Search NASA⌕ Search

SEARCH · Search NASA

Results for “Operating Mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Seamless Transition of Critical Infrastructures using Droop Controlled Grid-forming Inverters

Seamless recovery of power to critical infrastructures, after grid failure, is a crucial need arising in scenarios that are increasingly becoming more frequent. Here, this article proposes a seamless transition strategy using a single and unified mode-dependent droop controlled grid-forming inverters. The control strategy achieves the following objectives: 1) regulates the output active and reactive power by the droop-controlled inverters to a desired value while operating in on-grid mode; 2) seamless transition and recovery of power injections into the load after grid failure by inverters that operates in grid-forming mode all the time; 3) requires only a single bit of information on the grid/network status for the mode transition. A framework for assessing the stability of the system and to guide the choice of parameters for controllers is developed using control-oriented modeling. A controller hardware-in-the-loop-based real-time simulation study on a test system based on the realistic electrical network of a commercial-scale medical center is conducted for initial prototyping of the control strategy. A hardware experiment is conducted with two 3 - $\phi$, 480 -V, 125 -kVA grid-forming inverters, a 3 - $\phi$, 480 -V, 270 -kVA grid simulator, a physical grid switch, and a physical load bank. The experimental data establishes the effectiveness of the always grid-forming operation and control of inverters in meeting power delivery objectives when on-grid and off-grid under various kinds of loads and scenarios while minimizing transients during transitions. Furthermore, performance comparison with existing strategies showcases the advantage of the proposed strategy.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Multi-mode advanced combustion engine with supervisory control

An engine system uses data associated with at least one operating condition of an engine to set the engine system to an AI mode when the engine is in an SI mode 1) within first operating condition limits, and 2) when a rate of change of a first operating condition is within rate of change limits, maintain the engine system in the SI mode when the engine is outside of first operating condition limits or when the rate of change of the first operating condition is not within rate of change limits, set the engine system to the SI mode when the engine is in the AI mode outside second operating condition limits, and maintain the engine system in the AI mode when the engine is within second operating condition limits, wherein the second operating condition limits are different from the first operating condition limits.

42 ENGINEERING↗
DOE OSTI2018

Three Way Catalyst-Selective Catalytic Reduction Aftertreatment System Evaluation for a Lean Burn Gasoline Engine Operating in Homogenous Charge Compression Ignition, Spark-Assisted Compression Ignition, and Spark-Ignited Combustion Modes

Low temperature and dilute homogenous charge compression ignition (HCCI) and spark-assisted compression ignition (SACI) can improve fuel efficiency and reduce engine-out NO x emissions, especially during lean operation. However, under lean operation, these combustion modes are unable to achieve Environmental Protection Agency (EPA) Tier 3 emissions standards without the use of lean aftertreatment. The three way catalyst (TWC)-SCR lean aftertreatment concept investigated in this work uses periodic-rich operation to produce NH 3 over a TWC to be stored on a selective catalytic reduction (SCR) catalyst for NO x conversion during subsequent lean operation. Experiments were performed with a modified 2.0 L gasoline engine that was cycled between lean HCCI and rich SACI operation and between lean and rich spark-ignited (SI) combustion to evaluate NO x conversion and fuel efficiency benefits. Different lambda values during rich operation and different times held in rich operation were investigated. Results are compared to a baseline case in which the engine is always operated at stoichiometric conditions. SCR system calculations are also presented to allow for comparisons of system performance for different levels of stored NH 3 . With the configuration used in this study, lean/rich HCCI/SACI operation resulted in a maximum NO x conversion efficiency of only 10%, while lean/rich SI operation resulted in a maximum NO x conversion efficiency of 60%. If the low conversion efficiency of HCCI/SACI operation could be improved through higher brick temperatures or additional SCR bricks, calculations indicate that TWC-SCR aftertreatment has the potential to provide attractive fuel efficiency benefits and near-zero tailpipe NO x . Calculated potential fuel efficiency improvement relative to stoichiometric SI is 7–17% for lean/rich HCCI/SACI with zero tailpipe NO x and -1 to 5% for lean/rich SI with zero tailpipe NO x emissions. Although the previous work indicated that the use of HCCI/SACI increases the time for NH 3 to start forming over the TWC during rich operation, reduces NH 3 production over the TWC per fuel amount, and increases NH 3 slip over the SCR catalyst, if NO x conversion efficiency could be enhanced, improvements in fuel efficiency could be realized while meeting stringent tailpipe NO x standards.

