Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter continuation method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

“The development of a through-plane reactive excitation technique for detection of pinholes in membrane-containing MEA sub-assemblies”

As markets for polymer-electrolyte-membrane fuel cells (PEMFC) expand, there continues to be a need for the development and implementation of in-line quality inspection techniques to enable high-volume manufacturing methods for membrane-electrode assemblies (MEAs). These techniques mitigate the potential impact of poor quality on the cost of MEA components by real-time identification of process-induced irregularities, which can result from the manufacturing process or subsequent handling of the material during assembly into a full MEA. A particular type of irregularity known to impact MEA lifetime is loss of membrane integrity, e.g. via a pinhole. In this work, we focus on development of a technique to detect pinholes in membrane-containing MEA sub-assemblies - as opposed to in just the membrane - using a reactive excitation strategy coupled with infrared thermography for detection. A specialized device is introduced and, using various MEA sub-assemblies, is shown to enable detection of pinholes in stationary samples. Multi-physics modeling is utilized to understand and predict the impact of various design and operational parameters of this technique. The feasibility of the technique is demonstrated through both modeling and in-situ results. For example, a detectable (≥1 degree C) thermal response for a membrane pinhole of approximately 90 um in diameter is measured in a fraction of a second. The observed detection time is considered to be appropriate for further exploration of the technique in an in-line configuration.

30 DIRECT ENERGY CONVERSION↗

Multiwalled carbon nanotubes in titania based nanocomposite as trap for photoexcitons for enhanced photocatalytic hydrogen production under solar light irradiation

Highlights: • Facile synthesis of FCNTs-TiO{sub 2} composite through wet impregnation method. • Parameters were optimized for enhanced photocatalytic hydrogen production under sunlight irradiation. • At optimal conditions nanocomposite showed 8 folds higher hydrogen efficiency than pristine TiO{sub 2}. • Functionalized carbon nanotubes acts as cocatalyst in this study. - Abstract: The impact of functionalized multiwalled carbon nanotubes in titania based nanocomposite for photocatalytic hydrogen production was investigated. Founctionalization experiments were carried out to remove amorphous carbon atttached to carbon nanotubes by strong acid treatment followed by calcination at desired temperature and time intervals. Materials characterization revealed that anatase TiO{sub 2} nanoparticles randomly dispersed onto the walls of one dimensional multiwalled carbon nanotubes with surface hydroxyl and carbonyl groups besides significant change in optical absorption. Photocatalytic activity was performed in aqueous glycerol solution under solar light and volume of hydrogen production was quantified using gas chromatography. Highest hydrogen production rate of 13,107 μmol·h{sup −1}·g{sup −1} of catalyst was recorded under optimized conditions due to cocatalyst role of functionalized carbon nanotubes. Here, photo electrons were trapped by carbon nanotubes for continuous hydrogen production through reduction reaction.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Sonora: A New Generation Model Atmosphere Grid for Brown Dwarfs and Young Extrasolar Giant Planets

Brown dwarf and giant planet atmospheric structure and composition has been studied both by forward models and, increasingly so, by retrieval methods. While indisputably informative, retrieval methods are of greatest value when judged in the context of grid model predictions. Meanwhile retrieval models can test the assumptions inherent in the forward modeling procedure. In order to provide a new, systematic survey of brown dwarf atmospheric structure, emergent spectra, and evolution, we have constructed a new grid of brown dwarf model atmospheres. We ultimately aim for our grid to span substantial ranges of atmospheric metallilcity, C/O ratios, cloud properties, atmospheric mixing, and other parameters. Spectra predicted by our modeling grid can be compared to both observations and retrieval results to aid in the interpretation and planning of future telescopic observations. We thus present Sonora, a new generation of substellar atmosphere models, appropriate for application to studies of L, T, and Y-type brown dwarfs and young extrasolar giant planets. The models describe the expected temperature-pressure profile and emergent spectra of an atmosphere in radiative-convective equilibrium for ranges of effective temperatures and gravities encompassing 200 less than or equal to T(sub eff) less than or equal to 2400 K and 2.5 less than or equal to log g less than or equal to 5.5. In our poster we briefly describe our modeling methodology, enumerate various updates since our group's previous models, and present our initial tranche of models for cloudless, solar metallicity, and solar carbon-to-oxygen ratio, chemical equilibrium atmospheres. These models will be available online and will be updated as opacities and cloud modeling methods continue to improve.

