Search NASA⌕ Search

SEARCH · Search NASA

Results for “ReACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Strain control of composite superconductors to prevent degradation of superconducting magnets due to a quench: II. High-strength, laminated Ag-sheathed Bi-2223 tapes

In article I of this series, we described a spiral coil quench technique for probing the influence of the superconductor stress and strain state during normal operation on its margin to degradation during a quench and applied to a Bi-2212 round wire. Here we extend this technique to study the failure mechanisms and limits of high-strength Bi-2223 tapes experiencing a quench while carrying a large current in a high magnetic field. In contrast to Bi-2212 magnets made via a wind-and-react technique for which bending strains can be ignored, Bi-2223 magnets are made with a react-and-wind technique for which bending strain is significant. The critical tensile stress of Bi-2223 tapes (type HT-NX) decreases from >440 MPa for straight samples to 185 MPa after being bent to a diameter D of 50 mm. For HT-NX tapes with D = 50 mm, the quench degradation limit, measured using maximum allowable temperature during a quench T allowable , is greater than 300 K for axial tensile stress ${\sigma }_{a}$ < 94 MPa; it decreases with increasing tensile axial stress ${\sigma }_{a}$ nonlinearly, dropping to 230 K for ${\sigma }_{a}$ = 125 MPa. T allow able $({\sigma }_{a})$ experimental data at D = 50 mm is consistently predicted by a general strain model that assumes that quench degradation in NX/Bi-2223 is driven by axial tensile strain in Bi-2223 filaments exceeding the irreversible strain limit. The T allowable $({\sigma }_{a})$ is then predicted for various D including D = 80 mm important for NMR magnets. In conclusion, the given T allowable $(D,{\sigma }_{a})$ is easy to use and important for finding the balance between operation stress, and therefore magnetic field generation efficiency, and operation margin when designing a superconducting magnet using Bi-2223 tapes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nonparametric test of consistency between cosmological models and multiband CMB measurements

We present a novel approach to test the consistency of the cosmological models with multiband CMB data using a nonparametric approach. In our analysis we calibrate the REACT (Risk Estimation and Adaptation after Coordinate Transformation) confidence levels associated with distances in function space (confidence distances) based on the Monte Carlo simulations in order to test the consistency of an assumed cosmological model with observation. To show the applicability of our algorithm, we confront Planck 2013 temperature data with concordance model of cosmology considering two different Planck spectra combination. In order to have an accurate quantitative statistical measure to compare between the data and the theoretical expectations, we calibrate REACT confidence distances and perform a bias control using many realizations of the data. Our results in this work using Planck 2013 temperature data put the best fit ΛCDM model at 95% (∼ 2σ) confidence distance from the center of the nonparametric confidence set while repeating the analysis excluding the Planck 217 × 217 GHz spectrum data, the best fit ΛCDM model shifts to 70% (∼ 1σ) confidence distance. The most prominent features in the data deviating from the best fit ΛCDM model seems to be at low multipoles 18 < ℓ < 26 at greater than 2σ, ℓ ∼ 750 at ∼1 to 2σ and ℓ ∼ 1800 at greater than 2σ level. Excluding the 217×217 GHz spectrum the feature at ℓ ∼ 1800 becomes substantially less significance at ∼1 to 2σ confidence level. Results of our analysis based on the new approach we propose in this work are in agreement with other analysis done using alternative methods.

79 ASTRONOMY AND ASTROPHYSICS↗

Product-state control of bi-alkali-metal chemical reactions

We consider ultracold, chemically reactive scattering collisions of the diatomic molecules KRb. When two such molecules collide in an ultracold gas, we find that they are energetically forbidden from reacting to form the trimer species K{sub 2}Rb or Rb{sub 2}K, and hence can only react via the bond-swapping reaction 2KRb{yields}K{sub 2}+Rb{sub 2}. Moreover, the tiny energy released in this reaction can in principle be set to zero by applying electric or microwave fields, implying a means of controlling the available reaction channels in a chemical reaction.

