Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffuser Flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Advantages of the diffuser-augmented wind turbine

Performance optimization for a wind turbine is realized by using a shrouded diffuser to produce up to twice the power of unshrouded turbines of the same diameter. The diffuser converts the kinetic energy of the flow downstream of the rotor into a pressure rise and thus makes it possible for the rotor to capture airflow from a free stream tube area that is greater than that from the rotor itself. The flow velocity through the shrouded rotor is 20 to 60 percent greater than the free wind velocity as opposed to 67 percent less for the unshrouded case. The diffuser also makes it possible to accommodate very high wind speeds without the need of variable pitch in the rotor blades.

Oman, R. A.↗

Influence of Gravity on Blood Volume and Flow Distribution

In our previous experiments during NASA Shuttle flights SLS 1 and 2 (9-15 days) and EUROMIR flights (30-90 days) we observed that pulmonary blood flow (cardiac output) was elevated initially, and surprisingly remained elevated for the duration of the flights. Stroke volume increased initially and then decreased, but was still above 1 Gz values. As venous return was constant, the changes in SV were secondary to modulation of heart rate. Mean blood pressure was at or slightly below 1 Gz levels in space, indicating a decrease in total peripheral resistance. It has been suggested that plasma volume is reduced in space, however cardiac output/venous return do not return to 1 Gz levels over the duration of flight. In spite of the increased cardiac output, central venous pressure was not elevated in space. These data suggest that there is a change in the basic relationship between cardiac output and central venous pressure, a persistent "hyperperfusion" and a re-distribution of blood flow and volume during space flight. Increased pulmonary blood flow has been reported to increase diffusing capacity in space, presumably due to the improved homogeneity of ventilation and perfusion. Other studies have suggested that ventilation may be independent of gravity, and perfusion may not be gravity- dependent. No data for the distribution of pulmonary blood volume were available for flight or simulated microgravity. Recent studies have suggested that the pulmonary vascular tree is influenced by sympathetic tone in a manner similar to that of the systemic system. This implies that the pulmonary circulation is dilated during microgravity and that the distribution of blood flow and volume may be influenced more by vascular control than by gravity. The cerebral circulation is influenced by sympathetic tone similarly to that of the systemic and pulmonary circulations; however its effects are modulated by cerebral autoregulation. Thus it is difficult to predict if cerebral perfusion is increased and if there is edema in space. Anecdotal evidence suggests there may be cerebral edema early in flight. Cerebral artery velocity has been shown to be elevated in simulated microgravity. The elevated cerebral artery velocity during simulated microgravity may reflect vasoconstriction of the arteries and not increased cerebral blood flow. The purpose of our investigations was to evaluate the effects of alterations in simulated gravity (+/-), resulting in changes in cardiac output (+/-), and on the blood flow and volume distribution in the lung and brain of human subjects. The first hypothesis of these studies was that blood flow and volume would be affected by gravity, but their distribution in the lung would be independent of gravity and due to vasoactivity changing vascular resistance in lung vessels. The vasodilitation of the lung vasculature (lower resistance) along with increased "compliance" of the heart could account for the absence of increased central venous pressure in microgravity. Secondly, we postulate that cerebral blood velocity is increased in microgravity due to large artery vasoconstriction, but that cerebral blood flow would be reduced due to autoregulation.

Pendergast, D.↗

Generative AI for Wind-Wave Inflows

Extreme wind-wave conditions can create dangerous or damaging environmental conditions for sea-based structures and watercrafts. However, the model of consistent, coupled wind-wave flow conditions is computational expensive, even for simple flow scenarios. This work examines the use of diffusion-based generative artificial intelligence tools to accelerate the generation of these two-phase flows and to characterize probabilities of various states to help with the generation of extreme patterns.

17 WIND ENERGY↗

Numerical solutions for the spin-up of a stratified fluid

The model of Warn-Varnas et al. (1978) is used to numerically examine the spin-up flow of a thermally stratified fluid in a cylinder with an insulating side wall, and comparison of the results with the laser-Doppler measurements of Lee (1975) shows excellent agreement. It is shown that flow gradients are created in the interior of the fluid during the meridional circulation spin-up phase, and that the azimuthal flow decayed faster than has been predicted by Wallin (1969). It is established that viscous diffusion in the interior, arising from the interior-flow gradients, is the cause of the discrepancy with Wallin's theory.

