Results for “Acceleration methods” — Page 71

DOE OSTI2023

Visual, Optical and Replica Inspections: Surface Preparation of 650 MHz NB Cavity for PIP-II Linac

Surface preparation of niobium superconducting RF cavities is a critical step for achieving good RF performance under the superconducting state. Surface defect, roughness, and contamination affect the accelerating gradient and quality factor of the cavities. We report surface inspection methods used to control the surface processing of 650 MHz cavities designated for the pre-production and prototype cryomodules for PIP-II linac. The cavity surface was routinely inspected visually, with an optical camera, and by microscopic scanning of surface replicas. This article covers details on the surface inspection methods and surface polishing process used to repair the surface.

43 PARTICLE ACCELERATORS↗

NASA NTRS2022

Accelerance Decoupling: An Approach for Removing the Influence of the Test Stand from the Integrated Modal Test

The main objective for launch vehicle (LV) modal testing is to quantify the LV’s modal properties in the free-free state (post pad separation). However, given the size of most LV systems, free-free testing is a challenge and often not feasible. With this, a test stand, typically the launch pad itself, is introduced as the means of support. This shifts the challenge to developing robust numerical methods for removing the influence of the launch pad from the integrated system modal test. The Space Launch System (SLS) is no exception where the mobile launcher (ML) is used to support the vehicle for the integrated modal test (IMT). For the IMT, it is well understood from pre-test analysis with finite element models (FEMs) of the SLS and SLS coupled to ML that the ML has a significant influence on the SLS modal properties especially in the lower frequency range where the primary SLS bending modes exist. An accelerance decoupling (AD) method has been formulated for the purpose of “subtracting out” the influence of the ML from the IMT results. With AD, the SLS decoupled frequency response functions (FRFs) are directly extracted from the IMT FRFs. The subject approach is aimed to utilize measured data only and achieve a robust FRF decoupling scheme. AD is derived from a widely used coupling technique called “Receptance Coupling” (RC). The AD core equation reverses the RC process and utilizes a pair of auxiliary equations that enable the core equation to be resolved based on measured data only. In AD, the decoupled component FRFs are extracted from the coupled system FRFs with a transformation to remove the contribution of the “subtractive component”. This paper addresses the AD’s operational flexibility to resolve SLS free-free modal properties from coupled system measured data but also the possibility to include data from FEM if there is enough confidence in the FEM or if it is asserted that the effect to the final outcome is reasonable.

Accelerance decoupling↗

NASA NTRS2022

Accelerance Decoupling: An Approach for Removing the Influence of the Test Stand from the Integrated Modal Test

The main objective for launch vehicle (LV) modal testing is to quantify the LV’s modal properties in the free-free state (post pad separation). However, given the size of most LV systems, free-free testing is a challenge and often not feasible. With this, a test stand, typically the launch pad itself, is introduced as the means of support. This shifts the challenge to developing robust numerical methods for removing the influence of the launch pad from the integrated system modal test. The Space Launch System (SLS) is no exception where the mobile launcher (ML) is used to support the vehicle for the integrated modal test (IMT). For the IMT, it is well understood from pre-test analysis with finite element models (FEMs) of the SLS and SLS coupled to ML that the ML has a significant influence on the SLS modal properties especially in the lower frequency range where the primary SLS bending modes exist. An accelerance decoupling (AD) method has been formulated for the purpose of “subtracting out” the influence of the ML from the IMT results. With AD, the SLS decoupled frequency response functions (FRFs) are directly extracted from the IMT FRFs. The subject approach is aimed to utilize measured data only and achieve a robust FRF decoupling scheme. AD is derived from a widely used coupling technique called “Receptance Coupling” (RC). The AD core equation reverses the RC process and utilizes a pair of auxiliary equations that enable the core equation to be resolved based on measured data only. In AD, the decoupled component FRFs are extracted from the coupled system FRFs with a transformation to remove the contribution of the “subtractive component”. This paper addresses the AD’s operational flexibility to resolve SLS free-free modal properties from coupled system measured data but also the possibility to include data from FEM if there is enough confidence in the FEM or if it is asserted that the effect to the final outcome is reasonable.