emergent spectra↗

Spatially quasi-periodic bifurcations from periodic traveling water waves and a method for detecting bifurcations using signed singular values

We present a method of detecting bifurcations by locating zeros of a signed version of the smallest singular value of the Jacobian. This enables the use of quadratically convergent root-bracketing techniques or Chebyshev interpolation to locate bifurcation points. Only positive singular values have to be computed, though the method relies on the existence of an analytic or smooth singular value decomposition (SVD). The sign of the determinant of the Jacobian, computed as part of the bidiagonal reduction in the SVD algorithm, eliminates slope discontinuities at the zeros of the smallest singular value. We use the method to search for spatially quasi-periodic traveling water waves that bifurcate from large-amplitude periodic waves. The water wave equations are formulated in a conformal mapping framework to facilitate the computation of the quasi-periodic Dirichlet-Neumann operator. We find examples of pure gravity waves with zero surface tension and overhanging gravity-capillary waves. In both cases, the waves have two spatial quasi-periods whose ratio is irrational. We follow the secondary branches via numerical continuation beyond the realm of linearization about solutions on the primary branch to obtain traveling water waves that extend over the real line with no two crests or troughs of exactly the same shape. The pure gravity wave problem is of relevance to ocean waves, where capillary effects can be neglected. Such waves can only exist through secondary bifurcation as they do not persist to zero amplitude. The gravity-capillary wave problem demonstrates the effectiveness of using the signed smallest singular value as a test function for multi-parameter bifurcation problems. This test function becomes mesh independent once the mesh is fine enough.

97 MATHEMATICS AND COMPUTING↗

Spatio-Temporal Data Analysis at Scale Using Models Based on Gaussian Processes

Gaussian processes are the most commonly used statistical model for spatial and spatio-temporal processes that vary continuously. They are broadly applicable in the physical sciences and engineering and are also frequently used to approximate the output of complex computer models, deterministic or stochastic. We undertook research related to theory, computation, and applications of Gaussian processes as well as some work on estimating extremes of distributions for which a Gaussian process assumption might be inappropriate. Our theoretical contributions include the development of new classes of spatial-temporal covariance functions with desirable properties and new results showing that certain covariance models lead to predictions with undesirable properties. To understand how Gaussian process models behave when applied to deterministic computer models, we derived what we believe to be the first significant results on the large sample properties of estimators of parameters of Gaussian processes when the actual process is a simple deterministic function. Finally, we investigated some theoretical issues related to maxima of observations with varying upper bounds and found that, depending on the circumstances, standard large sample results for maxima may or may not hold. Our computational innovations include methods for analyzing large spatial datasets when observations fall on a partially observed grid and methods for estimating parameters of a Gaussian process model from observations taken by a polar-orbiting satellite. In our application of Gaussian process models to deterministic computer experiments, we carried out some matrix computations that would have been infeasible using even extended precision arithmetic by focusing on special cases in which all elements of the matrices under study are rational and using exact arithmetic. The applications we studied include total column ozone as measured from a polar-orbiting satellite, sea surface temperatures over the Pacific Ocean, and annual temperature extremes at a site in New York City. In each of these applications, our theoretical and computational innovations were directly motivated by the challenges posed by analyzing these and similar types of data.

97 MATHEMATICS AND COMPUTING↗

Potential Refinement of the ICRF

The analysis and data used for the ICRF represented the state of the art in global, extragalactic, X/S band microwave astrometry in 1995. The same general analysis method was used to extend the ICRF with subsequent VLBI data in a manner consistent with the original catalog. Since 1995 there have been considerable advances in the geodetic/astrometric VLBI data set and in the analysis that would significantly improve the systematic errors, stability, and density of the next realization of the ICRS when the decision is made to take this step. In particular, data acquired since 1990, including extensive use of the VLBA, are of higher quality and astrometric utility because of changes in instrumentation, schedule design, and networks as well as specifically astrometric intent. The IVS (International VLBI Service for Geodesy and Astrometry) continues to devote a portion of its observing capability to systematic extension of the astrometric data set. Sufficient data distribution exists to select a better set of defining sources. Improvements in troposphere modeling will minimize known systematic astrometric errors while accurate modeling and estimation of station effects from loading and nonlinear motions will permit the reintegration of the celestial reference frame, terrestrial reference frame and Earth orientation parameters though a single VLBI solution. The differences between the current ICRF and the potential next realization will be described.

