the lowest porosity and highest fatigue resistance. Microstructural analysis indicated that hourglass, small rod, and small block specimens had shallower melt pools and overlap depths compared to other geometries. This observation suggests a higher cooling rate in specimens with smaller cross-sectional areas, leading to the increased presence of entrapped gas pores and a lack of fusion defects. Understanding the relationship between part geometry and fatigue properties in LB-PBF components offers insights for optimizing design and manufacturing processes in additive manufacturing applications.

AlSi10Mg↗
NASA NTRS2014

Ultrasonic/Sonic Jackhammer

The invention provides a novel jackhammer that utilizes ultrasonic and/or sonic vibrations as source of power. It is easy to operate and does not require extensive training, requiring substantially less physical capabilities from the user and thereby increasing the pool of potential operators. An important safety benefit is that it does not fracture resilient or compliant materials such as cable channels and conduits, tubing, plumbing, cabling and other embedded fixtures that may be encountered along the impact path. While the ultrasonic/sonic jackhammer of the invention is able to cut concrete and asphalt, it generates little back-propagated shocks or vibrations onto the mounting fixture, and can be operated from an automatic platform or robotic system. PNEUMATICS; ULTRASONICS; IMPACTORS; DRILLING; HAMMERS BRITTLE MATERIALS; DRILL BITS; PROTOTYPES; VIBRATION

Bar-Cohen, Yoseph↗
DOE OSTI2023

Dynamics of oil–water interface at the beginning of the ultrasonic emulsification process

A lot of effort has been dedicated in recent years towards understanding the basics of cavitation induced emulsification, mainly in the form of single cavitation bubbles. Regarding bulk acoustic emulsification, a lot less research has been done. In our here presented work we utilize advanced high-speed observation techniques in visible light and X-Rays to build upon that knowledge and advance the understanding of bulk emulsion preparation. During research we discovered that emulsion formation has an acute impact on the behavior of the interface and more importantly on its position relative to the horn, hence their interdependence must be carefully studied. We did this by observing bulk emulsification with 2 cameras simultaneously and corroborating these measurements with observation under X-Rays. Since the ultrasonic horns location also influences interface behavior, we shifted its initial position to different locations nearer to and further away from the oil–water interface in both phases. We found that a few millimeters distance between the horn and interface is not enough for fine emulsion formation, but that they must be completely adjacent to each other, with the horn being located inside the oil–water interface. We also observed some previously undiscovered phenomena, such as the splitting of the interface to preserve continuous emulsion formation, climbing of the interface up the horn and circular interface protrusions towards the horn forming vertical emulsion streams. Interestingly, no visible W/O emulsion was ever formed during our experiments, only O/W regardless of initial horn position.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1996

Detection of Delamination in Composite Beams Using Broadband Acoustic Emission Signatures

Delamination in composite structure may be caused by imperfections introduced during the manufacturing process or by impact loads by foreign objects during the operational life. There are some nondestructive evaluation methods to detect delamination in composite structures such as x-radiography, ultrasonic testing, and thermal/infrared inspection. These methods are expensive and hard to use for on line detection. Acoustic emission testing can monitor the material under test even under the presence of noise generated under load. It has been used extensively in proof-testing of fiberglass pressure vessels and beams. In the present work, experimental studies are conducted to investigate the use of broadband acoustic emission signatures to detect delaminations in composite beams. Glass/epoxy beam specimens with full width, prescribed delamination sizes of 2 inches and 4 inches are investigated. The prescribed delamination is produced by inserting Teflon film between laminae during the fabrication of composite laminate. The objectives of this research is to develop a method for predicting delamination size and location in laminated composite beams by combining smart materials concept and broadband AE analysis techniques. More specifically, a piezoceramic (PZT) patch is bonded on the surface of composite beams and used as a pulser. The piezoceramic patch simulates the AE wave source as a 3 cycles, 50KHz, burst sine wave. One broadband AE sensor is fixed near the PZT patch to measure the AE wave near the AE source. A second broadband AE sensor, which is used as a receiver, is scanned along the composite beams at 0.25 inch step to measure propagation of AE wave along the composite beams. The acquired AE waveform is digitized and processed. Signal strength, signal energy, cross-correlation of AE waveforms, and tracking of specific cycle of AE waveforms are used to detect delamination size and location.

