Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engineering prototypes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Fabrication of Bi-2212 Canted-Cosine-Theta Dipole Prototypes

The U.S. Magnet Development Program (MDP) is exploring the possibility of combining low-and higherature superconductor technologies, using cosine-theta and canted-cosine-theta (CCT) Nb3Sn dipole magnets together with Bi-2212 CCT inserts, with the ultimate goal of constructing a 20-T dipole. The MDP short-term goal is a Bi-2212 CCT insert capable of reaching 5 T in the bore when operating as a stand-alone and 3 T when operating under a background field of 15 T. This paper reports on the fabrication of our BIN4 dipole magnet and our BIN5a and BIN5b coils, designed and built at the Lawrence Berkeley National Laboratory to address potential fabrication issues of Bi-2212 coils and verify the design of our 18-20-T dipole magnet. BIN4 is a two-layer 50-cm-long CCT magnet that uses a nine-strand Rutherford cable made with 0.8-mm-diameter Bi-2212 strands. Its goal is to investigate critical current, insulation integrity, manufacturing challenges, and quench protection issues after heat treating both layers together under oxygen at standard atmosphere (1 bar). BIN5a and BIN5b are two identical coils, similar to the outer layer of BIN4, with the difference that the length is 39 cm, and they will undergo 50-bar overpressure processing heat treatment. Finally, BIN5 coils are made from the state-of-the-art strand with an engineering critical current density of 1150 A/mm 2 at 4.2 K and 5 T.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Testing of inductively coupled Eddy current position sensor of diverse safety rod in sodium

Prototype Fast Breeder Reactor (PFBR) is 500 MWe sodium cooled reactor under construction at Kalpakkam (India)). To improve the reliability of shutdown, Diverse Safety Rods (DSRs) are used in-addition to normal Control and Safety rods. During reactor operating condition, the DSR is parked above the active core and held in its top position by an electromagnet. In the event of a scram signal from the safety logic, the electromagnet holding the DSR is de-energised. Hence the DSR is released into the active core and at the end of travel DSR gets deposited in its bottom position. Because of the mechanical constraints, hard wired connectivity is not permitted from the DSR subassembly to the instrumentation outside the reactor. Hence an inductively coupled Eddy Current Position Sensor (ECPS) has been conceptualized to detect that the DSR has reached its bottom most position and to measure the drop time. Results of feasibility study on laboratory model have been reported earlier. Testing of a 1:1 scale engineering model of ECPS is reported in this paper. Results obtained from the high temperature sodium testing of ECPS indicate a clearly measurable change in pick up voltage with sensitivity of 11 % at 675 Hz. The ECPS is in advanced stage of implementation in DSRDM of PFBR. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Directed Self-Assembly of the Organic Semiconductor C8-BTBT-C8 in Anodic Aluminum Oxide Nanopores

Controlling the self-assembly of organic semiconductors at the nanoscale is critical for advancing high-performance electronic and photonic devices, yet it remains challenging due to their intrinsic anisotropic crystallization and sensitivity to processing conditions. Here, in this study, we demonstrate that cylindrical nanoconfinement within anodic aluminum oxide membranes provides a versatile platform to precisely tune the molecular orientation and phase behavior of the prototypical organic semiconductor 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT-C8). Combining temperature-dependent high-resolution synchrotron X-ray scattering with optical birefringence measurements, we uncover that confinement geometries (pore diameters 25–180 nm) and surface chemistry govern the emergence of distinct smectic A textures, featuring molecular layers either parallel or perpendicular to the pore axis. The competition between axial and radial smectic layering is modulated by pore size, surface hydrophilicity, and thermal history, enabling reversible control over domain orientations and transitions between liquid crystalline and crystalline states. Notably, nanoconfinement stabilizes the smectic phase over an expanded temperature range compared to bulk, while inducing complex multidomain configurations owing to geometric constraints and anchoring conditions. Our results elucidate fundamental mechanisms by which anisotropic nanoscale confinement directs the self-organization of highly conjugated organic molecules, with implications for optimizing directional charge transport and anisotropic optical responses in organic–inorganic hybrid nanoarchitectures. This study establishes nanoconfinement as a powerful strategy to engineer morphology and functional properties in organic semiconducting materials with nanoscale precision.

