Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

A comparison of wrought and powder metallurgical FeCrAl claddings under simulated LWR accident transients

Iron-chromium-aluminum (FeCrAl) alloys are potential accident tolerant fuel (ATF) cladding candidates for light-water reactors but are difficult to fabricate as thin-walled tubes via conventional cast-and-wrought routes. Powder metallurgy (PM) offers a manufacturing alternative with improved compositional control, but its transient accident performance has not been directly benchmarked against wrought variants. This study evaluates the burst behavior of commercially developed PM-processed FeCrAl alloys, PM-C26M (Fe-12Cr-6Al-2Mo) and the high precipitate density FA-SMT (Fe-22Cr-5Al-3Mo), under simulated light-water reactor accident transient conditions. Burst testing was conducted using the Severe Accident Test Station with heating rates of 5 °C/s and 50 °C/s and internal pressures ranging from 25 MPa to 100 MPa. PM-C26M reproduced wrought C26M burst behavior within 7–37 °C across the stress range, indicating that PM processing does not compromise transient strength. FA-SMT exhibited markedly higher burst temperatures and reduced heating-rate sensitivity, consistent with its engineered precipitate strengthening. FA-SMT rupture exhibited axial "unzipping" rather than the lateral tearing characteristic of PM- and wrought C26M. Post-test EBSD and fractography indicate that this behavior is strongly correlated with strain-gated intergranular void nucleation associated with the dense precipitate architecture of FA-SMT, a response absent in the comparatively clean PM-C26M matrix and consistent with rupture morphologies reported for oxide-dispersion strengthened (ODS) FeCrAl of similar base-matrix chemistry to PM-C26M. These findings highlight the potential of powder metallurgy as a viable fabrication route for ATF claddings from an accident performance standpoint.

Bell, Sam [ORNL] (ORCID:0000000251905657)↗

Sister Rod Destructive Examinations (FY23) Appendix I: SNF Aerosols Released During Rod Fracture

This report documents work performed under the Spent Fuel and Waste Disposition’s Spent Fuel and Waste Science and Technology program for the US Department of Energy (DOE) Office of Nuclear Energy (NE). This work was performed to fulfill Level 3 Milestone M3SF-23OR010201026, “FY23 M3 draft report on results from testing in FY23,” within work package SF-23OR01020102 and is an updated to the work reported in M2SF-23OR010201024, M2SF-22OR010201047, M2SF-21OR010201032, M2SF-19ORO010201026, and M2SF-19OR010201028. As a part of the DOE NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWd/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy. The SNF rods, called sister rods or sibling rods, are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin Zirc-4, ZIRLO, and M5. The DEs are being conducted to obtain a baseline of the HBU rods’ condition before dry storage and are focused on understanding overall SNF rod strength and durability. Fuel rods and defueled cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the post-irradiation examination data and the associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and subsequent disposition.This report documents the status of the ORNL Phase 1 DE activities related to the collection of SNF aerosol particles released during fuel rod fracture in 4-point bending in Phase 1 of the sister rod test program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sister Rod Destructive Examinations (FY22) Appendix I: SNF Aerosols Released During Rod Fracture

As a part of the DOE NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWd/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy. The SNF rods, called sister rods or sibling rods, are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin Zirc-4, ZIRLO, and M5. The DEs are being conducted to obtain a baseline of the HBU rods’ condition before dry storage and are focused on understanding overall SNF rod strength and durability. Fuel rods and defueled cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the post-irradiation examination data and the associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and subsequent disposition. This report documents the status of the ORNL Phase 1 DE activities related to the collection of SNF aerosol particles released during fuel rod fracture in 4-point bending in Phase 1 of the sister rod test program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Applying U.S. metal fuel experience to new fuel designs for fast reactors