74 ATOMIC AND MOLECULAR PHYSICS↗

Measurement of Charged-Pion Production in Deep-Inelastic Scattering off Nuclei with the CLAS Detector

Background: Energetic quarks in nuclear deep-inelastic scattering propagate through the nuclear medium. Processes that are believed to occur inside nuclei include quark energy loss through medium-stimulated gluon bremsstrahlung and intranuclear interactions of forming hadrons. More data are required to gain a more complete understanding of these effects. Purpose: To test the theoretical models of parton transport and hadron formation, we compared their predictions for the nuclear and kinematic dependence of pion production in nuclei. Methods: We have measured charged-pion production in semi-inclusive deep-inelastic scattering off D, C, Fe, and Pb using the CLAS detector and the CEBAF 5.014-GeV electron beam. We report results on the nuclear-to-deuterium multiplicity ratio for π + and π - as a function of energy transfer, four-momentum transfer, and pion energy fraction or transverse momentum—the first three-dimensional study of its kind. Results: The π + multiplicity ratio is found to depend strongly on the pion fractional energy z and reaches minimum values of 0.67 ± 0.03, 0.43 ± 0.02, and 0.27 ± 0.01 for the C, Fe, and Pb targets, respectively. The z dependencies of the multiplicity ratios for π + and π - are equal within uncertainties for C and Fe targets but show differences at the level of 10% for the Pb-target data. The results are qualitatively described by the GIBUU transport model, as well as with a model based on hadron absorption, but are in tension with calculations based on nuclear fragmentation functions. Conclusions: These precise results will strongly constrain the kinematic and flavor dependence of nuclear effects in hadron production, probing an unexplored kinematic region. They will help to reveal how the nucleus reacts to a fast quark, thereby shedding light on its color structure and transport properties and on the mechanisms of the hadronization process.

Moran, S.↗

Hindrance in the fusion of {sup 48}Ca+{sup 48}Ca.

The coupled-channels technique is applied to analyze recent fusion data for {sup 48}Ca+{sup 48}Ca. The calculations include the excitations of the low-lying 2{sup +}, 3{sup -}, and 5{sup -} states in projectile and target, and the influence of mutual excitations as well as the two-phonon quadrupole excitations is also investigated. The ion-ion potential is obtained by double-folding the nuclear densities of the reacting nuclei with the M3Y+repulsion effective interaction but a standard Woods-Saxon potential is also applied. The data exhibit a strong hindrance at low energy compared to calculations that are based on a standard Woods-Saxon potential but they can be reproduced quite well by applying the M3Y+repulsion potential with an adjusted radius of the nuclear density. The influence of the polarization of high-lying states on the extracted radius is discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Analysis of the multicomponent relativistic Boltzmann equation for electron scattering in big bang nucleosynthesis

Big-bang nucleosynthesis (BBN) is valuable as a means to constrain the physics of the early universe and it is the only probe of the radiation-dominated epoch. A fundamental assumption in BBN is that the nuclear velocity distributions obey Maxwell-Boltzmann (MB) statistics as they do in stars. Specifically, the BBN epoch is characterized by a dilute baryon plasma for which the velocity distribution of nuclei is mainly determined by the dominant Coulomb elastic scattering with mildly relativistic electrons. One must therefore deduce the momentum distribution for reacting nuclei from the multicomponent relativistic Boltzmann equation. However, the full multicomponent relativistic Boltzmann equation has only recently been analyzed and its solution has only been worked out in special cases. Moreover, a variety of schemes have been proposed that introduce nonthermal components into the BBN environment which can alter the thermal distribution of reacting nuclei. Here, we construct the relativistic Boltzmann equation in the context of BBN. We also derive a Langevin model and perform relativistic Monte-Carlo simulations which clarify the baryon distribution during BBN and can be used to analyze any relaxation from a nonthermal injection. Further, we show by these analyses that the thermalization process leads to a nuclear distribution function that remains very close to MB statistics even during the most relativistic environment relevant to BBN. Hence, the predictions of standard BBN remain unchanged.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Toward NS5 branes on the resolved cone over Y{sup p,q}