Accelerance decoupling↗

NASA NTRS2022

Accelerance Decoupling: An Approach for Removing the Influence of the Test Stand from the Integrated Modal Test

The main objective for launch vehicle (LV) modal testing is to quantify the LV’s modal properties in the free-free state (post pad separation). However, given the size of most LV systems, free-free testing is a challenge and often not feasible. With this, a test stand, typically the launch pad itself, is introduced as the means of support. This shifts the challenge to developing robust numerical methods for removing the influence of the launch pad from the integrated system modal test. The Space Launch System (SLS) is no exception where the mobile launcher (ML) is used to support the vehicle for the integrated modal test (IMT). For the IMT, it is well understood from pre-test analysis with finite element models (FEMs) of the SLS and SLS coupled to ML that the ML has a significant influence on the SLS modal properties especially in the lower frequency range where the primary SLS bending modes exist. An accelerance decoupling (AD) method has been formulated for the purpose of “subtracting out” the influence of the ML from the IMT results. With AD, the SLS decoupled frequency response functions (FRFs) are directly extracted from the IMT FRFs. The subject approach is aimed to utilize measured data only and achieve a robust FRF decoupling scheme. AD is derived from a widely used coupling technique called “Receptance Coupling” (RC). The AD core equation reverses the RC process and utilizes a pair of auxiliary equations that enable the core equation to be resolved based on measured data only. In AD, the decoupled component FRFs are extracted from the coupled system FRFs with a transformation to remove the contribution of the “subtractive component”. This paper addresses the AD’s operational flexibility to resolve SLS free-free modal properties from coupled system measured data but also the possibility to include data from FEM if there is enough confidence in the FEM or if it is asserted that the effect to the final outcome is reasonable.

Accelerance decoupling↗

NASA NTRS2018

Historical Perspective on Fast Coupled Loads Analysis Methods

Spacecraft structural designs are typically verified through a coupled loads analysis (CLA) process, which couples the spacecraft model with the launch vehicle (LV) model to predict low-frequency quasi-static and dynamic responses. The CLA calculations are typically the responsibility of the LV organization, but the spacecraft organization has a vested interest in being able to calculate approximate CLA results during the design of the spacecraft. Because of this, there has long been interest in a method that would allow a spacecraft organization to perform a CLA without access to the full set of LV models and forcing functions. One such method is the Norton-Thevenin Receptance Coupling (NTRC) approach, which is specifically designed to accurately transform LV free accelerations (no payload) into coupled system accelerations (LV plus payload). The purpose of this report is to provide historical context for the NTRC method and compare it with methods that have been used in the past. In particular, it is compared to a frequency-domain substitution method that had been used for a long period of time at the Jet Propulsion Laboratory, and a component-mode-based equivalent to that method.

Blelloch, Paul A.↗

DOE OSTI2024

On detrending stream velocity time series for robust tidal flow turbulence characterization

We investigated the impact of detrending techniques on turbulence quantities from tidal stream flow data, focusing on the autocorrelation function, $ρ_{uu}$, and velocity spectrum, $Φ(f)$. Standard detrending methods, including high-pass frequency-based and polynomial-based techniques, are examined, alongside a proposed alternative method, the empirical mode decomposition (EMD). Our results highlight that intervals of flow acceleration and deceleration, typical in tidal and riverine flows, significantly affect the estimation of turbulence quantities using high-pass frequency filtering and polynomial detrending of varying orders. These methods can strongly influence $ρ_{uu}$ and $Φ(f)$, thereby affecting the accurate estimation of derived quantities. We examine two variations of detrending data using EMD; the first removes only the EMD residue, and the second removes both the residue and the largest scale intrinsic mode function (IMF). By comparing the detrended spectra with the modeled von Kármán spectra, we demonstrate that the second variation (i.e., removing the residue and the largest scale IMF) successfully removed the large-scale trend of the data while retaining the energy of other scales.