Okafor, A. C.↗
DOE OSTI2026

Integration of the Biot–Gassmann Fluid Substitution Method and Machine Learning-Based Velocity–Stress Relationship for Estimating In Situ Stresses

Recent advancements have shown that in situ stresses can be reliably estimated through an integrated machine/deep learning (ML/DL)-based framework, which relies on models trained and validated using true triaxial ultrasonic velocity (TUV) experimental data that involve measurements of ultrasonic velocity in saturated rocks under varying stress configurations. However, when the goal is to interpret lower frequency measurements, it may be more appropriate to run experiments on dry rocks and then obtain Biot–Gassmann-derived equivalent saturated velocities (low-frequency approximation) and employ these quantities for training ML/DL models to predict in situ stress. Whether the dispersion effect of frequency on the velocity–stress relationship substantially impacts in situ stress prediction is an important and unresolved question. This work presents an enhancement of ML/DL-based workflow by training and implementing ML/DL models using equivalent saturated acoustic velocities (low-frequency) obtained by applying Biot–Gassmann fluid substitution on the ultrasonic velocities of dry cores. The models were trained on TUV data sets derived from three subsurface cores extracted from the geothermal well 16B(78)-32 at the Utah FORGE site. Each core was subjected to 75 unique stress configurations for velocity measurement in the dry state. The ML/DL trained on the TUV data set with equivalent saturated velocities demonstrated promising performance to predict in situ stress in subsurface geological rocks using velocity–stress relationships with R 2 of 0.86, 0.971, and 0.975 and root mean squared error (RMSE) of 2.59, 1.92, and 1.80 for validation/testing phases of vertical, minimum horizontal, and maximum horizontal stress models, respectively. Additionally, interpretation and explanation by Shapley additive explanations (SHAP) analysis further improved scientific validation and model reliability for estimating in situ stresses.

colloids↗
DOE OSTI2021

Spray Pyrolysis-Aerosol Deposition for the Production of Thick Yttria-Stabilized Zirconia Coatings

Aerosol deposition (AD) is a coating technique wherein particles are impacted onto a target substrate at reduced pressures, and supersonic particle impact velocities lead to coating consolidation. The limiting step in AD application is often not supersonic deposition operation, but aerosolization of powder particles with the proper size distribution; the translational impact velocity is strongly size-dependent. It is demonstrated that by directly synthesizing particles in the gas phase, size-controlled ceramic particles can be injected into AD systems. This in situ formation step obviates the need for particle aerosolization. Ultrasonic spray pyrolysis (USP) is applied to produce yttria-stabilized zirconia (YSZ), and USP is directly coupled with AD to produce consolidated, thick, YSZ coatings on metal substrates. USP-AD yields YSZ coatings on stainless steel and aluminum substrates with porosities <0.20, which grow to thicknesses beyond 100 μm. Aerodynamic particle spectrometry and electron microscopy reveal that the depositing particles are 200 nm–1.2 μm in diameter, though each particle is composed of nanocrystalline YSZ. Supporting computational fluid dynamics calculations demonstrate that the YSZ particle impact speeds are above 300 m s -1 . Thermal conductivity measurements demonstrate that USP-AD coatings have conductivities consistent with those produced from high-temperature processes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Proceedings from the State of the Science and Technology for Minimizing Impacts to Bats from Wind Energy

The U.S. Department of Energy Wind Energy Technologies Office (DOE WETO), and the National Renewable Energy Laboratory convened a workshop entitled the State of the Science and Technology for Minimizing Impacts to Bats from Wind Energy on 13–14 November 2019. The objectives of the workshop were to (1) Identify the current impact minimization measures that are, or can be, used to reduce bat fatalities at wind energy facilities, (2) Assess the current effectiveness of those minimization measures, (3) Identify and assess the research and development (R&D) opportunities needed to optimize and improve the effectiveness of current minimization and deterrent technologies and inform the development of future solutions; and (4) Identify potential emerging or novel methods for informing impact minimization measures at or around wind energy facilities. Specifically, the workshop focused on deterrent and curtailment strategies. For deterrents, the discussion centered on the existing technology (i.e., ultrasonic deterrents, dim-UV light, and texture coating), integration with wind turbines (either retrofitting or out of the box installation), effectiveness, validation studies, and cost (e.g., technology, installation, validation, and maintenance). For curtailment, the conversation was divided into blanket curtailment (i.e., based on time and wind speed) and smart curtailment (i.e., blanket curtailment plus additional variables such as temperature or bat activity). The workshop included plenary presentations, panels, and breakout sessions to share data and stakeholder perspectives, and engage participants. Although there are several priority topics related to bat and wind energy, this workshop focused the discussion on the current technologies and strategies that are, or can be, used to reduce bat fatalities at wind energy facilities, status of research and development (R&D) of minimization measures, opportunities to optimize costs and improve effectiveness, and potential emerging or novel approaches to explore. This workshop took a holistic approach and discussed all aspects associated with advancing deterrent technologies and curtailment strategies, including the technological, biological, economic, and regulatory barriers faced by the wind energy and wildlife community.

