Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stack Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Conductive Metallophthalocyanine Framework Films with High Carrier Mobility as Efficient Chemiresistors

Abstract The poor electrical conductivity of two‐dimensional (2D) crystalline frameworks greatly limits their utilization in optoelectronics and sensor technology. Herein, we describe a conductive metallophthalocyanine‐based NiPc‐CoTAA framework with cobalt(II) tetraaza[14]annulene linkages. The high conjugation across the whole network combined with densely stacked metallophthalocyanine units endows this material with high electrical conductivity, which can be greatly enhanced by doping with iodine. The NiPc‐CoTAA framework was also fabricated as thin films with different thicknesses from 100 to 1000 nm by the steam‐assisted conversion method. These films enabled the detection of low‐concentration gases and exhibited remarkable sensitivity and stability. This study indicates the enormous potential of metallophthalocyanine‐based conductive frameworks in advanced stand‐off chemical sensors and provides a general strategy through tailor‐make molecular design to develop sensitive and stable chemical sensors for the detection of low‐concentration gases.

Yue, Yan↗

Conductive Metallophthalocyanine Framework Films with High Carrier Mobility as Efficient Chemiresistors

Abstract The poor electrical conductivity of two‐dimensional (2D) crystalline frameworks greatly limits their utilization in optoelectronics and sensor technology. Herein, we describe a conductive metallophthalocyanine‐based NiPc‐CoTAA framework with cobalt(II) tetraaza[14]annulene linkages. The high conjugation across the whole network combined with densely stacked metallophthalocyanine units endows this material with high electrical conductivity, which can be greatly enhanced by doping with iodine. The NiPc‐CoTAA framework was also fabricated as thin films with different thicknesses from 100 to 1000 nm by the steam‐assisted conversion method. These films enabled the detection of low‐concentration gases and exhibited remarkable sensitivity and stability. This study indicates the enormous potential of metallophthalocyanine‐based conductive frameworks in advanced stand‐off chemical sensors and provides a general strategy through tailor‐make molecular design to develop sensitive and stable chemical sensors for the detection of low‐concentration gases.

Yue, Yan↗

Magnetic characteristics of a high-layer-number NiFe/FeMn multilayer

We report the static and dynamic magnetic characteristics of a high-layer-number NiFe/FeMn multilayer test structure with potential applications in broadband absorber and filter devices. To allow fine control over the absorption linewidths and to understand the mechanisms governing the resonances in a tailored structure similar to that expected to be used in real world applications, the multilayer was intentionally designed to have layer thickness and interface roughness variations. Magnetometry measurements show that the sample has complex hysteresis loops with features consistent with single ferromagnetic film reversals. Characterisation by transmission electron microscopy allows us to correlate the magnetic properties with structural features, including the film widths and interface roughnesses. Analysis of resonance frequencies from broadband ferromagnetic resonance measurements as a function of field magnitude and orientation provide values of the local exchange bias, rotatable anisotropy, and uniaxial anisotropy fields for specific layers in the stack and explain the observed mode softening. The linewidths of the multilayer are adjustable around the bias field, approaching twice that seen at larger fields, allowing control over the bandwidth of devices formed from the structure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Transparent electrodes in silicon heterojunction solar cells: Influence on contact passivation

Charge carrier collection in silicon heterojunction solar cells occurs via intrinsic/doped hydrogenated amorphous silicon layer stacks deposited on the crystalline silicon wafer surfaces. Usually, both the electron and hole collecting stacks are externally capped by an n-type transparent conductive oxide, which is primarily needed for carrier extraction. Earlier, it has been demonstrated that the mere presence of such oxides can affect the carrier recombination in the crystalline silicon absorber. Here, we present a detailed investigation of the impact of this phenomenon on both the electron and hole collecting sides, including its consequences for the operating voltages of silicon heterojunction solar cells. As a result, we define guiding principles for improved passivating contact design for high-efficiency silicon solar cells.