Detrend↗

DOE OSTI2021

Accelerating the development of new solar absorbers by photoemission characterization coupled with density functional theory

Abstract The expectation to progress towards Terawatts production by solar technologies requires continuous development of new materials to improve efficiency and lower the cost of devices beyond what is currently available at industrial level. At the same time, the turnaround time to make the investment worthwhile is progressively shrinking. Whereas traditional absorbers have developed in a timeframe spanning decades, there is an expectation that emerging materials will be converted into industrially relevant reality in a much shorter timeframe. Thus, it becomes necessary to develop new approaches and techniques that could accelerate decision-making steps on whether further research on a material is worth pursuing or not. In this review, we will provide an overview of the photoemission characterization methods and theoretical approaches that have been developed in the past decades to accelerate the transfer of emerging solar absorbers into efficient devices.

14 SOLAR ENERGY↗

DOE OSTI2018

Diagnostics for Undersampling and Clustering in Monte Carlo Criticality Calculations

For the past 40 years, it has been known from the theoretical work of Gelbard [1] and Brissenden [2] that the results from Monte Carlo (MC) criticality calculations are biased if the number of neutrons per generation is not sufficiently large. The computed k-effective eigenvalue will be lower than the actual eigenvalue, and the computed eigenfunction will be too low in high-importance regions and too high in low-importance regions. This difficulty is commonly called the undersampling problem for criticality calculations. The biases for undersampling were confirmed for practical, realistic problems with modern MC codes by Brown [3]. The solution to undersampling is simple - use a larger number of neutrons per generation to reduce the biases to levels that are negligible. Over the past few years, the OECD-NEA-WPNCS Expert Group on Advanced Monte Carlo Techniques (EGAMCT) [4,5,6] investigated an extreme form of undersampling called clustering. When the number of neutrons per generation is small, neutrons in successive generations tend to group together (cluster) due to correlations, and the clusters tend to migrate through the problem space. While the problems of undersampling and clustering are well known and well understood theoretically, there were no existing diagnostics for MC codes to determine whether a given calculation is using sufficient neutrons per generation to eliminate these problems. That is, no tools were available to diagnose biases due to undersampling or clustering. The tools described herein resolve this longstanding problem by providing 2 robust methods for detecting undersampling and clustering in MC criticality calculations. The diagnosis of undersampling and clustering is part of a larger effort to thoroughly overhaul the calculational methods for criticality problems, providing for automated sampling of the initial fission distribution, acceleration of the iteration convergence process, automated detection of convergence in the iterations and starting of the active tally cycles, and the diagnosis of undersampling. All of these new methods have been prototyped in a local modified version of mcnp6.2 [7] and tested on a variety of critical systems.

74 ATOMIC AND MOLECULAR PHYSICS↗

NASA NTRS2006

In-Vacuum Photogrammetry of a Ten-Meter Square Solar Sail

Solar sailing is a promising, future in-space propulsion method that uses the small force of reflecting sunlight to accelerate a large, reflective membrane without expendable propellants. One of two solar sail configurations under development by NASA is a striped net approach by L'Garde, Inc. This design uses four inflatably deployed, lightweight booms supporting a network of thin strings onto which four quadrants of ultrathin aluminized membranes are attached. The NASA Langley Research Center (LaRC) provided both experimental and analytical support to L'Garde for validating the structural characteristics of this unique, ultralightweight spacecraft concept. One of LaRC's responsibilities was to develop and apply photogrammetric methods to measure sail shape. The deployed shape provides important information for validating the accuracy of finite-element modeling techniques. Photogrammetry is the science and art of calculating 3D coordinates of targets or other distinguishing features on structures using images. A minimum of two camera views of each target is required for 3D determination, but having four or more camera views is preferable for improved reliability and accuracy. Using retroreflective circular targets typically provides the highest measurement accuracy and automation. References 3 and 4 provide details of photogrammetry technology, and reference 5 discusses previous experiences with photogrammetry for measuring gossamer spacecraft structures such as solar sails. This paper discusses the experimental techniques used to measure a L Garde 10-m solar sail test in vacuum with photogrammetry. The test was conducted at the NASA-Glenn Space Power Facility (SPF) located at Plum Brook Station in Sandusky, Ohio. The SPF is the largest vacuum chamber in the United States, measuring 30 m in diameter by 37 m in height. High vacuum levels (10(exp -6) torr) can be maintained inside the chamber, and cold environments (-195 C) are possible using variable-geometry cryogenic cold walls. This test used a vacuum level of approximately 1 torr (sufficient for structural static/dynamic characterization) and instead of using the cryogenic cold walls, used local LN2 cold plates underneath each of the four cold-rigidizable solar sail booms instead.

