Search NASA⌕ Search

SEARCH · Search NASA

Results for “void formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Amphiphilic nanopores that condense undersaturated water vapor and exude water droplets

Condensation of water vapor in confined geometries, known as capillary condensation, is a fundamental phenomenon with far-reaching implications. While hydrophilic pores enable liquid formation from undersaturated vapor without energy input, the condensate typically remains confined, limiting practical utility. Here, we explore the use of amphiphilic nanoporous polymer-infiltrated nanoparticle films that condense and release liquid water under isothermal and undersaturated conditions. By tuning the polymer fraction and nanoparticle size, we optimize condensation and droplet formation. As vapor pressure increases, voids fill with condensate, which subsequently exudes onto the surface as microscopic droplets. This behavior, enabled by a balance of polymer hydrophobicity and capillarity, reveals how amphiphilic nanostructures can drive accessible water collection. Our findings provide design insights for materials supporting energy-efficient water harvesting and heat management without external input.

Science & Technology - Other Topics↗
DOE OSTI2023

A novel approach for adaptive skeleton toolpath generation

Industry 4.0 is revolutionizing manufacturing through the integration of automation and real-time data sharing in cyber-physical systems. At the forefront of this revolution is large-format additive manufacturing. In large-format printing, parts are often designed to be an even number of beads wide to produce a completely dense part. However, voids can still arise. This is often due to the part not being an even number of bead widths wide in some areas, or in geometry containing acute angles, as the process of generating closed contours cannot completely fill the space. Voids can be tolerated in smaller models, but in large-format additive manufacturing they may cause mechanical defects. To fill these voids, open loop paths called skeletons are often used, but they are typically limited by the physical constraints defined in the slicing software. To address this, researchers at Oak Ridge National Laboratory have extended skeleton toolpaths via an adaptive methodology. These adaptive skeletons were found to better fill void spaces through manipulation of physical parameters of the build process and were calculated as part of the slicing process.

42 ENGINEERING↗
DOE OSTI2019

Multimodality imaging of the male urethra: trauma, infection, neoplasm, and common surgical repairs

Objective: The aim of this article is to describe the indications and proper technique for RUG and MRI, their respective image findings in various disease states, and the common surgical techniques and imaging strategies employed for stricture correction. Results: Because of its length and passage through numerous anatomic structures, the adult male urethra can undergo a wide array of acquired maladies, including traumatic injury, infection, and neoplasm. For the urologist, imaging plays a crucial role in the diagnosis of these conditions, as well as complications such as stricture and fistula formation. While retrograde urethrography (RUG) and voiding cystourethrography (VCUG) have traditionally been the cornerstone of urethral imaging, MRI has become a useful adjunct particularly for the staging of suspected urethral neoplasm, visualization of complex posterior urethral fistulas, and problem solving for indeterminate findings at RUG. Conclusions: Familiarity with common urethral pathology, as well as its appearance on conventional urethrography and MRI, is crucial for the radiologist in order to guide the treating urologist in patient management.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2022

Crystal structure of a trigonal polymorph of aquadioxidobis(pentane-2,4-dionato-κ 2 O , O ′)uranium(VI)

The title compound, [UO 2 (acac) 2 (H 2 O)] consists of a uranyl(VI) unit ([O=U=O] 2+ ) coordinated to two monoanionic acetylacetonate (acac, C 5 H 7 O 2 ) ligands and one water molecule. The asymmetric unit includes a one-half of a uranium atom, one oxido ion, one-half of a water molecule and one acac ligand. The coordination about the uranium atom is distorted pentagonal–bipyramidal. The acac ligands and O w atom comprise the equatorial plane, while the uranyl O atoms occupy the axial positions. Intermolecular hydrogen bonding between complexes results in the formation of two-dimensional hexagonal void channels along the c- axis direction with a diameter of 6.7 Å. The monoclinic ( P 2 1 / c space group) polymorph was reported by Alcock & Flanders [(1987). Acta Cryst. C 43 , 1480–1483].