With the increasing interest in small modular reactors or microreactors, developers are working to design and submit licensing approval requests of U–10Zr-fueled fast reactors. The developers and their proponents cite prior metal fuel experience (worldwide, but U.S. experience in particular for many developers) as the motivation and justification for their reactor concepts. The experience with metal fuel deployment in sodium-cooled fast reactors as well as the underlying irradiation testing database, provide a suitable basis for analytically justifying the use of metal fuel in new reactors. The evolution of metal fuel design and capability illustrates the importance of key fuel design parameters to consider in new applications of the prior experience: fuel smeared density, plenum-to-fuel volume ratio, the ratio of cladding radius to thickness, fuel composition, and cladding and duct materials. In-service operating and deployment conditions to be considered include fuel linear heat generation rate, fuel temperature, cladding temperature, peak burnup and peak fast fluence. Fuel designs and in-service conditions that are bounded by the database and experience are most easily addressed, but deviations from those previous parameters and conditions can be addressed by considering impacts on previously established behavior and applying other mitigating conservatisms, as appropriate. Here, the authors recommend any new deployment proceed with fuel surveillance and monitoring to mitigate risk, application of conservative measures to address uncertainties, and a fuel qualification program that addresses a range of in-service operating conditions with production fuel. The work reported should be of interest to students and regulators unfamiliar with metal fuel in fast reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sister Rod Destructive Examinations (FY23) Appendix C: Rod Internal Pressure, Void Volume, and Gas Transmission Tests

As a part of the DOE NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWD/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy. The SNF rods, called the sister rods or sibling rods, are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. The DEs are being conducted to obtain a baseline of the HBU rod’s condition before dry storage and are focused on understanding overall SNF rod strength and durability. Both fuel rods and empty cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the postirradiation examination data and the associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and consolidation activities. This appendix documents the status of the ORNL Phase 1 DE activities related to rod internal pressure and void volume measurement techniques, fission gas stack flow measurements applied to selected sister rods, and fission gas release calculations in Phase 1 of the sister rod test program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sister Rod Destructive Examinations (FY22) Appendix C: Rod Internal Pressure, Void Volume, and Gas Transmission Tests

As a part of the DOE NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWD/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy [C-1]. The SNF rods, called the sister rods or sibling rods, are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. The DEs are being conducted to obtain a baseline of the HBU rod’s condition before dry storage and are focused on understanding overall SNF rod strength and durability. Both fuel rods and empty cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the postirradiation examination data and the associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and consolidation activities. This appendix documents the status of the ORNL Phase 1 DE activities [C-2, C-3] related to rod internal pressure and void volume measurement techniques, fission gas stack flow measurements applied to selected sister rods, and fission gas release calculations in Phase 1 of the sister rod test program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Calibration and validation of NRC fuel performance models

FRAPCON and FRAPTRAN are the steady-state and transient fuel performance codes, respectively, that are used by the U.S. Nuclear Regulatory Commission (NRC) in performing confirmatory calculations of licensee fuel performance codes and safety analysis methods during the review and approval of these codes and methods for light-water reactors. The NRC also uses these codes to perform calculations to direct regulatory research and to assist in the development of new regulations and regulatory guides. FRAPCON and FRAPTRAN are well-validated fuel performance codes that are kept in a constant state of maintenance. FRAPCON and FRAPTRAN have an extensive database of separate effects data used to validate individual material property and fuel performance models and an integral effects database used to assess the overall code prediction within the full range of fuel operations. The key code predictions that are of regulatory interest as they relate to various specified acceptable design limits are: fuel and cladding temperature, rod internal pressure, cladding hoop strain, cladding corrosion and hydriding, and fission gas release. To assess the ability of the code to accurately predict these values, the integral assessment database consists of measurements of fuel centerline temperature, fission gas release, void volume, cladding corrosion, and cladding hoop strain. This paper will discuss the activities that are performed to ensure that FRAPCON and FRAPTRAN represent the state of the industry and will describe the separate effect and integral effect databases that are used to validate the models and are continually being expanded to ensure validation over the full range of fuel operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Purification of Zirconium Cladding Using a Chloride Volatility Process

