Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Design and testing of a high power spacecraft thermal management system

The design and test results are presented of an ammonia hybrid capillary pumped loop thermal control system which could be used for heat acquisition and transport on future large space platforms and attached payloads, such as those associated with the NASA Space Station. The High Power Spacecraft Thermal Management System (HPSTM) can operate as either a passive, capillary pumped two phase thermal control system, or, when additional pressure head is required, as a mechanically pumped loop. Testing has shown that in the capillary mode, the HPSTM evaporators can acquire a total heat load of between 600 W and 24 kW, transported over 10 meters, at a maximum heat flux density of 4.3 W/sq cm. With the mechanical pump circulating the ammonia, a heat acquisition potential of 52 kW was demonstrated for 15 minutes without an evaporator failure. These results represent a significant improvement over the maximum transport capability previously displayed in other capillary systems. The HPSTM system still retains the proven capillary capabilities of heat load sharing and flow control between evaporator plates, rapid power cycling, and nonuniform heating in both the capillary and hybrid operating modes.

Mccabe, Michael E., Jr.↗

STTR Phase I: Low-Cost, High-Accuracy, Whole-Building Carbon Dioxide Monitoring for Demand Control Ventilation

This STTR Phase I project assessed the feasibility of a new CO 2 sensing system optimized for low-cost, high-accuracy, whole-building monitoring for use in demand control ventilation. The focus was on the development of a wireless networking platform and associated firmware to provide signal conditioning and conversion, fault- and disruptiontolerant networking, and multi-hop routing at building scales to avoid wiring costs. Early exploration of a bridge (or “gateway”) to direct digital control services was also explored. Results of the project contributed to an improved understanding of a new electrochemical sensor for monitoring indoor CO 2 concentrations, as well as the electronics and networking infrastructure required to deploy those sensors at building scales. New knowledge was acquired concerning the sensor’s accuracy, environmental response, and failure modes, and the acquisition electronics required to achieve accuracy over a wide range of CO 2 concentrations. The project demonstrated that the new sensor offers repeatable correspondence with commercial optical sensors, with supporting electronics that offer gain accuracy within 0.5%, and acquisition accuracy within 1.5% across three orders of magnitude variation in generated current. Considering production, installation, and maintenance costs, the technology presents a foundation for achieving whole-building CO 2 sensing at a price point below $0.066 / sq-ft – meeting economic feasibility criteria established by the Department of Energy. The technology developed under this award addresses obstacles on the critical path to enabling whole-building CO 2 sensing and demand control ventilation in commercial retrofits, small commercial buildings, residential complexes, and other highpotential structures that have been slow to adopt these technologies. It presents an opportunity to significantly reduce energy use throughout the United States.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Insulator–metal transition induced by electric voltage in a ruthenate Mott insulator

We report the observation of electric-voltage induced insulator–metal phase transition in a ruthenate Mott insulator Ca 3 (Ru 0.9 Ti 0.1 ) 2 O 7 . We show that the electric field effect dominates and leads to a sharp phase transition at measurement temperatures far below the Mott transition, whereas the thermal effect becomes more significant and broadens the phase transition as the measurement temperature approaches the insulator–metal transition. Here, the electric field induced insulator–metal transition is presumably attributed to the avalanche breakdown of the correlated insulating state when driven out of equilibrium. This work highlights the strategy of using electric voltage to control the phase transition of this system in addition to other nonthermal parameters such as magnetic field and pressure reported previously.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An Uncertainty and Disturbance Estimator Based Voltage Control for Dual-Active-Bridge Converters

Nonlinearities and external disturbances, like deadtime effect, the on-state voltage drop of the power device, and load variations, can lead to tracking errors in the output voltage of dual-active-bridge (DAB) converters. To address these issues, first of all, a generic dynamic model for DAB converters is proposed, which integrates the DAB circuit model with the phase-shift control scheme. Then, an uncertainty and disturbance estimator (UDE) based voltage control scheme for DAB converters is proposed to improve the output tracking accuracy and dynamic performance. Using the proposed power model, the design procedure of the UDE controller is significantly simplified. Hardware-in-the-loop simulations as well as experimental studies on a scale-down prototype are performed to demonstrate the enhanced tracking and disturbance rejection performance of the proposed controller.

