Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface steps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Three Year Aging of Prototype Flight Laser at 10 Khz and 1 Ns Pulses with External Frequency Doubler for the Icesat-2 Mission

We present the results of three year life-aging of a specially designed prototype flight source laser operating at 1064 nm, 10 kHz, 1ns, 15W average power and external frequency doubler. The Fibertek-designed, slightly pressurized air, enclosed-container source laser operated at 1064 nm in active Q-switching mode. The external frequency doubler was set in a clean room at a normal air pressure. The goal of the experiment was to measure degradation modes at 1064 and 532 nm discreetly. The external frequency doubler consisted of a Lithium triborate, LiB3O5, crystal operated at non-critical phase-matching. Due to 1064 nm diagnostic needs, the amount of fundamental frequency power available for doubling was 13.7W. The power generated at 532 nm was between 8.5W and 10W, depending on the level of stress and degradation. The life-aging consisted of double stress-step operation for doubler crystal, at 0.35 J/cm2 for almost 1 year, corresponding to normal conditions, and then at 0.93 J/cm2 for the rest of the experiment, corresponding to accelerated testing. We observed no degradation at the first step and linear degradation at the second step. The linear degradation at the second stress-step was related to doubler crystal output surface changes and linked to laser-assisted contamination. We discuss degradation model and estimate the expected lifetime for the flight laser at 532 nm. This work was done within the laser testing for NASA's Ice, Cloud, and land Elevation Satellite-2 (ICESat-2) LIDAR at Goddard Space Flight Center in Greenbelt, MD with the goal of 1 trillion shots lifetime.

Frequency Doubling↗

Three Three-Year Aging of Prototype Flight Laser at 10 kHz and 1 ns Pulses With External Frequency Doubler for ICESat-2 Mission

We present the results of three year life-aging of a specially designed prototype flight source laser operating at 1064 nm, 10 kHz, 1ns, 15W average power and external frequency doubler. The Fibertek-designed, slightly pressurized air, enclosed-container source laser operated at 1064 nm in active Q-switching mode. The external frequency doubler was set in a clean room at a normal air pressure. The goal of the experiment was to measure degradation modes at 1064 and 532 nm discreetly. The external frequency doubler consisted of a Lithium triborate, LiB3O5, crystal operated at non-critical phase-matching. Due to 1064 nm diagnostic needs, the amount of fundamental frequency power available for doubling was 13.7W. The power generated at 532 nm was between 8.5W and 10W, depending on the level of stress and degradation. The life-aging consisted of double stress-step operation for doubler crystal, at 0.35 Jcm2 for almost 1 year, corresponding to normal conditions, and then at 0.93 Jcm2 for the rest of the experiment, corresponding to accelerated testing. We observed no degradation at the first step and linear degradation at the second step. The linear degradation at the second stress-step was related to doubler crystal output surface changes and linked to laser-assisted contamination. We discuss degradation model and estimate the expected lifetime for the flight laser at 532 nm. This work was done within the laser testing for NASAs Ice, Cloud, and land Elevation Satellite-2 (ICESat-2) LIDAR at Goddard Space Flight Center in Greenbelt, MD with the goal of 1 trillion shots lifetime.

Lidar↗

Synchronous Separation, Seaming, Sealing and Sterilization (S4) using Brazing for Sample Containerization and Planetary Protection

The return of samples back to Earth in future missions would require protection of our planet from the risk of bringing uncontrolled biological materials back with the samples. This protection would require “breaking the chain of contact (BTC)”, where any returned material reaching Earth for further analysis would have to be sealed inside a container with extremely high confidence. Therefore, the acquired samples would need to be contained while destroying any potential biological materials that may contaminate the external surface of the container. A novel process that could be used to contain returning samples has been developed and demonstrated in a quarter scale size. The process consists of brazing using non-contact induction heating that synchronously separates, seams, seals and sterilizes (S4) the container. The use of brazing involves melting at temperatures higher than 500°C and this level of heating assures sterilization of the exposed areas since all carbon bonds (namely, organic materials) are broken at this temperature. The mechanism consists of a double wall container with inner and outer shells having Earth-clean interior surfaces. The process consists of two-steps, Step-1: the double wall container halves are fabricated and brazed (equivalent to production on Earth); and Step-2 is the S4 process and it is the equivalent to the execution on-orbit around Mars. In a potential future mission, the double wall container would be split into two halves and prepared on Earth. The potential on-orbit execution would consist of inserting the orbiting sample (OS) container into one of the halves and then mated to the other half and brazed. The latest results of this effort will be described and discussed in this manuscript.

Salazar, Eduardo↗

ANALYSIS OF THE MSL/MEDLI ENTRY DATA WITH COUPLED CFD AND MATERIAL RESPONSE.

