Search NASA⌕ Search

SEARCH · Search NASA

Results for “Representativeness Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Predictions of Control Inputs, Periodic Responses and Damping Levels of an Isolated Experimental Rotor in Trimmed Flight

Since the early 1990s the Aeroflightdynamics Directorate at the Ames Research Center has been conducting tests on isolated hingeless rotors in hover and forward flight. The primary objective is to generate a database on aeroelastic stability in trimmed flight for torsionally soft rotors at realistic tip speeds. The rotor test model has four soft inplane blades of NACA 0012 airfoil section with low torsional stiffness. The collective pitch and shaft tilt are set prior to each test run, and then the rotor is trimmed in the following sense: the longitudinal and lateral cyclic pitch controls are adjusted through a swashplate to minimize the 1/rev flapping moment at the 12 percent radial station. In hover, the database comprises lag regressive-mode damping with pitch variations. In forward flight the database comprises cyclic pitch controls, root flap moment and lag regressive-mode damping with advance ratio, shaft angle and pitch variations. This report presents the predictions and their correlation with the database. A modal analysis is used, in which nonrotating modes in flap bending, lag bending and torsion are computed from the measured blade mass and stiffness distributions. The airfoil aerodynamics is represented by the ONERA dynamic stall models of lift, drag and pitching moment, and the wake dynamics is represented by a state-space wake model. The trim analysis of finding, the cyclic controls and the corresponding, periodic responses is based on periodic shooting with damped Newton iteration; the Floquet transition matrix (FTM) comes out as a byproduct. The stabillty analysis of finding the frequencies and damping levels is based on the eigenvalue-eigenvector analysis of the FTM. All the structural and aerodynamic states are included from modeling to trim analysis. A major finding is that dynamic wake dramatically improves the correlation for the lateral cyclic pitch control. Overall, the correlation is fairly good.

Gaonkar, G. H.↗

Nuclear Forensics: A Holistic Overview

Discussions of nuclear forensics are often restricted to work performed by radio-chemists measuring nuclear material attributes in the laboratory. However, this represents only one portion of the work required to answer critical questions. Laboratory analysis results in measurements that need to be evaluated. The results of those evaluations must be put into their proper context in order for them to be useful to others and often require merging those results with additional information. This may contribute to attribution, by virtue of inclusion or exclusion. Finally, the end product must be presented such that appropriate actions can be taken. This could include prosecution by law enforcement, policy initiatives on the part of legislative bodies, or military action in the case of nuclear attack (whether that attack is preempted or not). Using the discovery of a sample of plutonium during cleanup activities at Hanford in 2004, we will step through the process of discovery (representing an interdiction), initial field analysis, laboratory analysis, data evaluation and merging with additional data (similar to law enforcement and/or all source), thereby providing an example of an integrated approach.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Functional Group Analysis for Diesel-like Mixing-Controlled Compression Ignition Combustion Blendstocks

This report addresses the suitability of hydrocarbon and oxygenate functional groups for use as a diesel-like fuel blending component in an advanced, mixing-controlled, compression ignition combustion engine. The functional groups are chosen from those that could be derived from a biomass feedstock, and represent a full range of chemistries. This first systematic analysis of functional groups will be of value to all who are pursuing new bio-blendstocks for diesel-like fuels.

