Search NASA⌕ Search

SEARCH · Search NASA

Results for “Exp”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Effective equations and the inverse cascade theory for Kolmogorov flows

We study the two dimensional Kolmogorov flows in the limit as the forcing frequency goes to infinity. Direct numerical simulation indicates that the low frequency energy spectrum evolves to a universal kappa (exp -4) decay law. We derive effective equations governing the behavior of the large scale flow quantities. We then present numerical evidence that with smooth initial data, the solution to the effective equation develops a kappa (exp -4) type singularity at a finite time. This gives a convenient explanation for the kappa (exp -4) decay law exhibited by the original Kolmogorov flows.

Weinan, E.↗

Comparison of a two-dimensional adaptive-wall technique with analytical wall interference correction techniques

A two dimensional airfoil model was tested in the adaptive wall test section of the NASA Langley 0.3 meter Transonic Cryogenic Tunnel (TCT) and in the ventilated test section of the National Aeronautical Establishment Two Dimensional High Reynold Number Facility (HRNF). The primary goal of the tests was to compare different techniques (adaptive test section walls and classical, analytical corrections) to account for wall interference. Tests were conducted over a Mach number range from 0.3 to 0.8 at chord Reynolds numbers of 10 x 10(exp 6), 15 x 10(exp 6), and 20 x 10(exp 6). The angle of attack was varied from about 12 degrees up to stall. Movement of the top and bottom test section walls was used to account for the wall interference in the HRNF tests. The test results are in good agreement.

Mineck, Raymond E.↗

Perspectives on high temperature superconducting electronics

The major challenges in making high temperature superconducting (HTSC) electronics viable are predominantly materials problems. Unlike their predecessors, the metal oxide-based superconductors are integratable with other advanced technologies such as opto-electronics and micro-electronics. The materials problems to be addressed relate to the epitaxial growth of high quality films, highly oriented films on non-lattice matched substrates, heterostructures with atomically sharp interfaces of junctions and other novel devices, and the processing of these films with negligible deterioration of the superconducting properties. These issues are illustrated with results based on films prepared in-situ by a pulsed laser deposition process. Films with zero-transition temperatures of 90 K and critical current densities of 5 x 10(exp 6) A/sq cm at 77 K have been prepared by this technique. Ultra-thin films, less than 100 A show T(sub c) is greater than 80 K, supporting the idea of two-dimensional transport in these materials. By the use of appropriate buffer layers, films with T(sub c) of 87 K and J(sub c) of 6 x 10(exp 4) A/sq cm were fabricated on silicon substrates. Submicron structures with J(sub c) is greater than 2 x 10(exp 7) at 10 K were fabricated. Results on nonlinear switching elements, IR detectors, and microwave studies will be briefly summarized.

Venkatesan, T.↗

GRIS observations of the galactic center and the gamma ray galactic diffuse continuum

On two flights in 1988, the Gamma-Ray Imaging Spectrometer (GRIS) discovered the galactic center in a high state (greater than 1 x 10(exp -3) ph/(sq cm sec)) of positron annihilation line emission (511 keV) after nearly a decade of failed attempts to confirm the exciting early results of balloon and satellite instruments. These two flights represented the first flights of a new generation of high resolution germanium spectrometers designed to achieve significantly greater sensitivity for astrophysical observations. During the fall flight, an observation of the galactic plane at 335 degrees longitude was also performed. This observation showed a very low level of 511 keV emission (2 +/- 1 x 10(exp -4) ph/(sq cm sec)), confirming the galactic center origin of the line, and a high level of hard x-ray and gamma-ray continuum emission (1 x 10(exp -4) ph/(sq cm sec keV) at 100 keV), which we attribute to galactic diffuse emission. Improved fits to the spectrum of the galactic center are presented with the proposed diffuse component subtracted. We conclude that our galactic center continuum spectrum is consistent with the sum of the 1E1740.7-2942 spectrum observed by SIGMA/GRANAT and our 1 = 335 degree galactic plane spectrum. The predicted diffuse flux should be easily measurable by the Oriented Scintillation Spectrometer Experiment (OSSE) experiment on the Gamma Ray Observatory (GRO).

