Search NASA⌕ Search

SEARCH · Search NASA

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Out-of-plane properties

This paper summarizes three areas of research which were performed to characterize out-of-plane properties of composite materials. In the first investigation, a series of tests was run to characterize the through-the-thickness tensile strength for a variety of composites that included 2D braids, 2D and 3D weaves, and prepreg tapes. A new test method based on a curved beam was evaluated. Failures were significantly different between the 2D materials and the 3D weaves. The 2D materials delaminated between layers due to out-of-plane tensile stresses while the 3D weaves failed due to the formation of radial cracks between the surface plies caused by high circumferential stresses along the inner radius. The strength of the 2D textile composites did not increase relative to the tapes. Final failure in the 3D weaves was caused by a circumferential crack similar to the 2D materials and occurred at a lower bending moment than in other materials. The early failures in the 3D weaves were caused by radial crack formation rather than a low through-the-thickness strength. The second investigation focused on the development of a standard impact test method to measure impact damage resistance. The only impact tests that currently exist are compression after impact (CAI) tests which incorporate elements of both damage resistance and damage tolerance. A new impact test method is under development which uses a quasi-static indentation (QSI) test to directly measure damage resistance. Damage resistance is quantified in terms of the contact force to produce a unit of damage where a metric for damage may be area in C-scan, depth of residual dent , penetration, damage growth, etc. A final draft of an impact standard that uses a QSI test method will be presented to the ASTM Impact Task Group on impact. In the third investigation, the impact damage resistance behavior of a variety of textile materials was studied using the QSI test method. In this study, the force where large damage initiates was measured and the delamination size as a function of force was determined. The force to initiate large damage was significantly lower in braids and weaves. The delamination diameter - impact forace relationship was quanitfied using a damage resistance parameter, Q(*), which related delamination diameter to imapct force over a range of delamination sizes. Using this Q(*) parameter to rate the materials, the stitched uniweaves, toughened epoxy tapes, and through-the-thickness orthogonal interlock weave were the most damage resistant.

Jackson, Wade C.↗

Study on Fracture of Fiber-Reinforced Polymeric Composites Using Spiral Notch Torsion Test

Fiber-reinforced polymer-matrix composites have been widely applied in various areas due to their excellent mechanical properties. In this study, carbon fiber-reinforced polymer-matrix composites and glass fiber-reinforced polymer-matrix composites failure tests under quasi static torsion have been demonstrated by using spiral notch torsion test methodology. Three types of cylindrical specimens with different fiber orientations were prepared and tested. For both composites, after increase stage, A type exhibited limited stress variations before the sudden failure, whereas B type showed gradual failure with torque drops. Displacement contours, stress contours and energy release rates were acquired using the anisotropic elastic finite element models. Microscopic characterization exhibited that the failure of A type occurred along interfaces between fibers and matrices, whereas circular cracks in B type propagated alternatively between polymeric matrices and interfaces. Type C failure is similar to type A whereas with a curvature observed on the fracture surface.

Du, Fen↗

Method for measuring static Young's modulus of tungsten to 1900 K

An instrument system was developed and tested to measure static Young's modulus of elasticity of refractory metals in tension at temperatures to 1900 K. The extensometer uses capacitance displacement sensors for measuring total elongation of a specimen and incorporates a unique high-resolution remote zero-adjusting mechanism. Details of a method for calibrating capacitance displacement sensors at temperatures to 800 K are included. The system was built to adapt to a vacuum furnace on a tensile machine and was tested on unalloyed tungsten rod specimens. The test results show that the system can measure the modulus of tungsten to 1900 K to within a precision of + or - 5 percent. The uncertainty of the measurement is estimated to be of the same order as the precision.

Harrigill, W. T., Jr.↗

Large Deformation Dynamic Bending of Composite Beams

Studies were conducted on the large deformation response of composite beams subjected to a dynamic axial load. The beams were loaded with a moderate eccentricity to promote bending. The study was primarily experimental but some finite element results were obtained. Both the deformation and the failure of the beams were of interest. The static response of the beams was also studied to determine potential differences between the static and dynamic failure. Twelve different laminate types were tested. The beams were loaded dynamically with a gravity driven impactor traveling at 19.6 ft/sec and quasi-static tests were conducted on identical beams in a displacement controlled manner. For laminates of practical interest, the failure modes under static and dynamic loadings were identical. Failure in most of the laminate types occurred in a single event involving 40% to 50% of the plies. However, failure in laminates with 30 deg or 15 deg off-axis plies occured in several events. All laminates exhibited bimodular elastic properties. Using empirically determined flexural properties, a finite element analysis was reasonably accurate in predicting the static and dynamic deformation response.