09 BIOMASS FUELS↗

Complex-wide representation of material packaged in 3013 containers

The DOE sites packaging plutonium oxide materials packaged according to Department of Energy 3013 Standard (DOE-STD-3013) are responsible for ensuring that the materials are represented by one or more samples in the Materials Identification and Surveillance (MIS) program. The sites categorized most of the materials into process groups, and the remaining materials were characterized, based on the prompt gamma analysis results. The sites issued documents to identify the relationships between the materials packaged in 3013 containers and representative materials in the MIS program. These “Represented” documents were then reviewed and concurred with by the MIS Working Group. However, these documents were developed uniquely at each site and were issued before completion of sample characterization, small-scale experiments, and prompt gamma analysis, which provided more detailed information about the chemical impurities and the behavior of the material in storage. Therefore, based on the most recent data, relationships between the materials packaged in 3013 containers and representative materials in the MIS program been revised. With the prompt gamma analysis completed for Hanford, Rocky Flats, and Savannah River Site 3013 containers, MIS items have been assigned to the 3013 containers for which representation is based on the prompt gamma analysis results. With the revised relationships and the prompt gamma analysis results, a Master “Represented” table has been compiled to document the linkages between each 3013 container packaged to date and its representative MIS items. This table provides an important link between the Integrated Surveillance Program database, which contains information about each 3013 container to the MIS items database, which contains the characterization, prompt gamma data, and storage behavior data from shelf-life experiments for the representative MIS items.

42 ENGINEERING↗

Complex-wide representation of material packaged in 3013 containers

The DOE sites packaging plutonium oxide materials packaged according to Department of Energy 3013 Standard (DOE-STD-3013) are responsible for ensuring that the materials are represented by one or more samples in the Materials Identification and Surveillance (MIS) program. The sites categorized most of the materials into process groups, and the remaining materials were characterized, based on the prompt gamma analysis results. The sites issued documents to identify the relationships between the materials packaged in 3013 containers and representative materials in the MIS program. These “Represented” documents were then reviewed and concurred with by the MIS Working Group. However, these documents were developed uniquely at each site and were issued before completion of sample characterization, small-scale experiments, and prompt gamma analysis, which provided more detailed information about the chemical impurities and the behavior of the material in storage. Therefore, based on the most recent data, relationships between the materials packaged in 3013 containers and representative materials in the MIS program been revised. With the prompt gamma analysis completed for Hanford, Rocky Flats, and Savannah River Site 3013 containers, MIS items have been assigned to the 3013 containers for which representation is based on the prompt gamma analysis results. With the revised relationships and the prompt gamma analysis results, a Master “Represented” table has been compiled to document the linkages between each 3013 container packaged to date and its representative MIS items. This table provides an important link between the Integrated Surveillance Program database, which contains information about each 3013 container to the MIS items database, which contains the characterization, prompt gamma data, and storage behavior data from shelf-life experiments for the representative MIS items.

Narlesky, Joshua E.↗

Regional techno-economic and life-cycle analysis of the pyrolysis-bioenergy-biochar platform for carbon-negative energy

This study investigates the sensitivity of greenhouse gas (GHG) emissions and the minimum fuel selling price for a 2000 metric ton day –1 integrated pyrolysis–bioenergy–biochar platform with respect to the biorefinery location and biomass types. The regional techno–economic and life–cycle analysis is evaluated in three US counties using representative crops: rice in Glenn County (California), corn in Hamilton County (Iowa), and peanuts in Jackson County (Florida). We evaluate the biochar selling price considering crop yield increases of 0.6%, 2.9%, and 10% after biochar application over 20 years in Glenn County, Hamilton County, and Jackson County, respectively. The biochar prices are calculated under low and high commodity prices to determine upper and lower bounds. Jackson County has the most economically beneficial scenario with an average minimum fuel selling price (MFSP) of 1.55 gal –1 of biofuel produced whereas Hamilton County has the highest average MFSP of 3.82 gal –1 . The life–cycle analysis shows that woody biomass has a strong potential to produce carbon–negative energy compared to grass and straw. As a result, of the 304 cases scenarios considered for this platform, 64% could produce biofuel with negative GHG emissions, which would meet the Renewable Fuel Standard (RFS) target for cellulosic biofuels.

