Search NASA⌕ Search

SEARCH · Search NASA

Results for “Code Cases”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Flow visualization and pressure distributions for an all-body hypersonic aircraft

A CFD code-validation effort has been conducted at the NASA-Ames 3.5-ft hypersonic wind tunnel, using a generic, 'all-body' hypersonic aircraft configuration model. The CFD methods to be validated encompass approximate inviscid ones and the upwind parabolized Navier-Stokes solver code. Flow visualizations and pressure distributions are obtained for the cases of zero and 15 deg angles of attack. A complex leeward flow is observed at angle-of-attack with crossflow separation and vortices, and significant changes are noted in the transition from the forebody's conical to the afterbody's nonconical flows.

Lockman, William K.↗

VLSI Universal Noiseless Coder

Proposed universal noiseless coder (UNC) compresses stream of data signals for efficient transmission in channel of limited bandwidth. Noiseless in sense original data completely recoverable from output code. System built as very-large-scale integrated (VLSI) circuit, compressing data in real time at input rates as high as 24 Mb/s, and possibly faster, depending on specific design. Approach yields small, lightweight system operating reliably and consuming little power. Constructed as single, compact, low-power VLSI circuit chip. Design of VLSI circuit chip made specific to code algorithms. Entire UNC fabricated in single chip, worst-case power dissipation less than 1 W.

Rice, Robert F.↗

Radar RFI at Goldstone DSS 12 and DSS 16

Radio frequency interference (RFI) from the DSS 14 Goldstone Solar System Radar (GSSR) was investigated at DSS 12 and DSS 16 with the goal of assisting in the choice of the location of future DSN antennas. Total power measurements at both locations were made at the S-band carrier frequency of 2320 MHz. X-band measurements at the carrier frequency of 8495 MHz could not be made. Exciter-chain output spectrum and klystron output spectrum measurements were made at S- and X-bands using a probable worst-case modulation of the radar signal (short pseudorandom number (PN) code length and short pulse length). Based on these measurements, it is estimated that RFI levels in the DSN receiving bands at both sites (above 10-deg elevation) would be below -192 dBm for a 1-Hz bandwidth

Slobin, S. D.↗

A hybrid numerical method for three-dimensional spatially-developing free-shear flows

The present novel algorithm for 3D incompressible Navier-Stokes equations treats a domain which is (1) infinite in the vertical direction, using a mapped spectral method; (2) finite in the streamwise direction, using a classical Fourier method; and (3) homogeneous in the spanwise direction, using high-order compact finite differencing. A projection method is employed which ensures the exact conservation of mass, as well as the satisfaction of the boundary conditions at infinity. The novel aspects of these methods are noted, and the code they constitute is validated in light of several test cases. Results are presented for two- and three-dimensional mixing layers.

Buell, Jeffrey C.↗

Seal development activities at Allison Turbine Division

Brush seals are being evaluated for potential near and far term gas turbine engine applications. Development is in the form of rig component testing and engine testing. Allison has tested an engine with 20 individual brush seal positions. These seals were located throughout the engine. The emphasis of the current work is on obtaining long term performance data for brush seals. Very little of this data is available. Allison is presently developing film riding face seal technology to support future gas turbine engine applications. A face seal with an approximate 7 inch diameter was successfully tested to 1000 F, 100 psid, and 650 ft/sec. Seal leakage remained below 1 scfm throughout the duration of the test. A model for the compressible gas film was developed which separates the model for the compressible gas film was developed which separates the primary seal rings during operation. This model is based on the traditional Reynold's approach which is customarily applied to lubrication type problems. Because of the difficulty of experimentally verifying the program predictions, a commercial Navier-Stokes code was used in parallel. By comparing predictions for similar cases, it is expected that the limitations of the Reynold's model can be assessed as it applies to this particular seal.