14 SOLAR ENERGY↗

ExaWorks software development kit: a robust and scalable collection of interoperable workflows technologies

Scientific discovery increasingly requires executing heterogeneous scientific workflows on high-performance computing (HPC) platforms. Heterogeneous workflows contain different types of tasks (e.g., simulation, analysis, and learning) that need to be mapped, scheduled, and launched on different computing. That requires a software stack that enables users to code their workflows and automate resource management and workflow execution. Currently, there are many workflow technologies with diverse levels of robustness and capabilities, and users face difficult choices of software that can effectively and efficiently support their use cases on HPC machines, especially when considering the latest exascale platforms. We contributed to addressing this issue by developing the ExaWorks Software Development Kit (SDK). The SDK is a curated collection of workflow technologies engineered following current best practices and specifically designed to work on HPC platforms. We present our experience with (1) curating those technologies, (2) integrating them to provide users with new capabilities, (3) developing a continuous integration platform to test the SDK on DOE HPC platforms, (4) designing a dashboard to publish the results of those tests, and (5) devising an innovative documentation platform to help users to use those technologies. Our experience details the requirements and the best practices needed to curate workflow technologies, and it also serves as a blueprint for the capabilities and services that DOE will have to offer to support a variety of scientific heterogeneous workflows on the newly available exascale HPC platforms.

97 MATHEMATICS AND COMPUTING↗

3D Simulation of Missing Pellet Surface Defects in Light Water Reactor Fuel Rods

The cladding on light water reactor (LWR) fuel rods provides a stable enclosure for fuel pellets and serves as a first barrier against fission product release. Consequently, it is important to design fuel to prevent cladding failure due to mechanical interactions with fuel pellets. Cladding stresses can be effectively limited by controlling power increase rates. However, it has been shown that local geometric irregularities caused by manufacturing defects known as missing pellet surfaces (MPS) in fuel pellets can lead to elevated cladding stresses that are sufficiently high to cause cladding failure. Accurate modeling of these defects can help prevent these types of failures. Nuclear fuel performance codes commonly use a 1.5D (axisymmetric, axially-stacked, one-dimensional radial) or 2D axisymmetric representation of the fuel rod. To study the effects of MPS defects, results from 1.5D or 2D fuel performance analyses are typically mapped to thermo-mechanical models that consist of a 2D plane-strain slice or a full 3D representation of the geometry of the pellet and clad in the region of the defect. The BISON fuel performance code developed at Idaho National Laboratory employs either a 2D axisymmetric or 3D representation of the full fuel rod. This allows for a computational model of the full fuel rod to include local defects. A 3D thermo-mechanical model is used to simulate the global fuel rod behavior, and includes effects on the thermal and mechanical behavior of the fuel due to accumulation of fission products, fission gas production and release, and the effects of fission gas accumulation on thermal conductivity across the fuel-clad gap. Local defects can be modeled simply by including them in the 3D fuel rod model, without the need for mapping between two separate models. This allows for the complete set of physics used in a fuel performance analysis to be included naturally in the computational representation of the local defect, and for the effects of the local defect to be coupled with the global fuel rod model. This approach for modeling fuel with MPS defects is demonstrated and compared with alternative techniques. The effects of varying parameters of the MPS defect are studied using this technique and presented here.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Adaptive Waveform Correlation Detectors for Arrays: Algorithms for Autonomous Calibration

