Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Morphology dependent electrochemical performance of sputter deposited Sn thin films

Graphical abstract: Smooth homogenous anode surface results in better electrochemical performance in terms of capacity and cycle life. Highlights: ► Controlling rate of deposition of Sn thin films for different surface morphology. ► Higher deposition rate results in poor capacity retention. ► Lower deposition rate of 0.25 nm s{sup −1} helps in higher capacity retention. ► Electrochemical performance correlated homogeneity and interparticle contact area. -- Abstract: This study deals with tailoring of the surface morphology, microstructure, and electrochemical properties of Sn thin films deposited by magnetron sputtering with different deposition rates. Scanning electron microscopy and atomic force microscopy are used to characterize the film surface morphology. Electrochemical properties of Sn thin film are measured and compared by cyclic voltammetry and charge–discharge cycle data at a constant current density. Sn thin film fabricated with a higher deposition rate exhibited an initial discharge capacity of 798 mAh g{sup −1} but reduced to 94 mAh g{sup −1} at 30th cycle. Film deposited with lower deposition rate delivered 770 mAh g{sup −1} during 1st cycle with improved capacity retention of 521 mAh g{sup −1} on 30th cycle. Comparison of electrochemical performances of these films has revealed important distinctions, which are associated with the surface morphology and hence on rate of deposition.

36 MATERIALS SCIENCE↗

Optimization Using Metamodeling in the Context of Integrated Computational Materials Engineering (ICME)

Predictive Design Technologies, LLC (PDT) proposed to employ Integrated Computational Materials Engineering (ICME) tools to help the manufacturing industry in the United States regain the competitive advantage in the global economy. ICME uses computational materials science tools within a holistic system in order to accelerate materials development, improve design optimization, and unify design and manufacturing. With the advent of accurate modeling and simulation along with significant increases in high performance computing (HPC) power, virtual design and manufacturing using ICME tools provide the means to reduce product development time and cost by alleviating costly trial-and-error physical design iterations while improving overall quality and manufacturing efficiency. To reduce the computational cost necessary for the large-scale HPC simulations and to make the methodology accessible for small and medium-sized manufacturers (SMMs), metamodels are employed. Metamodels are approximate models (functional relationships between input and output variables) that can reduce the simulation times by one to two orders of magnitude. In Phase I, PDT, partnered with Mississippi State University (MSU), demonstrated the feasibility of the proposed methodology by employing MSU?s internal state variable (ISV) plasticity-damage model with the help of metamodels to optimize the microstructure-process-property-cost for tube manufacturing processes used by Plymouth Tube Company (PTC), which involves complicated temperature and mechanical loading histories. PDT quantified the microstructure-property relationships for PTC?s SAE J525 electric resistance-welded cold drawn low carbon hydraulic 1010 steel tube manufacturing processes at seven different material states and calibrated the ISV plasticity material parameters to fit experimental tensile stress-strain curves. PDT successfully performed large scale finite element (FE) simulations in an HPC environment using the ISV plasticity model in Abaqus FE analyses of the tube forming, sizing, drawing, welding, and normalizing processes. The simulation results coupled with the manufacturing cost data were used to develop prototype metamodeling (quick response) codes which could be used to predict and optimize the microstructure-process-property-cost relationships. The developed ICME metamodeling toolkits are flexible enough to be applied to other manufacturing processes (e.g. forging, forming, casting, extrusion, rolling, stamping, and welding/joining) and metamodeling codes can run on laptop computers. Based on the work completed in Phase I, in Phase II, PDT proposes to continue to refine the ISV model by correlating and incorporating the uncertainties in the microstructure, mechanical testing, and modeling. Following the model refinement, FE analyses will be simulated and will provide even more realistic predictions as they include an appropriate window of uncertainty. Using the HPC output (FE analyses) as input, the quick-response metamodel codes will more accurately predict and optimize the microstructure-process-property-cost relationships. Furthermore, PDT propose to employ the ICME metamodeling toolkits to help develop a new tube product using entirely new high strength steel. The modeling of the high strength steel manufacturing process will replace the costly and time consuming trial-and-error methods that were used in the tubing industry previously. This simulation-based process prototyping will greatly benefit our industrial partners by opening up new market spaces due to new products with greater capabilities.