Munson, John↗

MSAT voice modulation considerations

The challenge for Mobile satellite (MSAT) voice services is to provide near toll quality voice to the user, while minimizing the power and bandwidth resources of the satellite. The options for MSAT voice can be put into one of two groups: Analog and Digital. Analog, nominally narrowband single sideband techniques, have a shown robustness to the fading and shadowing environment. Digital techniques, a combination of low rate vocoders and bandwidth efficient modems, show the promise of enhanced fidelity, as well as easier networking to the emerging digital world. The problems and tradeoffs to designers are many, especially in the digital case. Processor speed vs. cost and MET power requirements, channel coding, bandwidth efficiency vs. power efficiency etc. While the list looks daunting, in fact an acceptable solution is well within the technology. The objectives are reviewed that the MSAT voice service must meet, along with the options that are seen for the future.

Bossler, Dan↗

Supersonic full-potential methods for missile body analysis

Accounts are presented of representative applications to missile bodies of arbitrary shape of methods based on the steady form of the full potential equation. The NCOREL and SIMP full-potential codes are compared, and their results are evaluated for the cases of an arrow wing and a wing-body configuration. Attention is given to the effect of cross-sectional and longitudinal geometries. Comparisons of surface pressure and longitudinal force and moment data for circular and elliptic bodies have shown that the full-potential methods yielded excellent results in attached-flow conditions. Results are presented for a conical star body, waveriders, the Shuttle Orbiter, and a highly swept wing-body cruising at Mach 4.

Pittman, James L.↗

Calculation of scramjet inlet with thick boundary-layer ingestion

Numerical flowfields around a scramjet inlet model are simulated and analyzed. The present inlet flowfield is characterized by thick boundary-layer ingestion and strong viscous/inviscid interaction because of a combined effect of high hypersonic freestream Mach and low Reynolds numbers. Shock-induced separation further enlarges regions of viscous flows which occupy most of the inlet flowfield. Results obtained from the computations with the PARC code developed for ideal gas are presented for several 2D cases at various hypersonic Mach numbers ranging from 10 to 25, and two 3D simulations at Mach numbers of 12 and 19 are also discussed. Comparison between computation and experiment is made in terms of pressure distributions at the wall center line. Large discrepancy is observed and may be partially attributed to the lack of real gas and/or 3D effects in the simulation as well as to the uncertainty of the experiment.

Lai, H. T.↗

Turbulence modeling for high speed compressible flows

The following grant objectives were delineated in the proposal to NASA: to offer course work in computational fluid dynamics (CFD) and related areas to enable mechanical engineering students at North Carolina A&T State University (N.C. A&TSU) to pursue M.S. studies in CFD, and to enable students and faculty to engage in research in high speed compressible flows. Since no CFD-related activity existed at N.C. A&TSU before the start of the NASA grant period, training of students in the CFD area and initiation of research in high speed compressible flows were proposed as the key aspects of the project. To that end, graduate level courses in CFD, boundary layer theory, and fluid dynamics were offered. This effort included initiating a CFD course for graduate students. Also, research work was performed on studying compressibility effects in high speed flows. Specifically, a modified compressible dissipation model, which included a fourth order turbulent Mach number term, was incorporated into the SPARK code and verified for the air-air mixing layer case. The results obtained for this case were compared with a wide variety of experimental data to discern the trends in the mixing layer growth rates with varying convective Mach numbers. Comparison of the predictions of the study with the results of several analytical models was also carried out. The details of the research study are described in the publication entitled 'Compressibility Effects in Modeling Turbulent High Speed Mixing Layers,' which is attached to this report.

Chandra, Suresh↗

Growth of zinc selenide single crystals by physical vapor transport in microgravity

The goals of this research were the optimization of growth parameters for large (20 mm diameter and length) zinc selenide single crystals with low structural defect density, and the development of a 3-D numerical model for the transport rates to be expected in physical vapor transport under a given set of thermal and geometrical boundary conditions, in order to provide guidance for an advantageous conduct of the growth experiments. In the crystal growth studies, it was decided to exclusively apply the Effusive Ampoule PVT technique (EAPVT) to the growth of ZnSe. In this technique, the accumulation of transport-limiting gaseous components at the growing crystal is suppressed by continuous effusion to vacuum of part of the vapor contents. This is achieved through calibrated leaks in one of the ground joints of the ampoule. Regarding the PVT transport rates, a 3-D spectral code was modified. After introduction of the proper boundary conditions and subroutines for the composition-dependent transport properties, the code reproduced the experimentally determined transport rates for the two cases with strongest convective flux contributions to within the experimental and numerical error.