36 MATERIALS SCIENCE↗

Modeling for Process Control: High-Dimensional Systems

Most of other technologically important systems (among them, powders and other granular systems) are intrinsically nonlinear. This project is focused on building the dynamical models for granular systems as a prototype for nonlinear high-dimensional systems exhibiting complex non-equilibrium phenomena. Granular materials present a unique opportunity to study these issues in a technologically important and yet fundamentally interesting setting. Granular systems exhibit a rich variety of regimes from gas-like to solid-like depending on the external excitation. Based the combination of the rigorous asymptotic analysis, available experimental data and nonlinear signal processing tools, we developed a multi-scale approach to the modeling of granular systems from detailed description of grain-grain interaction on a micro-scale to continuous modeling of large-scale granular flows with important geophysical applications.

42 ENGINEERING↗

Insulation Coordination Design for Grid-Connected Solid-State Transformers

The deployment of solid-state transformers (SSTs) in medium-voltage (MV) distribution systems is facing various challenges, especially the challenge of insulation coordination design against grid-originated lightning impulses. In this article, two challenges in existing insulation coordination designs for grid-connected SSTs are identified. One challenge is the mismatch between metal-oxide varistor (MOV) protective levels and SST insulation strength, the other challenge is the incompatibility of standard impulse test on SST protective structures. To address the MOV selection challenge, a novel lightning protection scheme is designed to protect a single-stage SST where the semiconductor modules are directly exposed to external lightning impulses. Here, the in-lab lightning impulse tests are performed to verify the overvoltage attenuation performance of the prototyped lightning protection scheme. To address the impulse test challenge, the surge withstand capability of the protected SST is comprehensively evaluated with a complete set of insulation coordination design procedures beyond the basic insulation level (BIL) test. After these two challenges are addressed, a discussion is presented on substituting conventional transformers with the protected SSTs into insulation-coordinated distribution systems to facilitate the field deployment of SSTs.

solid-state transformer (SST)↗

Direct electron beam patterning of electro-optically active PEDOT:PSS

The optical and electronic tunability of the conductive polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has enabled emerging applications as diverse as bioelectronics, flexible electronics, and micro- and nano-photonics. High-resolution spatial patterning of PEDOT:PSS opens up opportunities for novel active devices in a range of fields. However, typical lithographic processes require tedious indirect patterning and dry etch processes, while solution-processing methods such as ink-jet printing have limited spatial resolution. Here, we report a method for direct write nano-patterning of commercially available PEDOT:PSS through electron-beam induced solubility modulation. The written structures are water stable and maintain the conductivity as well as electrochemical and optical properties of PEDOT:PSS, highlighting the broad utility of our method. We demonstrate the potential of our strategy by preparing prototypical nano-wire structures with feature sizes down to 250 nm, an order of magnitude finer than previously reported direct write methods, opening the possibility of writing chip-scale microelectronic and optical devices. We finally use the high-resolution writing capabilities to fabricate electrically-switchable optical diffraction gratings. We show active switching in this archetypal system with >95 % contrast at CMOS-compatible voltages of +2 V and -3 V, offering a route towards highly-miniaturized dynamic optoelectronic devices.