Ma, Chopo↗

Review of Laser Ablation Process for Single Wall Carbon Nanotube Production

Different types of lasers are now routinely used to prepare single wall carbon nanotubes (SWCNTs). The original method developed by researchers at Rice University utilized a "double pulse laser oven" process. A graphite target containing about 1 atomic percent of metal catalysts is ablated inside a 1473K oven using laser pulses (10 ns pulse width) in slow flowing argon. Two YAG lasers with a green pulse (532 nm) followed by an IR pulse (1064 nm) with a 50 ns delay are used for ablation. This set up produced single wall carbon nanotube material with about 70% purity having a diameter distribution peaked around 1.4 nm. The impurities consist of fullerenes, metal catalyst clusters (10 to 100 nm diameter) and amorphous carbon. The rate of production with the initial set up was about 60 mg per hour with 10Hz laser systems. Several researchers have used variations of the lasers to improve the rate, consistency and study effects of different process parameters on the quality and quantity of SWCNTs. These variations include one to three YAG laser systems (Green, Green and IR), different pulse widths (nano to microseconds as well as continuous) and different laser wavelengths (Alexandrite, CO, CO2, free electron lasers in the near to far infrared). It is noted that yield from the single laser (Green or IR) systems is only a fraction of the two laser systems. The yield seemed to scale up with the repetition rate of the laser systems (10 to 60 Hz) and depended on the beam uniformity and quality of the laser pulses. The shift to longer wavelength lasers (free electron, CO and CO2) did not improve the quality, but increased the rate of production because these lasers are either continuous (CW) or high repetition rate pulses (kHz to MHz). The average power and the peak power of the lasers seem to influence the yields. Very high peak powers (MegaWatts per square centimeter) are noted to increase ablation of bigger particles with reduced yields of SWCNTs. Increased average powers seem to help the conversion of the carbon from target into vapor phase to improve formation of nanotubes. The use of CW far infrared lasers reduced the need for the oven, at the expense of controlled ablation. Some of these variations are tried with different combinations and concentrations of metal catalysts (Nickel with Cobalt, Iron, Palladium and Platinum) different buffer gases (e.g. Helium); with different oven temperatures (Room temperature to 1473K); under different flow conditions (1 to 1000 kPa) and even different porosities of the graphite targets. It is to be noted that the original Cobalt and Nickel combination worked best, possibly because of improved carbonization with stable crystalline phases. The mean diameter and yield seemed to increase with increasing oven temperatures. Thermal conductivity of the buffer gas and flow conditions dictate the quality as well as quantity of the SWCNTs. Faster flows, lower pressures and heavier gases seem to increase the yields. This review will attempt to cover all these variations and their relative merits. Possible growth mechanisms under these different conditions will also be discussed.

Arepalli, Sivaram↗

Corrosion test of HTGR graphite with SIC coating - 18671

The application of SiC composite as a corrosion-resistive coating of graphite remains an important task for HTGR. Different methods and technologies have been developed for SiC-coatings of fuel and graphite frames to reduce their chemical corrosion/spraying and sorption capacity with respect to hydrogen. The use of such a coating would lead to some stabilization of the structure of carbon formations and their properties, which are changing in almost all HTGR operational regimes. This paper presents a study of the chemical interaction of the SiC gradient coating of the high-density IG-110 graphite with H{sub 2}O, O{sub 2}, CH{sub 4}, H{sub 2}, at pressures 1 and 100 Pa in a temperature range up to 1400 deg. C. The experiments at 100 Pa were conducted using mass spectrometry registration of time dependencies of partial pressure changes of the gas mixture, keeping the sample at a constant temperature (integral mode). Similar registrations at 1 Pa of moisture were made in differential mode (under continuous pump out) with 10 deg. C/min heating/cooling rate. The experimental results and microstructural study made it possible to get the parameters and peculiarities of the passive and the active corrosions of SiC and draw some conclusions about the level of the reduction of gas interaction with the bulk graphite due to SiC coating (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Premelting, fluctuations, and coarse-graining of water-ice interfaces