Pappa, Richard S.↗

DOE OSTI2020

The role of the spatial heterogeneity and correlation length of surface wettability on two-phase flow in a CO 2 -water-rock system

This study characterized and modeled heterogeneous surface wettability in sandstone and investigated the role of spatial heterogeneity and correlation length of surface wettability on relative permeability in a supercritical CO 2 (scCO 2 )-brine-rock system. Understanding the role of wettability heterogeneity on relative permeability is essential to geological CO 2 sequestration, oil and gas recovery, and contaminated groundwater remediation. Although numerous studies have attempted to understand the influences of surface wettability, capillary number (Ca), and viscosity ratio, the role of the spatial variation and correlation length of surface wettability on two-phase flow in three-dimensional (3D) porous media has not been unraveled due to the challenges in the measurement and representation of realistic rock surface wettability. In this work, we conducted in-situ measurements of surface contact angle (CA) in a Bentheimer sandstone after CO 2 flooding using micro-computed tomography (micro-CT), and found that the pore-scale CA distribution on rock surfaces followed a log-normal distribution associated with a spatial correlation length. Based on the statistical information from CT scanning, a Gaussian random field was used to model CA distributions that had desired standard deviations and spatial correlation lengths, which were then adjusted within a certain range of values for sensitivity analyses to study their combined effects on the two-phase flow in the porous medium using the lattice Boltzmann (LB) method. The LB two-phase flow simulation was accelerated using hybrid, multicore parallel computing to overcome the challenges in simulating multiphase flow in a large 3D domain having 800 × 800 × 600 nodes. The simulation results showed that the surface wettability heterogeneity (i.e., standard deviation of CA) had a lesser effect on the relative permeability of the wetting fluid (water) but a more significant impact on the relative permeability of the non-wetting fluid (scCO 2 ). The Corey model was used to fit the LB-simulated relative permeability curves of water and scCO 2 and showed that the variations in the relative permeability curves for both water and scCO 2 increased as the standard deviation and spatial correlation length of CA increased. This study illustrated that the assumption of homogeneous surface wettability may cause errors in multiphase flow simulations. Furthermore, the impacts of both the standard deviation and spatial correlation length of CAs should be accounted for. This is the first study that explored the spatial correlation lengths associated with CA distributions on sandstone surfaces and comprehensively investigated the roles of both spatial variation and correlation length of CA on two-phase flow properties in 3D porous media. The optimized LB multiphase flow model was proved a powerful tool to study the interplays and combined effects of these statistical parameters, which had critical applications in numerous natural and engineering processes that involved multiphase flow in porous media.

58 GEOSCIENCES↗

DOE OSTI2022

Four-dimensional emittance measurement at the Spallation Neutron Source

A coasting hadron beam with an elliptical transverse profile, uniform charge density, and small transverse four-dimensional (4D) emittance could improve accelerator performance in several contexts. A phase space painting method to generate such a distribution is being tested in the Spallation Neutron Source (SNS) accumulator ring. A critical component of these efforts is to measure the 4D emittance of the beam during accumulation. The 4D emittance can be reconstructed from measured beam profiles in two ways: in the multi-optics method, the optics between a reconstruction and measurement location are varied; in the fixed-optics method, multiple measurement locations are used without modifying the optics. The fixed-optics method is faster but can lead to large uncertainty in the reconstructed 4D emittance. In this paper, we implement a variant of the multi-optics method using the four available wire-scanners near the SNS target. We also modify the wire-scanner region to reduce the uncertainty of the fixed-optics method. We then demonstrate the usefulness of the fixed-optics method by reconstructing the 4D emittance evolution during accumulation in the SNS ring.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2025

Determination of the nat Ti(d,x) 49 V excitation function by liquid scintillation analysis

Here, the experimental cross-sections for deuteron-induced nuclear reactions on natural titanium were measured using the stacked-foil method. Deuteron beams were provided by a Pelletron tandem accelerator at incident energies up to 8 MeV. The cross-sections for the production of 49 V were determined by liquid scintillation analysis, with the highest measured value of 522(32) mb occurring at 5.59(9) MeV. Additionally, the cross-sections for the production of 44m,46,47,48 Sc and 48 V were evaluated using gamma-ray spectroscopy and compared to some available literature.