13 HYDRO ENERGY↗
NASA NTRS2003

Use of an Ultrasonic/Sonic Driller/Corer to Obtain Sample Powder for CHEMIN, a Combined XRD/XRF Instrument

A miniature CHEMIN XRD/XRF (X-Ray Diffraction/X-Ray Fluourescence) instrument is currently being developed for definitive mineralogic analysis of soils and rocks on Mars. One of the technical issues that must be addressed in order to enable XRD analysis on an extraterrestrial body is how best to obtain a representative sample powder for analysis. For XRD powder diffraction analyses, it is beneficial to have a fine-grained sample to reduce preferred orientation effects and to provide a statistically significant number of crystallites to the X-ray beam. Although a 2-dimensional detector as used in the CHEMIN instrument will produce good results with poorly prepared powders, the quality of the data will improve if the sample is fine-grained and randomly oriented. An Ultrasonic/Sonic Driller/Corer (USDC) currently being developed at JPL is an effective mechanism of sampling rock to produce cores and powdered cuttings. It requires low axial load (< 5N) and thus offers significant advantages for operation from lightweight platforms and in low gravity environments. The USDC is lightweight (<0.5kg), and can be driven at low power (<5W) using duty cycling. It consists of an actuator with a piezoelectric stack, ultrasonic horn, free-mass, and drill bit. The stack is driven with a 20 kHz AC voltage at resonance. The strain generated by the piezoelectric is amplified by the horn by a factor of up to 10 times the displacement amplitude. The tip impacts the free-mass and drives it into the drill bit in a hammering action. The free-mass rebounds to interact with the horn tip leading to a cyclic rebound at frequencies in the range of 60-1000 Hz. It does not require lubricants, drilling fluid or bit sharpening and it has the potential to operate at high and low temperatures using a suitable choice of piezoelectric material. To assess whether the powder from an ultrasonic drill would be adequate for analyses by an XRD/XRF spectrometer such as CHEMIN, powders obtained from the JPL ultrasonic drill were analyzed and the results were compared to carefully prepared powders obtained using a laboratory bench scale Retsch mill.

Chipera, S. J.↗
NASA NTRS1994

Assessment of impact damage of composite rocket motor cases

This contract reviewed the available literature on mechanisms of low velocity impact damage in filament wound rocket motor cases, MDE methods to quantify damage, critical coupon level test methods, manufacturing and material process variables and empirical and analytical modeling off impact damage. The critical design properties for rocket motor cases are biaxial hoop and axial tensile strength. Low velocity impact damage is insidious because it can create serious nonvisible damage at very low impact velocities. In thick rocket motor cases the prevalent low velocity impact damage is fiber fracture and matrix cracking adjacent to the front face. In contrast, low velocity loading of thin wall cylinders induces flexure, depending on span length and the flexure induces delamination and tensile cracking on the back face wall opposed to impact occurs due to flexural stresses imposed by impact loading. Important NDE methods for rocket motor cases are non-contacting methods that allow inspection from one side. Among these are vibrothermography, and pulse-echo methods based on acoustic-ultrasonic methods. High resolution techniques such as x-ray computed tomography appear to have merit for accurate geometrical characterization of local damage to support development of analytical models of micromechanics. The challenge of coupon level testing is to reproduce the biaxial stress state that the full scale article experiences, and to determine how to scale the composite structure to model full sized behavior. Biaxial tensile testing has been performed by uniaxially tensile loading internally pressurized cylinders. This is experimentally difficult due to gripping problems and pressure containment. Much prior work focused on uniaxial tensile testing of model filament wound cylinders. Interpretation of the results of some studies is complicated by the fact that the fabrication process did not duplicate full scale manufacturing. It is difficult to scale results from testing subscale cylinders since there are significant differences in out time of the resins relative to full scale cylinder fabrication, differences in hoop fiber tensioning and unsatisfactory coupon configurations. It appears that development of a new test method for subscale cylinders is merited. Damage tolerance may be improved by material optimization that uses fiber treatments and matrix modifications to control the fiber matrix interface bonding. It is difficult to develop process optimization in subscale cylinders without also modeling the longer out times resins experience in full scale testing. A major breakthrough in characterizing the effect of impact damage on residual strength, and understanding how to scale results of subscale evaluations, will be a sound micromechanical model that described progressive failure of the composite. Such models will utilize a three dimensional stress analysis due to the complex nature of low velocity impact stresses in thick composites. When these models are coupled with non-contact NDE methods that geometrically characterize the damage and acoustic methods that characterize the effective local elastic properties, accurate assessment of residual strength from impact damage may be possible. Directions for further development are suggested.