Using statistical field theory supplemented with molecular dynamics simulations, we consider premelting on the surface of ice as a generic consequence of broken hydrogen bonds at the boundary between the condensed and gaseous phases. A procedure for coarse-graining molecular configurations onto a continuous scalar order parameter field is discussed, which provides a convenient representation of the interface between locally crystal-like and locally liquid-like regions. A number of interfacial properties are straightforwardly evaluated using this procedure such as the average premelting thickness and surface tension. The temperature and system size dependence of the premelting layer thickness calculated in this way confirms the characteristic logarithmic growth expected for the scalar field theory that the system is mapped onto through coarse-graining, though remains finite due to long-ranged interactions. Finally, from explicit simulations the existence of a premelting layer is shown to be insensitive to bulk lattice geometry, exposed crystal face, and curvature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Single electron in a storage ring: a probe into the fundamental properties of synchrotron radiation and a powerful diagnostic tool

An experimental study of undulator radiation generated by a single electron was carried out at the Integrable Optics Test Accelerator (IOTA) storage ring at Fermilab. Photons were detected with a single-photon avalanche diode (SPAD) at an average rate of 20 kHz, corresponding to one detection every few hundred revolutions. Events were continuously recorded by a picosecond event timer for as long as 5 minutes at a time. The collected data were used to directly test the predictions of classical Poisson photostatistics. The study was motivated in part by a previous observation of sub-Poissonian statistics in a similar experiment with synchrotron radiation. In addition, we show that the time series of recorded events can be used to study the synchrotron motion of a single electron, yielding dynamical parameters such as the phase jitter of the radiofrequency cavity and the dependence of the synchrotron period on amplitude. Research plans for further experiments are also discussed.

47 OTHER INSTRUMENTATION↗

Model-independent particle accelerator tuning

We present a new model-independent dynamic feedback technique, rotation rate tuning, for automatically and simultaneously tuning coupled components of uncertain, complex systems. The main advantages of the method are: 1) It has the ability to handle unknown, time-varying systems, 2) It gives known bounds on parameter update rates, 3) We give an analytic proof of its convergence and its stability, and 4) It has a simple digital implementation through a control system such as the Experimental Physics and Industrial Control System (EPICS). Because this technique is model independent it may be useful as a real-time, in-hardware, feedback-based optimization scheme for uncertain and time-varying systems. In particular, it is robust enough to handle uncertainty due to coupling, thermal cycling, misalignments, and manufacturing imperfections. As a result, it may be used as a fine-tuning supplement for existing accelerator tuning/control schemes. We present multi-particle simulation results demonstrating the scheme’s ability to simultaneously adaptively adjust the set points of twenty two quadrupole magnets and two RF buncher cavities in the Los Alamos Neutron Science Center Linear Accelerator’s transport region, while the beam properties and RF phase shift are continuously varying. The tuning is based only on beam current readings, without knowledge of particle dynamics. We also present an outline of how to implement this general scheme in software for optimization, and in hardware for feedback-based control/tuning, for a wide range of systems.

42 ENGINEERING↗

Inter-digital capacitive sensor for evaluating cable jacket and insulation aging

An inter-digital capacitive (TDC) sensor has previously been used to measure dielectric properties of cable insulation polymer material when placed in direct contact with the insulation. Often cable insulation is covered by a polymer jacket. The dielectric properties of many cable jacket and insulation polymers are known to change due to thermal and radiation exposure-related damage. These dielectric properties frequently track with other measures of cable aging, such as tensile elongation-at-break and indenter modulus that have been broadly established as cable insulation polymer assessment methods. The external jacket of a cable is likely to have a different permittivity from the underlying insulation, and frequently the jacket material exhibits more severe damage than the insulation material due to environmental exposure. Because the jacket serves primarily to guard the cable during installation, as long as the underlying insulation condition is acceptable, the jacket condition is relatively unimportant in service. As part of a continuing program to develop and evaluate nondestructive examination methods that may be applied to cable condition assessment, a set of tools has been developed including (1) a parallel-plate sensor to directly measure the permittivity spectrum of flat sheet material and (2) an TDC and fixture to measure the effect of cable polymer dielectric property change on the sensor response. The TDC consists of two fork-like electrodes facing each other with the fork tines interspersed and separated by a small gap. The electrodes are printed on one side of a flexible substrate that can be conformed to the surface of a cylindrical cable, with tines parallel to the cable axis. The electrodes are connected to a broad-frequency-spectral impedance meter that senses the capacitance between the narrowly gapped electrode tines. This capacitance is known to vary as a function of the permittivity of any material in close proximity to the electrodes. By finite element modeling (FEM) and experimentation, this study investigates the effect of tine spacing and other design parameters associated with the TDC on the voltage (potential) distribution and electric field depth of penetration. The TDC measurement of an unshielded ethylene-propylene rubber (EPR)-insulated cable is shown to track with the degree of aging and quantities obtained by established methods. For jacketed cable systems, the TDC response is dominated by the jacket but, by analyzing measurements from TDC sensors with different depths-of-field penetration into the cable under test, the influence of the chlorinated polyethylene (CPE) cable jacket material degradation can be separated from an assessment of the cable insulation thereby enabling assessment of the insulation beneath/through the jacket.