Wu, Yuheng↗

Controlling the Temperature and Speed of the Phase Transition of VO 2 Microcrystals

Here, we investigated the control of two important parameters of vanadium dioxide (VO 2 ) microcrystals, the phase transition temperature and speed, by varying microcrystal width. By using the reflectivity change between insulating and metallic phases, phase transition temperature is measured by optical microscopy. As the width of square cylinder-shaped microcrystals decreases from ~70 to ~1 μm, the phase transition temperature (67 °C for bulk) varied as much as 26.1 °C (19.7 °C) during heating (cooling). In addition, the propagation speed of phase boundary in the microcrystal, i.e., phase transition speed, is monitored at the onset of phase transition by using the high-speed resistance measurement. The phase transition speed increases from 4.6 × 10 2 to 1.7 × 10 4 μm/s as the width decreases from ~50 to ~2 μm. While the statistical description for a heterogeneous nucleation process explains the size dependence on phase transition temperature of VO 2 , the increase of effective thermal exchange process is responsible for the enhancement of phase transition speed of small VO 2 microcrystals. These findings not only enhance the understanding of VO 2 intrinsic properties but also contribute to the development of innovative electronic devices.

36 MATERIALS SCIENCE↗

Neural control of magnetic suspension systems

The purpose of this research program is to design, build and test (in cooperation with NASA personnel from the NASA Langley Research Center) neural controllers for two different small air-gap magnetic suspension systems. The general objective of the program is to study neural network architectures for the purpose of control in an experimental setting and to demonstrate the feasibility of the concept. The specific objectives of the research program are: (1) to demonstrate through simulation and experimentation the feasibility of using neural controllers to stabilize a nonlinear magnetic suspension system; (2) to investigate through simulation and experimentation the performance of neural controllers designs under various types of parametric and nonparametric uncertainty; (3) to investigate through simulation and experimentation various types of neural architectures for real-time control with respect to performance and complexity; and (4) to benchmark in an experimental setting the performance of neural controllers against other types of existing linear and nonlinear compensator designs. To date, the first one-dimensional, small air-gap magnetic suspension system has been built, tested and delivered to the NASA Langley Research Center. The device is currently being stabilized with a digital linear phase-lead controller. The neural controller hardware is under construction. Two different neural network paradigms are under consideration, one based on hidden layer feedforward networks trained via back propagation and one based on using Gaussian radial basis functions trained by analytical methods related to stability conditions. Some advanced nonlinear control algorithms using feedback linearization and sliding mode control are in simulation studies.

Gray, W. Steven↗

Condensed phase details in the time-independent combustion of AP/composite propellants

The problem of nonmetallized ammonium perchlorate (AP)/composite propellant combustion is studied with the aim of coherently interpreting apparently diverse experimental data. Three fundamental hypotheses are introduced: the extent of propellant degradation at the vaporization step has to be specified through a scientific criterion; condensed phase degradation of AP to vaporizable fragments is the overall rate-limiting reaction; the rate of combustion in the gas phase is controlled by diffusive-mixing processes. Theoretical predictions of the regression rates of AP are seen to match well with experimental observations. Theoretical curves of regression rate are presented for a typical composite propellant. It is seen through analyses that either of the two familiar models for the gas phase (flame sheet approximation and uniform combustion) describes the general behavior adequately, hence de-emphasizing the role of gas phase details in propellant combustion.

Kumar, R. N.↗

Triple voltage dc-to-dc converter and method

A circuit and method of providing three dc voltage buses and transforming power between a low voltage dc converter and a high voltage dc converter, by coupling a primary dc power circuit and a secondary dc power circuit through an isolation transformer; providing the gating signals to power semiconductor switches in the primary and secondary circuits to control power flow between the primary and secondary circuits and by controlling a phase shift between the primary voltage and the secondary voltage. The primary dc power circuit and the secondary dc power circuit each further comprising at least two tank capacitances arranged in series as a tank leg, at least two resonant switching devices arranged in series with each other and arranged in parallel with the tank leg, and at least one voltage source arranged in parallel with the tank leg and the resonant switching devices, said resonant switching devices including power semiconductor switches that are operated by gating signals. Additional embodiments having a center-tapped battery on the low voltage side and a plurality of modules on both the low voltage side and the high voltage side are also disclosed for the purpose of reducing ripple current and for reducing the size of the components.