Engineering↗
DOE OSTI2016

POWER RECYCLING OF BURST-MODE LASER PULSES FOR LASER PARTICLE INTERACTIONS

A number of laser-particle interaction experiments such as the laser assisted hydrogen ion beam stripping or X-/ -ray generations via inverse-Compton scattering involve light sources operating in a burst mode to match the tem-poral structure of the particle beam. To mitigate the laser power challenge, it is important to make the interaction inside an optical cavity to recycle the laser power. In many cases, conventional cavity locking techniques will not work since the burst normally has a very small duty factor and low repetition rate and it is impossible to gen-erate an effective control signal. This work reports on the development of a doubly-resonant optical cavity scheme and its locking techniques that enables a simultaneous resonance of two laser beams with different spectra and/or temporal structures. We demonstrate that such a cavity can be used to recycle burst-mode ultra-violet laser pulses with arbitrary burst lengths and repetition rates.

burst mode laser↗
DOE OSTI2020

Spatiotemporal flame propagations, combustion and solid particle emissions from lean and stoichiometric gasoline direct injection engine operation

Increased particle number and mass emissions in gasoline direct injection (GDI) engines should require to investigate in-cylinder flame and combustion characteristics associated with primary source of particle emissions. In this article, in-cylinder spatiotemporal flame luminosity is quantitatively characterized to features combustion process and solid particle emissions from a GDI engine operating in two lean and one stoichiometric modes. Low- and high-steady state operating points were used to compare combustion strategies on flame development and emission characteristics. A fiber-optic sensor composed of eight measurement channels detected the flame front and the direction of the flame propagation in the combustion chamber. Solid particle emissions in the exhaust were measured using an engine exhaust particle sizer and a micro soot sensor. Results of the experiments showed that two lean combustion modes by injection strategies resulted in distinct combustion and flame development. Lean combustion modes generated high diffusion flame by burning stratified rich-mixture. Although the lean cases resulted in strong diffusion flames, the lean-homogeneous produced similar particle size distributions with the stoichiometric mode with high ash particles. Piston pool fires on the piston surface in the lean-stratified mode induced a large accumulation mode with high particle mass concentrations.

42 ENGINEERING↗
DOE OSTI2020

Performance study of the cross-flow Maisotsenko cycle in humid climate conditions

This paper presents a first numerical analysis of the cross-flow Maisotsenko cycle (M-Cycle) below dew-point evaporative cooler for humid climates with model including the water vapor condensation phenomenon. Proposed solution allows to cool ambient air below its dew-point temperature, by utilizing cooling energy in air extracted from the building, due to that it can be used as effective pre-cooling solution for traditional systems. Proposed unit has significant advantage over traditional counter and cross-flow units operating in heat recovery mode, hence it is almost insensitive on temperature of exhaust air. This is caused by effective pre-cooling of the exhaust air in its initial part. Operation in humid climates using cold extracted air results in condensation occurrence in the primary air channels, and hence partial dehumidification of the primary airflow (which allows to cool the air before its dew- point temperature). The Maisotsenko cycle exchanger used to recover heat in the air-conditioning system is compared with Maisotsenko exchanger that operates only on the ambient airflow and does not allow to recover heat from the exhaust airflow from a conditioned space. Achieved results showed that M-Cycle below dew-point air cooler can operate more effectively in humid climates than traditional cross-flow Maisotsenko cycle exchanger.

