Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

On-board processing satellite network architecture and control study

For satellites to remain a vital part of future national and international communications, system concepts that use their inherent advantages to the fullest must be created. Network architectures that take maximum advantage of satellites equipped with onboard processing are explored. Satellite generations must accommodate various services for which satellites constitute the preferred vehicle of delivery. Such services tend to be those that are widely dispersed and present thin to medium loads to the system. Typical systems considered are thin and medium route telephony, maritime, land and aeronautical radio, VSAT data, low bit rate video teleconferencing, and high bit rate broadcast of high definition video. Delivery of services by TDMA and FDMA multiplexing techniques and combinations of the two for individual and mixed service types are studied. The possibilities offered by onboard circuit switched and packet switched architectures are examined and the results strongly support a preference for the latter. A detailed design architecture encompassing the onboard packet switch and its control, the related demand assigned TDMA burst structures, and destination packet protocols for routing traffic are presented. Fundamental onboard hardware requirements comprising speed, memory size, chip count, and power are estimated. The study concludes with identification of key enabling technologies and identifies a plan to develop a POC model.

Campanella, S. Joseph↗

A comparison of two independent measurements and analysis of jet aircraft flyover noise

Flyover noise measurements were made simultaneously by two groups. The measurements were made close to one another for the same flyover conditions and with similar measurement procedures, but with different acoustic equipment and personnel. Each group also independently processed the data in accordance with FAR 36 procedures, indluding corrections to reference meteorological, performance, and flight-path conditions. Measured and corrected data, from 24 controlled flyovers processed by both groups, are compared and the differences in the results obtained by the two groups are discussed. It is observed that the average value of the difference between the groups' measured acoustic descriptors (PNL, PNLTM, and EPNL) was less than or = 0.8 db; the average difference for the corrected descriptors (PNL, PNLTM, and EPNL) was less than or = 1.5 db. Causes of the differences were found to be mainly related to different spectrum extrapolation and preemphasis techniques used by the two groups.

Hosier, R. N.↗

Making Smaller Microshells From Refractory Metals

Tendency toward gas porosity exploited. Falling through drop tube, fine drops of molten metal lose heat to surroundings, forming hard shells around precipitated gas. Second heating/cooling cycle in drop tube of lower pressure lets gas expand. Process produces smaller shells in greater variety of materials than possible with such current processes as based on hollow-jet instability, dry-chemical blowing or fluid-droplet drying. Shell aspect ratio (ratio of radius to wall thickness) controllable. New process makes shells having diameters smaller than 100 micrometer. There are several candidate shell materials including refractory metals.

Lee, Mark C.↗

Thermal structure of neutral winds from young stellar objects

The physical processes that control the thermal structure of lightly ionized winds from cool protostars are discussed. Attention is concentrated on the hydrogen gas, and the heating, cooling, and chemical processes that affect the neutral and ionic species of atomic and molecular hydrogen are examined. Warm silicate dust may condense out of the cooling wind and may heat the gas through collisions. Singly ionized sodium atoms, which do not recombine for the mass-loss rates considered, set a lower limit to the ionization fraction in the wind. Magnetic fields, which are presumed to accelerate the wind, couple directly to the ionic component of the gas and transfer momentum and energy to the neutral component through collisions. This process of ambipolar diffusion is found to be the dominant source of heat input to the gas.

Ruden, Steven P.↗

Oceanic upper mixed layer depth determination by the use of satellite data

A method has been developed to determine the oceanic daily mean mixed layer depth from satellite observations and a mixed layer thermal inertia (MLTI) model. The algorithms were developed to use remotely-sensed values of sea surface temperature, albedo, and surface wind speeds to calculate the thermal inertia and to predict changes in subsurface diurnal mixed layer depth. The MLTI model, based on a mixed layer model of the upper ocean, has been used to simulate the diurnal mixing process and thermal inertia distribution in the Sargasso Sea around 34 deg N, 70 deg W. Sea surface temperature and albedo have been obtained from the NOAA7-AVHRR images. Surface wind speeds have been derived from the Scanning Multichannel Microwave Radiometer (SMMR) aboard Nimbus 7. Image processing was performed for images gathered between June and July 1982. The daily mean mixed layer depths predicted by the MLTI model agree well with data gathered at the LOTUS mooring located in the Sargasso Sea. This suggests that vertical mixing is the dominant physical process that controls the thermal inertia distribution in the midocean, far from major current systems, and that remote sensing is a promising tool to study such upper ocean processes.