Cable NDE, Interdigital Capacitance, Cable test↗

Selective Biosorption of Valuable Rare Earth Elements Among Co-Occurring Lanthanides

To meet the increasing demand for rare earth elements (REEs) essential for low carbon-intensity energy technologies, new methods are needed for selective REE extraction from unconventional resources. Only a few REEs have significant economic value, but isolation of target rare earths from co-occurring lanthanides is challenging due to their similar chemical behavior. We present a novel approach to enhance separation of specific REEs from lanthanide mixtures. Escherichia coli cells engineered with lanthanide binding tags (LBTs) were immobilized in nonadsorbing, permeable polyethylene glycol diacrylate beads and packed into continuous flow, fixed-bed columns. Breakthrough of 15 rare earths in the +3 oxidation state resulted in notable differences in adsorption selectivity, with greatest separation between europium (Eu) and lanthanum (La) due to competitive displacement. REE adsorption onto fixed-bed columns was predicted by coupling a surface complexation model to a calibrated one-dimensional dual porosity transport model that accounts for interbead advective and intrabead diffusive transport. A tradeoff between high-abundance, low-affinity native carboxyl sites and low-abundance, high-affinity engineered LBT sites dictates process recovery efficiency and selectivity. Key chemical and operational parameters are identified to maximize selective extraction of high-value lanthanides, achieving a threefold enhancement of Eu recovery relative to La in a mixed REE solution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design Report on the MiniFuel Instrumented Test Apparatus for Understanding Radiation Effects

Most nuclear fuels irradiations at Oak Ridge National Laboratory (ORNL) over the past decade have been conducted using MiniFuel—a static capsule design employing subscale fuel specimens to collect separate-effects irradiated fuel performance data. Irradiation conditions for MiniFuel experiments are predicted pre-test using reactor physics, and thermal models are verified post-irradiation via SiC dilatometry and various spectrometry methods. Relevant fuel performance parameters are also observed post-irradiation in a hot cell, thereby providing a single data point for each parameter representing the cumulative effects of the irradiation conditions. Substantially more data can be harvested from a single test and within a shorter duration by instrumenting irradiation vehicles and measuring desired quantities in situ. This report presents the design and analysis of the MiniFuel INstrumented Irradiation Test Apparatus for Understanding Radiation Effects (MINITAURE)—an instrumented test rig based on the separate-effects MiniFuel concept that aims to capture fission gas release (FGR) and thermal conductivity degradation of fuel specimens during irradiation in the High Flux Isotope Reactor (HFIR). MINITAURE will be integrated with the Materials Irradiation Facility (MIF) located in the HFIR building outside the reactor containment. The MIF will act as the instrumentation and control center for the experiment, enabling real-time feedback from in situ sensors and control of irradiation temperatures via a gas delivery system. Two unique capsule designs were developed to capture each phenomenon: the thermal conductivity capsule, which uses a thermopile method to estimate fuel specimen thermal conductivity, and the fission gas release capsule, which will have continuous flowing gas communication to high-purity germanium detectors that are housed in the MIF for monitoring FGR. This report details the reactor physics and heat transfer modeling activities that were used to inform the experiment design and predict capsule performance. It also describes out-of-pile activities conducted to stand up this new capability and verify the measurement techniques. Modeling efforts to date have demonstrated the feasibility of the in situ measurement techniques and supported the development of the MINITAURE assembly configuration. Out-of-pile testing of the thermal conductivity measurement shows promise in capturing relative changes in thermal conductivity. However, significant errors exist in the measured absolute value, posing a need for further refinement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Scaling Study of Microbially-Enhanced Methane Production From Coal (Mecbm): Optimizing Nutrient Delivery For Maximized Methane Production