42 ENGINEERING↗

Radio-Frequency Rapid Thermal Processing Enabling Spatial Phase Transformation and Nanocrystallization of Soft Magnetic Amorphous Alloys

Thermal processing of soft magnetic amorphous and nanocrystalline alloys is explored under the influence of radio-frequency induction-heating techniques. Direct induction-heating concepts based on longitudinal and transverse flux heating are examined and the details of electromagnetic fields interaction with metallic strips are discussed by analytical calculations as well as finite element analysis. Initial experimental results confirming spatial control of phase transformations and nanocrystallization within a single strip of Finemet Fe-based amorphous ribbons are reported. Here, the degree to which primary and secondary crystallization temperature are achieved depends on the spacing between the ribbon relative to the induction coil as well as the coil design and configuration. For transverse coil configurations, the local temperature and therefore microstructural evolution is different across the lateral dimension of processed ribbons, with reduced gap sizes producing enhanced peak temperatures and larger temperature distributions with greater spatial variation in microstructure. In addition, indirect susceptor-based induction heating under tension is performed and the impact of microstructure is demonstrated. Herein, potential for exploiting spatially optimized phase transformations is illustrated through electromagnetic field–assisted processing in a scalable manufacturing process with amorphous and nanocrystalline soft magnetic alloys.

36 MATERIALS SCIENCE↗

Strain-tunable topological quantum phase transition in buckled honeycomb lattices

Low-buckled silicene is a prototypical quantum spin Hall insulator with the topological quantum phase transition controlled by an out-of-plane electric field. We show that this field-induced electronic transition can be further tuned by an in-plane biaxial strain ε, owing to the curvature-dependent spin-orbit coupling (SOC): There is a Z{sub 2} = 1 topological insulator phase for biaxial strain |ε| smaller than 0.07, and the band gap can be tuned from 0.7 meV for ε=+0.07 up to 3.0 meV for ε=−0.07. First-principles calculations also show that the critical field strength E{sub c} can be tuned by more than 113%, with the absolute values nearly 10 times stronger than the theoretical predictions based on a tight-binding model. The buckling structure of the honeycomb lattice thus enhances the tunability of both the quantum phase transition and the SOC-induced band gap, which are crucial for the design of topological field-effect transistors based on two-dimensional materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Modification by food of the calcium absorbability and physicochemical effects of calcium citrate

The food-calcium (Ca) interaction was examined in 12 healthy women (mean age 38 years) maintained on a constant metabolic diet. They underwent three phases of study, comprised of control (no Ca), Ca citrate (1 g Ca/day) during meals, and Ca citrate separately from meals. Each phase was 7 days in length and two 24-hour urine samples were collected on days 6 and 7. The rise from the control phase in urinary Ca was slightly more prominent when Ca citrate was given with meals than without (68 and 62%, respectively). The fall in urinary phosphorus was equivalent at about 25% between Ca citrate phases. The rise in urinary citrate and pH and the decline in urinary ammonium were more prominent when Ca citrate was given with meals; however, the changes were small or nonsignificant. The urinary saturation of Ca oxalate, brushite or monosodium urate did not differ between the two Ca citrate phases. There was a nonsignificant rise in serum iron during Ca citrate phases. The results suggest that: 1) dissolution and absorption of Ca citrate might be slightly greater when given with food than without; 2) that the ability of Ca citrate to attenuate crystallization of stone-forming Ca salts in urine is not modified by food; and 3) that Ca citrate may not impair iron absorption from food.

Non-NASA Center↗

Lambda-scheme feedback spectroscopy

We report a theoretical investigation of a control scheme of a single-Λ system in pump–probe feedback spectroscopy. The feedback controls the phase of one of the fields, and its action is triggered by a nontrivial unraveling of the quantum operation of detection of spontaneous photons emitted by an atom. Within the framework of Markovian master equations, it is shown that the shape and width of the ‘dark’ resonance of coherent population trapping can be controlled within very wide limits. In addition, sharp resonant-like structures in the field’s work dependence on the Rabi frequencies are revealed and explained. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Improvement of the thermal stability of nickel silicide using a ruthenium interlayer deposited via remote plasma atomic layer deposition