Derian, E. J.↗

Correlation between strength properties in standard test specimens and molded phenolic parts

This report describes an investigation of the tensile, flexural, and impact properties of 10 selected types of phenolic molding materials. The materials were studied to see in what ways and to what extent their properties satisfy some assumptions on which the theory of strength of materials is based: namely, (a) isotropy, (b) linear stress-strain relationship for small strains, and (c) homogeneity. The effect of changing the dimensions of tensile and flexural specimens and the span-depth ratio in flexural tests were studied. The strengths of molded boxes and flexural specimens cut from the boxes were compared with results of tests on standard test specimens molded from the respective materials. The nonuniformity of a material, which is indicated by the coefficient of variation, affects the results of tests made with specimens of different sizes and tests with different methods of loading. The strength values were found to depend on the relationship between size and shape of the molded specimen and size and shape of the fillers. The most significant variations observed within a diversified group of materials were found to depend on the orientation of fibrous fillers. Of secondary importance was the dependence of the variability of test results on the pieces of filler incorporated into the molding powder as well as on the size of the piece. Static breaking strength tests on boxes molded from six representative phenolic materials correlated well with falling-ball impact tests on specimens cut from molded flat sheets. Good correlation was obtained with Izod impact tests on standard test specimens prepared from the molding materials. The static breaking strengths of the boxes do not correlate with the results of tensile or flexural tests on standard specimens.

MATERIALS, MONSANTO RESINOX↗

Fatigue properties of shuttle thermal protection system

Static and cyclic load tests were conducted to determine the static and fatigue strength of the RIS tile/SIP thermal protection system used on the orbiter of the space shuttle. The material systems investigated include the densified and undensified LI-900 tile system on the .40 cm thick SIP and the densified and undensified LI-2200 tile system on the .23 cm (.090 inch) thick SIP. The tests were conducted at room temperature with a fully reversed uniform cyclic loading at 1 Hertz. Cyclic loading causes a relatively large reduction in the stress level that each of the SIP/tile systems can withstand for a small number of cycles. For example, the average static strength of the .40 cm thick SIP/LI-900 tile system is reduced from 86 kPa to 62 kPa for a thousand cycles. Although the .23 cm thick SIP/LI-2200 tile system has a higher static strength, similar reductions in the fatigue strength are noted. Densifying the faying surface of the RSI tile changes the failure mode from the SIP/tile interface to the parent RSI or the SIP and thus greatly increases the static strength of the system. Fatigue failure for the densified tile system, however, occurs due to complete separation or excessive elongation of the SIP and the fatigue strength is only slightly greater than that for the undensified tile system.

Sawyer, J. W.↗

Blade Testing Equipment Development and Commercialization: Cooperative Research and Development (Final Report)

Blade testing is required to meet wind turbine design standards, reduce machine cost, and reduce the technical and financial risk of deploying mass-produced wind turbine models. NREL's National Wind Technology Center (NWTC) in Colorado is the only blade test facility in the U.S. capable of performing full-scale static and fatigue testing of multi-megawatt-scale wind turbine blades. Rapid growth in wind turbine size over the past two decades has outstripped the size capacity of the NWTC blade test facility leaving the U.S. wind industry without a suitable means of testing blades for large land-based and offshore turbines. This CRADA will develop and commercialize testing technologies and test equipment, including scaling up, value engineering, and testing of equipment to be used at blade testing facilities in the U.S. and around the world.

17 WIND ENERGY↗

Status Report on Development of TREAT Water Loop

The Transient Reactor Test (TREAT) facility is a graphite based transient test reactor at the Idaho National Laboratory (INL). TREAT started operation in 1959 and performed thousands of transient irradiations for the primary purpose of nuclear fuel safety research. TREAT operations were suspended in 1994, and then, several years later, resumed reactor operations in 2017 to support development of advanced nuclear fuels. TREAT’s more recent historic focus had been for transients with relevance to sodium cooled fast spectrum reactors. TREAT’s first year of modern experiment work performed in 2018, however, saw the demonstration of new kinds of transients focused on light water reactor (LWR) needs including reactivity initiated accidents (RIA) and loss of coolant accidents (LOCA). The successful outcome of these efforts confirmed TREAT’s viability as a transient neutron source for LWR safety research. Since TREAT’s core is air cooled and provides no “built-in” thermal hydraulic boundary conditions for tests specimens, efforts have been underway to establish water-environment capabilities for testing specimens. Small static water capsules have been established to support single rod RIA testing where transient heating is brief. Similarly, deployment of enhanced water capsules with blowdown capability is nearing completion to support single rod LOCA testing. With careful experiment design these capsules can provide representative temperature response histories and water phase transitions for some experiment parameters. The capsule approach is appropriate for cost-effective early phase phenomena identification studies on novel fuels, or when the important test variables are thought to be fairly well understood so that they can be precisely targeted (such as they are for current fleet fuels with moderate burnup UO2 in uncoated zirconium alloy cladding). Due to lack of forced convection, however, the capsule approach cannot achieve representative temperature histories in all regions of the test fuel simultaneously (e.g. cladding and fuel centerline temperatures) while providing representative timing in water phase transitions. Nor can the capsule approach provide appropriate hydraulic conditions for multi-rod bundle testing. For these reasons, design and development has been undertaken for the TREAT Water-Environment Recirculating Loop (TWERL).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In-flight deflection measurement of the HiMAT aeroelastically tailored wing