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heat-shield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material. PICA is a lightweight carbon fiber/polymeric resin material that offers out-standing performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP). The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on Open-FOAM (PATO) using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA, is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Mars Science Laboratory↗

Analysis of MSL/MEDLI Entry Data with Coupled CFD and Material Response

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heatshield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers outstanding performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP) [2]. The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on OpenFOAM (PATO) [4,5,6] using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA [7], is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Thermal Protection Systems↗

Volcanic Field Sites for Artemis Testing and Training

The Artemis Program will reestablish human presence on the Moon and lead to a new era of scientific discovery and exploration. Led by the National Aeronautics and Space Administration (NASA), the Artemis Program is a collaboration of space agencies and companies around the world. An integrated effort between various disciplines of science, engineering, and mission operations is currently developing methods, facilities, and analog field locations to train astronauts and test hardware and concepts of operations. These efforts aim to best prepare for the next steps of human exploration on the lunar surface and beyond. Numerous terrestrial volcanic field sites were evaluated and selected for their unique roles in helping to prepare for the lunar surface mission phases. This effort heavily leveraged the comprehensive academic research conducted at these field sites, as well as the tremendous Apollo heritage. The currently selected volcanic field sites include the San Francisco Volcanic Field in Northern Arizona, the Potrillo Volcanic Field in southern New Mexico, the highlands of Iceland, and the Southwestern Nevada Volcanic Field. Within each of these volcanic field sites numerous specific testing and training locations are being further developed utilizing the analogous terrain and unique features in these regions. Recent Artemis testing and training events have been conducted at a number of these volcanic field sites by both a dedicated Artemis Geology Training Team and a Joint Extra Vehicular Activity (EVA) Testing Team. This presentation will highlight the selected sites as well as the objectives and accomplishments of some of the recent field-testing events and training courses. Additionally, we continually strive to pursue additional sites, locations, data sets, collaborations, and partnerships in this endeavor and welcome knowledge transfer and community input.

Trevor Graff↗

Influences of Varied Electrical Discharge Machining Operations on Surface Conditions of Several Nickel-Based Superalloys

Nickel-based superalloys designed for use in gas turbine engines blades are difficult and expensive to properly machine without undue surface damage, due in part to their superior mechanical properties at high temperatures. Numerically controlled electrical discharge machining (EDM) has progressed to commonly be used as a machining process for initial sectioning, detailed roughing, and even some finishing operations. The objective of this study was to examine the effect of EDM on resulting surface conditions of superalloy 718 after slicing using typical rough, semi-finish, and finish condition sets with a typical wire EDM machine. Surface roughness, residual stress, and microstructures were compared for these conditions. The varied EDM conditions influenced surface roughness as intended. The residual stresses and surface roughness directly corresponding to the EDM steps were determined. While roughness decreased when progressing from rough to finish EDM conditions, tensile residual stresses unexpectedly increased. Brief assessments after EDM of two higher performance powder metallurgy disk superalloys ME209 and LSHR indicated this inverse relationship of roughness versus tensile residual stress was also present for these superalloys, where tensile residual stresses were significantly enhanced.

superalloys↗

Developing Flexible Instruments for Biological Missions Beyond Low Earth Orbit

As the future of spaceflight focuses on human exploration beyond low Earth orbit (BLEO), space biology experiments using model organisms are becoming increasingly important. NASA’s Artemis missions seek to build technologies that enable extended crewed flights into deep space, a region not travelled by humans for over 50 years. From the Apollo missions and ground experiments, it is known that BLEO galactic cosmic radiation can cause damage to DNA and proteins, as well as an increased risk of cancer to astronauts. NASA’s latest biosensor technology, the Lunar Explorer Instrument for space biology applications (LEIA), builds upon the viable and cost-effective platform of CubeSats to take biology experiments back to the Moon. Stationed on the lunar South Pole, LEIA will collect valuable in-situ radiation data, and use yeast to study the response to combined partial gravity and radiation stressors, as well as provide a proof-of-concept of on-demand bio nutrient production as a countermeasure for future crewed missions. Directly enhancing the abilities of the BioSentinel CubeSat mission, the main components of LEIA are the two radiation sensors and the 4U BioSensor, composed of 16-microfluidic cards housing dried yeast cells. The payload is fully contained and autonomous, directly sending data back to Earth without the need for sample return. In addition, the thermal environment of the BioSensor is optimized to keep cells alive for the pre-launch period and duration of the Artemis III mission, while also running on limited power supply. This talk highlights how the development of flexible instruments, like LEIA, enables human exploration into deep space. The technology developed with LEIA can be used as a stepping-stone for establishing a sustained lunar surface habitation and beyond, as humans continue to venture into space.