The goal of this work is to investigate the thermochemistry of used fuel Zr cladding component chlorides as well as their activation products and residual radionuclide metal chlorides, in order to provide the DOE-NE community with fundamental data that will support the development of a chlorination process for the separation and purification of ZrCl 4 . Our studies will focus on the following elements: Zr, Sn, Fe, Cr, Sb, Nb and Cs; in the following sections, the term “chloride species” is applied to the following elements: Sn, Fe, Cr, Sb, Nb and Cs. Experimental and theoretical research will focus on the characterization, reactivity and volatility of the chloride species present in the ZrCl 4 obtained after chlorination of Zr cladding. The methods previously used for the purification of ZrCl 4 will be reexamined and the thermochemistry of the chloride species evaluated for each of the methods. Claddings of interest include Zircaloy-4, Zircaloy-2 and Zr-Nb alloys (Zirlo TM and Zr-2.5Nb). In this context, we propose five Tasks: Task 1: Computational study of the chemical form and thermochemical behavior of the chloride species produced after chlorination of Zr, Task 2: Characterization the chloride species obtained after chlorination of Zr cladding and Zr cladding components, Task 3 and Task 4: Study the thermochemical behavior of Zr cladding and Zr cladding complements in the presence of Cl 2 and HCl gas, and Task 5: Laboratory scale demonstrations of the removal of the impurity chloride species from ZrCl 4 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

RIA simulation tests using driver tube for ATF cladding

Pellet-cladding mechanical interaction (PCMI) is a potential failure mechanism for accident-tolerant fuel (ATF) cladding candidates during a reactivity-initiated accident (RIA). This report summarizes Fiscal Year (FY) 2017 research activities that were undertaken to evaluate the PCMI-like hoop-strain-driven mechanical response of ATF cladding candidates. To achieve various RIA-like conditions, a modified-burst test (MBT) device was developed to produce different mechanical pulses. The calibration of the MBT instrument was accomplished by performing mechanical tests on unirradiated Generation-I iron-chromium-aluminum (FeCrAl) alloy samples. Shakedown tests were also conducted in both FY 2016 and FY 2017 using unirradiated hydrided ZIRLO™ tube samples. This milestone report focuses on testing of ATF materials, but the benchmark tests with hydrided ZIRLO™ tube samples are documented in a recent journal article.a For the calibration and benchmark tests, the hoop strain was monitored using strain gauges attached to the sample surface in the hoop direction. A novel digital image correlation (DIC) system composed of a single high-speed camera and an array of six mirrors was developed for the MBT instrument to better resolve the failure behavior of samples and to provide useful data for validation of high-fidelity modeling and simulation tools. The DIC system enable a 360° view of a sample’s outer surface. This feature was added to the instrument to determine the precise failure location on a sample’s surface for strain predictions. The DIC system was tested on several silicon carbide fiber/silicon carbide matrix (SiC/SiC) composite tube samples at various pressurization rates of the driver tube (which correspond to the strain rates for the samples). The hoop strains for various loading conditions were determined for the SiC/SiC composite tube samples. Future work is planned to enhance understanding of the failure behavior of the ATF cladding candidates of age-hardened FeCrAl alloys and SiC/SiC composites in detail during RIA conditions informed by the computational studies performed under the US Department of Energy Office of Nuclear Energy Advanced Fuels Campaign. The testing instrument and the new DIC system will be further developed to reach different stress-state conditions and to perform tests at elevated temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Standalone BISON Fuel Performance Results for Watts Bar Unit 1, Cycles 1-3