An electro-optical flight deflection measurement system was developed for NASA for use on the highly maneuverable aircraft technology (HiMAT) remotely piloted research vehicle (RPRV) to provide a means of evaluating the performance of the HiMAT's aeroelastically tailored composite wing and canard. A description of the flight deflection measurement system is presented from a user's viewpoint and includes the general method of operation, system capabilities and limitations, method of installation on the HiMAT vehicle, and calibration of targets. Also included is a general description of the HiMAT RPRV and its design goals. Preliminary flight deflection and bending moment data were obtained at Mach 0.8 and were extrapolated to the Mach 0.9 maneuver design condition for comparison to NASTRAN predictions and ground loads test results. The preliminary flight test results tended to agree with the results obtained from the static ground loads tests, that is, that the NASTRAN model overpredicted the streamwise twist of the composite outer wing panel.

Deangelis, V. M.↗

Wind-tunnel investigation of spoiler, deflector, and slot lateral-control devices on wings with full-span split and slotted flaps

Report presents the results of an extensive investigation made in the NACA 7 by 10-foot wind tunnel of spoiler, deflector, and slot types of lateral-control device on wings with full-span split and slotted flaps. The static rolling and yawing moments were determined for all the devices tested, and the static hinge moments and the time response were determined for a few devices of each type.

Wenzinger, Carl J↗

The Development of an 8-inch by 8-inch Slotted Tunnel for Mach Numbers up to 1.28

An 8-inch by 8-inch transonic tunnel model with test section slotted on two opposite walls was constructed in which particular emphasis -was given to the development of slot geometry, slot-flow reentry section, and short-diffuser configurations for good test-region flow and minimum total-pressure losses. Center-line static pressures through the test section, wall static pressures through the other parts of the tunnel, and total-pressure distributions at the inlet and exit stations of the diffuser were measured- With a slot length equal to two tunnel heights and 1/14 open-area-ratio slotted walls) a test region one tunnel height in length was obtained in which the deviation from the mean Mach number was less than +/- 0.01 up to Mach number 1.15. With 1/7 open-area-ratio slotted walls, a test region 0.84 tunnel heights in length with deviation less than +/- O.01 was obtained up to Mach number 1.26. Increasing the tunnel diffuser angle from 6.4 to 10 deg. increased pressure loss through the tunnel at Mach number 1.20 from 15 percent to 20 percent of the total pressure. The use of other diffusers with equivalent angles of 10 deg. but contoured so that the initial diffusion angle was less than 10 deg. and the final angle was 200 reduced the losses to as low as 16 percent. A method for changing the test-section Mach number rapidly by controlling the flow through a bypass line from the tunnel settling chamber to the slot-flow plenum chamber of the test section was very effective. The test-section Mach number was reduced approximately 5 percent in 1/8 second by bleeding into the test section a flow of air equal to 2 percent of the mainstream flow and 30 percent in 1/4 second with bleed flow equal to 10 percent of the mainstream flow. The rate of reduction was largely determined by the opening rate of the bleed-flow-control valve.

Little, B. H., Jr.↗

Subsonic static and dynamic stability characteristics of the test technique demonstrator NASP configuration

The paper describes the procedure used for and the results obtained of wind-tunnel tests of the National Aerospace Plane (NASP) configuration, which were conducted in the NASA Langley Research Center High Speed Tunnel using a blended body NASP configuration designed by the research center. Static and dynamic stability characteristics were measured at Mach numbers 0.3, 0.6, and 0.8. In addition to tests of the baseline configuration, component buildup tests with a canard surface and with a body flap were carried out. Results demonstrated a positive static stability of the baseline configuration, except at the higher angles of attack at Mach 0.8. A good agreement was found between the inphase dynamic parameters and the corresponding static data.

