A thick-walled viscoelastic model for the mechanics of arteries
Arterial model with effects of thick walls, linear viscoelasticity and wall tethering for studying arterial mechanics
Kuchar, N. R.↗
SEARCH · Search NASA
Results for “wall modeling”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
DNS and modeling of the interaction between turbulent premixed flames and walls
The interaction between turbulent premixed flames and walls is studied using a two-dimensional full Navier-Stokes solver with simple chemistry. The effects of wall distance on the local and global flame structure are investigated. Quenching distances and maximum wall heat fluxes during quenching are computed in laminar cases and are found to be comparable to experimental and analytical results. For turbulent cases, it is shown that quenching distances and maximum heat fluxes remain of the same order as for laminar flames. Based on simulation results, a 'law-of-the-wall' model is derived to describe the interaction between a turbulent premixed flame and a wall. This model is constructed to provide reasonable behavior of flame surface density near a wall under the assumption that flame-wall interaction takes place at scales smaller than the computational mesh. It can be implemented in conjunction with any of several recent flamelet models based on a modeled surface density equation, with no additional constraints on mesh size or time step.
Poinsot, T. J.↗
Transient liquid-crystal technique used to produce high-resolution convective heat-transfer-coefficient maps
In this transient technique the preheated isothermal model wall simulates the classic one-dimensional, semi-infinite wall heat transfer conduction problem. By knowing the temperature of the air flowing through the model, the initial temperature of the model wall, and the surface cooling rate measured at any location with time (using the fast-response liquid-crystal patterns recorded on video tape), the heat transfer coefficient can be calculated for the color isothermal pattern produced. Although the test was run transiently, the heat transfer coefficients are for the steady-state case. The upstream thermal boundary condition was considered to be isothermal. This transient liquid-crystal heat-transfer technique was used in a transient air tunnel in which a square-inlet, 3-to-1 exit transition duct was placed. The duct was preheated prior to allowing room temperature air to be suddenly drawn through it. The resulting isothermal contours on the duct surfaces were revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record was made of the temperature and time data for all points on the duct surfaces during each test. The duct surfaces were uniformly heated using two heating systems: the first was an automatic temperature-controlled heater blanket completely surrounding the test duct like an oven, and the second was an internal hot-air loop through the inside of the test duct. The hot-air loop path was confined inside the test duct by insulated heat dams located at the inlet and exit ends of the test duct. A recirculating fan moved hot air into the duct inlet, through the duct, out of the duct exit, through the oven, and back to the duct inlet. The temperature nonuniformity of the test duct model wall was held very small. Test results are reported for two inlet Reynolds numbers of 200,000 and 1,150,000 (based on the square-inlet hydraulic diameter) and two free-stream turbulence intensities of about 1 percent, which is typical of wind tunnels, and up to 20 percent (using a grid), which is typical of real engine conditions.
Hippensteele, Steven A.↗
Adaptation of two-dimensional transonic analysis code, TSFOIL, for use in modeling adaptive wall test sections
The effects of the elastic deformation of the wind tunnel wall held to a streamline-like shape were simulated numerically. The wall itself is simulated by a finite element model and is allowed to deform under the pressure loading developing in the wind tunnel with an airfoil model present. A modified version of the transonic analysis program, TSFOIL, is then used to determine the resulting flow field with the effects of the deformed wall included, the shape of the wall and the flow field. Once a result from a particular operating condition was obtained, the pressure distribution on the airfoil in the wind tunnel model is compared with solutions generated by TSFOIL in the free air mode.
Webb, J.↗
Analysis of radiative and phase-change phenomena with application to space-based thermal energy storage
The simplified geometry for the analysis is an infinite, axis symmetric annulus with a specified solar flux at the outer radius. The inner radius is either adiabatic (modeling Flight Experiment conditions), or convective (modeling Solar Dynamic conditions). Liquid LiF either contacts the outer wall (modeling ground based testing), or faces a void gap at the outer wall (modeling possible space based conditions). The analysis is presented in three parts: Part 3 considers and adiabatic inner wall and linearized radiation equations; part 2 adds effects of convection at the inner wall; and part 1 includes the effect of the void gap, as well as previous effects, and develops the radiation model further. The main results are the differences in melting behavior which can occur between ground based 1 g experiments and the microgravity flight experiments. Under 1 gravity, melted PCM will always contact the outer wall having the heat flux source, thus providing conductance from this source to the phase change front. In space based tests where a void gap may likely form during solidification, the situation is reversed; radiation is now the only mode of heat transfer and the majority of melting takes place from the inner wall.