Rosenberger, Franz↗

Rocketdyne Safety Algorithm: Space Shuttle Main Engine Fault Detection

The Rocketdyne Safety Algorithm (RSA) has been developed to the point of use on the TTBE at MSFC on Task 4 of LeRC contract NAS3-25884. This document contains a description of the work performed, the results of the nominal test of the major anomaly test cases and a table of the resulting cutoff times, a plot of the RSA value vs. time for each anomaly case, a logic flow description of the algorithm, the algorithm code, and a development plan for future efforts.

Norman, Arnold M., Jr.↗

Operating in the space plasma environment: A spacecraft charging study of the Solar X-ray Imager

This study presents the results of a spacecraft charging effects protection study conducted on the Solar X-ray Imager (SXI). The SXI is being developed by NASA Marshall Space Flight Center for NOAA's Space Environment Laboratory, and will be used to aid in forecasting energetic particle events and geomagnetic storms. Images will provide information on the intensity and location of solar flares, coronal mass ejections, and high speed solar streams. The SXI will be flown on a next-generation GOES sometime in the mid to late 1990's. Charging due to the encounter with a worst-case magnetic substorm environment is modeled using the NASCAP/GEO computer code. Charging levels of exterior surfaces and the floating potential of the spacecraft relative to plasma are determined as a function of spacecraft design, operational configuration, and orbital conditions. Areas where large surface voltage gradients exist on or near the SXI are identified as possible arc-discharge sites. Results of the charging analysis are then used to develop design recommendations that will limit the effects of spacecraft charging on the SXI operation.

Herr, Joel L.↗

Implementation of a two-equation k-omega turbulence model in NPARC

The implementation of a two-equation k-omega turbulence model into the NPARC flow solver is described. Motivation for the selection of this model is given, major code modifications are outlined, new imputs to the code are described, and results are presented for several validation cases: an incompressible flow over a smooth flat plate, a subsonic diffuser flow, and a shock-induced separated flow. Comparison of results with the k-epsilon model indicate that the k-omega model predicts simple flows equally well whereas, for adverse pressure gradient flows, the k-omega model outperforms the other turbulence models in NPARC.

Yoder, Dennis A.↗

Turbulence modeling for non-equilibrium flow

The work performed during this year has involved further assessment and extension of the k-epsilon-v(exp 2) model, and initiation of work on scalar transport. The latter is introduced by the contribution of Y. Shabany to this volume. Flexible, computationally tractable models are needed for engineering CFD. As computational technology has progressed, the ability and need to use elaborate turbulence closure models has increased. The objective of our work is to explore and develop new analytical frameworks that might extend the applicability of the modeling techniques. In past years the development of a method for near-wall modeling was described. The method has been implemented into a CFD code and its viability has been demonstrated by various test cases. Further tests are reported herein. Non-equilibrium near-wall models are needed for some heat transfer applications. Scalar transport seems generally to be more sensitive to non-equilibrium effects than is momentum transport. For some applications turbulence anisotropy plays a role and an estimate of the full Reynolds stress tensor is needed. We have begun work on scalar transport per se, but in this brief I will only report on an extension of the k-epsilon-v(exp 2) model to predict the Reynolds stress tensor.