Condensation↗
DOE OSTI2014

Note: On the generation of sub-300 keV flash-X-rays using rod-pinch diode: An experimental investigation

Generation of flash X-rays (FXRs) at less than 500 keV is described with emphasis on experimental investigation. The pulser is a Tesla transformer-Water transmission line based pulsed power generator operating in double resonance mode to power a rod-pinch diode. The configuration of aspect ratio reported here falls much below the normally reported ratios for the rod-pinch diode operation. Experimental investigation at such low pulsed voltage has revealed “flowering” of the anode tip and “pitting” of the perspex window. A possible explanation in terms of Lorentz body force is discussed rather than the pinch mechanism generally suggested in literature. The experimental investigation for the FXR generation is corroborated by measuring the radiation dose using CaSO{sub 4} (Dy) thermo luminescent dosimeters.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2015

Ideas That Work! The Midnight Audit

The midnight audit provides valuable insight toward identifying opportunities to reduce energy consumption—insight that can be easily overlooked during the normal (daytime) energy auditing process. The purpose of the midnight audit is to observe after-hour operation with the mindset of seeking ways to further minimize energy consumption during the unoccupied mode and minimize energy waste by reducing unnecessary operation. The midnight audit should be used to verify that equipment is off when it is supposed to be, or operating in set-back mode when applicable. Even a facility that operates 2 shifts per day, 5 days per week experiences fewer annual hours in occupied mode than it does during unoccupied mode. Minimizing energy loads during unoccupied hours can save significant energy, which is why the midnight audit is an Idea That Works.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2018

Decomposition of Nonlinear Dynamical Systems Using Koopman Gramians

In this paper we propose a new Koopman operator approach for nonlinear model decomposition using Koopman gramians. We introduce Koopman operators and discuss the notion of a input-Koopman operator. We show how input-Koopman operators can be used to cast a nonlinear system into the classical state-space form, as well as conditions under which input and state observable functions are well separated. We extend an existing method of dynamic mode decomposition for learning Koopman operators from data known as deep dynamic mode decomposition, for systems with control or disturbances. We illustrate the accuracy of the method on learning an input-state separable Koopman operator for an example system, even when the underlying system exhibits mixed state-input terms. Finally, we introduce a nonlinear decomposition algorithm, based on Koopman gramians, that maximizes internal subsystem observability and disturbance rejection from unwanted noise in other subsystems. To relieve the NP-hardness of the decomposition problem, we derive a relaxation based on Koopman gramians and multi-way partitioning. We illustrate our algorithm on a swing dynamics model for a IEEE 39 bus and discuss our findings.

Learning, Control, Distributed Control, koopman op↗
DOE OSTI2017

First-principles study of crystallographic slip modes in ω-Zr

We use first-principles density functional theory to study the preferred modes of slip in the high-pressure ω phase of Zr. The generalized stacking fault energy surfaces associated with shearing on nine distinct crystallographic slip modes in the hexagonal ω-Zr crystal are calculated, from which characteristics such as ideal shear stress, the dislocation Burgers vector, and possible accompanying atomic shuffles, are extracted. Comparison of energy barriers and ideal shear stresses suggests that the favorable modes are prismatic < c >, prismatic-II <101¯0> and pyramidal-II < c+a >, which are distinct from the ground state hexagonal close packed α phase of Zr. Operation of these three modes can accommodate any deformation state. The relative preferences among the identified slip modes are examined using a mean-field crystal plasticity model and comparing the calculated deformation texture with the measurement. In conclusion, knowledge of the basic crystallographic modes of slip is critical to understanding and analyzing the plastic deformation behavior of ω-Zr or mixed α-ω phase-Zr.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Characterization of a dimer preparation method for nanoscale organic aerosol