43 PARTICLE ACCELERATORS↗

DOE OSTI2024

Efficient Parameterization of Density Functional Tight-Binding for 5 f -Elements: A Th–O Case Study

Density functional tight binding (DFTB) models for f-element species are challenging to parametrize owing to the large number of adjustable parameters. The explicit optimization of the terms entering the semiempirical DFTB Hamiltonian related to f orbitals is crucial to generating a reliable parametrization for f-block elements, because they play import roles in bonding interactions. However, since the number of parameters grows quadratically with the number of orbitals, the computational cost for parameter optimization is much more expensive for the f-elements than for the main group elements. In this work we present a set of efficient approaches for mitigating the hurdle imposed by the large size of the parameter space. A novel group-by-orbital correction functions for two-center bond integrals was developed. With this approach the number of parameters is reduced, and it grows linearly with the number of elements, maintaining the accuracy and the number of parameters, in the case of f elements, by more than 40%. The parameter optimization step was accelerated by means of the mini-batch BFGS method. This method allows parameter optimizations with much larger training sets than other single batch methods. A stochastic optimizer was employed that helped overcome shallow local minima in the objective function. The proposed algorithm was used to parametrize the DFTB Hamiltonian for the Th–O system, which was subsequently applied to the study of ThO 2 nanoparticles. The training set consisted of 6322 unique structures, which is barely feasible with conventional optimization methods. The optimized parameter set, LANL-ThO, displays good agreement with DFT-calculated properties such as energies, forces, and structures for both clusters and bulk ThO 2 . Benefiting from the fewer number of parameters and lower computational costs for objective function evaluations, this new approach shows its potential applications in DFTB parametrization for elements with high angular momentum, which present a challenge to conventional methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Nuclear Science for the Manhattan Project and Comparison to Today’s ENDF Data

Nuclear physics advances in the United States and Britain from 1939 to 1945 are described. The Manhattan Project’s work led to an explosion in our knowledge of nuclear science. A conference in April 1943 at Los Alamos provided a simple formula used to compute critical masses and laid out the research program needed to determine the key nuclear constants. In short order, four university accelerators were disassembled and reassembled at Los Alamos, and methods were established to make measurements on extremely small samples owing to the initial lack of availability of enriched 235U and plutonium. I trace the program that measured fission cross sections, fission-emitted neutron multiplicities and their energy spectra, and transport cross sections, comparing the measurements with our best understanding today as embodied in the Evaluated Nuclear Data File ENDF/B-VIII.0. The large nuclear data uncertainties at the beginning of the project, which often exceeded 25% to 50%, were reduced by 1945 often to less than 5% to 10%. Uranium-235 and plutonium-239 fission cross-section assessments in the fast mega-electron-volt range were reduced following more accurate measurements, and the neutron multiplicity $\overline{v}$ increased. By a lucky coincidence of canceling errors, the initial critical mass estimates were close to the final estimated masses. Some images from historical documents from our Los Alamos archives are shown. Many of the original measurements from these early years have not previously been widely available. Through this work, these data have now been archived in the international experimental nuclear reaction data library (EXFOR) in a collaboration with the International Atomic Energy Agency and Brookhaven National Laboratory.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2024

Heritable, multinucleotide deletions in plants using viral delivery of a repair exonuclease and guide RNAs