The Consortium for Advanced Simulation of Light Water Reactors (CASL) is moving forward with more complex multiphysics simulations and increased focus on incorporating fuel performance analysis methods. The coupled neutronics/thermal-hydraulics capabilities within the Virtual Environment for Reactor Applications Core Simulator (VERA-CS) have become relatively stable, and major advances have been made in analysis efforts, including the simulation of twelve cycles of Watts Bar Nuclear Unit 1 (WBN1) operation. While this is a major achievement, the VERA-CS approaches for treating fuel pin heat transfer have well-known limitations that could be eliminated through better integration with the BISON fuel performance code. Several approaches are being implemented to consider fuel performance, including a more direct multiway coupling with Tiamat, as well as a more loosely coupled one-way approach with standalone BISON cases. Fuel performance typically undergoes an independent analysis using a standalone fuel performance code with manually specified input defined from an independent core simulator solution or set of assumptions. This report summarizes the improvements made since the initial milestone to execute BISON from VERA-CS output. Many of these improvements were prompted through tighter collaboration with the BISON development team at Idaho National Laboratory (INL). A brief description of WBN1 and some of the VERA-CS data used to simulate it are presented. Data from a small mesh sensitivity study are shown, which helps justify the mesh parameters used in this work. The multi-cycle results are presented, followed by the results for the first three cycles of WBN1 operation, particularly the parameters of interest to pellet-clad interaction (PCI) screening (fuel-clad gap closure, maximum centerline fuel temperature, maximum/minimum clad hoop stress, and cumulative damage index). Once the mechanics of this capability are functioning, future work will target cycles with known or suspected PCI failures to determine how well they can be estimated.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A Eulerian three-fluid flow framework for the study of fuel dispersal behavior under loss-of-coolant accident conditions

As the nuclear industry explores new fuel designs to accommodate increased burnup, studying fuel behavior during loss-of-coolant accidents is essential for ensuring the safe operation of light-water reactors. Here, this study presents a computational model to simulate the intricate three-phase flow dynamics of fuel dispersal following cladding breach, where solid fuel particles and carrier fission gases interact with the surrounding liquid or gas medium. The model utilizes a Eulerian three-fluid framework to depict the phase interaction within interpenetrating continua, treating fragmented fuel as granular material. Closure relationships for bulk-flow properties of the solid phase and detailed interfacial exchange terms in high-temperature, high-speed gas-solid-liquid flow scenarios are proposed. The model was validated using adiabatic experimental results in the literature, focusing on characterizing fuel dispersal behavior during loss-of-coolant accidents conditions. Settlement characteristics of the solids, quantified by the probability distribution of equivalent particles, closely matched probability density functions reported in experimental studies. Key highlights of this study include the theoretical description of a coupled three-phase flow with phase change, interpretation of the high-pressure boundary conditions and insights into the transient behavior of gas-solid-liquid phase dynamics during a simulated high-speed dispersal event.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Investigation of γ - ( U , Z r ) structural properties and its interfacial properties with liquid sodium using ab initio molecular dynamics

In this study, the elastic properties, structural parameters, sound velocity, and Debye temperature of γ–(U,Zr) were computed using ab initio molecular dynamics (AIMD) at temperatures between 1000 K and 1400 K and for Zr content between 0 at. % and 100 at. %. UZr is used as a metallic fuel for Sodium Fast Reactors (SFRs). The study of the mechanical and thermal behavior of these alloys leads to a better data-informed fuel design. The bulk modulus, shear modulus, Young's modulus, and Poisson's ratio were calculated from the elastic constants and their dependence on Zr content and temperature was investigated, comparing the results with previous computational work and the available experimental data in the literature. Interfacial properties between UZr (up to 32 at. % which typically exists in nuclear fuel) and liquid sodium are also of interest due to the presence of a sodium bond between the fuel and the cladding in metallic nuclear fuel. The interfacial energy between γ–(U,Zr) and liquid sodium, the surface tension of liquid sodium, and the work of adhesion were computed at different temperatures and Zr concentrations. It was demonstrated that γ–(U,Zr) is completely wetted by liquid sodium at all the investigated temperatures and Zr concentrations. Finally, this work provides the basis for the determination of interfacial resistances in SFRs and their implementation into heat transfer fuel performance simulations, which will be the subject of future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