Nanoscale dimers have application in studies of aerosol physicochemical properties such as aerosol viscosity. These particle dimers can be synthesized using the dual tandem differential mobility analyzer (DTDMA) technique, wherein oppositely charged particle streams coagulate to form dimers that can be isolated using electrostatic filtration. Although some characterization of the technique has been published, a detailed thesis on the modes and theory of operation has remained outside the scope of prior work. In this paper we present new experimental data characterizing the output DTDMA size distribution and the physical processes underlying its apparent modes. Key experimental limitations for both general applications and for viscosity measurements are identified and quantified in six distinct types of DTDMA experiments. The primary consideration is the production of an adequate number of dimers, which typically requires high mobility-selected number concentration in the range 25,000-100,000 cm -3 . The requisite concentration threshold depends upon the rate of spontaneous monomer decharging, which arises predominately from interactions of the aerosol with ionizing radiation within the coagulation chamber and is instrument location dependent. Lead shielding of the coagulation chamber reduced the first-order decharging constant from ~2.0 x 10 -5 s -1 to ~0.8 x 10 -5 s -1 in our laboratory. Dimer production at monomer diameters less than 40 nm is hindered by low bipolar charging efficiency. Results from the characterization experiments shed light on design considerations for general applications and for characterization of viscous aerosol phase transitions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Investigation of the transition from streamer to uniform ‘overvoltage’ mode of atmospheric air nanosecond-pulsed dielectric barrier discharge

A nanosecond-pulsed dielectric barrier discharge ignited in atmospheric air was studied by optical emission spectroscopy to investigate the time- and space-resolved development of the reduced electric field. The discharge operated in two distinct modes that correlate with the values of the applied electric field: non-uniform streamer regime and uniform breakdown regime. It is shown that the reduced electric field in the non-uniform mode corresponds to the propagation of cathode-directed streamers, while in uniform discharge both molecular nitrogen emission and the reduced electric field are uniformly distributed along the gap during the initial discharge development stage with corresponding lower reduced electric field values.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Landau Modes are Eigenmodes of Stellar Systems in the Limit of Zero Collisions

Abstract We consider the spectrum of eigenmodes in a stellar system dominated by gravitational forces in the limit of zero collisions. We show analytically and numerically using the Lenard–Bernstein collision operator that the Landau modes, which are not true eigenmodes in a strictly collisionless system (except for the Jeans unstable mode), become part of the true eigenmode spectrum in the limit of zero collisions. Under these conditions, the continuous spectrum of true eigenmodes in a collisionless system, also known as the Case–van Kampen modes, is eliminated. Furthermore, because the background distribution function in a weakly collisional system can exhibit significant deviations from a Maxwellian distribution function over long times, we show that the spectrum of Landau modes can change drastically even in the presence of slight deviations from a Maxwellian, primarily through the appearance of weakly damped modes that may be otherwise heavily damped for a Maxwellian distribution. Our results provide important insights for developing statistical theories to describe thermal fluctuations in a stellar system, which are currently a subject of great interest for N -body simulations as well as observations of gravitational systems.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Ultra-high dose rate FLASH irradiator at the radiological research accelerator facility

The Radiological Research Accelerator Facility has modified a decommissioned Varian Clinac to deliver ultra-high dose rates: operating in 9 MeV electron mode ( FLASH mode), samples can be irradiated at a Source-Surface Distance (SSD) of 20 cm at average dose rates of up to 600 Gy/s (3.3 Gy per 0.13 µs pulse, 180 pulses per second). In this mode multiple pulses are required for most irradiations. By modulating pulse repetition rate and irradiating at SSD = 171 cm, dose rates below 1 Gy/min can be achieved, allowing comparison of FLASH and conventional irradiations with the same beam. Operating in 6 MV photon mode, with the conversion target removed ( SuperFLASH mode), samples are irradiated at higher dose rates (0.2–150 Gy per 5 µs pulse, 360 pulses per second) and most irradiations can be performed with a single very high dose rate pulse. In both modes we have seen the expected inverse relation between dose rate and irradiated area, with the highest dose rates obtained for beams with a FWHM of about 2 cm and ± 10% uniformity over 1 cm diameter. As an example of operation of the ultra-high dose rate FLASH irradiator, we present dose rate dependence of dicentric chromosome yields.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Strong and almost strong modes of Floquet spin chains in Krylov subspaces