Lund, Kurt O.↗
A Phenomenological Thermal Spray Wall Interaction Modeling Framework Applied to a High Temperature Ignition Assistant Device
Airborne compression ignition engines must operate with reliable ignition systems to achieve proper ignition at every cycle, particularly at high altitudes. Glow-plug-based ignition-assistant (IA) devices can provide the necessary energy to preheat the fuel and ensure ignitability of the fuel-air mixture. Ignitability of liquid sprays can be facilitated via direct impingement onto the hot IA surface, however this comes with adverse effects on the IA durability. Therefore, optimizing an IA’s design requires detailed understanding of the physics of fuel spray impingement of superheated surfaces. While spray impingement on relatively low wall temperatures has been extensively studied and appropriate numerical models have been proposed through the years, fundamental understanding of high-speed liquid spray impingement on superheated walls is still elusive. This work aims to formulate a phenomenological thermal spray-wall interaction framework for modeling the film-boiling-induced heat transfer, atomization, and dispersion of fuel spray droplets impinging onto a superheated IA device. A qualitative comparison of the new phenomenological model is performed against optical experiments from the literature of an F-24 fuel spray injected onto an IA device located 12 mm away from the injector tip. The temperature of the IA was set at 1400 K. The fuel injection pressure was 400 bar, while the ambient gas pressure and temperature were 30 bar and 800 K, respectively. The performance of the phenomenological model is evaluated in comparison with two other state-of-art models from the literature. A qualitative analysis of the different spray and fuel-air mixture characteristics is performed to outline the differences in the predictions offered by the new phenomenological model and the two state-of-art spray-wall interaction models.
droplet dispersion↗
One-equation near-wall turbulence modeling with the aid of direct simulation data
The length scales appearing in the relations for the eddy viscosity and dissipation rate in one-equation models were evaluated from direct numerical simulation data for developed channel and boundary-layer flow at two Reynolds numbers each. To prepare the ground for the evaluation, the distribution of the most relevant mean-flow and turbulence quantities is presented and discussed with respect to Reynolds-number influence and to differences between channel and boundary-layer flow. An alternative model is also examined in which bar-(v'(exp 2))(exp 1/2) is used as velocity scale instead of k(exp 1/2). With this velocity scale, the length scales now appearing in the model follow very closely a linear relationship near the wall so that no damping is necessary. For the determination of bar-v'(exp 2) in the context of a one-equation model, a correlation is provided between bar-(v'(exp 2))/k and bar-(u'v')/k.
Rodi, W.↗
Wall layer models for the calculation of velocity and heat transfer in turbulent boundary layers
In the computation of turbulent boundary-layer flows and internal flows, a substantial amount of mesh points and computational effort is required to adequately resolve the intense temperature and velocity profile variations in the near wall region. In this study, analytical profile approximations are obtained for the mean velocity and temperature distribution in the wall layer; these profiles are based upon consideration of the observed coherent structure of the time-dependent wall-layer flow. The profile approximations are relatively simple analytical formulae which satisfy all the required compatibility conditions at the wall and the logarithmic behavior at the edge of the wall layer. The Reynolds analogy for heat transfer is not used in the present theory. A general method for utilizing the present wall-layer profile models in a prediction method is indicated.
Walker, J. D. A.↗
Modelling Unsteady Wall Pressures Beneath Turbulent Boundary Layers
As a structural entity of turbulence, hairpin vortices are believed to play a major role in developing and sustaining the turbulence process in the near wall region of turbulent boundary layers and may be regarded as the simplest conceptual model that can account for the essential features of the wall pressure fluctuations. In this work we focus on fully developed typical hairpin vortices and estimate the associated surface pressure distributions and their corresponding spectra. On the basis of the attached eddy model, we develop a representation of the overall surface pressure spectra in terms of the eddy size distribution. Instantaneous wavenumber spectra and spatial correlations are readily derivable from this representation. The model is validated by comparison of predicted wavenumber spectra and cross-correlations with existing emperical models and experimental data.
Ahn, B-K.↗
Multiblock analysis for Shuttle Orbiter reentry heating from Mach 24 to Mach 12
A multiblock, laminar heating analysis for the shuttle orbiter at three trajectory points ranging from Mach 24.3 to Mach 12.86 on reentry is described. The analysis is performed using the Langley Aerothermodynamic Upwind Relaxation Algorithm with a seven species chemical nonequilibrium model. A finite-catalytic-wall model appropriate for shuttle tiles at a radiative equilibrium wall temperature is applied. Computed heating levels are generally in good agreement with the flight data, although a few rather large discrepancies remain unexplained. The multiblock relaxation strategy partitions the flowfield into manageable blocks requiring a fraction of the computational resources (time and memory) required by a full domain approach. In fact, the computational cost for a solution at even a single trajectory point would be prohibitively expensive at the given resolution without the multiblock approach. Converged blocks are reassembled to enable a fully coupled converged solution over the entire vehicle, starting from a nearly converged initial condition.