Microbially-enhanced coalbed methane (MECBM) recovery is a novel method to stimulate gas production in CBM reservoirs. We first develop suitable nutrient recipes for native coals from sites each in the Illinois Basin and in the San Juan Basin. The optimal concentrations for statistically significant parameters are identified and the methane yields at laboratory scale are obtained (Part I & II). We then demonstrate the importance of replicating truly in-situ conditions for bio- gasification studies by investigating methane productivity in a core holder simulating in-situ conditions. Based on the experimental results, the resulting gas production correlates positively with the permeability of the samples. We examine the deliverability of engineered microbial solutions to promote coal bioconversion in coals and demonstrate that greater than milli-darcy permeability is required under in-situ stress conditions (Part III). This constraint is supplemented by imaging and a fractal-based characterization approach to evaluate changes in the physical properties of coal due to bio-gasification. High resolution SEM imaging is used to observe swelling of the coal matrix with sub-micron wide continuous pores observed to persist even after microbial treatment (IV). We explore the potential of generating, propping-open and sustaining the functionality of hydraulic fractures in coal using different fracturing fluids (Part V). The alteration of the nano-pore structure due to MECBM treatment is examined by using small angle X-ray scattering (SAXS) to define the in-situ porosity evolution as a proxy to infer permeability evolution (Part VI). Coupled hydro-mechanical and bio-gasification modeling is applied to determine the effectiveness of nutrient delivery by hydraulic fracturing and its field implementation. Compared with both the unstimulated and hydro-shear-dilated cases of the natural fracture network, hydraulic fracturing demonstrates a significant improvement to enhance nutrient delivery. A preliminary analysis of field-scale methane yield is completed with consideration of the combined influence of permeability evolution, solute transport and microbial growth (Part VII). Developing nutrient solutions for Illinois Basin and San Juan Basin (Task 2): To enhance methane release from coal through bio-gasification, suitable nutrient solutions are needed to stimulate microbial activities toward coal depolymerization and conversion to biogas. Specific for bituminous coal in the Illinois basin, a nutrient recipe that can be used to enhance coal bio- gasification in situ is developed. Based on our previous experience working with Illinois coal and the characteristics of the formation water and the indigenous microbial community, four parameters, Fe powder, methanol, ethanol, and trace minerals are optimized through using a Box-Behnken design. The optimal condition predicted by the models is: Fe-powder at 74 mM, methanol at 97.91 mM, ethanol at 100 mM, and trace minerals at 100%. Under these conditions, the predicted methane yield and content is 1,417.35 ft 3 /ton and 80.7%, respectively. These results are then validated by experimental studies. In addition, each added component is evaluated in terms of its contribution to methane generated. Specifically, the role of coal in the bio-gasification process is studied against two other solid materials. Experimental data from different solid matrices prove that coal is indeed degraded by the studied microbial community.

01 COAL, LIGNITE, AND PEAT↗

Metal Big Area Additive Manufacturing: Process Modeling and Validation

Metal Big Area Additive Manufacturing (mBAAM) is a new additive manufacturing (AM) technology for printing large-scale 3D objects. mBAAM is based on the gas metal arc welding process and uses a continuous feed of welding wire to manufacture an object. An electric arc forms between the wire and the substrate, which melts the wire and deposits a bead of molten metal along the predetermined path. In general, the welding process parameters and local conditions determine the shape of the deposited bead. The sequence of the bead deposition and the corresponding thermal history of the manufactured object determine the long range effects, such as thermal-induced distortions and residual stresses. Therefore, the resulting performance or final properties of the manufactured object are dependent on its geometry and the deposition path, in addition to depending on the basic welding process parameters. Physical testing is critical for gaining the necessary knowledge for quality prints, but traversing the process parameter space in order to develop an optimized build strategy for each new design is impractical by pure experimental means. Computational modeling and optimization may accelerate development of a build process strategy and saves time and resources. Because computational modeling provides these opportunities, we have developed a physics-based Finite Element Method (FEM) simulation framework and numerical models to support the mBAAM process s development and design. In this paper, we performed a sequentially coupled heat transfer and stress analysis for predicting the final deformation of a small rectangular structure printed using the mild steel welding wire. Using the new simulation technologies, material was progressively added into the FEM simulation as the arc weld traversed the build path. In the sequentially coupled heat transfer and stress analysis, the heat transfer was performed to calculate the temperature evolution, which was used in a stress analysis to evaluate the residual stresses and distortions. In this formulation, we assume that physics is directionally coupled, i.e. the effect of stress of the component on the temperatures is negligible. The experiment instrumentation (measurement types, sensor types, sensor locations, sensor placements, measurement intervals) and the measurements are presented. The temperatures and distortions from the simulations show good correlation with experimental measurements. Ongoing modeling work is also briefly discussed.