Hernandez, Alejandro↗
DOE OSTI2022

Enhanced terrestrial Fe(II) mobilization identified through a novel mechanism of microbially driven cave formation in Fe(III)-rich rocks

Most cave formation requires mass separation from a host rock in a process that operates outward from permeable pathways to create the cave void. Given the poor solubility of Fe(III) phases, such processes are insufficient to account for the significant iron formation caves (IFCs) seen in Brazilian banded iron formations (BIF) and associated rock. Here in this study we demonstrate that microbially-mediated reductive Fe(III) dissolution is solubilizing the poorly soluble Fe(III) phases to soluble Fe(II) in the anoxic zone behind cave walls. The resultant Fe(III)-depleted material (termed sub muros) is unable to maintain the structural integrity of the walls and repeated rounds of wall collapse lead to formation of the cave void in an active, measurable process. This mechanism may move significant quantities of Fe(II) into ground water and may help to explain the mechanism of BIF dissolution and REE enrichment in the generation of canga. The role of Fe(III) reducing microorganism and mass separation behind the walls (outward-in, rather than inward-out) is not only a novel mechanism of speleogenesis, but it also may identify a previously overlooked source of continental Fe that may have contributed to Archaean BIF formation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

In situ measurements of non-equilibrium positron state defects during He irradiation in Si

Radiation-induced property changes in materials originate from the energy transfer from an incoming particle to the existing lattice, displacing atoms. The displaced atoms can cause the formation of extended defects including dislocation loops, voids, or precipitates. The non-equilibrium defects created during damage events determine the extent of these larger defects and are a function of dose rate, material, and temperature. However, these defects are transient and can only be probed indirectly. Herein, we present direct experimental measurements and evidence of irradiated non-equilibrium vacancy formation, where in situ positron annihilation spectroscopy was used to prove the generation of non-equilibrium defects in silicon.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural evolution and transmutation in tungsten under ion and neutron irradiation

This study aims to compare the effects of neutron and self-ion irradiation on the mechanical properties and microstructural evolution in W. Neutron irradiation at the HFR reactor to 1.67 dpa at 800 °C resulted in the formation of large Re and Os rich clusters and voids. The post-irradiation composition was measured using APT and verfified against FISPACT modelling. The measured Re and Os concentration was used to create alloys with equivalent concentrations of Re and Os. These alloys were exposed to self-ion irradiation to a peak dose of 1.7 dpa at 800 °C. APT showed that self-ion irradiation leads to the formation of small Os clusters, wheras under neutron irradiation large Re/Os clusters form. Voids are formed by both ion and neutron irradiation, but the voids formed by neutron irradiation are larger. By comparing the behaviour of W-1.4Re and W-1.4Re-0.1Os, suppression of Re cluster formation was observed. Irradiation hardening was measured using nanoindentation and was found to be 2.7 GPa, after neutron irradiation and 1.6 GPa and 0.6 GPa for the self-ion irradiated W-1.4Re and W-1.4Re-0.1Os. The higher hardening is attributed to the barrier strength of large voids and Re/Os clusters that are observed after neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Impact of Void-finding Algorithms on Galaxy Classification

We explore how the definition of a void influences the conclusions drawn about the impact of the void environment on galactic properties using two void-finding algorithms in the Void Analysis Software Toolkit: Voronoi Voids (V 2 ), a Python implementation of ZOnes Bordering On Voidness (ZOBOV); and VoidFinder, an algorithm that grows and merges spherical void regions. Using the Sloan Digital Sky Survey Data Release 7, we find that galaxies found in VoidFinder voids tend to be bluer and fainter and to have higher (specific) star formation rates than galaxies in denser regions. Conversely, galaxies found in V 2 voids show less significant differences when compared to galaxies in denser regions, less consistent with the large-scale environmental effects on galaxy properties expected from both simulations and previous observations. These results align with previous simulation results that show V 2 -identified voids “leak” into the dense walls between voids because their boundaries extend up to the density maxima in the walls. As a result, when using ZOBOV-based void-finders, galaxies likely to be part of wall regions are instead classified as void galaxies, a misclassification that can be critical to our understanding of galaxy evolution.

cosmic web↗
DOE OSTI2024

Effect of Carbon on Void Nucleation in Iron

The study reports the significance of carbon presence in affecting void nucleation in Fe. Without carbon, void nucleation rates decrease gradually at high temperatures but remain significantly high and almost saturated at low temperatures. With carbon present, even at 1 atomic parts per million, void nucleation rates show a low-temperature cutoff. With higher carbon levels, the nucleation temperature window becomes narrower, the maximum nucleation rate becomes lower, and the temperature of maximum void nucleation shifts to a higher temperature. Fundamentally, this is caused by the change in effective vacancy diffusivity due to the formation of carbon-vacancy complexes. The high sensitivity of void nucleation to carbon comes from the high sensitivity of void nucleation to the vacancy arrival rate in a void. The void nucleation is calculated by first obtaining the effective vacancy diffusivity considering the carbon effect, then calculating the defect concentration and defect flux change considering both carbon effects and pre-existing dislocations, and finally calculating the void nucleation rate based on the recently corrected homogeneous void nucleation theory. The study is important not only in the fundamental understanding of impurity effects in ion/neutron irradiation but also in alloy engineering for judiciously introducing impurities to increase swelling resistance, as well as in the development of simulation and modeling methodologies applicable to other metals.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Infrared Optical Constants from Pressed Pellets of Powders: I. Improved n and k Values of (NH4)(2)SO(4)from Single-Angle Reflectance