Integrable Floquet spin chains are known to host strong zero and π modes which are boundary operators that respectively commute and anticommute with the Floquet unitary generating stroboscopic time evolution, in addition to anticommuting with a discrete symmetry of the Floquet unitary. Thus the existence of strong modes implies a characteristic pairing structure of the full spectrum. Weak interactions modify the strong modes to almost strong modes that almost commute or anticommute with the Floquet unitary. Manifestations of strong and almost strong modes are presented in two different Krylov subspaces. One is a Krylov subspace obtained from a Lanczos iteration that maps the time evolution generated by the Floquet Hamiltonian onto dynamics of a single particle on a fictitious chain with nearest-neighbor hopping. The second is a Krylov subspace obtained from the Arnoldi iteration that maps the time evolution generated directly by the Floquet unitary onto dynamics of a single particle on a fictitious chain with longer-range hopping. While the former Krylov subspace is sensitive to the branch of the logarithm of the Floquet unitary, the latter obtained from the Arnoldi scheme is not. In this work, the effective single-particle models in the Krylov subspace are discussed, and the topological properties of the Krylov chain that ensure stable zero and π modes at the boundaries are highlighted. The role of interactions is discussed. Expressions for the lifetime of the almost strong modes are derived in terms of the parameters of the Krylov subspace, and are compared with exact diagonalization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Generation of Giant Amplitude Pulses in a Klystron Chaos Auto-Oscillator

The presented experimental results demonstrate that microwave pulses of giant amplitude are generated in a klystron generator operating in the self-excited mode of chaotic oscillations. The auto-oscillator is assembled using a noisetron scheme that contains two five-cavity floating-drift klystrons serially connected in a ring, one of which operates in the mode of linear signal amplification (the linear klystron) and the other works in the mode of nonlinear signal amplification (the nonlinear klystron). It is established that, at a certain value of the beam current of a nonlinear klystron, intermittency of chaos–chaos type is realized in the auto-oscillation system in the form of chaotic sequences of microwave pulses of giant amplitude formed over the chaotic amplitude background. This type of intermittency is caused by the amplitude bistability of the nonlinear floating-drift klystron.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2014

Edge-localized-modes in tokamaks

Edge-localized-modes (ELMs) are a ubiquitous feature of H-mode in tokamaks. When gradients in the H-mode transport barrier grow to exceed the MHD stability limit the ELM instability grows explosively, rapidly transporting energy and particles onto open field lines and material surfaces. Though ELMs provide additional particle and impurity transport through the H-mode transport barrier, enabling steady operation, the resulting heat flux transients to plasma facing surfaces project to large amplitude in future low collisionality burning plasma tokamaks. Measurements of the ELM heat flux deposition onto material surfaces in the divertor and main chamber indicate significant broadening compared to inter-ELM heat flux, with a timescale for energy deposition that is consistent with sonic ion flow and numerical simulation. Comprehensive ELM simulation is highlighting the important physics processes of ELM transport including parallel transport due to magnetic reconnection and turbulence resulting from collapse of the H-mode transport barrier. Encouraging prospects for ELM control and/or suppression in future tokamaks include intrinsic modes of ELM free operation, ELM triggering with frequent small pellet injection and the application of 3D magnetic fields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2014

Continuous Variable Cluster State Generation over the Optical Spatial Mode Comb

One way quantum computing uses single qubit projective measurements performed on a cluster state (a highly entangled state of multiple qubits) in order to enact quantum gates. The model is promising due to its potential scalability; the cluster state may be produced at the beginning of the computation and operated on over time. Continuous variables (CV) offer another potential benefit in the form of deterministic entanglement generation. This determinism can lead to robust cluster states and scalable quantum computation. Recent demonstrations of CV cluster states have made great strides on the path to scalability utilizing either time or frequency multiplexing in optical parametric oscillators (OPO) both above and below threshold. The techniques relied on a combination of entangling operators and beam splitter transformations. Here we show that an analogous transformation exists for amplifiers with Gaussian inputs states operating on multiple spatial modes. By judicious selection of local oscillators (LOs), the spatial mode distribution is analogous to the optical frequency comb consisting of axial modes in an OPO cavity. We outline an experimental system that generates cluster states across the spatial frequency comb which can also scale the amount of quantum noise reduction to potentially larger than in other systems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