Motivated by recent developments in the understanding of the connection between five branes on resolved geometries and the corresponding generalizations of complex deformations in the context of the warped resolved deformed conifold, we consider the construction of five branes solutions on the resolved cone over Y{sup p,q} spaces. We establish the existence of supersymmetric five branes solutions wrapped on two-cycles of the resolved cone over Y{sup p,q} in the probe limit. We then use calibration techniques to begin the construction of fully back-reacted five branes; we present an Ansatz and the corresponding equations of motion. Our results establish a detailed framework to study back-reacted five branes wrapped on the resolved cone over Y{sup p,q} and as a first step we find explicit solutions and construct an asymptotic expansion with the expected properties.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Elemental transport coefficients in viscous plasma flows near local thermodynamic equilibrium

We propose a convenient formulation of elemental transport coefficients in chemically reacting and plasma flows locally approaching thermodynamic equilibrium. A set of transport coefficients for elemental diffusion velocities, heat flux, and electric current is introduced. These coefficients relate the transport fluxes with the electric field and with the spatial gradients of elemental fractions, pressure, and temperature. The proposed formalism based on chemical elements and fully symmetric with the classical transport theory based on chemical species, is particularly suitable to model mixing and demixing phenomena due to diffusion of chemical elements. The aim of this work is threefold: to define a simple and rigorous framework suitable for numerical implementation, to allow order of magnitude estimations and qualitative predictions of elemental transport phenomena, and to gain a deeper insight into the physics of chemically reacting flows near local equilibrium.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structural uncertainty assessment for fire-engulfed objects in crosswind: Establishing credibility for a multiphysics wall-modeled large-eddy simulation paradigm

A structural uncertainty validation study for a large-scale, fire-engulfed, elevated object subjected to crosswind is presented to establish the credibility of a high-fidelity, low-Mach, turbulent reacting flow wall-modeled large-eddy simulation (WMLES) approach that includes multiphysics coupling to participating media radiation and conjugate heat transfer. To establish that WMLES can accurately predict surface quantities including drag and pressure coefficient in the low-Mach crosswind regime, a foundational elevated isothermal cylinder validation case is presented at a similar gap-to-diameter ratio of 0.25, spanning the subcritical to supercritical drag regime (Re 𝐷 = 1.1 × 10 5 and 4.3 × 10 5 , respectively). Here, this study exercised both static and dynamic coefficient LES (Smagorinsky and 𝑘 sgs ) with both local and exchange-based velocity sampling. Results showcase that the drag crisis (or the sudden drop in drag coefficient at increased Re 𝐷 ) is well captured when using an exchange-based dynamic coefficient WMLES methodology, while noting lack of mesh convergence and overall drag and pressure coefficient predictively when using a static coefficient, local velocity sampling WMLES. For the 𝒪⁡(10) m JP-8 liquid pool fire crosswind validation study presented, two experimental crosswind configurations (2 m/s and 9.5 m/s) are showcased for a fire-engulfed mock fuselage roughly 4 m in diameter. Using the best model-form practices identified in the isothermal study, dynamic coefficient 𝑘 sgs exchange-based WMLES fire validation findings demonstrate accurate peak irradiation and skin temperature predictions as a function of crosswind magnitude. Excessive yaw in the low-crosswind fuselage configuration, consistent with experimental findings, captured a significant predicted asymmetry in flame attachment and heat flux toward the downwind cylindrical cap—indicative of axial vortex structures transporting the flame along the upper and lower fuselage leeward surface. All fire mesh resolution simulations captured the experimental finding that as crosswind increased, predicted flame shape and peak irradiation magnitude onto the fuselage transitioned from a windward to a leeward cylinder location due to the migration of the upper- to lower-shear fuel/air mixing layer thereby demonstrating the novelty, significance, and credibility of this high-fidelity WMLES reacting flow framework.