In combination with other parameters, the real, n(?), and imaginary, k(?), components of the complex refractive index, = n + ik, can be used to simulate the optical properties of a material in different forms, e.g. its infrared spectra. But obtaining reliable values of the optical constants n/k for solid materials is challenging due to the lack of optical quality specimens, usually crystals, large enough to measure. An alternative to crystals is to press the powder into a uniform disk. We have produced pellets from ammonium sulfate, (NH4)2SO4, powder and derived the pellets’ n and k values via single-angle reflectance using a specular reflectance device in combination with a Fourier transform infrared spectrometer. The single-angle technique measures amplitude of light reflected from the material as a function of wavelength over a wide spectral domain; the optical constants are determined from the reflectance data using the Kramers-Kronig relationship. We investigate several parameters associated with the pellets and pellet formation and their effects upon delivering the most reliable n/k values. Parameters studied include pellet diameter, mass and density (void space), drying, grinding, sieving and particle size in the pellet formation, as well as pressing pressure and duration. Of these parameters, using size-selected mixtures of dried, small (< 100 µm) particles and pressing at = 10 tons for at least 30 minutes were found key to forming highly reflective samples. Comparison to two sets of previous literature n(?) and k(?) values obtained from crystalline (NH4)2SO4 both as crystal reflectance as well as extinction spectra of aerosols measured in a flow tube show reasonable agreement, but suggests the present values, as confirmed from two independent techniques, represent a substantial improvement for n/k values for (NH4)2SO4, also demonstrating promise to measure the optical constants of other materials.

Optical constants, index of refraction, single-ang↗
DOE OSTI2024

Evaluating Pressure‐dependent Discharge Behavior of Foil Versus In situ Plated Lithium Metal Anodes in Solid‐State Batteries

Abstract Anode‐free manufacturing of solid‐state batteries (SSBs) shows promise to maximize energy density by eliminating excess lithium (Li) and simplifying battery production. However, high reversibility during discharge (stripping of Li) is necessary for long‐lifetime SSBs with a limited Li reservoir. Further, the plastic flow of Li changes depending on the Li thickness, leading to possible differences in discharge performance under stack pressure. This work investigates the pressure‐dependent discharge performance of anode‐free manufactured SSBs with in situ plated Li and compares the performance to that of conventional thick Li foil cells. Distinct stripping behavior is observed at low pressures (0–1 MPa), where Li diffusivity and initial interfacial contact may control accessible capacity, compared to high pressures (3–10 MPa) where mechanical deformation of Li likely governs stripping behavior. Analysis of impedance spectra collected during stripping shows that additional stack pressure delays the formation of deep, as opposed to lateral, voids in the Li anode. These results provide insights to guide the transition from thick Li foil anodes to anode‐free manufactured SSBs.

Haslam, Catherine G.↗
DOE OSTI2023

Graded microstructure and mechanical properties of spark plasma sintered Fe-Cr alloys

Developing graded microstructure and mechanical properties is critical for accelerating the design and optimization of structural materials for a wide range of applications. Here, in this study, Fe-Cr alloys were fabricated by spark plasma sintering (SPS) technique. The microstructure, microhardness, and tensile properties of the as-fabricated and thermally annealed variants were investigated. Graded grain structures were created in the as-fabricated cylinders along both axial and radial directions. Grain size was gradually reduced from the sample periphery to the center. Microhardness measurements reveal a gradual decrease of hardness towards the periphery of the samples. The as-fabricated Fe-Cr alloys show a desired combination of tensile strength and elongation, primarily due to the formation of a high density of oxides, voids, dislocations, and grain boundaries. After in-situ thermal annealing at 600 °C under 60 MPa for 2 h using SPS, the Fe-Cr alloys underwent minimal grain growth, and the graded grain structures were retained. The hardness was more uniformly distributed in the annealed variants, and the tensile strength was reduced with an increase in the total elongation, which is attributed to the dissolution of nano-sized oxide particles and the relief of the residual stress. This study demonstrates that SPS coupled with subsequent heat treatment can tailor the graded microstructure and control the mechanical properties of Fe-Cr alloys, showing potential applications in other alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Local and large-scale effects on the astrophysics of void galaxies