Paris, Henry G.↗
DOE OSTI2022

Carbon nanofibers (CNFs) dispersed in ultra-high performance concrete (UHPC): Mechanical property, workability and permeability investigation

This paper presents experimental data on the effect of carbon nano-fiber (CNF) dispersion on mechanical behavior, workability, and permeability of ultra-high-performance concrete containing CNF (UHPC-CNF). The addition of CNFs in concrete has been shown to provide improved performance. However, an inhomogeneous distribution of CNFs in the cement matrix can result in no impact or decreased mechanical performance. Due to the van der Waal's forces and hydrophobic surface properties of the CNFs, good dispersion in mix fluids and cement paste is challenging. Experimental studies of UHPC-CNF with different dispersion methods are provided. Further mixing with optimized UHPC paste allowed for the investigation of the optimal dosage of CNFs, impact on porosity, compressive strength, flexural strength, hydration rate, and slump. Scanning electron microscopy (SEM) analysis visually revealed the effect of dispersion. Our results indicate that shear mixing and subsequent ultrasonic dispersion with chemical surfactants can provide a well-dispersion liquid admixture of CNFs resulting in high mechanical performance of UHPC-CNFs composites. The water permeability and chloride resistance of optimized UHPC-CNFs composites were further evaluated with the wicking test and ponding test to reveal improved performance for these properties as well.

36 MATERIALS SCIENCE↗
NASA NTRS2015

Free-Mass and Interface Configurations of Hammering Mechanisms

The design of the free-mass in an ultrasonic driller/corer (USDC) has been refined in order to improve the performance and operational reliability of the system. In one embodiment, the improvements in performance and operational reliability include decreasing the impact surface area of the free-mass to increase the transfer of impact energy from the piezoelectric transducer and reductions in the likelihood that the system will jam.

Bao, Xiaoqi↗
NASA NTRS2023

Characterization of Low-Velocity Impact Damage in Thermoplastic Laminated Composites

The impact damage response of two thermoplastic material systems were compared over a range of impact energies. Eight-inch-square impact specimens with a 24-ply quasi-isotropic layup were manufactured from TC1225 LMPAEK T700G from Toray Industries and APC AS4D/PEKK-FC from Solvay. The effect of the degree of crystallinity (DOC) on the damage response was also investigated using a third set of specimens from the Toray material manufactured with reduced crystallinity. Using a combination of data obtained from X-ray computed tomography (CT) scans and ultrasonic testing (UT), detailed damage maps were created for every interface and ply for selected specimens. Using these damage maps, the delamination size, shape, and area were evaluated at each interface. The presence of fractured fibers was also identified on each ply. The LMPAEK material was found to have fewer and smaller delaminations than the PEKK specimens for impacts at the same energy. However, the LMPAEK specimens contained a larger number of fiber breaks. A similar trend was observed when comparing the baseline LMPAEK specimens with the low-crystallinity LMPAEK specimens. The low-crystallinity specimens had very little delamination but had a large number of plies with fiber breaks. In addition, the LMPAEK specimens often contained lines of fiber fractures in near-surface plies emanating from the contact region that were not present in the PEKK specimens.

Composite Materials↗