Durbin, P. A.↗

Application of the ENS3DAE Euler/Navier-Stokes Aeroelastic method

This paper discusses recent applications of the ENS3DAE computational aeroelasticity method. In particular, it describes aeroelastic and unsteady aerodynamics calculations performed on wings with trailing edge control surfaces. These simulations include the investigation of control reversal for a structurally flexible wing with a deflected control surface, and a static and dynamic analysis of a rigid wing with an oscillating control surface. The two sets of calculations were performed independently on different wings using different grid topologies. The control reversal simulation represents an inviscid Euler static aeroelastic analysis of a thin wing with a rectangular planform. The geometry of this wing makes it suitable for computations using more approximate, inviscid aerodynamics methods. Thus, the results of the present Euler computations are compared with numerical data generated by a validated computational aeroelasticity code which uses a simpler aerodynamic formulation. The second illustrated case involves the simulation of a significantly more complex flowfield and the static and dynamic analyses of this geometry were performed using the viscous Navier-Stokes equation option in ENS3DAE. Results of both the steady and unsteady calculations on this wing are compared with existing experimental data.

Schuster, David M.↗

Corrugated and Composite Nozzle-Inlets for Thrust and Noise Benefits

The following research results are based on development of an approach previously proposed and investigated in for optimum nozzle design to obtain maximum thrust. The design was denoted a Telescope nozzle. A Telescope nozzle contains one or several internal designs, which are inserted at certain locations into a divergent conical or planar main nozzle near its exit. Such a design provides additional thrust augmentation over 20% by comparison with the optimum single nozzle of equivalent lateral area, What is more, experimental acoustic tests have discovered an essential noise reduction due to application of Telescope nozzles. In this paper, some additional theoretical results are presented for Telescope nozzles and a similar approach is applied for aero-performance improvement of a supersonic inlet. Numerical simulations were conducted for supersonic flow into the divergent portion of a 2D or axisymmetric nozzle with several plane or conical designs as well as into a 2D or axisymmetric supersonic inlet with a forebody. The Kryko-Godunov marching numerical scheme for inviscid supersonic flows was used. Several cases were tested using the NASA CFL3d and IM/MSU Russian codes based on the full Navier-Stokes equations. Numerical simulations were conducted for non reacting flows (both codes) as well as for real high temperature gas flows with non-equilibrium chemical reactions (the latter code). In general, these simulations have confirmed essential benefits of Telescope design applications in propulsion system. Some preliminary numerical simulations of several typical inlet designs were conducted with the goal of inlet design optimization for maneuvering flight conditions.

Gilinsky, M.↗

Aerothermodynamics Overview and Prediction Assessment

An overview of the Aerothermodynamics Discipline within NASA s Subsonic Fixed Wing Project is given. The primary focus of the presentation is on the research efforts conducted in fiscal year 2007. This year (2007), the work primarily consisted of efforts under level 1 (foundational research) and level 2 (tools and technology development). Examples of work under level 1 are large eddy simulation development, advanced turbine cooling concept development, and turbomachinery flow control development. Examples of level 2 research are the development of highly-loaded compressor and turbine test programs and advanced turbomachinery simulation development, including coupled inlet-fan simulations. An overview of the NRA research activity is also provided. This NRA focused on plasma and aspiration flow control for low pressure turbine application. Finally, a status report on the turbomachinery CFD code assessment activity is provided. This activity focuses on the use of several NASA in-house codes for the NASA rotor 37 and stage 35 test cases.

Heidmann, James D.↗

An Overview of Ares-I CFD Ascent Aerodynamic Data Development And Analysis Based on USM3D

An overview of the computational results obtained from the NASA Langley developed unstructured grid, Reynolds-averaged Navier-Stokes flow solver USM3D, in support of the Ares-I project within the NASA s Constellation program, are presented. The numerical data are obtained for representative flow conditions pertinent to the ascent phase of the trajectory at both wind tunnel and flight Reynolds number without including any propulsion effects. The USM3D flow solver has been designated to have the primary role within the Ares-I project in developing the computational aerodynamic data for the vehicle while other flow solvers, namely OVERFLOW and FUN3D, have supporting roles to provide complementary results for fewer cases as part of the verification process to ensure code-to-code solution consistency. Similarly, as part of the solution validation efforts, the predicted numerical results are correlated with the aerodynamic wind tunnel data that have been generated within the project in the past few years. Sample aerodynamic results and the processes established for the computational solution/data development for the evolving Ares-I design cycles are presented.

FUN3D↗