$\mathrm{EBR-II MOX}$ Fuel Characterization Enabling ARES Phase I Testing

Pretransient characterization was performed for the Experimental Breeder Reactor II (EBR-II) mixed-oxide (MOX) fuel pellets from the SPA-2/-2B Operational Reliability Testing collaboration between Japan and the United States. Continued collaboration under the Advanced Reactor Experiments for Sodium Fast Reactor Fuels project will investigate the transient performance of these rods in the Transient Reactor Test facility at Idaho National Laboratory in the MOXTOP-THOR experiment. The results will fill a gap in existing transient performance data for MOX as these rods have a peak burnup of 14.3 at. % (~134.4 GWd/t) in the EBR-II. Fuel pellet properties were gathered from available resources and their irradiation and decay history evaluated. Further reactor physics calculations were performed to support the experiment design, reactor operations, and safety analyses necessary to enable the programmatic success of this effort. Of the three irradiated fuel pins, two will undergo transient testing, and all three will undergo post-irradiation examination. The methodology development and analysis activities utilized we report enable current experiment design work and provide the pathway through which measured data of this type can be further evaluated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Instrumented Lid Detailed Design

This report describes the design of an instrumented lid assembly for remote sampling, monitoring, and radiation testing (SMART) for demonstration and surveillance of the dry storage environment and fuel conditions of aluminum clad spent nuclear fuel (ASNF) in a Department of Energy (DOE) standardized canister. The lid assembly consists of a custom-designed lid and hat, together with a custom fuel basket. The functions and designs of each component of the lid assembly and the general arrangement of the lid assembly are provided in this report. The Piping and Instrumentation Diagram for the corresponding instruments which will be connected to the lid assembly is shown in the appendix. Details of the system to provide characterization are provided in SRNL-L2240-2019-00002, "Instrumented Lid - System Final Design". The detailed drawings of the lid assembly will be prepared following the specification of the demonstration and surveillance system, including canister, design, to which the lid will be matched. Individual testing of the lid assembly sensor components will be performed in cold testing. The lid assembly including connection ports for gas sampling and thermowells will be fabricated. The tubing of the lid assembly to which the sensor components will be connected will not be assembled. The final design of the lid assembly connections to instrumentation is dependent on the staging of the demonstration and surveillance canister.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

FY09 AFCI Advanced Oxide Fuel Development and Test Plan - LANL Plutonium Facility

This document provides a plan for advanced oxide transmutation fuel development and testing work in the Los Alamos National Laboratory (LANL) Plutonium Facility during FY09. This work builds upon work conducted during FY08, in which fuel pellets containing mixed oxides of uranium and plutonium (MOX) and minor actinide-bearing fuel pellets (MAMOX) were fabricated at LANL for the AFC2-C/D experiment and provided for irradiation testing in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). This work will be conducted under the Advanced Fuel Cycle Initiative (AFCI) funded by the Department of Energy Office of Nuclear Energy (DOE-NE). The cost and schedule of this project are documented in the AFCI planning and controls work package number LA0915010301, “Oxide Fuel - LANL”. Advanced nuclear fuel development efforts for AFCI to date have focused on the chemical and bulk mechanical properties of fuel pellets selected for irradiation testing. It is necessary to develop a fuel fabrication process that provides fuel pellets with a minimum of physical deformations such as cracks and chips, and that meet physical and chemical specifications for various parameters, such as actinide content and isotopic distribution. The bulk density of the fuel is needed for safety basis calculations, and estimates of swelling and fission gas retention. Dimensions must be specified for optimal heat transport across the gap between fuel and cladding, while providing for ease of pin loading. Fabrication processes for test fuels at LANL have satisfied these requirements. AFC2-C/D pellets have been fabricated to meet these specifications, and are currently undergoing irradiation in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). The focus of fuel development work performed in FY09 will be to develop further the understanding of fabrication of minor actinide bearing fuels. This understanding will support selection of fabrication parameters for future fuel compositions of interest for irradiation testing.