Yan, Xiao-Hai↗

Antenna Linear-Quadratic-Gaussian (LQG) Controllers: Properties, Limits of Performance, and Tuning Procedure

Wind gusts are the main disturbances that depreciate tracking precision of microwave antennas and radiotelescopes. The linear-quadratic-Gaussian (LQG) controllers - as compared with the proportional-and-integral (PI) controllers significantly improve the tracking precision in wind disturbances. However, their properties have not been satisfactorily understood; consequently, their tuning is a trial-and-error process. A control engineer has two tools to tune an LQG controller: the choice of coordinate system of the controller model and the selection of weights of the LQG performance index. This article analyzes properties of an open- and closed-loop antenna. It shows that the proper choice of coordinates of the open-loop model simplifies the shaping of the closed-loop performance. The closed-loop properties are influenced by the LQG weights. The article shows the impact of the weights on the antenna closed-loop bandwidth, disturbance rejection properties, and antenna acceleration. The bandwidth and the disturbance rejection characterize the antenna performance, while the acceleration represents the performance limit set by the antenna hardware (motors). The article presents the controller tuning procedure, based on the coordinate selection and the weight properties. The procedure rationally shapes the closed-loop performance, as an alternative to the trial-and-error approach.

Gawronski, W.↗

Enabling Pinpoint Landing (PPL) on Mars

Pinpoint landing (PPL) missions will deliver about 1000 kg of useful payload to the surface of Mars. Mid-to-high latitude landing site compatibility is sought which should provide the means to land at sites up to 2.5 km above Mars mean surface altitude. A dispersion and control analysis process is presented which helps to identify the effects of PPL error drivers, quantify the effect of dispersions on landing error and quantify the landing position control capability/authority along the entry path. An entry/descent/landing (EDL) profile is provided. Guided aeroshell is the baseline for all candidate Mars atmospheric entry architectures. A two-stage architecture is considered for the aerodynamic decelerator descent phase: supersonic parachute plus guided subsonic parachute or high-Mach inflatable decelerator plus guided subsonic parachute. The powered descent phase uses propulsive descent stage for soft landing and final error reduction maneuvers. Studies have found that the aeroshell entry face dispersions can be large, but closed-loop guidance can null out resulting errors to within about 2 km. Additionally, projected parachute control is inadequate to correct worst case dispersions without wind forecast data. To mitigate the problems dispersions due to atmospheric uncertainty can be reduced by providing on-board external means to measure density and winds ahead of the vehicle, higher L/D control authority options for the subsonic parachute phase can be investigated, and decelerators with control authority options for the supersonic descent phase can be examined. A navigation error analysis and wind effects summary are included.

aerodynamic↗

The Lunar Atmosphere and Dust Environment Explorer (LADEE) Mission

The Lunar Atmosphere and Dust Environment Explorer (LADEE) is a Lunar science orbiter mission currently under development to address the goals of the National Research Council decadal surveys and the recent "Scientific Context for Exploration of the Moon" (SCEM) [1] report to study the pristine state of the lunar atmosphere and dust environment prior to significant human activities. LADEE will determine the composition of the lunar atmosphere and investigate the processes that control its distribution and variability, including sources, sinks, and surface interactions. LADEE will also determine whether dust is present in the lunar exosphere, and reveal the processes that contribute to its sources and variability. These investigations are relevant to our understanding of surface boundary exospheres and dust processes throughout the solar system, address questions regarding the origin and evolution of lunar volatiles, and have potential implications for future exploration activities. LADEE employs a high heritage science instrument payload including a neutral mass spectrometer, ultraviolet spectrometer, and dust sensor. In addition to the science payloads, LADEE will fly a laser communications system technology demonstration that could provide a building block for future space communications architectures. LADEE is an important component in NASA's portfolio of near-term lunar missions, addressing objectives that are currently not covered by other U.S. or international efforts, and whose observations must be conducted before large-scale human or robotic activities irrevocably perturb the tenuous and fragile lunar atmosphere. LADEE will also demonstrate the effectiveness of a low-cost, rapid-development program utilizing a modular bus design launched on the new Minotaur V launch vehicle. Once proven, this capability could enable future lunar missions in a highly cost constrained environment. This paper describes the LADEE objectives, mission design, and technical approach.