Hyun, J. M.↗

Cation-Diffusive Carbon Interlayers Stabilize Na Metal and Double the Current in Na-S Redox-Flow Batteries for Grid-Scale Energy Storage

The sodium-sulfur nonaqueous redox-flow batteries (Na-S NARFBs) using earth-abundant elements are highly attractive due to the low material cost and improved energy density for grid-scale energy storage. However, the low current performance, poor Na0/Na+ redox kinetics, and Na dendrite growth pose severe challenges. We introduce cation-diffusive layers (CDLs): thin and Na+ affinitive interlayers at the Na anode that direct Na+ transport and stabilize Na deposition. Benchmarking three archetypal materials—carbon paper (CP), glass microfiber paper (GF), and foam—across Na-Na and Na-Cu, and Na-S cells identifies CP as the optimum. CP reduces symmetric cell overpotential by more than 70%, achieves 98% Na plating-stripping efficiency, and doubles the Na-S cell current density from 0.5 to 1.0 mA cm−2 without sacrificing capacity or efficiency. Ex situ electrochemical and SEM/XPS analysis, combined with molecular dynamics (MD) studies, reveal that electron-rich carbon fibers disperse supporting salt aggregates, enrich near-surface Na+ density, and create ion transport pathways for fast Na0/Na+ exchange while mitigating membrane degradation. Because of the ion-centric mechanism, CDLs can be generalized to other metal-anode designs. Further, this work establishes CDL design rules—cationic affinity and appropriate micro/nanostructure—as a simple, scalable route to high-current, durable metal-anode flow batteries.

Wu, Wenda [ORNL] (ORCID:000900033307687X)↗

Numerical simulation of flow through inlets/diffusers with terminal shocks

Two-dimensional Euler and Navier-Stokes solutions of the flow through three inlet/diffuser configurations with terminal shock systems are reported. Calculations without bleed indicate that the terminal shock location is very sensitive to the outflow back pressure. For cases where there are no available experimental results, it becomes difficult to estimate the back pressure that will result in a terminal shock. Estimates based on quasi-one-dimensional analysis are not found adequate for complex two-dimensional flows. It is found that since the flow downstream of the terminal shock is subsonic, and what happens at the outflow boundary affects the flow inside the inlet, enough of the subsonic diffuser must be modeled to accurately predict the terminal shock region. The diffuser portion should be fairly long with the outflow boundary occurring in a region of more or less uniform flow to be able to prescribe a uniform back pressure. The third configuration studied was investigated with and without incorporating bleed in the code. It is found that the use of bleed stabilizes the shock location and allows solutions which without bleed result in unstarting of the inlet. Comparisons are made with available experimental data.

Talcott, N. A., Jr.↗

Computational Study on the Effect of Thermal Boundary Conditions and Axial Aspect Ratio on Catalytic Oxidative Coupling of Methane

Packed-bed reactor models with a large reactor-diameter-to-particle-diameter ratio (N > 10) are commonly used in catalysis research. Their use is underpinned by strong simplifying assumptions including unidirectional plug flow, negligible radial gradients, small axial diffusion, and isothermal operation. However, the complex exothermic–endothermic nature of reactions like oxidative coupling of methane (OCM) coupled with heat transfer from the catalyst surface and convective heat losses from the reactor wall provides an interesting case study to evaluate packed-bed assumptions and understand axial and radial temperature variations that may impact conversion and selectivity. This computational study investigates the effect of thermal boundary conditions on catalyst performance in laboratory OCM reactors (N = ~13) through computational fluid dynamics (CFD) simulation. Further, the 1-D model typically used for modeling plug flow reactors assumes negligible radial temperature and species concentration gradients. This assumption is evaluated for OCM reactors over a range of geometric axial aspect ratios, defined as the reactor length divided by the diameter, comparing the 1-D with 3-D CFD results. 1-D model predictions of catalyst performance start to deviate from the 3-D model predictions as the axial aspect ratio decreases, specifically as diameter increases at constant length. In the work, the 1-D model assumption is only found to be valid for axial aspect ratios higher than 1.6, a result considered to be relevant for all exothermic catalytic reactors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Large Sample Volume Magic Angle Spinning Nuclear Magnetic Resonance Probe for In-Situ Investigations with Constant Flow of Reactants