36 MATERIALS SCIENCE↗

Impact of Coating Defects on Performance of Coated Zirconium Cladding

Research on accident tolerant fuels (ATF) has started after the Fukushima accident [1–3]. While efforts have been expended on both fuel and cladding ATF concepts, the bulk of work has been devoted to improved cladding. The overarching goal of these approaches is to extend the coping time available during a severe accident before any event would result in release of radioactivity to the public. The most basic ATF cladding concept is obtained by applying a thin coating of highly corrosion-resistant material on the surface of a licensed zirconium cladding alloy. This thin coating is intended to not interfere with the neutronic or mechanical performance of the base cladding under normal operating conditions. Different coating materials, thicknesses, coating processes, process parameters, and testing methods have an impact on the microstructure and mechanical properties and therefore on the results of the applied investigation methods. These challenges have motivated an initial focus on demonstrating that the presence of coatings do not perturb the critical performance benchmarks of uncoated material. Ongoing lead test assembly irradiations of coated zirconium concepts in commercial reactions is intended to establish baseline performance in this regard in the coming years.

36 MATERIALS SCIENCE↗

The Chemical Nature of the Fiber/resin Interface in Composite Materials

Carbon fiber/epoxy resin composites are considered. The nature of the fiber structure and the interaction that occurs at the interface between fiber and matrix are emphasized. Composite toughness can be improved by increased axial tensile and compressive strengths in the fibers. The structure of carbon fibers indicates that the fiber itself can fail transversely, and different transverse microstructures could provide better transverse strengths. The higher surface roughness of lower modulus and surface-treated carbon fibers provides better mechanical interlocking between the fiber and matrix. The chemical nature of the fiber surface was determined, and adsorption of species on this surface can be used to promote wetting and adhesion. Finally, the magnitude of the interfacial bond strength should be controlled such that a range of composites can be made with properties varying from relatively brittle and high interlaminar shear strength to tougher but lower interlaminar shear strength.

Diefendorf, R. J.↗

Rapid Prototyping of Continuous Fiber Reinforced Ceramic Matrix Composites

For ceramics to be used as structural components in high temperature applications, their fracture toughness is improved by embedding continuous ceramic fibers. Ceramic matrix composite (CMC) materials allow increasing the overall operating temperature, raising the temperature safety margins, avoiding the need for cooling, and improving the damping capacity, while reducing the weight at the same time. They also need to be reliable and available in large quantities as well. In this paper, an innovative rapid prototyping technique to fabricate continuous fiber reinforced ceramic matrix composites is described. The process is simple, robust and will be widely applicable to a number of high temperature material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The results of mechanical properties and microstructural characterization are presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts at an order of magnitude lower cost than current CVI and PIP processes.

Vaidyanathan, R.↗

Rapid Prototyping of Continuous Fiber Reinforced Ceramic Matrix Composites

For ceramics to be used as structural components in high temperature applications, their fracture toughness is improved by embedding continuous ceramic fibers. Ceramic matrix composite (CMC) materials allow increasing the overall operating temperature, raising the temperature safety margins, avoiding the need for cooling, and improving the damping capacity, while reducing the weight at the same time. They also need to be reliable and available in large quantities as well. In this paper, an innovative rapid prototyping technique to fabricate continuous fiber reinforced ceramic matrix composites is described. The process is simple, robust and will be widely applicable to a number of high temperature material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The results of mechanical properties and microstructural characterization are presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts at an order of magnitude lower cost than current chemical vapor infiltration (CVI) and polymer impregnation and pyrolysis (PIP) processes.

Vaidyanathan, R.↗

High Strength Discontinuously Reinforced Aluminum For Rocket Applications

This study presents results on the development of a new aluminum alloy with very high strength and ductility. Five compositions of Al-Mg-Sc-Gd-Zr alloy were selected for this purpose. These alloys were also reinforced with 15 volume percent silicon-carbide and boron-carbide particles to produce Discontinuously Reinforced Aluminum (DRA) materials. Matrix alloys and DRA were processed using a powder metallurgy process. The helium gas atomization produced very fine powder with cellular-dentritic microstructure. The microstructure of matrix alloys showed fine Al3Sc based precipitate which provides significant strengthening in these alloys. DRA showed uniform distribution of reinforcement in aluminum matrix. DRA materials were tested at -320 F, 75 F in air and 7S F in gaseous hydrogen environments and matrix alloys were tested at 75 F in air. DRA showed high strengths in the range of 89-111 ksi (614-697 MPa) depending on alloy compositions and test environments. Matrix alloys had a good combination of strength, 84-89 ksi (579-621 MPa) and ductility, 4.5-6.5%. The properties of these materials can further be improved by proper control of processing parameters.