Spremo, Stevan↗

A Decision-Theoretic Approach to Autonomous Planetary Rover Control

The report discusses the: Decentralized Control of Markov Decision Processes. Study the complexity of decentralized control of Markov decision processes, and develop algorithms for finding optimal control policies. Scheduling Contract Algorithms. Develop an optimal method for scheduling runs of a contract anytime algorithm (one that takes the deadline as input) in situations where the deadline is unknown, multiple problem instances must be solved, and a multi-processor machine is available. Planetary Rover Control as a Markov Decision Process.Use the Markov decision process framework to formalize and solve problems in planetary rover control. Adaptive Peer Selection. Use reinforcement learning to maximize the expected down-load speed for a client in a peer-to-peer file sharing system.

Zilberstein, Shlomo↗

Information Theory Applied to Decision Making Structures

Decision making structures, such as control boards, process information on many topics as they select options for the system and project. The decisions are based on the information known to the board members and presenters (subject matter experts) and shared at the board during discussion. This information flow through this process can be modelled using information theory. Information theory provides a mathematical basis to understand the flow of information through the decision making process and the information needed for a particular decision. Information theory also provides the mathematical relationships on which to base the optimal decision making structure for a specific system development and organizational structure. Since decision making bodies provide control for the system or project, control theory can be used to construct a decision making model. This provides a starting point for adding cognitive science models. Information processing by each individual board participant can be represented through cognitive processes which are integrated across the board participants through information theory relationship. The set theory view of information theory provides a structure in which to look at the relationships between the participants in a decision making structure.

Watson, Michael D.↗

Information Theory Applied to Decision Making Structures

Decision making structures, such as control boards, process information on many topics as they select options for the system and project. The decisions are based on the information known to the board members and presenters (subject matter experts) and shared at the board during discussion. This information flow through this process can be modelled using information theory. Information theory provides a mathematical basis to understand the flow of information through the decision making process and the information needed for a particular decision. Information theory also provides the mathematical relationships on which to base the optimal decision making structure for a specific system development and organizational structure. Since decision making bodies provide control for the system or project, control theory can be used to construct a decision making model. This provides a starting point for adding cognitive science models. Information processing by each individual board participant can be represented through cognitive processes which are integrated across the board participants through information theory relationship. The set theory view of information theory provides a structure in which to look at the relationships between the participants in a decision making structure.

Watson, Michael D.↗

Processing Welding Images For Robot Control

Image data from two distinct windows used to locate weld features. Analyzer part of vision system described in companion article, "Image Control in Automatic Welding Vision System" (MFS-26035). Horizontal video lines define windows for viewing unwelded joint and weld pool. Data from picture elements outside windows not processed. Widely-separated local features carry no significance, but closely spaced features indicate welding feature. Image processor assigns confidence level to group of local features according to spacing and pattern.

Richardson, Richard W.↗

Cold Metal Transfer (CMT) Wire-Arc Additive Manufacturing (WAAM)

Aluminum has been identified as a compound within regolith and is likely to become a core component of our infrastructure on the lunar surface as in-situ resource utilization (ISRU) capabilities are advanced Large-scale components, outfitting, and repairs of aluminum materials can be fabricated with robotic wire arc additive manufacturing (WAAM) in order to inhabit the moon’s surface long term WAAM is a high value process for lunar advanced manufacturing as it does not require special containment to reduce explosion hazards such as powder-based additive processes and feedstock The welding process of cold metal transfer (CMT) is a relatively new variation of gas metal arc welding (GMAW, also known as MIG) that relies on the detection of a short circuit in the welding process to control the deposition droplet action, resulting in lower heat input and splatter compared to conventional MIG welding The past year was spent developing the CMT-WAAM process for aluminum materials, tested specialty feedstock, tested within the high vacuum environment, and advanced the MSFC capability to perform complex toolpathing from solid models Upcoming and future work includes large depositions working towards material certification for multiple feedstocks, in-situ monitoring, work to use recycled materials for the AM feedstock, and the design and fabrication of a parabolic flight experiment payload.