A large-sample-volume constant-flow magic angle sample spinning (CF-MAS) NMR probe is reported for in-situ studies of the reaction dynamics, stable intermediates/transition states, and mechanisms of catalytic reactions. In our approach, the reactants are introduced into the catalyst bed using a fixed tube at one end of the MAS rotor while a second fixed tube, linked to a vacuum pump, is attached at the other end of the rotor. The pressure difference between both ends of the catalyst bed inside the sample cell space forces the reactants flowing through the catalyst bed, which improves the diffusion of the reactants and products. This design allows the use of a large sample volume for enhanced sensitivity and thus permitting in-situ 13C CF-MAS studies at natural abundance. As an example of application, we show that reactants, products and reaction transition states associated with the 2-butanol dehydration reaction over a mesoporous silicalite supported heteropoly acid catalyst (HPA/meso-silicalite-1) can all be detected in a single 13C CF-MAS NMR spectrum at natural abundance. Coke products can also be detected at natural 13C abundance and under the stopped flow condition. Furthermore, 1H CF-MAS NMR is used to identify the surface functional groups of HPA/meso-silicalite-1 under the condition of in-situ drying . We also show that the reaction dynamics of 2-butanol dehydration using HPA/meso-silicalite-1 as a catalyst can be explored using 1H CF-MAS NMR.

01 COAL, LIGNITE, AND PEAT↗

Unsteady Spherical Diffusion Flames in Microgravity

The absence of buoyancy-induced flows in microgravity (mu-g) and the resulting increase in the reactant residence time significantly alters the fundamentals of many combustion processes. Substantial differences between normal gravity (ng) and (mu-g) flames have been reported in experiments on candle flames, flame spread over solids, droplet combustion, and others. These differences are more basic than just in the visible flame shape. Longer residence times and higher concentration of combustion products in the flame zone create a thermochemical environment that changes the flame chemistry and the heat and mass transfer processes. Processes such as flame radiation, that are often ignored in ng, become very important and sometimes even controlling. Furthermore, microgravity conditions considerably enhance flame radiation by: (i) the build-up of combustion products in the high-temperature reaction zone which increases the gas radiation, and (ii) longer residence times make conditions appropriate for substantial amounts of soot to form which is also responsible for radiative heat loss. Thus, it is anticipated that radiative heat loss may eventually extinguish the "weak" (low burning rate per unit flame area) mu-g diffusion flame. Yet, space shuttle experiments on candle flames show that in an infinite ambient atmosphere, the hemispherical candle flame in mu-g will burn indefinitely. This may be because of the coupling between the fuel production rate and the flame via the heat-feedback mechanism for candle flames, flames over solids and fuel droplet flames. Thus, to focus only on the gas-phase phenomena leading to radiative extinction, aerodynamically stabilized gaseous diffusion flames are examined. This enables independent control of the fuel flow rate to help identify conditions under which radiative extinction occurs. Also, spherical geometry is chosen for the mu-g experiments and modeling because: (i) It reduces the complexity by making the problem one-dimensional; (ii) The spherical diffusion flame completely encloses the soot which is formed on the fuel rich side of the reaction zone. This increases the importance of flame radiation because now both soot and gaseous combustion products co-exist inside the high temperature spherical diffusion flame. (iii) For small fuel injection velocities, as is usually the case for a pyrolyzing solid, the diffusion flame in mu-g around the solid naturally develops spherical symmetry. Thus, spherical diffusion flames are of interest to fires in mu-g and identifying conditions that lead to radiation-induced extinction is important for spacecraft fire safety.

Atreya, Arvind↗

The Effect of the Inlet Mach Number and Inlet-boundary-layer Thickness on the Performance of a 23 Degree Conical-diffuser-tail-pipe Combination

An investigation was conducted to determine the effect of the inlet Mach number and entrance-boundary-layer thickness on the performance of a 23 degree 21-inch conical-diffuser - tail-pipe combination with a 2:1 area ratio. The air flows used in this investigation covered an inlet Mach number range from 0.17 to 0.89 and corresponding Reynolds numbers of 1,700,000 to 7,070,000. Results are reported for two inlet-boundary-layer thicknesses. Over the entire range of flows, the mean value of the inlet displacement thickness is about 0.034 inch for the thinner inlet boundary layer and about 0.170 inch for the case of the thicker inlet boundary layer. The performance of the diffuser - tail-pipe combination is presented together with examples of longitudinal static-pressure distribution and the results of boundary-layer pressure surveys made at six points along the diffuser wall. The results indicated a progressive diminution of the static-pressure recovery and a steady increase in the total-pressure losses as the inlet Mach number was increased for both inlet-boundary-layer thicknesses. The ratio of actual static-pressure rise to that theoretically possible was much less and the total-pressure losses were greater for the case of the thicker inlet boundary layer throughout the speed range investigated. With the thinner inlet boundary layer, flow separation occurred at the diffuser exit at all inlet Mach numbers.Unseparated flow alternating with separated flow was observed near the inlet at the higher velocities. For the case of the thicker inlet boundary layer, the origin of the separated region occurred in the vicinity of the inlet-duct-diffuser junction section at all Mach numbers.