Domino, Stefan Paul [Sandia National Laboratories ↗

Lyapunov exponent as a metric for assessing the dynamic content and predictability of large-eddy simulations

Metrics used to assess the quality of large-eddy simulations commonly rely on a statistical assessment of the solution. While these metrics are valuable, a dynamic measure is desirable to further characterize the ability of a numerical simulation for capturing dynamic processes inherent in turbulent flows. To address this issue, a dynamic metric based on the Lyapunov exponent is proposed which assesses the growth rate of the solution separation. Specifically, this metric is applied to two turbulent flow configurations: forced homogeneous isotropic turbulence and a turbulent jet diffusion flame. First, it is shown that, despite the direct numerical simulation (DNS) and large-eddy simulation (LES) being high-dimensional dynamical systems with O(107) degrees of freedom, the separation growth rate qualitatively behaves like a lower-dimensional dynamical system, in which the dimension of the Lyapunov system is substantially smaller than the discretized dynamical system. Second, a grid refinement analysis of each configuration demonstrates that as the LES filter width approaches the smallest scales of the system the Lyapunov exponent asymptotically approaches a plateau. Third, a small perturbation is superimposed onto the initial conditions of each configuration, and the Lyapunov exponent is used to estimate the time required for divergence, thereby providing a direct assessment of the predictability time of simulations. By comparing inert and reacting flows, it is shown that combustion increases the predictability of the turbulent simulation as a result of the dilatation and increased viscosity by heat release. The predictability time is found to scale with the integral time scale in both the reacting and inert jet flows. Fourth, an analysis of the local Lyapunov exponent is performed to demonstrate that this metric can also determine flow-dependent properties, such as regions that are sensitive to small perturbations or conditions of large turbulence within the flow field. Finally, it is demonstrated that the global Lyapunov exponent can be utilized as a metric to determine if the computational domain is large enough to adequately encompass the dynamic nature of the flow.

42 ENGINEERING↗

Domain Wall Reactions in Multiple-Order Parameter Ferroelectrics

The motion of domain walls is crucial for ferroelectric switching. Conventionally, the switching dynamics is believed to be determined by the motion of one or a few low-energy domain wall types of dominant population. Here, we challenge this conventional idea in multiple-order-parameter ferroelectrics. Using hafnia as example, we show that the multiple-order-parameter nature not only provides various mobile domain walls and defectlike immobile domain walls, but also enables the domain wall reactions. In analogy with chemical reactions where substances react to form new substances, domain walls could also react to form other domain walls during switching. We identify several elementary domain wall reaction types including synthesis, decomposition, and exchange reactions. Domain walls are continually changed by these reactions during switching so that the switching behavior reflects the statistical average of many domain wall types with distinct mobility and stability. These reactions also lead to phenomenon like remanent nuclei and defect-site nucleation that facilitate switching and lower coercive field. Finally, the concept of domain wall reaction is not limited to hafnia but can be generalized to any multiple-order-parameter ferroelectric. As a result, this Letter conceptualizes domain wall reaction, expands the theory of ferroelectric switching, and suggests a practical way for defect engineering to control switching behavior.

36 MATERIALS SCIENCE↗

Characterizing Impacts of Storage Faults on HPC Applications: A methodology and insights

In recent years, the increasing complexity in scientific simulations and emerging demands for training heavy artificial intelligence models require massive and fast data accesses, which urges high-performance computing (HPC) platforms to equip with more advanced storage infrastructures such as solid-state disks (SSDs). While SSDs offer high-performance I/O, it remains unclear about the reliability challenges faced by the HPC applications under the SSD-related failures, in particular, failures resulting in data corruptions. The goal of this paper is to understand the impact of SSD-related data corruptions on the behaviors of complex HPC applications. To this end, we propose FFIS, a FUSE-based fault injection framework that systematically introduces storage faults into the application layer to model the errors originated from SSDs. FFIS is able to plant different I/O related faults into the data returned from underlying file systems, which also enables the investigation on the error resilience characteristics of the scientific file format for the first time. We demonstrate the use of FFIS with three representative real HPC applications, show how each application reacts to the data corruptions, and provide insights on the error resilience of the widely-adopted HDF5 file format for the HPC applications.