Waveform correlation detectors compare a signal template with successive windows of a continuous data stream and report a detection when the correlation coefficient, or some comparable detection statistic, exceeds a specified threshold. Since correlation detectors exploit the fine structure of the full waveform, they are exquisitely sensitive when compared to power (STA/LTA) detectors. The drawback of correlation detectors is that they require complete knowledge of the signal to be detected, which limits such methods to instances of seismicity in which a very similar signal has already been observed by every station used. Such instances include earthquake swarms, aftershock sequences, repeating industrial seismicity, and many other forms of controlled explosions. The reduction in the detection threshold is even greater when the techniques are applied to arrays since stacking can be performed on the individual channel correlation traces to achieve significant array gain. In previous years we have characterized the decrease in detection threshold afforded by correlation detection across an array or network when observations of a previous event provide an adequate template for signals from subsequent events located near the calibration event. Last year we examined two related issues: (1) the size of the source region calibration footprint afforded by a master event, and (2) the use of temporally incoherent detectors designed to detect the gross envelope structure of the signal to extend the footprint. In Case 1, results from the PETROBAR-1 marine refraction profile indicated that array correlation gain was usable at inter-source separations out to one or two wavelengths. In Case 2, we found that incoherent detectors developed from a magnitude 6 event near Svalbard were successful at detecting aftershocks where correlation detectors derived from individual aftershocks were not. Incoherent detectors might provide 'seed' events for correlation detectors that then could extend detection to lower magnitudes. This year we addressed a problem long known to limit the acceptance of correlation detectors in practice: the labor intensive development of templates. For example, existing design methods cannot keep pace with rapidly unfolding aftershock sequences. We successfully built and tested an object-oriented framework (as described in our 2005 proposal) for autonomous calibration of waveform correlation detectors for an array. The framework contains a dynamic list of detectors of several types operating on a continuous array data stream. The list has permanent detectors: beam forming power (STA/LTA) detectors which serve the purpose of detecting signals not yet characterized with a waveform template. The framework also contains an arbitrary number of subspace detectors which are launched automatically using the waveforms from validated power detections as templates. The implementation is very efficient such that the computational cost of adding subspace detectors was low. The framework contains a supervisor that oversees the validation of power detections, and periodically halts the processing to revise the portfolio of detectors. The process of revision consists of collecting the waveforms from all detections, performing cross-correlations pairwise among all waveforms, clustering the detections using correlations as a distance measure, then creating a new subspace detector from each cluster. The collection of new subspace detectors replaces the existing portfolio and processing of the data stream resumes. This elaborate scheme was implemented to prevent proliferation of closely-related subspace detectors. The method performed very well on several simple sequences: 2005 'drumbeat' events observed locally at Mt. St. Helens, and the 2003 Orinda, CA aftershock sequence. Our principal test entailed detection of the aftershocks of the San Simeon earthquake using the NVAR array; in this case, the system automatically detected and categorized approximately 2/3 of the events above magnitude 2.8.

58 GEOSCIENCES↗

Optimization-based approaches to control of connected and automated vehicles: Principles, complexities, applications, challenges, and outlook

Safe and optimal motion control for connected and automated vehicles (CAVs) poses a fundamental optimization challenge at the intersection of system complexity, environmental uncertainty, and stringent real-time constraints. Existing surveys address this challenge in isolation – focusing either on specific control techniques or individual uncertainty sources – without providing a unified framework that characterizes the trade-offs among computational tractability, performance verifiability, and adaptive generalization across paradigms. This review addresses that gap by presenting a cohesive analytical framework concentrated on the decision-making and trajectory optimization layers of the CAV autonomy stack. We systematically analyze three major optimization paradigms – first-principles model-based optimization, data-driven methods, and hybrid synergistic architectures – evaluating each against four core complexity axes: problem formulation, constraint handling, optimality guarantees, and robustness. Key applications including platooning, trajectory planning, collision avoidance, and cooperative control are examined to reveal recurring methodological patterns and critical operational constraints that limit real-world performance. Our synthesis identifies verifiable hybrid architectures, incentive-aligned multi-agent cooperation, and hardware-algorithm co-design as the defining research frontiers, and distills a targeted agenda for developing CAV control systems that are simultaneously safe, computationally efficient, and deployable in the full complexity of real-world traffic environments.