Tueller, J.↗

Temperature effects on high strain rate properties of graphite/epoxy composites

A unidirectional graphite epoxy material (AS4/3501-6) was characterized at strain rates ranging from 5 x 10(exp 6) s(exp -1) to 5(exp -1), at room temperature and at 128 C. Results are presented in the form of stress-strain curves to failure. The longitudinal properties remain nearly unchanged with strain rate and temperature. The transverse modulus increases with strain rate but decreases with temperature. The transverse strength and transverse ultimate tensile strain have a positive rate sensitivity at low rates, which changes to negative at intermediate rates and returns to positive rate sensitivity at the highest rates tested. A temperature-time equivalence principle was applied and master curves were obtained for the transverse mechanical properties. The in-plane shear modulus and in-plane shear strength have a positive rate sensitivity. The ultimate intralaminar shear strain has a positive rate sensitivity at low rates, which changes to negative at high rates. At the elevated temperature of 128 C, the ultimate shear strain is 25 to 30 percent higher than the room temperature value, but its strain rate dependence is moderate.

Yaniv, G.↗

The electrical conductivities of the DSS-13 beam-waveguide antenna shroud material and other antenna reflector surface materials

A significant amount of noise temperature can potentially be generated by currently unknown dissipative losses in the beam waveguide (BWG) shroud. The amount of noise temperature contribution from this source is currently being studied. In conjunction with this study, electrical conductivity measurements were made on samples of the DSS-13 BWG shroud material at 8.420 GHz. The effective conductivities of unpainted and painted samples of the BWG shroud were measured to be 0.01 x 10(exp 7) and 0.0036 x 10(exp 7) mhos/m, respectively. This value may be compared with 5.66 x 10(exp 7) mhos/m for high conductivity copper.

Otoshi, T. Y.↗

A nanoradian differential VLBI tracking demonstration

The shift due to Jovian gravitational deflection in the apparent angular position of the radio source P 0201+113 was measured with very long baseline interferometry (VLBI) to demonstrate a differential angular tracking technique with nanoradian accuracy. The raypath of the radio source P 0201+113 passed within 1 mrad of Jupiter (approximately 10 Jovian radii) on 21 Mar. 1988. Its angular position was measured 10 times over 4 hours on that date, with a similar measurement set on 2 Apr. 1988, to track the differential angular gravitational deflection of the raypath. According to general relativity, the expected gravitational bend of the raypath averaged over the duration of the March experiment was approximately 1.45 nrad projected onto the two California-Australia baselines over which it was measured. Measurement accuracies on the order of 0.78 nrad were obtained for each of the ten differential measurements. The chi(exp 2) per degree of freedom of the data for the hypothesis of general relativity was 0.6, which suggests that the modeled dominant errors due to system noise and tropospheric fluctuations fully accounted for the scatter in the measured angular deflections. The chi(exp 2) per degree of freedom for the hypothesis of no gravitational deflection by Jupiter was 4.1, which rejects the no-deflection hypothesis with greater than 99.999 percent confidence. The system noise contributed about 0.34 nrad per combined-baseline differential measurement and tropospheric fluctuations contributed about 0.70 nrad. Unmodeled errors were assessed, which could potentially increase the 0.78 nrad error by about 8 percent. The above chi(exp 2) values, which result from the full accounting of errors, suggest that the nanoradian gravitational deflection signature was successfully tracked.

Treuhaft, R. N.↗

Direct numerical simulations of stably-stratified sheared turbulence: Implications for oceanic mixing