Fang, Bo↗

Fabrication of 8-Strand Rutherford Cables Using Roped Strands Made from Ultrafine Wires

Conventional Rutherford cables are typically made from solid round wire. While multi-stage cables have been made elsewhere, the purpose was usually to achieve a higher strand count and therefore a higher current carrying capability. In this work, we attempt to use two-stage roped strands made from ultrafine wires to fabricate Rutherford cables. The ultimate goal of this work is to obtain a very flexible cable that can wind accelerator magnet coils with a very tight bend radius in both the “easy way” (along the broad face of the cable) and the “hard way” (along the edge of the cable) in the wind-and-react manner, or wind coils with a radius typically used today but in the react and-wind manner with a much reduced degradation in critical current. We report our experience fabricating such Rutherford cables at the Lawrence Berkeley National Laboratory, and the initial findings from the analysis of the experimental cables made. We will discuss how the conventional wisdom and some rules of thumb for making Rutherford cables are no longer applicable or relevant, and the new thinking required in designing these cables.

Pong, Ian↗

3-D Unsteady Model for Be-Steam Reaction in Water-Cooled Ceramic Breeder Blanket

Here, the design of the water-cooled ceramic breeder (WCCB) blanket includes beryllium multiplier layers. At elevated temperature, beryllium reacts with steam in an exothermic reaction producing beryllium oxide and hydrogen. Such situation may occur in WCCB in the case of the rupture of one of the cooling pipes in the blanket module. This process occurs locally in a complex 3-D geometry of the blanket containing several different granular levels and a network of cooling pipes and structural supports. The process is also inherently unsteady since reaction rate depends on concentration of steam and pure beryllium which changes in time. In order to perform the detailed analysis of the process, the model of the reacting flowthrough porous media was developed and introduced into 3-D computational fluid dynamics code. In this model, granular beds are introduced as porous solids simplifying the model geometry and reducing typical mesh size to manageable amount of tens of millions of elements. A reaction rate between solid beryllium and steam is obtained from experimental results, and depends on temperature and concentration of the reactants. The differential equation for beryllium oxide fraction is introduced, allowing obtaining distributions of beryllium oxide in space and time. Multicomponent flow consisting of a homogenous mixture of steam and hydrogen is considered flowing through the porous solid with variable properties. Sink and source terms for steam and hydrogen fractions are determined by local beryllium oxide mass fraction source according to the molar ratios of beryllium steam reaction. The conjugated heat transfer approach is applied to calculate heat transfer in support structures as well as coolant flow, simultaneously with the porous medium steam flow in a blanket's granular beds. The model is validated using experimental data on beryllium steam reaction for granular bed samples.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Design and synthesis of diazirine‐containing dyes for polypropylene fibre: A study on the effect of alkyl chain

Abstract The dyeing of polypropylene fabrics utilising conventional‐disperse dyes often meets poor colour yield and fastness problems, fundamentally caused by the low affinity between dyes and polypropylene fibres. In this article, a new class of hydrophobic reactive dyes that can react with polypropylene were designed using diazirine moiety as a reactive group, azo structure as a chromophore, and an ester group as a linking bridge. The difference among these dyes was the alkyl chain length on the azo chromophore, which was used to fine‐tune the affinity between the dyes and fibre. The structures of the synthesised dyes and intermediates were characterised and confirmed using nuclear magnetic resonance, mass spectrometry, and infrared spectrometry. The absorption and thermal properties of the dyes were also studied to ensure their feasibility for dyeing application. In addition, the diazirine dyes were successfully applied to dye polypropylene fabrics using a two‐step process by dyeing in a non‐aqueous solvent and fixing it under heating. The dyes and polypropylene fibre were demonstrated to react, where the fixation values were in the range 64.5–76.4%. The systematic study of the structure–property relationship demonstrated the positive effect of the alkyl chain in promoting colour yield, however, accompanied by a slightly reduced fixation value. Due to the chemical bonding of the dye molecules to the fibre, the dyed polypropylene fabrics exhibited excellent colour fastness property, making the dyeing technology very promising for future industrial applications.