42 ENGINEERING↗

Energy Saving Glass Lamination via Selective Radio Frequency Heating

This project focused on advancing radio-frequency (RF) lamination technology closer to commercial implementation, in order to reduce the energy intensity of glass lamination by up to 90%. Lamination comprises a wide range of products including autoglass, architectural safety and innovative design glass, transparent armor (e.g. bullet proof glass), smart glass, mirrors, and encapsulation of photovoltaics. Lamination is also the fastest growing segment of glass manufacturing, with photovoltaics, architectural needs, and an anticipated transition to laminated side windows in vehicles. The state-of-the-art for glass lamination is to use autoclaves, which apply heat and uniform gas pressure to bond the laminates over the course of 1 to 18 hours. Laminates consist of layers of glass or other materials bonded with vinyl or urethane interlayers. In autoclaving, significant heat energy is lost heating the chamber, pressurized air, glass racks, and the glass. In RF lamination, the heat is generated directly in the vinyl interlayer, causing it to heat and melt quickly, in just 1 to 10 minutes, without significantly heating the glass or the equipment. The main purpose of this project was to provide evidence that low energy, rapid RF lamination quality met the same standards as conventionally autoclaved windows. The development of concepts for laminating curved glass with RF lamination was a major goal. Other primary goals included developing a stronger understanding of the lamination product markets described above, and to refine the potential benefits of commercial implementation. The scope of the project was to complete implementation concept studies in preparation for continuation into advanced development, pilot studies, and commercial implementation. The project consisted of 6 main tasks. The first dealt with lamination with poly-vinyl butyral (PVB) interlayers, which prior work had shown difficulties in achieving good quality laminates, working with Pilkington North America. The second task dealt with a study of current lamination processes in the various laminate industries, and development of concepts for integrating RF lamination into new or existing processes. The third task explored the use of a non-destructive technique for analyzing laminate adhesion with the University of Illinois at Urbana-Champaign. The fourth task focused on developing concepts for curved glass lamination using RF lamination. The fifth and sixth tasks together comprised an analysis of laminate product markets, ranking for applicability and commercialization potential, and the development of commercialization strategies for those products. In addition, throughout the project as new experimental data and conventional process data were obtained, the benefits analysis of RF lamination was refined. The goals of the project described above were achieved, positioning RF lamination for the next stage growth envisioned in the original Industrial Grand Challenge proposal. Working with Pilkington North America, lamination of flat autoglass with PVB was achieved, meeting all 16 stringent industry tests. In particular, PVB laminates made with RF lamination passed environmental tests including the high temperature, 120 C bake test, without significant formation of bubbles (defects). The adhesion of PVB to glass was measured using the pummel method. Adhesion values ranging from 1 to 7 out of 10 were obtained. The significant process parameters affecting the environmental and adhesion performance were identified through a designed experiment. Pre-lamination process variables including PVB storage humidity and the de-airing process (vacuum or nip rolling) were significant, as well as the level of pressure applied to the laminate during the RF process. Analysis of manufacturing with RF lamination equipment, based on the processes developed indicated that 3 RF presses could replace a typical auto-industry autoclave to achieve equal or greater throughput with possibly less capital cost and smaller footprint. Concepts for curved lamination identifying castable molds for prototyping were developed, which allowed Ceralink to obtain commitment to begin curved tooling development. The project significantly helped to advance RF lamination past the feasibility and novelty stage and into the realm of commercial acceptance as a viable alternative to autoclaves. The demonstration of autoclave-quality autoglass produced in just 1 minute with RF lamination, with validation by Pilkington, has fueled industry motivation to seriously consider RF lamination. The industry and other contacts and outreach made in the study of laminate markets (including 3 technical publications and 5 conference presentations), has resulted in a recent surge in RF lamination activity.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

CTF Parallel Performance Improvements

CTF is a modernized version of COBRA-TF (Coolant Boiling in Rod Arrays-Two Fluid), which is a thermal hydraulic (T/H) sub-channel code based on a two-phase, two-fluid model that formulates the conservation equations of mass, energy, and momentum for three fields of vapor, continuous liquid, and entrained liquid droplets. Under the Consortium for Advanced Simulation of Light Water Reactors (CASL) program sponsored by the U.S. Department of Energy, CTF is being further developed and improved for modeling and simulation of light water reactors. The code improvements for predicting T/H responses of pressurized water reactor (PWR) cores are focused on its applications to specific challenge problems deemed significant to the industry, such as departure from nucleate boiling (DNB) and crud-induced power shift. The code is also being used for T/H feedback in normal operating condition depletions in PWR and boiling water reactor designs in the reactor core simulator, Virtual Environment for Reactor Applications Core Simulator (VERA-CS), being developed by CASL. CTF modifications under the CASL program include software optimization, new closure models, and parallelization for modeling full reactor core T/H responses. The purpose of this work was to improve the parallel performance of CTF. CTF was originally parallelized via a domain-decomposition strategy using the Message Passing Interface (MPI), in which the basis of a solution domain was a physical assembly in the model. In other words, a user who wanted to perform a parallel solution with CTF had to provide the code one processor per assembly in the model (e.g., 56 cores for a 56 assembly quarter-core model, or 193 cores for a 193 assembly full-core model). This design was rigid, demanding a very specific number of processors for a model; furthermore, when CTF was run in VERA-CS-which typically uses thousands of processors- many processors sat idle during the CTF solve because CTF was unable to use any more processors than there are physical assemblies. This was not necessarily a problem if the CTF execution speed was very fast, but the average time spent in a CTF solve for prototypical PWR operating conditions was significant (i.e., over 20 % of the simulation wall time was being spent in CTF for a standard core depletion simulation). Larger, more computationally intensive simulations performed in support of the CASL DNB challenge problem demonstrated a need for improvements in this original parallelization approach. The specific goal of this work was to allow CTF to use more processors than there are physical assemblies in the model, which would not only speed up CTF and improve the overall efficiency of VERA-CS but also give users more-flexible options for executing their simulations. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Non-linear Wire Rope Isolator Model to Enhance Transportation Simulation of Fragile Equipment