Pandey, A. B.↗

Tungsten Foils and Composites for Fusion Applications - Mechanical Testing

Tokamak fusion reactors ultimately should deliver safe, clean, and abundant energy provided that materials and plasma challenges continue to be overcome. Materials that can withstand large heat fluxes and mechanical loads while undergoing intense irradiation are needed for the plasma-facing components of these reactors and are still undergoing development. Tungsten composites are candidates for this purpose; they have low sputtering yields, high melting points, and may be more ductile than pure tungsten. However, the mechanical properties of tungsten composites are not yet well characterized. Tungsten foils produced using severe plastic deformation, e.g. cold rolling, have shown considerable promise for these applications as they may be more ductile than tungsten produced using powder metallurgy alone. Changes to the mechanical properties of tungsten foils have been suggested to be correlated with ultra-fine grained or nanocrystalline microstructures created by severe plastic deformation. Tungsten foils with larger amounts of plastic deformation, i.e. thinner foils, have been shown to have smaller grain sizes and a more pronounced texture in (100) <011>. The grain size and structure of foils with differing degrees of plastic deformation are therefore likely to differ significantly and the foils will likely exhibit very different mechanical properties. To fabricate tungsten foils into a useful structural material for high temperature fusion applications, layered composites are currently being examined. These composites integrate the excellent functional characteristics of tungsten foils with an interlayer such as steel that may improve ductility and toughness. To engineer and optimize layered composites, the mechanical properties of tungsten foils with differing thicknesses and degrees of plastic deformation must be characterized, both pre- and post-irradiation.

36 MATERIALS SCIENCE↗

Evaluation of Mn substitution for Ni in alumina-forming austenitic stainless steels

There has been increasing interest in the substitution of low-cost Mn for Ni in austenitic stainless steels due to the rising price of Ni. This paper investigates the possibility of such a substitution approach for the recently developed alumina (Al{sub 2}O{sub 3})-forming austenitic (AFA) class of heat-resistant stainless steels. Computational thermodynamic tools were utilized to predict the alloy composition range to maintain an austenitic matrix microstructure when Mn is substituted for Ni in the presence of Al, which is a strong body-centered-cubic (BCC) phase stabilizer. Phase equilibria, oxidation behavior, and creep properties of Fe-(10-14)Cr-(5--15)Mn-(4-12)Ni-(2.5-3)Al-Cu-Nb-C-B (in weight percent) based alloys were studied. The alloys based on Fe-14Cr-2.5Al-(5-9)Mn-(10-12)Ni exhibited the best balance of oxidation and creep resistance, which represents approximately 50% reduction in Ni content compared to previously developed AFA alloys. These low-Ni, high-Mn AFA alloys formed protective Al{sub 2}O{sub 3} scales up to 973-1073 K in air and at 923 K in air with 10% water vapor. Creep-rupture lives of the alloys under a severe screening condition of 1023 K and 100 MPa were in the 7.2 x 10{sup 5}-1.8 x 10{sup 6} s (200-500 h) range, which is comparable to or somewhat improved over that of type 347 stainless steel (Fe-18Cr-11Ni base).

36 MATERIALS SCIENCE↗

Tailoring Microstructure and Properties of a Superelastic Ti–Ta Alloy by Incorporating Spark Plasma Sintering with Thermomechanical Processing

A powder metallurgy Ti–35 at.% Ta alloy was produced using a spark plasma sintering process. The sintered alloy exhibited Ta-rich regions at a sintering temperature of 1100 °C. Complete diffusion of elemental powders was achieved via homogenization heat treatment at 1500 °C for 12 h, but the ductility declined drastically. The brittle behavior of the homogenized sample was due to the high-oxygen content, continuous grain boundary α-phase and high-angle grain boundaries. Excellent mechanical properties were achieved when hot forging was used along with preheating the homogenized specimen at 1100 °C. The mechanisms underlying this phenomenon were suppression of the solid grain boundary α-phase, high fraction of low-angle grain boundaries and dynamic recrystallization. Tensile strength improved to the maximum value of 868 MPa. The strain recovery ratio increased to 90% in the first cycle during a cyclic loading–unloading test. Incomplete strain recovery of the first cycle was due to the presence of the martensite phase (α″).