09 BIOMASS FUELS↗

Refinement of Modeling Techniques for the Structural Evaluation of Hanford Single-Shell Nuclear Waste Storage Tanks - 12288

The single-shell tanks at the Hanford Site (in Washington State, USA) were constructed between 1943 and 1964 and are well beyond their estimated 25 year design life. This article discusses the structural analysis approach and modeling challenges encountered during the ongoing analysis of record for evaluating the structural integrity of the single-shell tanks. There are several geometrical and material nonlinearities and uncertainties to be dealt with while performing the modern finite element analysis of these tanks. The analysis takes into account the temperature history of the tanks and allowable mechanical operating loads for proper estimation of creep strains and thermal degradation of material properties. The loads prescribed in the analysis of record models also include anticipated loads that may occur during waste retrieval and closure. Due to uncertainty in a number of modeling details, sensitivity studies were conducted to address questions related to boundary conditions that realistically or conservatively represent the influence of surrounding tanks in a tank farm, the influence of backfill excavation slope, the extent of backfill and the total extent of undisturbed soil surrounding the backfill. Because of the limited availability of data on the thermal and operating history for many of the individual tanks, some of the data was assumed or interpolated. However, the models developed for the analysis of record represent the bounding scenarios and include the loading conditions that the tanks were subjected to or anticipated. The modeling refinement techniques followed in the analysis of record resulted in conservative estimates for force and moment demands at various sections in the concrete tanks. This article discusses the modeling aspects related to Type-II and Type-III single-shell tanks. The modeling techniques, methodology and evaluation criteria developed for evaluating the structural integrity of single-shell tanks at Hanford are in general applicable to other similar tanks or underground concrete storage structures. This article presented the details of the finite element models and analysis approach followed during the ongoing effort to establish structural integrity of single shell tanks at the Hanford site. The details of the material constitutive models applicable to the underground Hanford concrete tanks that capture the thermal and creep induce degradation are also presented. The thermal profiles were developed based on the available tank temperature data for the Type II and Type III single-shell tanks, and they were chosen to yield conservative demands under the thermal and operating loads analysis of these tanks. Sensitivity studies were conducted to address two issues regarding the soils modeled around the single-shell tanks. The results indicate that excluding the boundary separating the backfill soil from the undisturbed soil will result in conservative demands (plots 14b and 14c green lines for circumferential Demand/Capacity ratios). The radial extent study indicated that the soil model extending to 240 ft gave more conservative results than the model with 62 ft of soil (plots 17a and 17c magenta lines for hoop Demand/Capacity ratios). Based on these results, a 240 ft far-field soil boundary with backfill throughout the lateral extent was recommended and used for the finite element models used in the Type-II and Type-III analyses of record. The modeling effort and sensitivity studies discussed in this article helped in developing bounding models for the structural integrity evaluation of single shell tanks at the Hanford site. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Volatiles in interplanetary dust particles - A review

The paper presents a review of the volatiles found within interplanetary dust particles. These particles have been shown to represent primitive material from early in the solar system's formation and also may contain records of stellar processes. The organogenic elements (i.e., H, C, N, O, and S) are among the most abundant elements in our solar system, and their abundances, distributions, and isotopic compositions in early solar system materials permit workers to better understand the processes operating early in the evolutionary history of solar system materials. Interplanetary dust particles have a range of elemental compositions, but generally they have been shown to be similar to carbonaceous chondrites, the solar photosphere, Comet Halley's chondritic cores, and matrix materials of chondritic chondrites. Recovery and analysis of interplanetary dust particles have opened new opportunities for analysis of primitive materials, although interplanetary dust particles represent major challenges to the analyst because of their small size.

Gibson, Everett K., Jr.↗

Radiant Energy Measurements from a Scaled Jet Engine Axisymmetric Exhaust Nozzle for a Baseline Code Validation Case

A non-flowing, electrically heated test rig was developed to verify computer codes that calculate radiant energy propagation from nozzle geometries that represent aircraft propulsion nozzle systems. Since there are a variety of analysis tools used to evaluate thermal radiation propagation from partially enclosed nozzle surfaces, an experimental benchmark test case was developed for code comparison. This paper briefly describes the nozzle test rig and the developed analytical nozzle geometry used to compare the experimental and predicted thermal radiation results. A major objective of this effort was to make available the experimental results and the analytical model in a format to facilitate conversion to existing computer code formats. For code validation purposes this nozzle geometry represents one validation case for one set of analysis conditions. Since each computer code has advantages and disadvantages based on scope, requirements, and desired accuracy, the usefulness of this single nozzle baseline validation case can be limited for some code comparisons.