Abstract Introduction Wire rope isolators are often used as means of vibration isolation for the transportation of fragile machine equipment. When deployed as suspension systems in a transportation scenario, a simple spring–damper model is often used to predict the dynamic loads that act on the structure being transported. However, this simple model has proved to be too simplistic to be used in the development of an accurate numerical model that can predict the vibration levels experienced by the inner components of fragile equipment during its transportation. This paper describes the experimental tests conducted on a wire rope isolator used for the transportation of the prototype SSR1 cryomodule. Materials and methods A hysteretic Bouc–Wen model has been used to analytically describe the force–deformation relationship of the wire rope isolators. The developed model of the isolator has been implemented in a larger model to simulate the actual transportation of the prototype SSR1 cryomodule, a section of the new PIP-II linear accelerator under construction at Fermilab. A series of multibody dynamic simulations with rigid and flexible components was used to numerically determine the acceleration of some critical components. Results and conclusions An actual experimental transportation was simulated using two numerical models: the developed Bouc–Wen model and a conventional spring–damper model. It is shown how the Bouc–Wen formulation of the isolator characteristics drastically improves the correspondence between experimental and simulated results if compared to a spring–damper model, especially in the range of 0–30 Hz which is the most critical for transportation problems.

42 ENGINEERING↗

Optimal gas cooling with minimal aero-opticaldistortion for next generation high-average-power lasers (Progress report, Year 2)

Next-generation lasers that combine high-peak-power ultrashort pulses with high repetition rates have the potential to efficiently deliver the high-average-power outputs required for inertial fusion energy generation, laser-based particle acceleration, and to generate compact secondary x- and 𝛾-ray radiation sources, among others. The combination of long gain length with high surface-to-volume ratio to remove residual heat makes gas-cooled multi-slab amplifier heads an inherently aperture- and average power scalable technology that enables this new class of solid-state lasers, and their thermal management becomes the most pressing technical challenge. As the index-of refraction depends on the gas density, heat removal from the slab surfaces unavoidably entails scattering of propagated light from regions of high temperature fluctuations. The requirement to maximize convective heat extraction from the gain medium under the constraint of minimum optical aberration of the beam renders amplifier slab cooling a technological challenge at the intersection of aero-optics, fluid-mechanics and heat transfer. The goal of this research is to leverage computational fluid dynamics and aero optics simulations of different levels of fidelity to devise a numerical modeling and optimization framework for gas-cooled multi-slab amplifiers. The project will be conducted in close collaboration with the Advanced Photon Technologies Group at Lawrence Livermore National Laboratory, where a gas-cooled test stand for laser materials and thermal management structures will be developed and installed. The final goal of the collaborative effort is to manufacture and benchmark a physical prototype of an numerically optimized amplifier head design. Measurement data on solid-state and thermo-optical distortions will be used for the validation of the numerical models. The key technical challenge in this multi-objective design problem is that of balancing optimal heat removal with minimal optical distortion. To facilitate computationally efficient design optimization and, at the same time, deepen our basic understanding of the interaction of light with turbulence, a complementary study that combines high and low-fidelity flow simulations and aero-optical models is proposed. Along the lines of these two objectives and solution strategies, the project is organized into two thrusts.

42 ENGINEERING↗

Emerging Zero-Standby Solutions for Miscellaneous Electric Loads and the Internet of Things

Despite technical advances in efficiency, devices in standby continue to consume up to 16% of residential electricity. Finding practical, cost-effective reductions is difficult. While the per-unit power consumption has fallen, the number of units continuously drawing power continues to grow. This work reviews a family of technologies that can eliminate standby consumption in many types of electrical plug loads. It also investigates several solutions in detail and develops prototypes. First, burst mode and sleep transistors are established as building blocks for zero-standby solutions. This work then studies the application of two types of wake-up signals. The first is from an optical transmission, and is applicable to remote-controlled devices with a line-of-sight activation, such as set-top boxes, ceiling fans, and motorized curtains. The second is from a wake-up radio, and is applicable to any wireless products. No single technology will address all standby power situations; however, these emerging solutions appear to have broad applicability to save standby energy in miscellaneous plug loads.