In this study, the effects of a thin Ru interlayer on the thermal and morphological stability of NiSi have been investigated. Ru and Ni thin films were deposited sequentially to form a Ni/Ru/Si bilayered structure, without breaking the vacuum, by remote plasma atomic layer deposition (RPALD) on a p-type Si wafer. After annealing at various temperatures, the thermal stabilities of the Ni/Ru/Si and Ni/Si structures were investigated by various analysis techniques. The results showed that the sheet resistance of the Ni/Ru/Si sample was consistently lower compared to the Ni/Si sample over the entire temperature range. Although both samples exhibited the formation of NiSi{sub 2} phases at an annealing temperature of 800 °C, as seen with glancing angle x-ray diffraction, the peaks of the Ni/Ru/Si sample were observed to have much weaker intensities than those obtained for the Ni/Si sample. Moreover, the NiSi film with a Ru interlayer exhibited a better interface and improved surface morphologies compared to the NiSi film without a Ru interlayer. These results show that the phase transformation of NiSi to NiSi{sub 2} was retarded and that the smooth NiSi/Si interface was retained due to the activation energy increment for NiSi{sub 2} nucleation that is caused by adding a Ru interlayer. Hence, it can be said that the Ru interlayer deposited by RPALD can be used to control the phase transformation and physical properties of nickel silicide phases.

36 MATERIALS SCIENCE↗

SU-E-U-02: The Development of a Practical Ultrasonic System for Cross-Sectional Imaging of Small Animals

Purpose: To test the feasibility of developing a practical medium frequency ultrasound tomography method for small animal imaging. The ability to produce cross-sectional or full body images of a live small animal using a low-cost tabletop ultrasound scanner without any special license would be very beneficial to long term biological studies, where repeated scanning is often required over an extended period of time. Methods: The cross sectional images were produced by compounding multiple B-scans of a laboratory phantom or an animal acquired at different projection angles. Two imaging systems were used to test the concept. The first system included a programmable 64-channel phased array controller driving a 128-channel, 5–10 MHz linear probe to produce 143 B-Mode projections of the spinning object. The second system designed and manufactured in house, produced 64 or 128 B-Mode projections with a single unfocused 8 MHz transducer scanning with a 0.116 mm step size. Results: The phased array system provided good penetration through the phantoms/mice (with the exception of the lungs) and allowed to acquire data in a very short time. The cross-sectional images have enough resolution and dynamic range to detect both high- and low-contrast organs. The single transducer system takes longer to scan, and the data require more sophisticated processing. To date, our images allow seeing details as small as 1–2 mm in the phantoms and in small animals, with the contrast mostly due to highly reflecting bones and air inclusions. Conclusion: The work indicates that very detailed and anatomically correct images can be created by relatively simple and inexpensive means. With more advanced algorithms and improved system design, scan time can be reduced considerably, enabling high-resolution full 3D imaging. This will allow for quick and easy scans that can help monitor tumor growth and/or regression without contributing any dose to the animal. The authors would like to acknowledge the financial and engineering support from Tessonics.

60 APPLIED LIFE SCIENCES↗

Biogeochemical Controls on the Potential for Long-Term Contaminant Leaching from Soils Developing on Historic Coal Mine Spoil

Coal mine spoil is widespread in US coal mining regions, and the potential long-term leaching of toxic metal(loid)s is a significant and underappreciated issue. This study aimed to determine the flux of contaminants from historic mine coal spoil at a field site located in Appalachian Ohio (USA) and link pore water composition and solid-phase composition to the weathering reaction stages within the soils. The overall mineralogical and microbial community composition indicates that despite very different soil formation pathways, soils developing on historic coal mine spoil and an undisturbed soil are currently dominated by similar mineral weathering reactions. Both soils contained pyrite coated with clays and secondary oxide minerals. However, mine spoil soil contained abundant residual coal, with abundant Fe- and Mn- (oxy)hydroxides. These secondary phases likely control and mitigate trace metal (Cu, Ni, and Zn) transport from the soils. While Mn was highly mobile in Mn-enriched soils, Fe and Al mobility may be more controlled by dissolved organic carbon dynamics than mineral abundance. There is also likely an underappreciated risk of Mn transport from coal mine spoil, and that mine spoil soils could become a major source of metals if local biogeochemical conditions change.