Muzahid, Abu Jafar Md [University of Tennessee, Kn↗

Layer-Dependent Bit Error Variation in 3-D NAND Flash Under Ionizing Radiation

In this paper, we studied the total ionization dose (TID) effects on the multilevel-cell (MLC) 3-D NAND flash memory using Co-60 gamma radiation. We found a significant page-to-page bit error variation within a physical memory block of the irradiated memory chip. Our analysis showed that the origin of the bit error variation is the unique vertical layer-dependent TID response of the 3-D NAND. We found that the memory pages located at the upper and lower layers of the 3-D stack show higher fails compared to the middle-layer pages of a given memory block. We confirmed our findings by comparing radiation response of four different chips of the same specification. In addition, we compared the TID response of the MLC 3-D NAND with that of the 2-D NAND chip, which showed less page-to-page variation in bit error within a given memory block. We discuss the possible application of our findings for the radiation-tolerant smart memory controller design.

3-D NAND flash↗

Sputtered p-Type Cu x Zn 1– x S Back Contact to CdTe Solar Cells

As thin-film cadmium telluride (CdTe) solar cells gain prominence, one particular challenge is optimizing contacts and their interfaces to transfer charge without losses in efficiency. Back contact recombination is still significant and will prevent CdTe solar technology from reaching its full potential in device efficiency, and transparent back contacts have not been developed for bifacial solar technology or multijunction solar cells. To address these challenges, here we investigate sputtered Cu x Zn 1– x S as a p-type semi-transparent back contact material to thin-film polycrystalline CdTe solar cells at Cu concentrations x = 0.30, 0.45, and 0.60. This material is selected for its high hole conductivity (160–2120 S cm –1 ), wide optical band gap (2.25–2.75 eV), and variable ionization potential (approximately 6–7 eV) that can be aligned to that of CdTe. We report that without device optimization, CdTe solar cells with these Cu x Zn 1– x S back contacts perform as well as control cells with standard ZnTe:Cu back contacts. We observe no reduction in external quantum efficiency, low contact barrier heights of approximately 0.3 eV, and carrier lifetimes on par with those of baseline CdTe. These cells are relatively stable over one year in air, with V OC and efficiency of the x = 0.30 cell decreasing by only 1 and 3%, respectively. Using scanning electron microscopy and scanning transmission electron microscopy to investigate the Cu x Zn 1– x S/CdTe interface, we demonstrate that the Cu x Zn 1– x S layer segregates into a bilayer of Cu-Te-S and Zn-Cd-S, and thermodynamic reaction calculations support these findings. Despite its bilayer formation, the back contact still functions well. This investigation explains some of the physical mechanisms governing the device stack, inspires future work to understand interfacial chemistry and charge transfer, and elicits optimization to achieve higher-efficiency CdTe cells.

14 SOLAR ENERGY↗

Microstructure and heteroatom dictate the doping mechanism and thermoelectric properties of poly(alkyl-chalcogenophenes)

Heteroatom substitution can favorably alter electronic transport in conductive polymers to improve their thermoelectric performance. Here we report the spectroscopic, structural, and thermoelectric properties of poly(3–(3',7'-dimethyloctyl) chalcogenophenes) or P3RX doped with 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ), where the heteroatom [X = thiophene (T), selenophene (Se), tellurophene (Te)], the doping methodology, and extent of doping are systematically varied. Spectroscopic measurements reveal that while all P3RX polymers are appreciably doped, the doping mechanism is inherently different. Poly(3-hexylthiophene) (P3HT, used as a control) and poly(3–(3',7'-dimethyloctyl)tellurophene) (P3RTe) are doped primarily via integer charge transfer (ICT), whereas poly(3–(3',7'-dimethyloctyl)selenophene) (P3RSe) and poly(3–(3',7'-dimethyloctyl)thiophene) (P3RT) are doped via charge transfer complex (CTC) mechanisms. Despite these differences, all polymers saturate with roughly the same number of F4TCNQ counterions (1 dopant per 4 to 6 heterocycles), reinforcing the idea that the extent of charge transfer varies with the doping mechanism. Grazing incidence wide-angle x-ray scattering measurements provide insight into the structural driving forces behind different doping mechanisms—P3RT and P3RSe have similar microstructures in which F4TCNQ intercalates between the π-stacked backbones resulting in CTC doping (localized carriers), while P3HT and P3RTe have microstructures in which F4TCNQ intercalates in the alkyl side chain region, giving rise to ICT doping (delocalized carriers). These structural and spectroscopic observations shed light on why P3HT and P3RTe obtain electrical conductivities ca. 3 S/cm, while P3RT and P3RSe have conductivities <10–3 S/cm under the same thin film processing conditions. Ultimately, this work quantifies the effects of heteroatom, microstructural ordering, extent of doping, and doping mechanism, thereby providing rational guidance for designing future thermoelectric polymer-dopant systems.