Direct numerical simulations of the time evolution of homogeneous stably stratified turbulent shear flows have been performed for several Richardson numbers Ri and Reynolds numbers R(sub lambda) in earlier works. The results show excellent agreement with length scale models developed from laboratory experiments to characterize oceanic turbulence. When the Richardson number Ri is less than the stationary value Ri(sub s), the turbulence intensity grows at all scales, and the growth rate appears to be a function of Ri. The size of the vertical density inversions also increases. On the other hand, when Ri is greater than or equal to Ri(sub s) the largest turbulent eddies become vertically constrained by buoyancy when the Ellison (turbulence) scale L(sub E) and the Ozmidov (buoyancy) scale L(sub O) are equal. At this point, the mixing efficiency is maximal and corresponds to a flux Richardson number R(sub f) = 0.20. The vertical mass flux becomes counter-gradient when epsilon = 19(nu)N(exp 2) and vertical density overturns are suppressed in less than half a Brunt-Vaisala period. The results of the simulations were also recast in terms of the Hydrodynamic Phase Diagram introduced in fossil turbulence models. The so-called point of fossilization occurs when epsilon = 4DCN(exp 2); Gibson proposed 13DCN(exp 2). This value is in agreement with indirect laboratory observations and field observations. Finally, the validity of the steady-state models to estimate vertical eddy diffusivities in the oceanic thermocline is discussed.

Itsweire, E. C.↗

Water vapor variance measurements using a Raman lidar

Because of the importance of atmospheric water vapor variance, we have analyzed data from the NASA/Goddard Raman lidar to obtain temporal scales of water vapor mixing ratio as a function of altitude over observation periods extending to 12 hours. The ground-based lidar measures water vapor mixing ration from near the earth's surface to an altitude of 9-10 km. Moisture profiles are acquired once every minute with 75 m vertical resolution. Data at each 75 meter altitude level can be displayed as a function of time from the beginning to the end of an observation period. These time sequences have been spectrally analyzed using a fast Fourier transform technique. An example of such a temporal spectrum obtained between 00:22 and 10:29 UT on December 6, 1991 is shown in the figure. The curve shown on the figure represents the spectral average of data from 11 height levels centered on an altitude of 1 km (1 plus or minus .375 km). The spectra shows a decrease in energy density with frequency which generally follows a -5/3 power law over the spectral interval 3x10 (exp -5) to 4x10 (exp -3) Hz. The flattening of the spectrum for frequencies greater than 6x10 (exp -3) Hz is most likely a measure of instrumental noise. Spectra like that shown in the figure are calculated for other altitudes and show changes in spectral features with height. Spectral analysis versus height have been performed for several observation periods which demonstrate changes in water vapor mixing ratio spectral character from one observation period to the next. The combination of these temporal spectra with independent measurements of winds aloft provide an opportunity to infer spatial scales of moisture variance.

Evans, K.↗

Infrared properties of Titan's clouds and aerosols

Using Voyager 1 Infrared Interferometer Spectrometer (IRIS) data, the infrared properties of Titan's north polar hood continuum were deduced. Stratospheric opacities were found to increase monotonically with wavenumber between 250 and 600/cm. The increase becomes more extreme with decreasing altitude; this behavior is consistent with a photochemical aerosol overlying layers of condensated organics lower down. Stratospheric optical thicknesses of order 0.1 were found at 600/cm, which became smaller as the wavelength decreased. An aerosol mass mixing ratio approximately 6 x 10 exp -8 and a mass flux approximately 10 exp -14 g/sq cm/s was inferred at 160 km. The column abundance for condensed C4N2 was found to exceed that for the vapor by a factor of 30 or more. An upper limit of 4 x 10 exp -10 was inferred for the mole fraction of gaseous C4N2.

Samuelson, Robert E.↗

Does UV instrumentation effectively measure ozone abundance?