Baumeister, Joseph F.↗

Robust detection, isolation and accommodation for sensor failures

The objective is to extend the recent advances in robust control system design of multivariable systems to sensor failure detection, isolation, and accommodation (DIA), and estimator design. This effort provides analysis tools to quantify the trade-off between performance robustness and DIA sensitivity, which are to be used to achieve higher levels of performance robustness for given levels of DIA sensitivity. An innovations-based DIA scheme is used. Estimators, which depend upon a model of the process and process inputs and outputs, are used to generate these innovations. Thresholds used to determine failure detection are computed based on bounds on modeling errors, noise properties, and the class of failures. The applicability of the newly developed tools are demonstrated on a multivariable aircraft turbojet engine example. A new concept call the threshold selector was developed. It represents a significant and innovative tool for the analysis and synthesis of DiA algorithms. The estimators were made robust by introduction of an internal model and by frequency shaping. The internal mode provides asymptotically unbiased filter estimates.The incorporation of frequency shaping of the Linear Quadratic Gaussian cost functional modifies the estimator design to make it suitable for sensor failure DIA. The results are compared with previous studies which used thresholds that were selcted empirically. Comparison of these two techniques on a nonlinear dynamic engine simulation shows improved performance of the new method compared to previous techniques

Emami-Naeini, A.↗

A comprehensive analysis of the performance characteristics of the Mount Laguna solar photovoltaic installation

This paper represents the first comprehensive survey of the Mount Laguna Photovoltaic Installation. The novel techniques used for performing the field tests have been effective in locating and characterizing defective modules. A comparative analysis on the two types of modules used in the array indicates that they have significantly different failure rates, different distributions in degradational space and very different failure modes. A life cycle model is presented to explain a multimodal distribution observed for one module type. A statistical model is constructed and it is shown to be in good agreement with the field data.

Shumka, A.↗

Influences of cloud vertical overlapping on the calculated cloud albedo and their validation with satellite observations

Cloud albedo is expected to influence cloud radiative forcing in addition to cloud fraction, and inadequate description of the cloud overlapping effects on the cloud fraction may influence the simulated cloud fraction, and thus the relative cloud radiative forcing (RCRF) and cloud albedo. In this study, we first present a new formula by extending that presented previously in Liu et al. (2011) to consider multilayer clouds directly in the relationship between cloud albedo, cloud fraction and RCRF, and then quantitatively evaluate the effects of different cloud vertical overlapping structures, represented by the decorrelation length scales (L cf ), on the simulated cloud albedos. We use the BCC_AGCM2.0_CUACE/Aero model with simultaneous validation by observations from the Clouds and the Earth's Radiation Energy System (CERES) satellite. When L cf < 4 km (i.e., the cloud overlap is closer to the random overlap), the simulated cloud albedos are generally in good agreement with the satellite-based albedos for December– February and June–August; when L cf ≥ 4 km (i.e., the cloud vertical overlap is closer to the maximum overlap), the difference between simulated and observed cloud albedos became larger, due mainly to significant differences in cloud fractions and RCRF. Further quantitative analysis shows that the relative Euclidean distance, which represents the degree of overall model–observation disagreement, increases with the L cf for all three variables (cloud albedo, cloud fraction and RCRF), indicating the importance of cloud vertical overlapping in determining the accuracy of the calculated cloud albedo for multilayer clouds.