36 MATERIALS SCIENCE↗

Reducing Uncertainty in Hydrodynamic Modeling of ATR Experiments Via Flow Testing, Validation, and Optimization

The development, characterization, and qualification testing of nuclear fuel at Idaho National Laboratory’s Advanced Test Reactor (ATR) requires extensive design and analysis activities prior to the insertion of an irradiation experiment in-pile. Significant effort is made in the design and development phase of all in-pile experiments to ensure that the maximum feasible impacts of all necessary experimental requirements are satisfied. The advancement of fuel, cladding, and in-reactor materials technology in recent years has introduced complexities associated with the design and construct of in-pile experiments necessitating deeper understanding of boundary conditions and increasingly comprehensive observations resulting from the experiment. Each unique experiment must be assessed for neutronics response, thermal/hydraulic/hydrodynamic performance, and structural integrity. This is accomplished either analytically, computationally, or experimentally, or some combination thereof, prior to insertion into the ATR. The various effects are interrelated to various degrees, such as the case with the experiment temperature affecting the thermal cross section of the fuel or the increased temperature of the experiment’s materials reducing the mechanical strength of the assemblies. Additionally, the feedback between the experiment’s response to a reactor transient could alter the neutron flux profile of the reactor during the transient. Each experiment must therefore undergo a barrage of analyses to assure the ATR operational safety review committee that the insertion and irradiation of the experiment will not detrimentally affect the safe operational envelope of the reactor. In many cases, the nuclear fuel being tested can be double-encapsulated to ensure safety margins are adequately addressed, whereas failed fuel would be encased in a protective capsule. In other cases, the experiments can be inserted in a self-contained loop that passes through the reactor core, remaining isolated from the primary coolant. In the case of research reactor fuel, however, the fuel plates must be tested in direct contact with the reactor coolant, and being fuel designed for high neutron fluxes, they are inherently power-dense plates. The combination of plate geometry, high-power density, and direct contact with primary coolant creates a scenario where the neutronic/thermomechanic/hydrodynamic characteristics of the fuel plates are tightly coupled, necessitating as complete characterization as possible to support the safety and programmatic assessments, thus enabling a successful experiment. This paper explores the efforts of the U.S. High-Performance Research Reactor program to thermomechanically/hydromechanically characterize the program’s wide variety of experiments, which range from stacks of miniplate capsules to full-sized, geometrically representative curved plates. Special attention is given to instances where the combination of experimental characterization and analytical assessment has reduced uncertainties of the safety margins, allowing experiments to be irradiated that would otherwise not have passed the rigorous qualification process for irradiation in the ATR. In some cases, the combined processes have exposed flow and heat transfer characteristics that would have been missed using historical methods, which allows for more accurate and representative postirradiation assessments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Highly efficient small molecule multi-junction organic photovoltaic cells

A highly efficient multi junction photovoltaic device, such as a two, three, or four junction device, is disclosed. The multi-junction device may include a first subcell comprising a first photoactive region and a second subcell comprising a second photoactive region. The first and second photoactive regions are designed to minimize spectral overlap and maximize photocurrent across a broad absorption spectra, such as wavelengths ranging from 400 nm to 900 nm. The device may further include an inter-connecting layer, disposed between the first subcell and the second subcell, that is at least substantially transparent. By introducing a transparent interconnecting layer, a dual element (tandem) cell achieves a power conversion efficiency of 10.0±0.5%. By adding an additional (3rd) sub-cell that absorbs at the second order optical interference maximum within the stack. The triple junction cell significantly improves the quantum efficiency at shorter wavelengths, achieving a power conversion efficiency of 11.1±0.5%. Adding additional sub-cells has been shown to increase power conversion efficiency above 12%.