Guo, Guangluo↗

Current Understanding and Remaining Challenges in Modeling Long-Term Degradation of Borosilicate Nuclear Waste Glasses

Chemical durability is not a single material property that can be uniquely measured. Instead it is the response to a host of coupled material and environmental processes whose rates are estimated by a combination of theory, experiment, and modeling. High-level nuclear waste (HLW) glass is perhaps the most studied of any material yet there remain significant technical gaps regarding their chemical durability. The phenomena affecting the long-term performance of HLW glasses in their disposal environment include surface reactions, transport properties to and from the reacting glass surface, and ion exchange between the solid glass and the surrounding solution and alteration products. The rates of these processes are strongly influenced and are coupled through the solution chemistry, which is in turn influenced by the reacting glass and also by reaction with the near-field materials and precipitation of alteration products. Therefore, those processes must be understood sufficiently well to estimate or bound the performance of HLW glass in its disposal environment over geologic time-scales. This article summarizes the current state of understanding of surface reactions, transport properties, and ion exchange along with the near-field materials and alteration products influences on solution chemistry and glass reaction rates. Also summarized are the remaining technical gaps along with recommended approaches to fill those technical gaps.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Foaming during Nuclear Waste Melter Feeds Conversion to Glass: Application of Evolved Gas Analysis

During the final stages of batch-to-glass conversion in a waste-glass melter, gases evolving in the cold cap produce primary foam, the formation and collapse of which control the glass production rate via its effect on heat transfer to the reacting batch. We performed quantitative evolved gas analysis (EGA) for several HLW melter feeds with temperatures ranging from 100 °C to 1150 °C, the whole temperature span in a cold cap. EGA results were supplemented with visual observation of batch-to-glass transition using the feed expansion tests. Upon heating, most of the gases—mainly H2O, CO2, NO, NO2, N2 and O2—evolve at temperatures below 700 °C and escape directly to the atmosphere through open porosity. However, as open porosity closes when enough glass-forming melt appears at 720 °C, the residual gas evolution leads to the formation of primary foam. We found that primary foaming is mostly caused by the decomposition of residual carbonates, though oxygen evolution from iron-redox reaction can also play a role. We also show that the gas evolution shifts to a higher temperature when the heating rate increases. The implications for the mathematical modeling of foam layer in the cold cap are presented.

Hujova, Miroslava↗

Chemical and mechanical consequences of environmental barrier coating exposure to calcium-magnesium-aluminosilicate.

The success of Si-based ceramics as high-temperature structural materials for gas turbine applications relies on the use of environmental barrier coatings (EBCs) with low silica activity, such as Ba{sub 1-x}Sr{sub x}Al{sub 2}Si{sub 2}O{sub 8} (BSAS), which protect the underlying components from oxidation and corrosion in combustion environments containing water vapor. One of the current challenges concerning EBC lifetime is the effect of sandy deposits of calcium-magnesium-aluminosilicate (CMAS) glass that melt during engine operation and react with the EBC, changing both its composition and stress state. In this work, we study the effect of CMAS exposure at 1300 C on the residual stress state and composition in BSAS-mullite-Si-SiC multilayers. Residual stresses were measured in BSAS multilayers exposed to CMAS for different times using high-energy X-ray diffraction. Their microstructure was studied using a combination of scanning electron microscopy and transmission electron microscopy techniques. Our results show that CMAS dissolves the BSAS topcoat preferentially through the grain boundaries, dislodging the grains and changing the residual stress state in the topcoat to a nonuniform and increasingly compressive stress state with increasing exposure time. The presence of CMAS accelerates the hexacelsian-to-celsian phase transformation kinetics in BSAS, which reacts with the glass by a solution-reprecipitation mechanism. Precipitates have crystallographic structures consistent with Ca-doped celsian and Ba-doped anorthite.

36 MATERIALS SCIENCE↗