Abstract CRISPR/Cas9-mediated mutagenesis typically results in short insertion/deletion mutations, which are often too small to disrupt the function of cis-acting regulatory elements. Here, we describe a highly efficient in planta gene editing approach called VirTREX2-HLDel that achieves heritable multinucleotide deletions in both protein-coding genes and noncoding DNA regulatory elements. VirTREX2-HLDel uses RNA viruses to deliver both the 3 prime repair exonuclease 2 (TREX2) and single-guide RNAs. Our method enables recovery of multiplexed heritable deletions and increases the heritable gene editing frequency at poorly edited sites. We identified functional conservation and divergence of MICRORNA164 (miR164) in Nicotiana benthamiana and tomato (Solanum lycopersicum) using VirTREX2-HLDel and observed previously uncharacterized phenotypes in plants with large deletions at this locus. Our viral delivery method reduces the need for tissue culture and will accelerate the understanding of protein-coding and regulatory regions in plants.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Measurement of the nucleon spin structure functions for 0.01 < 𝑄 2 < 1 GeV 2 using CLAS

The spin structure functions of the proton and the deuteron were measured during the EG4 experiment at Jefferson Lab in 2006. Data were collected for longitudinally polarized electron scattering off longitudinally polarized NH 3 and ND 3 targets, for 𝑄 2 values as small as 0.012 and 0.02 GeV 2 , respectively, using the CEBAF Large Acceptance Spectrometer. This is the archival paper of the EG4 experiment that summarizes the previously reported results of the polarized structure functions 𝑔 1 , 𝐴 1 ⁢𝐹 1 , and their moments $\bar{Γ}$ 1 , $\bar{𝛾}$ 0 , and $\bar{𝐼}$ TT , for both the proton and the deuteron. In addition, we report on new results on the neutron 𝑔 1 extracted by combining proton and deuteron data and correcting for Fermi smearing, and on the neutron moments $\bar{Γ}$ 1 , $\bar{𝛾}$ 0 , and $\bar{𝐼}$ TT formed directly from those of the proton and the deuteron. Our data are in good agreement with the Gerasimov-Drell-Hearn sum rule for the proton, deuteron, and neutron. Furthermore, the isovector combination was formed for 𝑔 1 and the Bjorken integral $\bar{Γ}^{𝑝−𝑛}_1$, and it was compared to available theoretical predictions. All of our results, to the best of our knowledge, provide for the first time extensive tests of spin observable predictions from chiral effective field theory (𝜒⁢EFT) in a 𝑄 2 range commensurate with the pion mass. Finally, they motivate further improvement in 𝜒⁢EFT calculations from other approaches such as the lattice gauge method.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Inference of response functions with the help of machine-learning algorithms

Response functions are a key quantity to describe the near-equilibrium dynamics of strongly interacting many-body systems. Recent techniques that attempt to overcome the challenges of calculating these ab initio have employed expansions in terms of orthogonal polynomials. We employ a neural network prediction algorithm to reconstruct a response function 𝑆⁡(𝜔) defined over a range in frequencies 𝜔. Here, we represent the calculated response function as a truncated Chebyshev series whose coefficients can be optimized to reduce the representation error. We compare the quality of response functions obtained using coefficients calculated using a neural network (NN) algorithm with those computed using the Gaussian integral transform (GIT) method. In the regime where only a small number of terms in the Chebyshev series are retained, we find that the NN scheme outperforms the GIT method.

Kurkcuoglu, Doga Murat [Fermi National Accelerator↗

DOE OSTI2023

Accelerating crystal structure determination with iterative AlphaFold prediction

Experimental structure determination can be accelerated with artificial intelligence (AI)-based structure-prediction methods such as AlphaFold . Here, an automatic procedure requiring only sequence information and crystallographic data is presented that uses AlphaFold predictions to produce an electron-density map and a structural model. Iterating through cycles of structure prediction is a key element of this procedure: a predicted model rebuilt in one cycle is used as a template for prediction in the next cycle. This procedure was applied to X-ray data for 215 structures released by the Protein Data Bank in a recent six-month period. In 87% of cases our procedure yielded a model with at least 50% of C α atoms matching those in the deposited models within 2 Å. Predictions from the iterative template-guided prediction procedure were more accurate than those obtained without templates. It is concluded that AlphaFold predictions obtained based on sequence information alone are usually accurate enough to solve the crystallographic phase problem with molecular replacement, and a general strategy for macromolecular structure determination that includes AI-based prediction both as a starting point and as a method of model optimization is suggested.

59 BASIC BIOLOGICAL SCIENCES↗