54 ENVIRONMENTAL SCIENCES↗

Complex history of admixture during citrus domestication revealed by genome analysis

Although Citrus is the most globally significant tree fruit, its domestication history is poorly understood. Cultivated citrus types are believed to comprise selections from and/or hybrids of several wild progenitor species, but the identities of these progenitors, and their contribution to modern cultivars, remain controversial. Here we report the genomes of a collection of mandarins, pummelos, and oranges, including a high quality reference sequence from a haploid Clementine mandarin. By comparative genome analysis we show that these cultivated types can be derived from two progenitor species. Cultivated pummelos represent selections from a single progenitor species C. maxima. Unexpectedly, however, we find that cultivated mandarins are introgressions of C. maxima into a distinct second population that we identify with the ancestral wild mandarin species C. reticulata. Sweet and sour oranges are found to be interspecific hybrids. Sweet orange, the most widely cultivated citrus, arose as the offspring of previously admixed individuals. In contrast, sour (or Seville) orange is an F1 hybrid of pure C. maxima and C. reticulata parents, implying that wild mandarins were part of the early breeding germplasm. Surprisingly, we also find that a wild Chinese mandarin from Mangshan, China shows substantial sequence divergence from C. reticulata and appears to represent a distinct taxon. Understanding the relationships and phylogeny of cultivated citrus through genome analysis will clarify taxonomic relationships and enable previously inconceivable opportunities for sequence-directed genetic improvement. Citrus are widely consumed worldwide as juice or fresh fruit, providing important sources of vitamin C and other health-promoting compounds. Global production in 2012 exceeded 86 million metric tons, with an estimated value of US$9 billion (http://www.fas.usda.gov/psdonline/circulars/citrus.pdf). The very narrow genetic diversity of cultivated citrus makes it highly vulnerable to disease outbreaks, including citrus greening disease (also known as Huanglongbing) that is rapidly spreading throughout the world's major citrus producing regions1. Understanding the population genomics and domestication of citrus will enable strategies for improvements to citrus including resistance to greening and other diseases. The domestication and distribution of edible citrus types began several thousand years ago in Southeast Asia and spread globally following ancient land and sea routes. The lineages that gave rise to most modern cultivated varieties, however, are lost in undocumented antiquity, and their identities remain controversial2, 3. Several features of Citrus biology and cultivation make deciphering these origins difficult. Cultivated varieties are typically propagated clonally by grafting and through asexual seed production (apomixis via nucellar polyembryony) to maintain desirable combinations of traits (Fig. 1). Thus many important cultivar groups have characteristic basic genotypes that presumably arose through interspecific hybridization and/or successive introgressive hybridizations of wild ancestral species. These domestication events predated the global expansion of citrus cultivation by hundreds or perhaps thousands of years, with no record of the domestication process. Diversity within such groups arises through accumulated somatic mutations, generally without sexual recombination, either as limb sports on trees or variants among apomictic seedling progeny. Two wild species are believed to have contributed to domesticated pummelos, mandarins and oranges. Based on morphology and genetic markers, pummelos have generally been identified with the wild species C. maxima (Burm.) Merrill that is indigenous to Southeast Asia. Although mandarins are similarly widely identified with the species C. reticulata Blanco 4-6, wild populations of C. reticulata have not been definitively described. Various authors have taken dif

99 GENERAL AND MISCELLANEOUS↗

Filtering and error analysis via the UDU super T covariance factorization

Kalman filter algorithms based on the UDU super T covariance factorization are discussed, with special attention given to algorithm implementation efficiency. A U-D-factored covariance error-analysis algorithm is formulated, and its efficiency and numerical stability are demonstrated in a representative orbit determination problem. The numerical results are compared with those obtained using covariance error-analysis formulas, and the comparison highlights the numerical superiority of the present algorithm. A byproduct of the U-D analysis is a highly efficient algorithm mechanization of the arbitrary gain covariance update formula.