Payne Elizabeth Turney↗

High-Performance Flexible Perovskite Solar Cells by Using a Combination of Ultrasonic Spray-Coating and Low Thermal Budget Photonic Curing

Realizing the commercialization of high-performance and robust perovskite solar cells urgently requires the development of economically scalable processing techniques. Here we report a high-throughput ultrasonic spray-coating (USC) process capable of fabricating perovskite film-based solar cells on glass substrates with power conversion efficiency (PCE) as high as 13.04%. Perovskite films with high uniformity, crystallinity, and surface coverage are obtained in a single step. Moreover, we report USC processing on TiOx/ITO-coated polyethylene terephthalate (PET) substrates to realize flexible perovskite solar cells with PCE as high as 8.02% that are robust under mechanical stress. In this case, an optical curing technique was used to achieve a highly-conductive TiOx layer on flexible PET substrates for the first time. The high device performance and reliability obtained by this combination of USC processing with optical curing appears very promising for roll-to-roll manufacturing of high-efficiency, flexible perovskite solar cells.

Sanjib, Das↗

Enhanced spot preparation for liquid extractive sampling and analysis

A method for performing surface sampling of an analyte, includes the step of placing the analyte on a stage with a material in molar excess to the analyte, such that analyte-analyte interactions are prevented and the analyte can be solubilized for further analysis. The material can be a matrix material that is mixed with the analyte. The material can be provided on a sample support. The analyte can then be contacted with a solvent to extract the analyte for further processing, such as by electrospray mass spectrometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Temporal Analysis Of Product Computational Methods

The temporal analysis of products (TAP) reactor provides a wealth of data for transient studies of gas phase heterogeneous reactions, with the ability to provide a comprehensive picture of intrinsic reaction kinetics pertaining to complex catalytic mechanisms. A novel framework called the Y-Procedure was previously developed by Yablonsky and coworkers to extract information from this non-steady-state kinetic data. The Y-Procedure reconstructs the chemical transformation rate and gas composition in the catalytic zone with no a priori assumptions on the kinetic model and is used to relate changes in catalytic reaction rates and kinetic parameters to changes in a catalyst’s surface composition. This code provides the required steps to pre-process, analyze, and perform the Y-Procedure on experiments derived from the TAP reactor.

Kunz, Matthew R.↗

Upcycling Low Linear Density Polyethylene Waste into Turbostratic Graphene for High Mass Loading Supercapacitors

In this work, LLDPE was upcycled into a high quality turbostratic graphene using a pre-treatment step to oxidatively crosslink the polymer with the assistance of solid additives (KCl and K2CO3) that improve crosslinking by increasing the effective surface area of the polymer melt during processing. After this pretreatment step, the crosslinked polymer could then be carbonized and catalytically graphenized between 400-950 °C without complete decomposition of the material. The LLDPE derived graphene (LLDPE-G) obtained from this process has a Brunauer–Emmett–Teller (BET) specific surface area, up to 1800 m2g-1 and average Raman ID/IG and I2D/IG ratios of 0.85 and 0.57, respectively, indicating high quality graphene. When used as an electrode material in symmetric supercapacitors, LLDPE-G possesses an outstanding specific capacitance up to 175 Fg-1 at a mass loading of 20 mgcm-2, which is two times the commercial requirement, yielding an excellent areal capacitance of 3.5 Fcm-2. Moreover, LLDPE-G exhibits exceptional cycling stability with a capacitance retention of 95.8% after 100,000 cycles at a current density of 4.0 Ag-1. Additionally, the KCl and K2CO3 were recycled and reused over 3 complete cycles to make new LLDPE-G with the material quality and electrocapacitive performance retained and verified after each cycle. Our approach creates new opportunities for upcycling not only waste LLDPE but also other varieties of PE to high value graphene materials.

Gao, Yuan [NETL Site Support Contractor, National ↗

Scanning SQUID susceptometers with sub-micron spatial resolution

Superconducting QUantum Interference Device (SQUID) microscopy has excellent magnetic field sensitivity, but suffers from modest spatial resolution when compared with other scanning probes. This spatial resolution is determined by both the size of the field sensitive area and the spacing between this area and the sample surface. In this paper we describe scanning SQUID susceptometers that achieve sub-micron spatial resolution while retaining a white noise floor flux sensitivity of ≈2μΦ{sub 0}/Hz{sup 1/2}. This high spatial resolution is accomplished by deep sub-micron feature sizes, well shielded pickup loops fabricated using a planarized process, and a deep etch step that minimizes the spacing between the sample surface and the SQUID pickup loop. We describe the design, modeling, fabrication, and testing of these sensors. Although sub-micron spatial resolution has been achieved previously in scanning SQUID sensors, our sensors not only achieve high spatial resolution but also have integrated modulation coils for flux feedback, integrated field coils for susceptibility measurements, and batch processing. They are therefore a generally applicable tool for imaging sample magnetization, currents, and susceptibilities with higher spatial resolution than previous susceptometers.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Surfactants adsorption on crossing stripes and steps

