Search NASA⌕ Search

SEARCH · Search NASA

Results for “structural modulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Thermal control system for a spacecraft modular housing

The development of a thermal control system for a spacecraft module is discussed. The wall structures are composed of superinsulation in some cases and of thermally conductive material in other cases. Heat pipes are installed to provide a path of heat transfer from the interior of the module to space. The design of the system makes it possible to maintain a relatively uniform temperature throughout the module with side variations of the amount of heat dissipated by the components within the module.

Eby, R. J.↗

On the radio variability of V410 Tauri

The radio flux density of the star V410 Tauri has been monitored at 6 and 2 cm wavelengths at monthly intervals over a one-year period with the VLA. In contrast to earlier observations, the radio emission was typically at the level of roughly 1 mJy with flat or negative spectral indices. No large radio 'flare' events were detected. However, a periodicity analysis of the quiescent data shows statistically significant evidence for a modulation of the radio emission, with a period of 0.933 days, or one-half the optical period reported by Vrba, et al. (1988). If the modulation is real, it would imply that (1) the radio emission is produced either in localized zones on two opposite hemispheres of the star, or in a single, presumably high-latitude, structure that remains visible for an entire rotation period; (2) this zone or zones must be comparable to the stellar radius in size; (3) the energy spectrum of the radiating electrons is stable over long times (greater than 1 yr) but the absolute intensity level in the quiescent state may vary by factors of a few; and (4) the emission solid angle varies with viewing angle of the emission zone. It is suggested that gyrosynchrotron radiation from closed-loop magnetic structures may be responsible for the quasisteady low-level radio emission reported here. A geometric model for the radio emission structure may explain qualitatively the modulation of the radio emission. By analogy with the premain-sequence star DoAr 21, this same physical mechanism may produce both the 'quiescent' and 'flaring' radio emission. The monitoring results suggest that strong radio outbursts, such as were previously observed for V410 Tau, are relatively rare.

Bieging, John H.↗

A Proof-Of-Principle Echo-Enabled Harmonic Generation Experiment at SLAC

In this paper we describe the technical design of an ongoing proof-of-principle echo-enabled harmonic generation (EEHG) experiment at the Next Linear Collider Test Accelerator (NLCTA) at SLAC.We present the design considerations and the technical details of the experiment. Recently a new method, entitled echo-enabled harmonic generation, was proposed for generation of high harmonics using the beam echo effect. In an EEHG free electron laser (FEL), an electron beam is energy modulated in a modulator and then sent through a dispersive section with a high dispersion strength. After this first stage, the modulation obtained in the modulator is macroscopically washed out, while simultaneously introducing complicated fine structure (separated energy bands) into the phase space of the beam. A second laser is used to further modulate the beam energy in a second modulator. After passing through a second dispersive section, the separated energy bands will be converted into current modulation and the echo signal then occurs as a recoherence effect caused by the mixing of the correlations between the modulation in the second modulator and the fine structures in the beam. The EEHG scheme has a remarkable up-frequency conversion efficiency; it has been shown that the EEHG FEL scheme may allow generation of soft x-rays directly from a UV seed laser in a single stage. In order to confirm the physics behind the EEHG technique and benchmark the theory, a proof-of-principleEEHG experimentwas planned at SLAC. The experiment is now in a commissioning stage and the preliminary results are reported in a separate paper of these proceedings. In this paper we present the design considerations and the details of the experiment setup.

43 PARTICLE ACCELERATORS↗

Noise produced by turbulent flow into a rotor: Users manual for noise calculation

A users manual for a computer program for the calculation of noise produced by turbulent flow into a helicopter rotor is presented. These inputs to the program are obtained from the atmospheric turbulence model and mean flow distortion calculation, described in another volume of this set of reports. Descriptions of the various program modules and subroutines, their function, programming structure, and the required input and output variables are included. This routine is incorporated as one module of NASA's ROTONET helicopter noise prediction program.