Persh, Jerome↗

Pulmonary diffusing capacity, capillary blood volume, and cardiac output during sustained microgravity

We measured pulmonary diffusing capacity (DL), diffusing capacity per unit lung volume, pulmonary capillary blood volume (Vc), membrane diffusing capacity (Dm), pulmonary capillary blood flow or cardiac output (Qc), and cardiac stroke volume (SV) in four subjects exposed to nine days of microgravity. DL in microgravity was elevated compared with preflight standing values and was higher than preflight supine because of the elevation of both Vc and Dm. The elevation in Vc was comparable to that measured supine in 1 G, but the increase in Dm was in sharp contrast to the supine value. We postulate that, in 0 G, pulmonary capillary blood is evenly distributed throughout the lung, providing for uniform capillary filling, leading to an increase in the surface area available for diffusion. By contrast, in the supine 1-G state, the capillaries are less evenly filled, and although a similar increase in blood volume is observed, the corresponding increase in surface area does not occur. DL and its subdivisions showed no adaptive changes from the first measurement 24 h after the start of 0 G to eight days later. Similarly, there were no trends in the postflight data, suggesting that the principal mechanism of these changes was gravitational. The increase in Dm suggests that subclinical pulmonary edema did not result from exposure to 0 G. Qc was modestly increased inflight and decreased postflight compared with preflight standing. Compared with preflight standing, SV was increased 46 percent inflight and decreased 14 percent in the 1st week postflight. There were temporal changes in Qc and SV during 0 G, with the highest values recorded at the first measurement, 24 h into the flight. The lowest values of Qc and SV occurred on the day of return.

Prisk, G. K.↗

Liquid–Solid Boundaries Dominate Activity of CO 2 Reduction on Gas-Diffusion Electrodes

Electrochemical CO 2 electrolysis to produce hydrocarbon fuels or material feedstocks offers a renewable alternative to fossilized carbon sources. Gas-diffusion electrodes (GDEs), composed of solid electrocatalysts on porous supports positioned near the interface of a conducting electrolyte and CO 2 gas, have been able to demonstrate the substantial current densities needed for future commercialization. These higher reaction rates have often been ascribed to the presence of a three-phase interface, where solid, liquid, and gas provide electrons, water, and CO 2 , respectively. Conversely, mechanistic work on electrochemical reactions implicates a fully two-phase reaction interface, where gas molecules reach the electrocatalyst’s surface by dissolution and diffusion through the electrolyte. Because the discrepancy between an atomistic three-phase versus two-phase reaction has substantial implications for the design of catalysts, gas-diffusion layers, and cell architectures, the nuances of nomenclatures and governing phenomena surrounding the three-phase-region require clarification. In this paper we outline the macro, micro, and atomistic phenomena occurring within a gas-diffusion electrode to provide a focused discussion on the architecture of the often-discussed three-phase region for CO 2 electrolysis. From this information, we comment on the outlook for the broader CO 2 electroreduction GDE cell architecture.

CO2 reduction↗

Domain decomposition algorithms and computation fluid dynamics

In the past several years, domain decomposition was a very popular topic, partly motivated by the potential of parallelization. While a large body of theory and algorithms were developed for model elliptic problems, they are only recently starting to be tested on realistic applications. The application of some of these methods to two model problems in computational fluid dynamics are investigated. Some examples are two dimensional convection-diffusion problems and the incompressible driven cavity flow problem. The construction and analysis of efficient preconditioners for the interface operator to be used in the iterative solution of the interface solution is described. For the convection-diffusion problems, the effect of the convection term and its discretization on the performance of some of the preconditioners is discussed. For the driven cavity problem, the effectiveness of a class of boundary probe preconditioners is discussed.

Chan, Tony F.↗

Scattering of light passing through a statistically rough interface between media with different refractive indices after laser correction of vision

Forward scattering of light passing through large-scale irregularities of the interface between two media having different refractive indices is considered. An analytical expression for the ratio of intensities of directional and diffusion components of scattered light in the far-field zone is derived. It is theoretically shown that the critical depth of possible interface relief irregularities, starting from which the intensity of the diffuse component in the passing light flow becomes comparable with the directional light component, responsible for the image formation on the eye retina, is 3 - 4 {mu}m, with the increase in the refractive index in the postoperational zone taken into account. These profile depth values agree with the experimentally measured ones and may affect the contrast sensitivity of vision.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Onset of kinetic effects on Rayleigh–Taylor instability: Advective–diffusive asymmetry