LANGLEY AEROTHERMODYNAMIC UPWI↗
Turbulence Simulations of Transonic Flows over an NACA-0012 Airfoil
Three different simulation approaches, namely unsteady Reynolds-averaged Navier-Stokes (URANS), delayed detached-eddy simulation (DDES), and wall-modeled large-eddy simulation (WMLES) are employed to simulate transonic flow over an NACA-0012 airfoil at different angles of attack covering pre- and post-buffet-onset regimes. The freestream Mach number is 0.75, and the Reynolds number based on the chord length is 10 million. These conditions are the same as the wind-tunnel experimental conditions of McDevitt and Okuno (1985). The NASA FUN3D solver is used for the simulations, which is an unstructured, compressible flow solver. The URANS simulations are performed using the Spalart-Allmaras (SA) model with the compressibility correction, the DDES predictions are based on the SA model, and the WMLES are performed using an equilibrium wall-model. The unsteady RANS simulations, only with the compressibility correction, predict the pre- and post- buffet characteristics, which compare well with the experimental results. DDES results predicted a lower buffet onset angle compared to experiment. The predicted shock locations are upstream of the locations predicted by URANS. Using a fine grid in the spanwise direction, WMLES predictions show buffeting consistent with the experiment.
Transonic Buffet↗
Turbulence Simulations of Transonic Flows over an NACA-0012 Airfoil
Three different simulation approaches, namely unsteady Reynolds-averaged Navier-Stokes (URANS), delayed detached-eddy simulation (DDES), and wall-modeled large-eddy simulation (WMLES) are employed to simulate transonic flow over an NACA-0012 airfoil at different angles of attack covering pre-and post-buffet-onset regimes. The freestream Mach number is 0.75,and the Reynolds number based on the chord length is 10million. These conditions are the same as the wind-tunnel experimental conditions of McDevitt and Okuno (1985). The NASA FUN3D solver is used for the simulations, which is an unstructured, compressible flow solver. The URANS simulations are performed using the Spalart-Allmaras (SA) model with the compressibility correction, the DDES predictions are based on the SA model, and the WMLES are performed using an equilibrium wall-model. The unsteady RANS simulations, only with the compressibility correction, predict the pre-and post-buffet characteristics, which compare well with the experimental results. DDES results predicted a lower buffet onset angle compared to experiment. The predicted shock locations are upstream of the locations predicted by URANS. Using a fine grid in the span wise direction, WMLES predictions show buffeting consistent with the experiment.
Transonic Buffet↗
Turbulence Simulations of Transonic Flows over NACA-0012 and OAT15A Airfoils
Three different simulation approaches, namely unsteady Reynolds-averaged Navier-Stokes (URANS), delayed detached-eddy simulation (DDES), and wall-modeled large-eddy simulation (WMLES) are employed to simulate transonic flow over an NACA-0012, OAT15A airfoils at different angles of attack covering pre- and post-buffet-onset regimes. The freestream Mach number is 0.75, and the Reynolds number based on the chord length is 10 and 3million, respectively. The NASA FUN3D solver is used for the simulations, which is an unstructured, compressible flow solver. The URANS simulations are performed using the Spalart-Allmaras (SA) model with the compressibility correction, the DDES predictions are based on the SA model, and the WMLES are performed using an equilibrium wall-model. The unsteady RANS simulations, only with the compressibility correction, predict the pre- and post- buffet characteristics, which compare well with the experimental results. DDES results predicted a lower buffet onset angle compared to experiment. The predicted shock locations are upstream of the locations predicted by URANS. Using a fine grid in the spanwise direction, WMLES predictions show buffeting consistent with the experiment.
Computational Fluid Dynamics↗
Turbulence Simulations of Transonic Flows over NACA-0012 and OAT15A Airfoils
Three different simulation approaches, namely unsteady Reynolds-averaged Navier-Stokes (URANS), delayed detached-eddy simulation (DDES), and wall-modeled large-eddy simulation (WMLES) are employed to simulate transonic flow over an NACA-0012, OAT15A airfoils at different angles of attack covering pre- and post-buffet-onset regimes. The freestream Mach number is 0.75, and the Reynolds number based on the chord length is 10 and 3million, respectively. The NASA FUN3D solver is used for the simulations, which is an unstructured, compressible flow solver. The URANS simulations are performed using the Spalart-Allmaras (SA) model with the compressibility correction, the DDES predictions are based on the SA model, and the WMLES are performed using an equilibrium wall-model. The unsteady RANS simulations, only with the compressibility correction, predict the pre- and post- buffet characteristics, which compare well with the experimental results. DDES results predicted a lower buffet onset angle compared to experiment. The predicted shock locations are upstream of the locations predicted by URANS. Using a fine grid in the spanwise direction, WMLES predictions show buffeting consistent with the experiment.