cold metal transfer↗

Cloud albedo control by cloud-top entrainment

Marine stratus and stratocumulus clouds exert a considerable influence on the earth's heat budget, mainly due to their high albedos relative to the ocean surface. It is therefore important to understand the processes that control the radiative properties of these extensive cloud systems, particularly during daylight hours. Aircraft measurements of a stratocumulus cloud deck taken around local noon during the 1987 field phase of the First International Satellite Cloud Climatology Project Regional Experiment are the topic of this paper. A mixing line analysis of data from a series of flight tracks across a strong gradient in cloud albedo provides evidence that variations in the water vapor content of the air above the marine inversion can be responsible for the albedo change. The implications of this unexpected result for climate modeling are discussed.

Hanson, Howard P.↗

Ecological study of peat landforms in Canada and Alaska

Over 20 percent of the land surface of Canada and Alaska is covered by peatlands, which may be defined as any waterlogged ecosystem with a minimum thickness of 20 cm of organic matter in the soil. Past investigations have demonstrated the value of aerial photographs in identifying the major vegetation types and analyzing the biotic and hydrogeologic processes that control the development of these peatlands. In the present study, LANDSAT TM imagery was used in conjunction with field studies to determine the utility of this satellite sensor for detecting these important processes. Although the vegetation landforms within these major peat basins are visible on aerial photographs, LANDSAT TM imagery provides essential new evidence for their analysis. Spectral data from the LANDSAT TM system provides: (1) synoptic views of the patterns across large portions of these peat basins, indicating important physiographic controls on peatland development, (2) more sensitive detection of the major vegetation types, allowing rapid quantitative estimates to be made of their distribution and aerial extent, (3) discrimination of bog areas with potentially rapid or slow rates of peat accumulation, (4) identification of discharge zones for groundwater, which apparently represents the most important source of alkalinity in these peat basins, and (5) detection of flow patterns in water tracks that appear nearly uniform on standard aerial photographs.

Glaser, Paul H.↗

Manufacturing Precise, Lightweight Paraboloidal Mirrors

A process for fabricating a precise, diffraction- limited, ultra-lightweight, composite- material (matrix/fiber) paraboloidal telescope mirror has been devised. Unlike the traditional process of fabrication of heavier glass-based mirrors, this process involves a minimum of manual steps and subjective judgment. Instead, this process involves objectively controllable, repeatable steps; hence, this process is better suited for mass production. Other processes that have been investigated for fabrication of precise composite-material lightweight mirrors have resulted in print-through of fiber patterns onto reflecting surfaces, and have not provided adequate structural support for maintenance of stable, diffraction-limited surface figures. In contrast, this process does not result in print-through of the fiber pattern onto the reflecting surface and does provide a lightweight, rigid structure capable of maintaining a diffraction-limited surface figure in the face of changing temperature, humidity, and air pressure. The process consists mainly of the following steps: 1. A precise glass mandrel is fabricated by conventional optical grinding and polishing. 2. The mandrel is coated with a release agent and covered with layers of a carbon- fiber composite material. 3. The outer surface of the outer layer of the carbon-fiber composite material is coated with a surfactant chosen to provide for the proper flow of an epoxy resin to be applied subsequently. 4. The mandrel as thus covered is mounted on a temperature-controlled spin table. 5. The table is heated to a suitable temperature and spun at a suitable speed as the epoxy resin is poured onto the coated carbon-fiber composite material. 6. The surface figure of the optic is monitored and adjusted by use of traditional Ronchi, Focault, and interferometric optical measurement techniques while the speed of rotation and the temperature are adjusted to obtain the desired figure. The proper selection of surfactant, speed or rotation, viscosity of the epoxy, and temperature make it possible to obtain the desired diffraction-limited, smooth (1/50th wave) parabolic outer surface, suitable for reflective coating. 7. A reflective coat is applied by use of conventional coating techniques. 8. Once the final figure is set, a lightweight structural foam is applied to the rear of the optic to ensure stability of the figure.

Hermann, Frederick Thomas↗