58 GEOSCIENCES↗

On single-degree-of-freedom flutter induced by activated controls

It is shown that activation of the trailing-edge control of an airfoil leads to single-degree-of-freedom type instabilities which span over a very wide region of reduced frequencies k, including high values of k (unlike the nonactivated system). These instabilities are shown to be sensitive to changes in pitching axis location, control deflection phase angle, and values of the reduced frequency. These sensitivities of the single-degree-of-freedom system cause the activated airfoil to be potentially sensitive to changes in flight conditions, and may be the source of the many difficulties encountered in suppressing classical multi-degree-of-freedom flutter by means of active controls. The results presented herein relate to zero Mach number and to a 20% trailing-edge control surface.

Nissim, E.↗

Design, Development, and Use of a Lunar Lander Simulation for NASA's Artemis Program

This paper describes the design, development, and initial use of a generalized and configurable lunar lander simulation to support NASA’s Artemis Program. This simulation is being developed for the Crew Compartment Office (CrewCo) in the Human Landing Systems (HLS) program and is called the HLS CrewCo Lander Simulation (HCLS). The HCLS provides insight into the challenges associated with returning humans to the Moon and the particular difficulties of operating at the Lunar South Pole. The simulation models a generalized integrated lunar landing spacecraft based on a government reference design but can and has been adapted to model vendor specific designs as well. The simulation architecture and tool sets provide a flexible framework that allows for quickly prototyping and evaluating various aspects of a piloted lunar landing system. This includes the modeling of all principal human controlled flight phases: rendezvous and docking with crew transfer systems; docked orbital outpost operations; undocking and lunar transfer; lunar orbital operations; lunar deorbit, descent, and landing (DDL); lunar surface operations; lunar ascent; and return to the orbital outpost. The flexibility of the simulation allows for the integrated evaluation of potential vehicle subsystems, crew displays, guidance and control modes, and trajectory designs. The purpose of the HCLS is not to design the ideal lunar lander, but rather to understand and the strengths and weaknesses of vehicle design choices. This paper describes the basic simulation architecture and discusses the tool sets used to develop the HCLS. This includes a number of open source tool sets and publicly available data sets. This paper also describes some of the early use cases and findings. The primary focus of early HCLS use has been on the manual piloting task to safely get the crew to the desired landing site in case of a failure in the automated guidance system. Several guidance modes and cues have been implemented which allow a pilot to manually fly the vehicle to the targeted landing site starting anywhere from powered descent initiation. It has been a valuable tool for understanding what is required to manually fly a lunar lander as well as giving a sense of the vehicle dynamics, which are much different than anything that is flown on Earth. A number of experienced test pilots have participated in manual piloting evaluations using the HCLS and provided valuable feedback on the piloting task which has been very beneficial to NASA and the HLS program.

James Michael Gentile↗

Design, Development, and Use of a Lunar Lander Simulation for NASA's Artemis Program

This paper describes the design, development, and initial use of a generalized and configurable lunar lander simulation to support NASA’s Artemis Program. This simulation is being developed for the Crew Compartment Office (CrewCo) in the Human Landing Systems (HLS) program and is called the HLS CrewCo Lander Simulation (HCLS). The HCLS provides insight into the challenges associated with returning humans to the Moon and the particular difficulties of operating at the Lunar South Pole. A generalized lunar landing spacecraft based on a government reference design has been modeled but the simulation can be modified and adapted to model vendor designs as well. The simulation architecture and toolsets provide a flexible framework that allows for quickly prototyping and evaluating various aspects of a piloted lunar landing system. This includes the modeling of all principal human controlled flight phases: rendezvous and docking with crew transfer systems; docked orbital outpost operations; undocking and lunar transfer; lunar orbital operations; lunar deorbit, descent, and landing (DDL); lunar surface operations; lunar ascent; and return to the orbital outpost. The flexibility of the simulation allows for the integrated evaluation of potential vehicle subsystems, crew displays, guidance and control modes, and trajectory designs. The purpose of the HCLS is not to design the ideal lunar lander, but rather to understand the strengths and weaknesses of vehicle design choices.

Edwin Z Crues↗