In nature and engineering applications, the Rayleigh–Taylor instability (RTI) occurs over a wide range of Atwood, Reynolds, Mach, and Knudsen numbers. At low Atwood, Mach, and Knudsen numbers, the classic advective instability causes quasi-symmetric bubble and spike growth on the two sides of the interface. However, recent findings suggest that at high degrees of rarefaction, advective effects are suppressed and molecular diffusion leads to planar growth of the density fronts on either side of the interface. This study aims to investigate the flow physics of the transition from advective to diffusive behavior, focusing on the onset of the kinetic effects. Using the gas kinetic methodology, RTI is simulated over a range of Knudsen and Mach numbers in the transition regime. The simulation results reveal the various stages of transformation from advective instability to diffusive transport. For the first time, the study demonstrates the existence of a Knudsen–Mach parameter regime where the bubble side exhibits advective instability, while the other side shows a planar density front due to molecular diffusion, rather than the canonical advective spike shape. The dominance of different mechanisms on the two sides of the interface leads to the advective–diffusive asymmetry. In conclusion, the findings of this study can lead to a more comprehensive understanding of RTI over a wide range of Mach and Knudsen numbers.

42 ENGINEERING↗

Comment on the paper 'On the influx of small comets into the earth's upper atmosphere. II - Interpretation' by L. A. Frank, J. B. Sigwarth and J. D. Craven

The proposal by Frank et al. (1986) that clouds of small comets periodically inject large amounts of H2O into the upper atmospheres of the earth, Venus, and Mars is examined critically, with a focus on transport and disposal mechanisms invoked to account for the large H2O masses involved. It is argued that observed parameter values (such as mixing ratios, vertical wind velocities, and H escape flows) prohibit transport by eddy, molecular diffusion, vertical avection, or coherent movement. In a reply by Frank et al., these objections are discussed in terms of an overall description of the decelerataion and penetration of a cometary water cloud, and H2O concentrations and mixing mechanisms consistent with observed values for the earth are proposed. It is suggested that an increase in cometary H2O influx could lead to concentrations attaining the frost point and to formation of a global mesospheric cloud with significant climate effects. A lower H2O influx rate for Venus (consistent with observed H loss and atmospheric H2O concentration) and relatively rapid loading of the Mars surface and atmosphere with H2O ice and vapor (followed by brief warming periods with increased exospheric H2O outflow and surface flow of liquid H2O) are considered.

Donahue, T. M.↗

Modeling of Sediment Bed Behavior for Critical Velocity in Horizontal Piping

This paper compares results from a predictive tool for modeling transport of a multiphase mixture (solids in a liquid) in a pipeline, (up to and including plugging) with experiments performed to support the Hanford site’s Waste Treatment and Immobilization Plant (WTP). The treatment of high-level waste at the DOE Office of River Protection’s WTP will involve the transfer of high solid content suspensions through pipelines. Pipeline plugging was identified as a significant potential issue by a panel of external experts. In response to their concerns an experimental effort was initiated at PNNL to determine the critical velocities for a variety of operating conditions. A computational method has been developed to predict the dynamic behavior of a sediment bed in response to the surrounding suspension flow. The flow field is modeled using a lattice kinetics method, similar to the lattice Boltzmann method, which scales very well on highly parallel computers. Turbulent quantities are calculated using a k-epsilon RANS model. This work is part of a larger effort to develop a process simulation capability for a wide range of applications. Solids are represented using two different continuum fields. The suspended solids are treated as passive scalars in the flow field, including terms for hindered settling and Brownian diffusion. Normal stresses created by the irreversible collisions of particles during shearing are added to the pressure tensor. The sediment bed interface is represented using a continuum phase field with a diffuse interface. The bed may change with time due to settling, erosion and deposition through convection. The erosion rates are calculated using the local shear stress obtained from the turbulence model. The method is compared with data from the PNNL pipeline experiments conducted at PNNL (Poloski et al. 2008). The experimental flow loop consists of 3-inch schedule 40 piping with instrumentation for determining flow rate and pressure gradient. The simulant test particles ranged in density from 2.5 to 8 g/cc while the nominal particle size ranged from 10 to 100 μm. At the beginning of each test, the slurry flow velocity was nominally set to 8 ft/sec. The flow was incrementally ramped down, and a steady-state pressure gradient was obtained at each flow condition. A rise in pressure gradient as the flow rate drops indicates that the pipe cross-sectional area is beginning to fill with sediment. This point is referred to as the “critical velocity”. Visualization information is provided using Electrical Resistance Tomography (ERT). The paper will show favorable comparison of results with data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