ABSTRACT Galaxies in cosmic voids have been reported with properties related to a delayed evolution compared to the rest of the Universe. These characteristics reflect the interaction of galaxies with the environment. However, it is not clear the degree of influence of the large-scale structure on the properties of void galaxies or if these are only influenced by the low local density around them typical of these regions. In this article, we identified cosmic voids in the SDSS-DR16 and studied the g–r colour, star formation rate, and concentration of galaxies. We identified galaxy groups to characterize the local environment and studied the properties of galaxies as a function of total and stellar masses, separately analysing those in voids and the general sample. Our results show that galaxies that inhabit haloes of a given mass (below ${\sim}10^{13.5}{\rm M}_{\odot }$), are bluer, have a higher star formation rate and are less concentrated when the host halo is inside voids compared to other regions. For larger halo masses, the trend disappears. We also analyse whether the properties of galaxies are sensitive to the type of voids that inhabit. This is done by separating voids embedded in overdense regions (S-type) from those that asymptotically converge to the average density of the Universe (R-type). We found that galaxies in R-type voids are bluer, with higher SFR and less concentration than in S-type voids. Our results indicate some degree of correlation of galaxy properties with the large-scale environment provided by voids, suggesting possible second-order mechanisms in galaxy evolution.

Astronomy & Astrophysics↗
DOE OSTI2022

Weldability of irradiated Stainless Steel 304 materials harvested from the National Research Universal (NRU) reactor

In this work, the weldability of the neutron-irradiated Stainless Steel 304 (SS 304) materials containing estimated helium levels of 12 to 44 appm has been studied through a Collaborative Research and Development Agreement between the Canadian Nuclear Laboratories and Oak Ridge National Laboratory. The work utilizes a SS 304 component harvested from the National Research Universal reactor. Laser beam welding was used to explore suitable welding conditions and associated parameters, to determine helium concentration limits for successful welding of irradiated stainless-steels. The experimental results show that maximum fusion zone void sizes, fusion zone void quantity and total heat affected zone helium-induced crack length generally increased with increasing He levels and effective weld heat input. A proper combination of welding parameters with low effective heat input, such as, laser power, weld travel speed and wire feed speed, were shown to improve the welding quality, and potentially reduce the length and probability of the formation of grain boundary helium-induced cracking and voids of irradiated SS 304 even with He concentrations as high as about 44 appm.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Probing Microstructure-induced Swelling & Thermal Property Changes in Ion-Irradiated Oxide Fuels using Laser-generated Surface Acoustic Waves

Radiation of fuel rods with neutrons during a fission reaction in a nuclear reactor is known to affect the material microstructure of the fuel as a result of fission fragment damage, and lead to the formation of atomic-level defects such as voids, dislocation loops, and lattice swelling from fission-gas release. A consequence of the radiation-induced damage in nuclear fuels is the drastic alteration of material properties, in particular, the reduction of the thermal conductivity – a key parameter that governs the transport of thermal energy released from fissile fuel atoms to the surrounding coolant. Swelling can induce high stresses and ultimate failure of the cladding. A fundamental understanding of the role of radiation-induced damage on the thermal transport and mechanical properties of nuclear fuels is therefore critical for efficient, reliable and safe operation of a nuclear power plant. As opposed to conventional post-irradiation examination techniques that are often time-consuming and require significant sample preparation, laser-based characterization methods have emerged as promising non-contact, non-destructive tools to measure the evolution of microstructure-induced material property changes. Moreover, laser methods offer the promise of in-situ characterization while the material is being irradiated. This project aims to develop an improved understanding of the impact of radiation-induced changes to material microstructure on the thermal and elastic properties of nuclear materials. A laser ultrasonic technique, known as the transient grating (TG) spectroscopy method, is used to simultaneously measure thermal diffusivity and elastic properties in unirradiated and ion-irradiated oxide nuclear fuel samples. The results will complement on-going investigations on electron- and phonon-mediated thermal transport in nuclear materials and will provide foundational work for incorporating the influence of defects in fuel performance codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Coupled phase field damage and crystal plasticity analysis of intragranular fracture: The role of crystallographic orientation and voids