42 ENGINEERING↗

The Unified Electrochemical Band Diagram Framework: Understanding the Driving Forces of Materials Electrochemistry

Recent work that establishes a picture of the driving forces that govern material transformations and degradation in electrochemical environments to enable the ab initio design of electrochemical materials is highlighted. Select prototype systems are used to describe how the interplay between materials properties such as crystal field splitting, band edge energies, surface termination, material length scale, dielectric constant, and isoelectric point, and electrolyte properties such as pH and ion type, impacts electrochemical behavior - i.e., redox potentials, reaction enthalpies, reactivity, and decoupled ionic/electronic processes. Ab initio modeling of charged defects and intercalants within the grand canonical unified electrochemical band-diagram (UEB) framework is shown to enable the quantitative prediction of electrochemical materials behavior. UEB combines electrochemical theory, charged defect theory, and band diagram descriptions and can be used both for materials discovery and development. First, a pedagogical description of the UEB framework is presented, and then the application of this framework to reveal mechanisms for high rate electronic charge storage in cation incorporated α.-MnO 2 and λ-MnO 2 , high desalination efficiency of thin-film NaMn 4 O 8 , and the flat charge/discharge profile of FePO 4 is reviewed. Finally, new prospects for the application of the UEB framework to electrolyte design, interfacial engineering, and catalysis are suggested.

36 MATERIALS SCIENCE↗

Demonstration and Feasibility Analyses of using the Dual-Purpose Canister Drain Pipe to Support the Filling Process

This report documents experiments that are being used to determine the feasibility of filling dual-purpose canisters (DPCs) using the existing drain pipe. Mercury was identified as a surrogate filler for the initial experiments. Oak Ridge National Laboratory’s Target Test Facility (TTF), which is a full-scale Spallation Neutron Source (SNS) prototypical mercury loop, is being used for the planned pipe experiments using mercury. The pipe experiments were divided into two phases to provide a separate effects approach to the problem and to allow for development of system scalability. The first phase included taking strain measurements in a short length pipe, as well as measurements of flow-induced vibration. The second phase consists of the design and construction of a separated mercury flow loop capable of hosting exchangeable test sections and more localized instrumentation. Data acquisition of Phase I was performed during this reporting time period, and subsequent data reduction and data analysis will be performed in the future.

36 MATERIALS SCIENCE↗

Direct Subsurface Measurements through Precise Micro Drilling

Wellbore integrity is a significant problem in the U.S. and worldwide, which has serious adverse environmental and energy security consequences. Wells are constructed with a cement barrier designed to last about 50 years. Indirect measurements and models are commonly used to identify wellbore damage and leakage, often producing subjective and even erroneous results. The research presented herein focuses on new technologies to improve monitoring and detection of wellbore failures (leaks) by developing a multi-step machine learning approach to localize two types of thermal defects within a wellbore model, a prototype mechatronic system for automatically drilling small diameter holes of arbitrary depth to monitor the integrity of oil and gas wells in situ, and benchtop testing and analyses to support the development of an autonomous real-time diagnostic tool to enable sensor emplacement for monitoring wellbore integrity. Each technology was supported by experimental results. This research has provided tools to aid in the detection of wellbore leaks and significantly enhanced our understanding of the interaction between small-hole drilling and wellbore materials.

42 ENGINEERING↗

Thermal characteristics of air flow cooling in the lithium ion batteries experimental chamber

A battery pack prototype has been designed and built to evaluate various air cooling concepts for the thermal management of Li-ion batteries. The heat generation from the Li-Ion batteries was simulated with electrical heat generation devices with the same dimensions as the Li-Ion battery (200 mm x 150 mm x 12 mm). Each battery simulator generates up to 15W of heat. There are 20 temperature probes placed uniformly on the surface of the battery simulator, which can measure temperatures in the range from -40 C to +120 C. The prototype for the pack has up to 100 battery simulators and temperature probes are recorder using a PC based DAQ system. We can measure the average surface temperature of the simulator, temperature distribution on each surface and temperature distributions in the pack. The pack which holds the battery simulators is built as a crate, with adjustable gap (varies from 2mm to 5mm) between the simulators for air flow channel studies. The total system flow rate and the inlet flow temperature are controlled during the test. The cooling channel with various heat transfer enhancing devices can be installed between the simulators to investigate the cooling performance. The prototype was designed to configure the number of cooling channels from one to hundred Li-ion battery simulators. The pack is thermally isolated which prevents heat transfer from the pack to the surroundings. The flow device can provide the air flow rate in the gap of up to 5m/s velocity and air temperature in the range from -30 C to +50 C. Test results are compared with computational modeling of the test configurations. The present test set up will be used for future tests for developing and validating new cooling concepts such as surface conditions or heat pipes.