Measurements of O3 on Mars provide significant information about the chemistry and composition of the atmosphere, including long-term changes. The most extensive and accurate data were inferred from the Mariner 9 UV spectrometer experiment. Mars O3 shows strong seasonal and latitudinal variation, with column abundances ranging from 0.2 microns at equatorial latitudes to 60 microns over the northern winter polar latitudes (1 micron-atm is a column abundance of 2.689 x 10(exp 15) molecules cm(exp-2)). The Mariner 9 UV spectrometer scanned from 2100 to 3500 Angstroms in one of its two spectral channels every 3 seconds with a spectral resolution of 15 Angstroms and an effective field-of-view of approximately 300 km(exp 2). Measurements were made for almost half a Martian year, with winter and spring in the Northern Hemisphere and summer and fall in the Southern Hemisphere. The detectability limit of the spectrometer was approximately 3 microns of ozone. The UV spectrometer on Mariner 9 was incapable of penetrating the dust during dust storms; the single-scattering albedo and phase function of airborne dust and cloud ice are not known to the degree required to extract the small UV signal reflected up from near the surface. The reflectance spectroscopy technique would also have difficulty detecting the total column abundance of O3 in cases where large dust abundances exist together with the polar hood, especially at high latitudes where large solar zenith angles magnify those optical depths; yet these cases would contain the maximum O3, based on theoretical results. It is quite possible that the maximum O3 column abundance observed by Mariner 9 of 60 microns is common. In fact, larger quantities may exist in some of the colder areas with optically thick clouds and dust. As the Viking period often had more atmospheric dust loading than did that of Mariner 9, the reflectance spectroscopy technique may even have been incapable of detecting the entire O3 column abundance during much of the Mars year that Viking observed, particularly at high latitudes.

Lindner, Bernhard Lee↗

Voyager 2 electron observations in the magnetosphere of Neptune

This paper describes electron data obtained during the Neptune encounter by the Voyager 2 plasma science experiment. The densities and temperatures of low-energy (10-5950 eV) electrons and the electrostatic potential of the spacecraft near Neptune are derived. The data indicate that the escape of charged particles from Triton and the local ionization of atoms in the neutral torus originating from Triton are the major plasma sources. It is inferred that this neutral torus of hydrogen atoms has a density of about 300/cu cm and an inner boundary at 8 R(N). The data near Neptune exhibit signatures suggesting that both precipitation into Neptune's atmosphere and ring absorption are important plasma loss mechanisms. Plasma transport in the magnetosphere appears to be very fast; the diffusion coefficient is 1 x 10 exp -7 L exp 3 R(N) exp 2/sec.

Zhang, Ming↗

The Galactic center radio source shines below the Compton limit

Absence of refractive scintillation of Sgr A*, the Galactic center radio source, at 1.3 and 0.8 mm wavelengths places an observational limit of brightness temperature of below 0.5 x 10 exp 12 K on the source. This is less than the maximum brightness of an incoherently synchrotron-emitting plasma, 10 exp 12 K, known as the Compton limit. The refractive scintillations expected, due to strong broadening of the source by the interstellar plasma, are observed by Zhao et al. at decimeter wavelengths. It has proven to be impossible to observe them at 1.3 and 0.8 mm wavelengths over time spans between 0.1 s and 24 hr. Such scintillations are quenched by source size greater than about 0.1 AU, or, equivalently, less than 0.5 x 10 exp 12 K for Sgr A*, at 0.8 mm wavelength. The scintilations would also require fluctuations with scale sizes of 0.1 AU in the scattering plasma, moving across the line of sight at velocities above about 100 km/s. The plasma that scatters Sgr A* satisfies the latter two conditions, and the absence of scintillations is due to the size of the source. This observation strengthens the identification of Sgr A* as a quiescent galactic nucleus.

Gwinn, C. R.↗

Installing scientific instruments into a cold LHe dewar - The Gravity Probe B approach

Gravity Probe B is an orbital test of Einstein's general theory of relativity using gyroscopes. The precession of the gyroscopes will measure both the geodetic effect (6.6 arcsec/yr) through the curved space-time surrounding the earth and the motional effect (0.042 arcsec/yr) due to the rotating earth dragging space-time around with it. To achieve the extraordinary accuracies needed to measure these small precessions, it is necessary to have the gyroscopes operating in the following environments: a vacuum of less than 10 exp -10 torr; an acceleration level of less than 10 exp -10 g's; a magnetic field of less than 10 exp -7 gauss; and a temperature near 2 K. This paper discusses designs that allow scientific instruments to be installed into a dewar at 4.2 K. Methods for structurally supporting the instruments, transferring heat across joints at low temperature in vacuum, and excluding air during the insertion process are discussed. The structural support method is designed for Shuttle launch loads.