Che, Xiaozhou↗

Stacked Low-Inertia Converter or Solid-State Transformer: Modeling and Model Predictive Priority-Shifting Control for Voltage Balance

This paper presents control challenges of stacked low-inertia converter (SLIC) or cascaded reduced dc-link solid-state transformer (SST) and proposes a novel model predictive priority-shifting (MPPS) control with implicit modulator and a discrete-time large-signal model for voltage balancing and dc-link regulation. Low-inertia converters, featuring small electrolytic capacitor-less dc links, dramatically reduce cost, size, and weight compared to conventional solutions. However, without a large dc-link buffer, the input and output are tightly coupled, leading to significant control challenges. The control becomes even more challenging with these converters stacked input-series output-parallel (ISOP) for medium-voltage (MV) grid, which causes coupling between the modules besides the coupling within each module. This paper analyzes the multi-objective, multi-degree of freedom control problem, using the modular soft-switching solid-state transformer (M-S4T) as an example of the SLIC. First, distribution of control efforts under controller saturation is critical because multiple control objectives can be conflicting, especially when the module voltages are unbalanced and are being restored. The MPPS can shift the priorities to address this issue. Second, due to the low inertia and high dc-link ripple, classic space vector pulse-width modulation (SVPWM), average model with small-ripple assumption, and control design based on small-signal model cannot accurately modulate, model, and control the nonlinear reduced dc link. Therefore, a discrete-time large-signal model of the M-S4T is established to derive the predictive control in the MPPS. The MPPS and the PI control are compared in MV simulations to show the issue of applying the PI to the SLIC and the effectiveness of the MPPS for voltage balancing and dc-link regulation in a deadbeat manner. Finally, the proposed control is tested on a 5 kV ISOP SiC SST prototype to verify priority shifting to address controller saturation issue and fast and robust voltage balancing.

14 SOLAR ENERGY↗

Sequence-dependent self-assembly of supramolecular nanofibers in periodic dynamic block copolymers

Block copolymers (BCPs) can spontaneously self-assemble into various nanostructured morphologies which enable their diverse applications in selective membranes, polymer electrolytes, and optoelectronics. To expand the range of nanostructures accessible to block copolymers, we designed dynamic block copolymers (DBCPs) that combine the phase separation of traditional block copolymers with the supramolecular self-assembly of periodic dynamic polymers. We demonstrate that DBCPs synthesized with a periodic block sequence self-assemble into high aspect ratio supramolecular nanofibers with well-ordered PEG and PDMS domains, in contrast to those synthesized with a random sequence which do not form nanofibers but have disordered morphologies. The periodicity of the block sequence ensures regular placement of dynamic bonds along the polymer chain, which enables stacking of the hydrogen bonding units into ordered 1D supramolecular nanofibers and delays the onset of terminal flow by up to 60 °C compared to the random block sequence. The hierarchically assembled supramolecular nanofibers display complex mechanical and thermal phase behavior arising from the interplay between phase separation of the dissimilar polymer backbones and supramolecular interactions between dynamic bonds. Despite identical bulk composition, the periodic DBCPs demonstrate ionic conductivity values over two orders of magnitude higher than their random counterparts due to the formation of well-ordered, interconnected, high aspect ratio ion-transporting PEG domains. In conclusion, these results highlight the potential for DBCPs as an emerging material platform to achieve advanced, self-assembled nanostructured morphologies.