Additive Manufacturing↗

Rythmos: Solution and Analysis Package for Differential-Algebraic and Ordinary-Differential Equations

Time integration is a central component for most transient simulations. It coordinates many of the major parts of a simulation together, e.g., a residual calculation with a transient solver, solution with the output, various operator-split physics, and forward and adjoint solutions for inversion. Even though there is this variety in these transient simulations, there is still a common set of algorithms and procedures to progress transient solutions for ordinary-differential equations (ODEs) and differential-alegbraic equations (DAEs). Rythmos is a collection of these algorithms that can be used for the solution of transient simulations. It provides common time-integration methods, such as Backward and Forward Euler, Explicit and Implicit Runge-Kutta, and Backward-Difference Formulas. It can also provide sensitivities, and adjoint components for transient simulations. Rythmos is a package within Trilinos, and requires some other packages (e.g., Teuchos and Thrya) to provide basic time-integration capabilities. It also can be coupled with several other Trilinos packages to provide additional capabilities (e.g., AztecOO and Belos for linear solutions, and NOX for non-linear solutions). The documentation is broken down into three parts: Theory Manual, User's Manual, and Developer's Guide. The Theory Manual contains the basic theory of the time integrators, the nomenclature and mathematical structure utilized within Rythmos, and verification results demonstrating that the designed order of accuracy is achieved. The User's Manual provides information on how to use the Rythmos, description of input parameters through Teuchos Parameter Lists, and description of convergence test examples. The Developer's Guide is a high-level discussion of the design and structure of Rythmos to provide information to developers for the continued development of capabilities. Details of individual components can be found in the Doxygen webpages.

97 MATHEMATICS AND COMPUTING↗

AM Powder Flowability Capabilities at NASA Marshall Space Flight Center (MSFC)

Additive Manufacturing (AM) powder flowability is critical to metal 3D printing, because the more fluid the powder is, the better powder spreads. The NASA MSFC’s Contamination Control Team (CCT) studies density, flow, particle size distribution, and morphology for programs such as Moon-to-Mars Planetary Autonomous Construction Technology (MMPACT), ASTM Proficiency Testing for AM and Powder Metallurgy, and MSFC’s AM team. Examining and measuring powder characteristics is essential for improving flowability of AM powder and ensuring lot-to-lot consistency, which will help to prevent defects in manufactured parts. The CCT uses several methods to characterize AM powder. Optical particle size distribution and morphology analyses determine particle parameters including size, circularity, convexity, and dimensions. The Carney and Hall Flowmeter Funnel measures time it takes powder to flow through a funnel to compare relative flowability (free-flowing and non-free-flowing). In addition to this, the device utilizes a density cup which determines apparent density. Lastly, the Revolution Powder Analyzer measures dynamic powder flowability and behavior over time via digital imaging. Using the CCT’s lab, the team has produced ASTM Powder Proficiency Testing results with flow rates, apparent density, particle size distribution, and tap density on titanium-based and nickel-based powder and compared data with other companies/labs. Morphology data was also collected for various regolith simulant powder for the MMPACT program. Lastly, the CCT used morphology data to examine the flowability of Inconel 718 powder for Selective Laser Melting (SLM) and Directed Energy Deposition (DED) printers at MSFC. The CCT’s essential work in studying and enabling AM powder characterization has helped and will continue to help study new and refined powders in the AM industry.

Additive Manufacturing↗