Amiet, R. K.↗

Rack assembly for mounting solar modules

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Plaisted, Joshua Reed↗

Rack assembly for mounting solar modules

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures to be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

14 SOLAR ENERGY↗

Rack assembly for mounting solar modules

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

14 SOLAR ENERGY↗

Time-Dependent Behavior of High-Strength Kevlar and Vectran Webbing

High-strength Kevlar and Vectran webbings are currently being used by both NASA and industry as the primary load-bearing structure in inflatable space habitation modules. The time-dependent behavior of high-strength webbing architectures is a vital area of research that is providing critical material data to guide a more robust design process for this class of structures. This paper details the results of a series of time-dependent tests on 1-inch wide webbing including an initial set of comparative tests between specimens that underwent realtime and accelerated creep at 65 and 70% of their ultimate tensile strength. Variability in the ultimate tensile strength of the webbings is investigated and compared with variability in the creep life response. Additional testing studied the effects of load and displacement rate, specimen length and the time-dependent effects of preconditioning the webbings. The creep test facilities, instrumentation and test procedures are also detailed. The accelerated creep tests display consistently longer times to failure than their real-time counterparts; however, several factors were identified that may contribute to the observed disparity. Test setup and instrumentation, grip type, loading scheme, thermal environment and accelerated test postprocessing along with material variability are among these factors. Their effects are discussed and future work is detailed for the exploration and elimination of some of these factors in order to achieve a higher fidelity comparison.

Jones, Thomas C.↗

Clinical Study of the Necessity of Replanning Before the 25th Fraction During the Course of Intensity-Modulated Radiotherapy for Patients With Nasopharyngeal Carcinoma

Purpose: To quantify the target and normal structures on dose distributing variations during intensity-modulated radiotherapy (IMRT) and to assess the value of replanning for nasopharyngeal carcinoma (NPC) patients. Methods and Materials: Twenty-eight NPC patients treated with IMRT were recruited. The IMRT was delivered in 33 fractions, to 70 to 76Gy, to the gross tumor volume (GTV). Before the 25th fraction of IMRT, a new simulation computed tomography (CT) scan was acquired for all patients. According to the dose constraint criterion in the Radiation Therapy Oncology Group (RTOG) 0225 protocol, the replanning was generated on the new simulation CT. With the Quality Assessment Center of a CORVUS 6.3 treatment planning system, a phantom plan was generated for each patient by applying the beam configurations of the initial plan to the anatomy of the new simulation CT. The dose-volume histograms of the phantom plan were compared with the replanning. Results: The percentage of prescription dose delivered to the clinical target volume (CTV1) was significantly increased by 4.91% +- 10.89%, whereas the maximum dose to the spinal cord, mean dose to the left parotid, and V30 to the right parotid were significantly decreased by 5.00 +- 9.23Gy, 4.23 +- 10.03Gy, and 11.47% +- 18.89% respectively in the replanning, compared with the phantom plan (p < 0.05). Based on the dose constraint criterion in the RTOG0225 protocol, 50% of phantom plans (14/28) were out of limit for the dose to the normal critical structures, whereas no plan was out of limit in replanning (p < 0.001). Conclusion: Replanning for patients with NPC before the 25th fraction during IMRT helps to ensure adequate dose to the target volumes and safe doses to critical normal structures.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Structural Element Testing in Support of the Design of the NASA Composite Crew Module

In January 2007, the NASA Administrator and Associate Administrator for the Exploration Systems Mission Directorate chartered the NASA Engineering and Safety Center (NESC) to design, build, and test a full-scale Composite Crew Module (CCM). For the design and manufacturing of the CCM, the team adopted the building block approach where design and manufacturing risks were mitigated through manufacturing trials and structural testing at various levels of complexity. Following NASA's Structural Design Verification Requirements, a further objective was the verification of design analysis methods and the provision of design data for critical structural features. Test articles increasing in complexity from basic material characterization coupons through structural feature elements and large structural components, to full-scale structures were evaluated. This paper discusses only four elements tests three of which include joints and one that includes a tapering honeycomb core detail. For each test series included are specimen details, instrumentation, test results, a brief analysis description, test analysis correlation and conclusions.

Kellas, Sotiris↗

Fault-tolerant software for aircraft control systems

Concepts for software to implement real time aircraft control systems on a centralized digital computer were discussed. A fault tolerant software structure employing functionally redundant routines with concurrent error detection was proposed for critical control functions involving safety of flight and landing. A degraded recovery block concept was devised to allow collocation of critical and noncritical software modules within the same control structure. The additional computer resources required to implement the proposed software structure for a representative set of aircraft control functions were discussed. It was estimated that approximately 30 percent more memory space is required to implement the total set of control functions. A reliability model for the fault tolerant software was described and parametric estimates of failure rate were made.