36 MATERIALS SCIENCE↗

Review of Solid State Consolidation Processing Techniques of ODS Steels (Hot Extrusion, Hot Isostatic Pressing, Spark Plasma Sintering, and Stir Friction Consolidation): Resulting Microstructures and Mechanical Properties

This paper reviews the solid-state consolidation processing techniques for Oxide Dispersion Strengthened steels and compares them in terms of the resulting microstructure and reported mechanical properties. Synthesis techniques include hot extrusion, hot isostatic pressing, spark plasma sintering and friction consolidation. The effects of process parameters on the resulting microstructures and performance are discussed for each technique. Average oxide size, average grain size, and porosity are compared across techniques, as well as mechanical strength and ductility. Across consolidation techniques where temperature can be controlled, a low sintering temperature with a high sintering pressure is favorable for keeping oxide sizes, grain sizes, and porosity low. The use of yttrium and titanium for oxide formation has been evidenced to reduce oxide sizes, and tungsten additions have been shown to improve strength. Current literature suggests that the more mature hot extrusion technique produces stronger steel with consistently fine oxides, while other alternative solid-state consolidation, while promising, offer margin for improvement.

36 MATERIALS SCIENCE↗

Role of Tartaric Acid in Chemical, Mechanical and Self-Healing Behaviors of a Calcium-Aluminate Cement Blend with Fly Ash F under Steam and Alkali Carbonate Environments at 270 °C

Tartaric acid (TA) changes short-term mechanical behavior and phase composition of sodium-metasilicate activated calcium-aluminate cement blend with fly ash, type F, when used as a set control additive to allow sufficient pumping time for underground well placement. The present work focuses on TA effect on self-healing properties of the blend under steam or alkali carbonate environments at 270 °C applicable to geothermal wells. Compressive strength recoveries and cracks sealing were examined to evaluate self-healing of the cement after repeated crush tests followed by two consecutive healing periods of 10 and 5 days at 270 °C. Optical and scanning electron microscopes, X-ray diffraction, Fourier Transform infrared and EDX measurements along with thermal gravimetric analyses were used to identify phases participating in the healing processes. Samples with 1% mass fraction of TA by weight of blend demonstrated improved strength recoveries and crack plugging properties, especially in alkali carbonate environment. This effect was attributed to silicon-rich (C,N)-A-S-H amorphous phase predominant in TA-modified samples, high-temperature stable zeolite phases along with the formation of tobermorite-type crystals in the presence of tartaric acid.

15 GEOTHERMAL ENERGY↗

Influence of composition on the microstructure and mechanical properties of a nickel-base superalloy single crystal

The effects of cobalt, tantalum, and tungsten contents on the microstructure and mechanical properties of single crystal Mar-M247 were investigated. Elevated temperature tensile and creep-rupture properties of 001 oriented single crystals were related to microstructural features of the alloys. Substitution of Ni for Co in the high refractory metal alloys increased the lattice mismatch, which was considered to be the cause of the increases in tensile and creep strength. Substitution of Ni for Ta caused large decreases in tensile strength and creep life, consistent with decreases in gamma prime volume fraction, lattice mismatch, and solid solution hardening. Substitution of W for Ta resulted in decreased life at high stresses, which was related to small decreases in mismatch and volume fraction. However, the W substitution resulted in improved life at low stresses, which was related to solid solution strengthening by W.

Nathal, M. V.↗

Influence of composition on the microstructure and mechanical properties of a nickel-base superalloy single crystal

The effects of cobalt, tantaium, and tungsten contents on the microstructure and mechanical properties of single crystal Mar-M247 were investigated. Elevated temperature tensile and creep-rupture properties of 001 oriented single crystals were related to microstructural features of the alloys. Substitution of Ni for Co in the high refractory metal alloys increased the lattice mismatch, which was considered to be the cause of the increases in tensile and creep strength. Substitution of Ni for Ta caused large decreases in tensile strength and creep life, consistent with decreases in gamma prime volume fraction, lattice mismatch, and solid solution hardening. Substitution of W for Ta resulted in decreased life at high stresses, which was related to small decreases in mismatch and volume fraction. However, the W substitution resulted in improved life at low stresses, which was related to solid solution strengthening by W.