Using coarse-grained dissipative particle dynamics (DPD) simulations, we systematically study the effect of surface heterogeneity on surfactant adsorption. Here we investigate the adsorption and aggregation of surfactants on hydrophobic stripes crossing each other perpendicularly (i.e., crossing stripes) and on hydrophobic steps. The results are compared with those obtained for isolated stripes. We find that on crossing stripes of moderate stripe widths (e.g., L = 0.61LS, 1.22LS and 1.83LS, where LS is the length of one surfactant molecule) the crossing region hinders the formation of defect-free adsorbed surfactant structures. By increasing the stripe width and/or by increasing the length of one of the two perpendicularly crossing stripes (i.e., lowering the surface density of defects/intersections), the crossing region is found to have a weaker effect on the features of the adsorbed structures. Regarding surfactant adsorption on steps, our simulation results show that the self-assembled aggregates can be stretched along the step corner, and the resultant elastic deformation can hinder adsorption. This qualitative observation can facilitate a description of surfactant adsorption that takes into consideration also the deformation of the self-assembled film. As suggested by such a general model, increasing the convex angle of the step, increasing the size of the surfactant head groups, and changing other physical parameters can reduce the elastic energy penalty, and yield larger amounts of surfactants adsorbed. The results presented could assist in understanding and sometimes predicting surfactant adsorption on heterogeneous surfaces, suggest methods to formulate surfactant mixtures to control surface coverage on heterogeneous surfaces, and perhaps facilitate new methods for the fabrication of nano-structured surfaces.

Chemistry↗

Fabrication of low blaze angle gratings by replication and plasma etch

We suggest a new method of making ultra-low blaze angle gratings for synchrotron application. The method is based on reduction of the blaze angle of a master grating by replication followed by a plasma etch. A master blazed grating with a relatively large blaze angle is fabricated by anisotropic wet etching of a Si single crystal substrate. The surface of the master grating is replicated by a polymer material on top of a quartz substrate by nanoimprinting and then transferred into quartz by a plasma etch. Then a 2nd nanoimprint step is applied to transfer the saw-tooth surface into a resist layer on top of a Si grating substrate. The plasma etch through the patterned resist layer provides transfer of the grooves into the Si substrate and results in reduction of the blaze angle due to the difference in etch rates of the resist and Si. We investigated the impact of the replication process on the groove shape, facet surface roughness, and diffraction efficiency of the fabricated 200 lines/mm low blaze angle grating.

Park, Sooyeon↗

Process Development for Automated Solar Cell and Module Production. Task 4: Automated Array Assembly

A baseline sequence for the manufacture of solar cell modules was specified. Starting with silicon wafers, the process goes through damage etching, texture etching, junction formation, plasma edge etch, aluminum back surface field formation, and screen printed metallization to produce finished solar cells. The cells were then series connected on a ribbon and bonded into a finished glass tedlar module. A number of steps required additional developmental effort to verify technical and economic feasibility. These steps include texture etching, plasma edge etch, aluminum back surface field formation, array layup and interconnect, and module edge sealing and framing.

Source record↗

STM imaging of electronic waves on the surface of Bi2Te3: topologically protected surface states and hexagonal warping effects

Scanning tunneling spectroscopy studies on high-quality Bi{sub 2}Te{sub 3} crystals exhibit perfect correspondence to ARPES data, hence enabling identification of different regimes measured in the local density of states (LDOS). Oscillations of LDOS near a step are analyzed. Within the main part of the surface band oscillations are strongly damped, supporting the hypothesis of topological protec- tion. At higher energies, as the surface band becomes concave, oscillations appear which disperse with a particular wave-vector that may result from an unconventional hexagonal warping term.

36 MATERIALS SCIENCE↗

Role of oligomer structures in the surface chemistry of amidinate metal complexes used for atomic layer deposition of thin films

The beginning steps of the thermal chemistry of Cu(I)-2-(tert-butylimino)-5,5-dimethyl-pyrrolidinate on metal surfaces were characterized using temperature-programmed desorption experiments and density functional theory (DFT). The relative stability of the initial dimer relative to its dissociation on metal surfaces was evaluated. Several molecular desorption temperatures were identified on Ni(110), but all correspond to dimers, either containing the initial Cu ions or after their removal; no monomer was ever detected. DFT calculations also indicated preferential bonding on Cu(110) as a dimer, albeit with a distorted configuration, via the Cu atoms and in registry with the lattice of the substrate. Furthermore, a potential dissociation pathway of the adsorbed dimer was identified involving the partial detachment of the ligands via the scission of one Cu–N bond at the time and migration to adjacent surface sites. This process is accompanied by the reduction of the Cu centers of the metal–organic complex, indicating that it may be the rate-limiting reaction that leads to further fragmentation of the ligands.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