25 ENERGY STORAGE↗

Design and Engineering of LUPIN: A Test-Bed Radiofrequency Ion Source for Enhanced Neutral Beam Injection on DIII-D

The Large, Uniform Plasma for Ionizing Neutrals (LUPIN) is an RF inductively coupled plasma (ICP) chamber for demonstrating plasma performance of an RF ICP positive ion source upgrade for the DIII-D Neutral Beam Injection (NBI) system. LUPIN will be used to investigate ion source physics, including neutral gas dynamics, plasma density uniformity, interactions with Faraday shields, and power coupling to novel RF antenna designs. LUPIN has an RF generator capable of delivering 20 kW of power at 2 MHz, which is coupled into a cylindrical quartz vessel measuring 20 cm in length and 10 cm in radius. This configuration matches the power density requirements for a full-scale ion source. Target hydrogen and deuterium plasma densities exceeding 10 18 m -3 would relate to extracted ion current densities of 2100 A/m 2 for 10 s. Vacuum conductance and gas flow calculations predict a maximum achievable neutral gas flow rate of 1675 Pa·L/s at 5 Pa of He, which mimics the gas flow of the DIII-D NBI system. Designs have been developed for an internal Faraday shield to mitigate heat flux and ion sputtering on the dielectric vessel. Thermomechanical finite element simulations demonstrated the Faraday shield design to be capable of withstanding anticipated heat loads from worst-case operation scenarios. Results of upcoming experimental investigations on LUPIN will guide the design of a full-scale prototype for DIII-D integration.

Faraday shield↗

Uncertainty quantification in scientific machine learning: Methods, metrics, and comparisons

Neural networks (NNs) are currently changing the computational paradigm on how to combine data with mathematical laws in physics and engineering in a profound way, tackling challenging inverse and ill-posed problems not solvable with traditional methods. However, quantifying errors and uncertainties in NN-based inference is more complicated than in traditional methods. This is because in addition to aleatoric uncertainty associated with noisy data, there is also uncertainty due to limited data, but also due to NN hyperparameters, overparametrization, optimization and sampling errors as well as model misspecification. Although there are some recent works on uncertainty quantification (UQ) in NNs, there is no systematic investigation of suitable methods towards quantifying the total uncertainty effectively and efficiently even for function approximation, and there is even less work on solving partial differential equations and learning operator mappings between infinite-dimensional function spaces using NNs. In this work, we present a comprehensive framework that includes uncertainty modeling, new and existing solution methods, as well as evaluation metrics and post-hoc improvement approaches. Further, to demonstrate the applicability and reliability of our framework, we present an extensive comparative study in which various methods are tested on prototype problems, including problems with mixed input-output data, and stochastic problems in high dimensions. In the Appendix, we include a comprehensive description of all the UQ methods employed. Further, to help facilitate the deployment of UQ in Scientific Machine Learning research and practice, we present and develop in [1] an open-source Python library (github.com/Crunch-UQ4MI/neuraluq), termed NeuralUQ, that is accompanied by an educational tutorial and additional computational experiments.

11 physics-informed neural networks↗

Multi-Scale, Multi-Physics Membrane Technology

Our objectives for this 10 week feasibility study were to gain an initial theoretical understanding of the numerical issues involved in modeling fluid-structure interface problems and to develop a prototype software infrastructure based on deforming composite grids to test the new approach on simple problems. For our first test case we considered a two-dimensional fluid-solid piston problem in which one half of the domain is occupied by fluid and the other half by a solid. We determined the exact solution to this problem using the method of characteristics and d'Alembert's solution to the wave equation. We solved this problem using our new numerical approximations and verified the results compared to the exact solution. As a second test case we considered a two dimensional problem consisting of a shock in a fluid that strikes a cylindrically shaped solid.

42 ENGINEERING↗