Damage evolution in engineering metal alloys at the grain scale exhibits significant microstructural heterogeneity and anisotropy. These heterogeneities create local hotspots for stress and strain localization, leading to void nucleation. Crystal orientation influences the active slip systems around voids, affecting lattice rotation and potentially forming discontinuities. At low triaxiality, voids may change shape due to lower stress, rotation, elongation, and coalescence. At high triaxiality, the correlation between crystal orientation and void growth rate becomes stronger, resembling the behavior observed in isolated single crystals. Therefore, understanding the effects of crystal orientation, heterogeneous strain, and defect evolution is crucial for single crystal fracture characterization. Here, in this work, a coupled phase-field damage (PFD) and crystal plasticity (CP) model is implemented within a finite element framework to analyze crystal deformation and failure. The CP method employs a dislocation density-based constitutive model, while intragranular failure is modeled using an anisotropic PFD method. The PFD model considers both the stored energy due to elastic stretching and the energy release due to defect formation and crack formation. A single crystal Al2219 with an intracrystalline spherical void is chosen to analyze fracture. The study finds that fracture propagation is strongly correlated with crystal orientations. This coupled CP-PFD model provides accurate failure prediction in crystalline materials by incorporating the effects of crystal orientations and existing voids. This study demonstrates how the local microstructure and defects influence plastic deformation and failure mechanisms in metal alloys.

Aluminum alloy↗
DOE OSTI2020

Enhanced flow boiling heat transfer on chromium coated zircaloy-4 using cold spray technique for accident tolerant fuel (ATF) materials

Flow boiling heat transfer tests were conducted to evaluate the Critical Heat Flux (CHF) and Heat Transfer Coefficient (HTC) of conventional and accident tolerant fuel (ATF) cladding materials, i.e., bare Zircaloy-4 (Zr4), and Zircaloy-4 coated with Chromium using physical vapor deposition (PVD) (Zr4-Cr-PVD) and cold spray process (Zr4-Cr-CS), respectively. The tests were performed on a single heater rod with a uniform heat flux profile, at the atmospheric pressure, inlet temperature (24 °C) and mass flow rate (750 kg/m 2 s). HTC’s were increased by 5.2% and 3.3% on Zr4-Cr-CS compared to bare Zr4 and Zr4-Cr-PVD. Improved HTCwas attributed to the increased void fraction and high roughness (Ra = 532 nm) of the Zr4-Cr-CS. In detail, the micro-cavities, which act as bubble seeds, were entirely distributed on the Zr4-Cr-CS, and these micro-cavities generated smaller and faster bubbles, thus the void fraction increased by 10.9% compared to bare Zr4. HTC is improved by these smaller and faster bubbles which can remove heat from the heater rod surface more efficiently. To identify the exact location of CHF, the surface temperature profile was measured using advanced fiber-optic sensors which have high temporal/spatial resolution (distance between point to point: ~2.5 mm, frequency ~100 Hz). CHF occurred at 80–95% along the heated length and showed an 11.6% reduction on Zr4-Cr-CS compared to bare Zr4. We hypothesize the CHF reduction was caused by the lower wettability of the Zr4-Cr-CS which reduces the liquid supply to the surface, and vigorous bubble accumulation owing to high void fraction near the outlet, which results in early formation of the vapor film. During the post-CHF quenching phase, the rougher Zr4-Cr-CS showed larger cooling rates compared to the bare Zr4 and Zr4-Cr-PVD, preventing of oxidation by chromium layer. In conclusion, we demonstrate that the high roughness on the Zr4-Cr-CS increased the number of micro-cavities on the surface, resulting in 5.2% increase in HTC and improvement in the quenching heat transfer performance whereas CHF was 11.6% reduced compared to bare Zr4. Overall statistically there is little effect in the coating with regards to CHF and slight improvement in HTC.

42 ENGINEERING↗
DOE OSTI2021

Comparison of void swelling of ferritic-martensitic and ferritic HT9 alloys after high-dose self-ion irradiation

In this work, ferritic-martensitic (F/M) HT9 along with fully ferritic HT9 specimens were irradiated using self-ions to 600 peak displacement-per-atom (dpa) at 450 °C. To investigate and minimize the carbon contamination effect on void swelling, two identical F/M HT9 specimens were prepared: one without a coating and the other one with a tungsten and silver coating on the surface prior to irradiation. The specimen without a coating showed carbide formation in the matrix, resulting from carbon contamination during irradiation, with no voids observed. The coated sample did not form matrix carbides, and voids were observed within the irradiated region. The same coating was applied to the ferritic HT9, and void swelling results of both the F/M HT9 and the ferritic HT9 alloys were compared after irradiation. The F/M HT9 exhibited a maximum of 2.6% swelling, while the ferritic HT9 showed a maximum of 0.8% swelling at a 400–500 nm depth, equivalent to 334 local dpa. The results were correlated with the instability of carbides in the ferritic HT9 under irradiation. Carbides in the F/M HT9 and the ferritic HT9 are both M23C6, but the matrix carbides in the ferritic HT9 were less stable under the irradiation, compared to the ones on the grain boundaries in the F/M HT9. The study shows the impact of chemistry on the void swelling which overpowers the microstructural factors such as grain size and phase.

36 MATERIALS SCIENCE↗