Computational Fluid Dynamics↗
Annual Research Briefs
This report contains the 1997 annual progress reports of the research fellows and students supported by the Center for Turbulence Research (CTR). Titles include: Invariant modeling in large-eddy simulation of turbulence; Validation of large-eddy simulation in a plain asymmetric diffuser; Progress in large-eddy simulation of trailing-edge turbulence and aeronautics; Resolution requirements in large-eddy simulations of shear flows; A general theory of discrete filtering for LES in complex geometry; On the use of discrete filters for large eddy simulation; Wall models in large eddy simulation of separated flow; Perspectives for ensemble average LES; Anisotropic grid-based formulas for subgrid-scale models; Some modeling requirements for wall models in large eddy simulation; Numerical simulation of 3D turbulent boundary layers using the V2F model; Accurate modeling of impinging jet heat transfer; Application of turbulence models to high-lift airfoils; Advances in structure-based turbulence modeling; Incorporating realistic chemistry into direct numerical simulations of turbulent non-premixed combustion; Effects of small-scale structure on turbulent mixing; Turbulent premixed combustion in the laminar flamelet and the thin reaction zone regime; Large eddy simulation of combustion instabilities in turbulent premixed burners; On the generation of vorticity at a free-surface; Active control of turbulent channel flow; A generalized framework for robust control in fluid mechanics; Combined immersed-boundary/B-spline methods for simulations of flow in complex geometries; and DNS of shock boundary-layer interaction - preliminary results for compression ramp flow.
Spinks, Debra↗
On the application of a hairpin vortex model of wall turbulence to trailing edge noise prediction
The goal is to develop a technique via a hairpin vortex model of the turbulent boundary layer, which would lead to the estimation of the aerodynamic input for use in trailing edge noise prediction theories. The work described represents an initial step in reaching this goal. The hairpin vortex is considered as the underlying structure of the wall turbulence and the turbulent boundary layer is viewed as an ensemble of typical hairpin vortices of different sizes. A synthesis technique is examined which links the mean flow and various turbulence quantities via these typical vortices. The distribution of turbulence quantities among vortices of different scales follows directly from the probability distribution needed to give the measured mean flow vorticity. The main features of individual representative hairpin vortices are discussed in detail and a preliminary assessment of the synthesis approach is made.
Liu, N. S.↗
Turbulence modeling for non-equilibrium flow
The work performed during this year has involved further assessment and extension of the k-epsilon-v(exp 2) model, and initiation of work on scalar transport. The latter is introduced by the contribution of Y. Shabany to this volume. Flexible, computationally tractable models are needed for engineering CFD. As computational technology has progressed, the ability and need to use elaborate turbulence closure models has increased. The objective of our work is to explore and develop new analytical frameworks that might extend the applicability of the modeling techniques. In past years the development of a method for near-wall modeling was described. The method has been implemented into a CFD code and its viability has been demonstrated by various test cases. Further tests are reported herein. Non-equilibrium near-wall models are needed for some heat transfer applications. Scalar transport seems generally to be more sensitive to non-equilibrium effects than is momentum transport. For some applications turbulence anisotropy plays a role and an estimate of the full Reynolds stress tensor is needed. We have begun work on scalar transport per se, but in this brief I will only report on an extension of the k-epsilon-v(exp 2) model to predict the Reynolds stress tensor.
Durbin, P. A.↗
Scale resolving simulations of the NASA Juncture Flow Model using the LAVA solver
Two distinct simulation methodologies: Delayed Detached Eddy Simulation (DDES) and stress based Wall-modelled Large Eddy Simulation (WMLES) are evaluated using structured overset curvilinear grids for the NASA juncture flow model. While both methodologies are shown to mitigate the primary shortcomings of steady state Reynolds Averaged Navier Stokes(RANS) simulations, several unresolved aspects are identified. Strong sensitivity to RANS-typegrid refinement is observed in the DDES with a substantial deterioration of the solution quality with increasing spatial resolution associated with deficiencies in the shielding function. Mean profiles for attached boundary layers on the fuselage show spurious inflections suggesting modelled stress depletion on finer grids. Lower numerical dissipation in terms of spatial discretization and time step size is seen to improve the solution quality, and the advantage of using RC and QCR2000 corrections in the underlying RANS closure is demonstrated for DDES on RANS-type meshes. Equilibrium Wall-Modelled LES used grids that resolved the tripping dots over the fuselage nose and the wing leading edge, consistent with the experiment setup. These simulations resulted in a cost-competitive approach compared to DDES on RANS-type grids. Although the agreement between WMLES predictions of first and second order single point statistics with experimental measurements is promising, a fundamental shortcoming is noted in terms of an overshoot in streamwise momentum in corner regions of the wing-fuselage juncture. This excess momentum subsequently delays the onset of separation,thereby resulting in an underprediction in length of the separation bubble. Some quantitative sensitivity to numerical discretization is observed; lowering of numerical dissipation shows better agreement with the experiment.
T^3↗