36 MATERIALS SCIENCE↗

Cybersecurity Workforce Training for SMR Integration into Distribution Grids: A Competency Framework and Containerized Hands-On Lab for the SMR/DER/Microgrid Boundary

Small modular reactors (SMRs) and microreactors are entering the U.S. distribution grid as synchronous generation on feeders designed for loads and inverter-based distributed energy resources (DERs). No existing cybersecurity training program addresses this intersection of nuclear operations, DER management, and operational technology security. As subcontractor to Iowa State University on the CyDERMS Center, Argonne analyzed the relevant standards and training landscape, translated the resulting gaps into a twelve-objective competency framework across distribution-operator and graduate-analyst role tracks, and built a containerized training lab using a ∼400-bus composite grid model behind a realistically simulated Modbus TCP SCADA stack. The analysis isolates the balance-of-plant / energy-management-system (BOP/EMS) boundary as the critical jurisdictional seam where, as of March 2026, neither NRC nor NERC CIP cleanly claims cybersecurity responsibility for distribution-connected SMRs. The framework maps each objective across NIST CSF 2.0, ISA/IEC 62443, NIST NICE Task–Knowledge–Skill statements, and NRC RG 5.71 awareness-and-training controls. The training lab implements operator-recognition assessment scenarios spanning grid-side disturbances and telemetry-layer anomalies.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Practical Considerations of Moisture in Baled Biomass Feedstocks

Agricultural residues make up a large portion of the immediately available biomass feedstock for renewable energy markets. Current collection and storage methods rely on existing feed and forage practices designed to preserve nutrients and properties of digestibility. Low-cost collection and storage practices that preserve carbohydrates across a range of inbound moisture contents are needed to assure the economic and technical success of the emerging biomass industry. This study examines the movement of moisture in storage and identifies patterns of migration resulting from several on-farm storage systems and their impacts on moisture measurement and dry matter recovery. Baled corn stover and energy sorghum were stored outdoors in uncovered, tarp-covered, or wrapped stacks and sampled periodically to measure moisture and dry matter losses. Interpolation between discrete sampling locations in the stack improved bulk moisture content estimates and showed clear patterns of accumulation and re-deposition. Atmospheric exposure, orientation, and contact with barriers (i.e., soil, tarp, and wrap surfaces) were found to cause the greatest amount of moisture heterogeneity within stacks. Although the bulk moisture content of many stacks remained in the range suitable for aerobic stability, regions of high moisture were sufficient to support microbial activity, thus support dry matter loss. Stack configuration, orientation, and coverage methods are discussed relative to impact on moisture management and dry matter preservation. Additionally, sample collection and data analysis are discussed relative to assessment at the biorefinery as it pertains to stability in storage, queuing, and moisture carried into processing.

09 BIOMASS FUELS↗

Early Beam Injection Scheme for the Fermilab Booster: A Path for Intensity Upgrade

Over the past decade, Fermilab has focused efforts on the intensity frontier physics and is committed to increase the average beam power delivered to the neutrino and muon programs substantially. Many upgrades to the existing injector accelerators, namely, the current 400 MeV LINAC and the Booster, are in progress under the Proton Improvement Plan (PIP). Proton Improvement Plan-II (PIP-II) proposes to replace the existing 400 MeV LINAC by a new 800 MeV LINAC, as an injector to the Booster which will increase Booster output power by nearly a factor of two from the PIP design value by the end of its completion. In any case, the Fermilab Booster is going to play a very significant role for nearly next two decades. In this context, I have developed and investigated a new beam injection scheme called "early injection scheme" (EIS) for the Booster with the goal to significantly increase the beam intensity output from the Booster thereby increasing the beam power to the HEP experiments even before PIP-II era. The scheme, if implemented, will also help improve the slip-stacking efficiency in the MI/RR. Here I present results from recent simulations, beam studies, current status and future plans for the new scheme.

43 PARTICLE ACCELERATORS↗