Thornton, C. L.↗

Critical joints in large composite primary aircraft structures. Volume 1: Technical summary

A program was conducted at Douglas Aircraft Company to develop the technology for critical joints in composite wing structure that meets all the design requirements of a 1990 commercial transport aircraft. In fulfilling this objective, analytical procedures for joint design and analysis were developed during Phase 1 of the program. Tests were conducted at the element level to supply the empirical data required for methods development. Large composite multirow joints were tested to verify the selected design concepts and for correlation with analysis predictions. The Phase 2 program included additional tests to provide joint design and analysis data, and culminated with several technology demonstration tests of a major joint area representative of a commercial transport wing. The technology demonstration program of Phase 2 is discussed. The analysis methodology development, structural test program, and correlation between test results and analytical strength predictions are reviewed.

Bunin, Bruce L.↗

Physical and Radiative Characteristic and Long-term Variability of the Okhotsk Sea Ice Cover

Much of what we know about the large scale characteristics of the Okhotsk Sea ice cover has been provided by ice concentration maps derived from passive microwave data. To understand what satellite data represent in a highly divergent and rapidly changing environment like the Okhotsk Sea, we take advantage of concurrent satellite, aircraft, and ship data acquired on 7 February and characterized the sea ice cover at different scales from meters to hundreds of kilometers. Through comparative analysis of surface features using co-registered data from visible, infrared and microwave channels we evaluated the general radiative and physical characteristics of the ice cover as well as quantify the distribution of different ice types in the region. Ice concentration maps from AMSR-E using the standard sets of channels, and also only the 89 GHz channel for optimal resolution, are compared with aircraft and high resolution visible data and while the standard set provides consistent results, the 89 GHz provides the means to observe mesoscale patterns and some unique features of the ice cover. Analysis of MODIS data reveals that thick ice types represents about 37% of the ice cover indicating that young and new ice types represent a large fraction of the ice cover that averages about 90% ice concentration according to passive microwave data. These results are used to interpret historical data that indicate that the Okhotsk Sea ice extent and area are declining at a rapid rate of about -9% and -12 % per decade, respectively.

Nishio, Fumihiko↗

Low-Energy Parameters of Neutron–Neutron Interaction: Analysis of Data Obtained in nd and dd Breakup Reactions

Data obtained in recent years for the neutron–neutron scattering length in nd and dd breakup reactions are analyzed. Serious discrepancies between experimental data from different studies may be explained by the effect of three-nucleon forces depending on the velocity of separation of a neutron–neutron pair and a charged fragment. It is shown that the data under analysis can be approximated by a smooth curve representing the dependence of the scattering length on the parameter R, which determines the fragment-separation distance after a fixed time. This dependence makes it possible to obtain the scatteringlength value for R→∞—that is, in the absence of the effect of three-nucleon forces.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A Dynamical and Statistical Characterization of U.S. Extreme Precipitation Events and Their Associated Large-Scale Meteorological Patterns

Abstract Regional patterns of extreme precipitation events occurring over the continental United States are identified via hierarchical cluster analysis of observed daily precipitation for the period 1950–2005. Six canonical extreme precipitation patterns (EPPs) are isolated for the boreal warm season and five for the cool season. The large-scale meteorological pattern (LMP) inducing each EPP is identified and used to create a “base function” for evaluating a climate model’s potential for accurately representing the different patterns of precipitation extremes. A parallel analysis of the Community Climate System Model, version 4 (CCSM4), reveals that the CCSM4 successfully captures the main U.S. EPPs for both the warm and cool seasons, albeit with varying degrees of accuracy. The model’s skill in simulating each EPP tends to be positively correlated with its capability in representing the associated LMP. Model bias in the occurrence frequency of a governing LMP is directly related to the frequency bias in the corresponding EPP. In addition, however, discrepancies are found between the CCSM4’s representation of LMPs and EPPs over regions such as the western United States and Midwest, where topographic precipitation influences and organized convection are prominent, respectively. In these cases, the model representation of finer-scale physical processes appears to be at least equally important compared to the LMPs in driving the occurrence of extreme precipitation.

54 ENVIRONMENTAL SCIENCES↗