Parmley, Richard T.↗

Mantle viscosity - A comparison of models from postglacial rebound and from the geoid, plate driving forces, and advected heat flux

Models of the radial variation of effective viscosity inferred from the earth's response to surface loads associated with Pleistocene deglaciation are compared to structures inferred from models of geodynamic phenomena associated with convection: the geoid, plate-driving forces, and advected heat flux. While observations of the earth's response to surface loads do not have sufficient resolution to justify more than two viscous layers, adequately matching the observed long-wavelength geoid anomalies associated with density contrasts in the lower mantle (inferred from seismic tomography) and in the upper mantle (inferred from a model of subducted slabs) requires more structure. It is possible to explain the geoid, observed plate velocities, the advected heat flux in the lower mantle, and relative sea-level variations in oceanic regions, all with a mantle with a high-viscosity/elastic lid, an asthenospheric channel of 2 x 10 exp 19 Pa s from 100 to 400-km depth, a 6 x 10 exp 20 Pa s transition zone, and a lower mantle of 6 x 10 exp 21 Pa s. The uplift history of Australia, Fennoscandia, and Laurentia can be explained with an asthenospheric viscosity less than a factor of 10 higher. Lateral variations in lower mantle viscosity are not required. Transient creep appears to be unimportant for the recent response-to-surface loads from Pleistocene deglaciation.

Hager, Bradford H.↗

A model of the formation of high-salinity shelf water on polar continental shelves

This study presents a model of the flow and salinity fields forced by sea-surface salinity flux and wind stress curl and examines the processes that create High-Salinity Shelf Water (HSSW). To investigate the relative effects of wind stress and buoyancy forcing in HSSW production, the polynya freezing rate in the model is varied from 0.0 to 0.30 m/d, and the Ekman pumping derived from the wind stress curl is varied independently from 0.0 to 1.8 x 10 exp 6 m/s. The Ekman pumping was found to control the magnitude of the circulation, while the polynya freezing rate controlled the extent of salinization in the shelf water. The flux of HSSW increases linearly with increasing Ekman pumping above 0.3 x 10 exp -6 m/s. The modeled flux of HSSW and the flux of derived Botttom Water for the present estimates of the forcings (a peak freezing rate of 0.10 m/d and Ekman pumping of 0.2 x 10 exp -6 m/s) agree with the fluxes inferred from physical and chemical observations in the deep Weddel Sea by oceanographic field programs.

Grumbine, Robert W.↗

The influence of dynamics on two-dimensional model results - Simulations of C-14 and stratospheric aircraft NO(x) injections

The influence of dynamics on model results is investigated via a 2D photochemical model. Three representations of atmospheric transport are tested in order to simulate total ozone and C-14 amounts after nuclear tests in the early 1960s. Three scenarios of NO(x) injections from a proposed fleet of stratospheric aircraft and their effects on ozone are simulated. The three dynamical formulations used are Dynamics A, a base dynamics used in previous work with this model; Dynamics B, a strong circulation dynamics discussed by Jackman et al. (1989); and Dynamics C, the dynamics used by Shia et al. (1989). The advective component of the stratosphere to the troposphere mass exchange rate is largest for Dynamics B (5.8 x 10 exp 17 kg/yr) and smallest for Dynamics C (1.4 x 10 exp 17 kg/yr), with the advective strat/trop exchange rate for Dynamics A (2.4 x 10 exp 17 kg/yr) being these two extremes. Ozone depletion from NO(x) injections of stratospheric aircraft showed a strong sensitivity to dynamics.

Jackman, Charles H.↗

Optical absorption by free holes in heavily doped GaAs

Optical absorption in p-type GaAs with hole concentrations between 10 exp 19 and 10 exp 20/cu cm has been measured for wavelengths between 2 and 20 microns and compared with results of theoretical calculations. In contrast to previous measurements at lower doping levels, the occupied hole states are far from the zone center, where the heavy- and light-hole bands become parallel. This gives rise to a large joint density of states for optical transitions. It is found that the overall magnitude of the observed absorption is explained correctly by the theory, with both the free-carrier (indirect) and the inter-valence-band (direct) transitions contributing significantly to the total absorption. The strength of the absorption (a about 20,000/cm for N(A) = 5 x 10 exp 19/cu cm) is attractive for long-wavelength infrared-detector applications.

Huberman, M. L.↗