Nathal, M. V.↗

Enzyme-Embedded, Microstructural Reactors for Industrial Biocatalysis

In this project we explored enzyme-catalyzed methane conversion to methanol. Industrial biological approaches to methane conversion using whole organisms are predicted to be more energy efficient than chemical approaches, but are limited by mass transfer of the gas phase reactants, methane and oxygen, to the organisms. We demonstrated that 3D printing the enzyme particulate Methane Mono Oxygenase (pMMO) embedded in a polymer can improve the kinetics of methane to methanol conversion. This improvement was likely due to the ability to increase the surface area of the catalytic material using 3D printing. We also demonstrated the first continuous use of pMMO in a flow-through reactor. In order to understand the fundamental kinetic properties of pMMO, we conducted an in-depth study of pMMO kinetics using analytical tools developed in our lab. Finally, we developed a new copolymer system that allowed tuning of the gas permeability of the biocatalytic material.

36 MATERIALS SCIENCE↗

Irradiation effects on microstructure change in nanocrystalline ceria – Phase, lattice stress, grain size and boundaries

With a wide variety of applications in numerous industries, ranging from biomedical to nuclear, ceramics such as ceria are key engineering materials. It is possible to significantly alter the materials functionality and therefore its applications by reducing the grain size to the nanometer size regime, at which point the unique varieties of grain boundaries and associated interfaces begin to dominate the material properties. Nanocrystalline films of cubic ceria deposited onto Si substrates have been irradiated with 3 MeV Au+ ions at temperatures of 300 and 400 K to evaluate their response to irradiation. It was observed that the films remained phase stable. Following a slight stress relief stage at low damage levels, the overall lattice is extremely stable up to high irradiation dose of ~34 displacements per atom. The grains were also observed to undergo a temperature-dependent grain growth process upon ion irradiation. This is attributed to a defect-driven mechanism in which the diffusion of defects from the collision cascade is critical. Formation of dislocations that terminate and stabilize at symmetric grain boundaries may be the limiting factor in the grain growth and overall energy reduction of the system. Utilizing ion modification, possible improvement of the adhesion of thin films and reduction of the probability of detrimental effects of stress-induced problems are discussed.

36 MATERIALS SCIENCE↗

Improvement of critical current density in thallium-based (Tl,Bi)Sr(1.6)Ba(0.4)Ca2Cu3O(x) superconductors

Epitaxial (Tl,Bi)Sr(1.6)Ba(0.4)Ca2Cu3O(x) ((Tl,Bi)-1223) thin films on (100) single crystal LaAlO3 substrates were synthesized by a two-step procedure. Phase development, microstructure, and relationships between film and substrate were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Resistance versus temperature, zero-field-cooled and field cooled magnetization, and transport critical current density (J(sub c)) were measured. The zero-resistance temperature was 105-111 K. J(sub c) at 77 K and zero field was greater than 2 x 10(exp 6) A/sq cm. The films exhibited good flux pinning properties.

Ren, Z. F.↗

Metal Fused Filament Fabrication of Titanium Alloy for In Space Manufacturing

NASA is developing materials and processes for the in-space manufacturing of many items for the International Space Station (ISS) and future exploration platforms. These new manufacturing processes will require the further development of current 3D printing processes to achieve high-performance metal parts within the power and space constraints of the ISS. Manufacturing Ti-6Al-4V alloy parts with 3D printing using a metal fused filament fabrication (MF3) process is an alternative process to the Direct Metal Laser Sintering (DMLS) of the metal powders additive manufacturing process. Our initial work fabricating Ti-6Al-4V parts from Ti-6Al-4V powder-binder feedstock and processed with the MF3 process has resulted in 95-97% sintered densities. The current development work of optimized sintered properties investigates the effects of variation in sintering time, temperature, and vacuum on the sintered properties of Ti-6Al-4V MF3 printed tensile bars. Sintered properties such as density, hardness, and tensile properties were characterized followed by microstructural and chemical (O/C/N) analysis to understand the role of sintering process on the ensuing material properties. Future development of the MF3 process will also involve investigation of the effects of micro-milling the Ti-64Al-4V powder to nanometer particle sizes and the investigation of laser sintering of the 3D printed devices. This new micro-milling technique will have broad application to other areas that require particle size reduction of hard metallic materials, such as Nuclear Thermal Propulsion and other NASA technologies. Laser sintering in lieu of high temperature thermal sintering should allow for significant power reduction and improved processing speeds.

sintering, alloys, 3D printing↗