Source record↗

In operando observation system for electrochemical reaction by soft X-ray absorption spectroscopy with potential modulation method

In order to investigate local structures of electrolytes in electrochemical reactions under the same scan rate as a typical value 100 mV/s in cyclic voltammetry (CV), we have developed an in operando observation system for electrochemical reactions by soft X-ray absorption spectroscopy (XAS) with a potential modulation method. XAS spectra of electrolytes are measured by using a transmission-type liquid flow cell with built-in electrodes. The electrode potential is swept with a scan rate of 100 mV/s at a fixed photon energy, and soft X-ray absorption coefficients at different potentials are measured at the same time. By repeating the potential modulation at each fixed photon energy, it is possible to measure XAS of electrochemical reaction at the same scan rate as in CV. We have demonstrated successful measurement of the Fe L-edge XAS spectra of aqueous iron sulfate solutions and of the change in valence of Fe ions at different potentials in the Fe redox reaction. The mechanism of these Fe redox processes is discussed by correlating the XAS results with those at different scan rates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure–Function Analysis of the Extended Conformation of a Polyketide Synthase Module

Catalytic modules of assembly-line polyketide synthases (PKSs) have previously been observed in two very different conformations—an “extended” architecture and an “arch-shaped” architecture—although the catalytic relevance of neither has been directly established. By the use of a fully human naïve antigen-binding fragment (F ab ) library, a high-affinity antibody was identified that bound to the extended conformation of a PKS module, as verified by X-ray crystallography and tandem size-exclusion chromatography–small-angle X-ray scattering (SEC–SAXS). Kinetic analysis proved that this antibody-stabilized module conformation was fully competent for catalysis of intermodular polyketide chain translocation as well as intramodular polyketide chain elongation and functional group modification of a growing polyketide chain. Furthermore, the extended conformation of a PKS module is fully competent for all of its essential catalytic functions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Apparatus and method for intra-layer modulation of the material deposition and assist beam and the multilayer structure produced therefrom

A method of producing a multilayer structure that has reduced interfacial roughness and interlayer mixing by using a physical-vapor deposition apparatus. In general the method includes forming a bottom layer having a first material wherein a first plurality of monolayers of the first material is deposited on an underlayer using a low incident adatom energy. Next, a second plurality of monolayers of the first material is deposited on top of the first plurality of monolayers of the first material using a high incident adatom energy. Thereafter, the method further includes forming a second layer having a second material wherein a first plurality of monolayers of the second material is deposited on the second plurality of monolayers of the first material using a low incident adatom energy. Next, a second plurality of monolayers of the second material is deposited on the first plurality of monolayers of the second material using a high incident adatom energy.

Wadley, Hadyn N. G.↗

SOLL-E: A Module Transport and Placement Robot for Autonomous Assembly of Discrete Lattice Structures

This paper presents the design and development of a transport and placement robot that demonstrates autonomous assembly of structural building blocks. The robots are intended to serve as a critical component of automated structural assembly and maintenance systems. The Scaling Omni-directional Lattice Locomoting Explorer (SOLL-E) uses a 5-DoF bipedal inchworm locomotion architecture with locking foot and cargo grippers. The locomotion system employs large magnet gap diameter BLDC motors with moderate timing belt gearing for primary joints, and DC planetary gearmotors for turning. Foot and cargo grippers are identical, with servo-actuated locking mechanisms. Three modular controller boards are used to control these actuators in real-time, with command and telemetry data transferred between the server and each controller board via WiFi. Functionality and performance were evaluated in a ground demonstration.

robotics↗

Integrated launch and emergency vehicle system

A heavy launch vehicle is discussed. The launch vehicle is comprised of an expendable, multi-container, propellant tank that has a plurality of winged booster propulsion modules at one end and a payload supported by adapter structure at the other end. The preferred payload is an entry module that can be adapted for docking to the space station and used as a return vehicle for the space station crew. Additionally, the payload may include communication satellites, supplies, equipment, and/or structural elements for the space station. The winged propulsion modules are released from the expendable propellant tank, in pairs, and they return to Earth in a controlled glide. After a safe landing, at or near the launch site, the modules are prepared for reuse. The rocket engines for each propulsion module are dual-fuel, dual-mode engines and use methane-oxygen and hydrogen-oxygen from the multi-containers of the propellant tank. When the propulsion modules are released from the expendable propellant tank, the rocket engines are moved into the module cargo bay for the return glide flight.

Martin, James A.↗