Boyden, Richmond P.↗

Acoustic tests of duct-burning turbofan jet noise simulation

The results of a static acoustic and aerodynamic performance, model-scale test program on coannular unsuppressed and multielement fan suppressed nozzle configurations are summarized. The results of the static acoustic tests show a very beneficial interaction effect. When the measured noise levels were compared with the predicted noise levels of two independent but equivalent conical nozzle flow streams, noise reductions for the unsuppressed coannular nozzles were of the order of 10 PNdB; high levels of suppression (8 PNdB) were still maintained even when only a small amount of core stream flow was used. The multielement fan suppressed coannular nozzle tests showed 15 PNdB noise reductions and up to 18 PNdB noise reductions when a treated ejector was added. The static aerodynamic performance tests showed that the unsuppressed coannular plug nozzles obtained gross thrust coefficients of 0.972, with 1.2 to 1.7 percent lower levels for the multielement fan-suppressed coannular flow nozzles. For the first time anywhere, laser velocimeter velocity profile measurements were made on these types of nozzle configurations and with supersonic heated flow conditions. Measurements showed that a very rapid decay in the mean velocity occurs for the nozzle tested.

Knott, P. R.↗

Mode Jumping of an Isogrid Panel Under Quasi-Static Compression

A wide column test of a composite isogrid panel subjected to quasi-static, axial compression is modeled with a hybrid-static dynamic computational method. The data from the test panel exhibited discontinuous responses in the compressive load for slowly increased end-shortening. The computational model was developed to corroborate these discontinuities with the phenomenon of mode jumping. Mode jumping refers to the transient response of the panel from an unstable bifurcation point on a postbuckled equilibrium path to a second stable equilibrium state on a new equilibrium path. On the new equilibrium path, both the analysis and test show that the panel can resist increased endshortening beyond that of the unstable critical point. Fair agreement is achieved between the analysis and test.

Muheim, Danniella M.↗

Failure Strain and Related Triaxiality of Aluminum 6061-T6, A36 Carbon Steel, 304 Stainless Steel, and Nitronic 60 Metals, Part I: Experimental Investigation

The objective of this study is to develop failure-limit material models for Aluminum 6061-T6, A36 Carbon Steel, 304 Stainless Steel, and Nitronic 60 metals, based on parameters of plastic equivalent strain (failure strain) and stress triaxiality. The research is conducted in two parts. This paper presents Part One of the study. In Part One, custom-designed test specimens undergo controlled uniaxial tension and compression testing at ambient temperature. These tests are performed at quasi-static speeds using Universal Testing Machines (UTMs) in accordance with ASTM E8 and ASTM E9 standards. Experimental data, specifically engineering stress–strain and force–displacement curves, are recorded from the onset of loading until specimen fracture, or in the case of compression tests, until the capacity of the testing machine is reached. In Part Two, the emphasis shifts to the calibration of Finite Element Analysis (FEA) models of the custom-designed test specimens. Plastic equivalent strain and the corresponding stress triaxiality values at failure are extracted from each test specimen for the given metal. These values are then systematically plotted onto a single graph to construct the failure-limit curve, which delineates the boundary conditions for material failure. This approach will facilitate the development of a comprehensive material property definition that correlates plastic equivalent strain with stress triaxiality at failure for Aluminum 6061-T6, A36 Carbon Steel, 304 Stainless Steel, and Nitronic 60 metals.

Harwell, Ron↗

Enabling the Electrification of Offshore Activities – Co-Demonstration of Next-Generation Autonomous Offshore Power System and Resident, Uncrewed Mobile and Static Assets at PacWave Wave Energy Test Site

Oceans cover two-thirds of the earth's surface and form the world's biggest and best – yet largely untapped – battery. Ocean waves have more energy density than other renewables, including wind, solar, and biomass, and have the potential to supply 4x the world's annual energy consumption (Masterson, 2022; Zic, 2020). In addition to the impact wave energy can have on decarbonizing and diversifying the electric grid, it offers a significant value proposition in the emerging blue economy sector (LiVecchi et al, 2019). The blue economy consists of industries operating offshore, including shipping, oil and gas, defense and security, aquaculture, and research. These industries require bringing people and energy on site to perform daily work, but current energy costs in the blue economy are extremely high. Here, the prevailing processes are complex, including shore dependencies and fuel transportation logistics. Few alternatives for reliable power generation exist, with the most prominent being high cost and high carbon emissions diesel generation. Because of this lack of affordable, reliable power, the trends of electrification, digitization, and automation that have led to substantial innovation and improvements in the terrestrial economy over the last two decades are slow to come to the blue economy.

16 TIDAL AND WAVE POWER↗