M2↗

Preliminary Evaluation of Loading DOE Standardized Canisters in the CPP-603 Irradiated Fuel Storage Facility

This evaluation looks at the equipment and operations necessary to load United States Department of Energy (DOE) -owned Spent Nuclear Fuel (SNF) into DOE SNF Standardized Canisters in the CPP-603 Irradiated Fuel Storage Facility in the Idaho Nuclear Technology and Engineering Center (INTEC) area at Idaho National Laboratory (INL). Two types of fuels are looked at in this evaluation: Advanced Test Reactor (ATR) fuel (uranium-aluminide fuel with aluminum cladding) and Peach Bottom fuel (thorium-uranium carbide fuel in a graphite matrix). The ATR fuel ready for loading would come from fuel storage canisters in the CPP-603 facility, while the Peach Bottom fuel ready for loading could come from either fuel storage canisters in the CPP-603 facility and or containers in the CPP-749 Underground Fuel Storage Facility – Generation I Vaults.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Architecture and Component Selection for the Remote Canister-Monitoring System

This report documents the selected system architecture and components surveyed for the development of a remote, canister-monitoring system (RCMS) for determining and monitoring environmental conditions within dry fuel storage canisters containing aluminum-clad spent nuclear fuel (ASNF) at Idaho National Laboratory (INL). These efforts are in support of the Department of Energy Office of Environmental Management (DOE-EM) investigations into the technical issues associated with extended dry storage (50+ years) of ASNF. It is important to resolve questions regarding storage because the ATR is expected to continue producing approximately 100 elements of spent fuel per year for at least another twenty years. The parameters to be monitored by the RCMS include temperature, relative humidity, hydrogen gas concentration, and radiation environment (dose). Components are selected based on the expected environmental conditions within the canister and fuel storage area and the desired performance of the RCMS. Several of these components have been purchased and are currently undergoing component testing to confirm their suitability for use in delivering the RCMS. Additional components may be identified through the course of design and may be selected in the future. Furthermore, changing performance, interfacing, and compatibility requirements and the results of component testing may necessitate revisiting component selection.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

LIFE Materials: Overview of Fuels and Structural Materials Issues Volume 1

The National Ignition Facility (NIF) project, a laser-based Inertial Confinement Fusion (ICF) experiment designed to achieve thermonuclear fusion ignition and burn in the laboratory, is under construction at the Lawrence Livermore National Laboratory (LLNL) and will be completed in April of 2009. Experiments designed to accomplish the NIF's goal will commence in late FY2010 utilizing laser energies of 1 to 1.3 MJ. Fusion yields of the order of 10 to 20 MJ are expected soon thereafter. Laser initiated fusion-fission (LIFE) engines have now been designed to produce nuclear power from natural or depleted uranium without isotopic enrichment, and from spent nuclear fuel from light water reactors without chemical separation into weapons-attractive actinide streams. A point-source of high-energy neutrons produced by laser-generated, thermonuclear fusion within a target is used to achieve ultra-deep burn-up of the fertile or fissile fuel in a sub-critical fission blanket. Fertile fuels including depleted uranium (DU), natural uranium (NatU), spent nuclear fuel (SNF), and thorium (Th) can be used. Fissile fuels such as low-enrichment uranium (LEU), excess weapons plutonium (WG-Pu), and excess highly-enriched uranium (HEU) may be used as well. Based upon preliminary analyses, it is believed that LIFE could help meet worldwide electricity needs in a safe and sustainable manner, while drastically shrinking the nation's and world's stockpile of spent nuclear fuel and excess weapons materials. LIFE takes advantage of the significant advances in laser-based inertial confinement fusion that are taking place at the NIF at LLNL where it is expected that thermonuclear ignition will be achieved in the 2010-2011 timeframe. Starting from as little as 300 to 500 MW of fusion power, a single LIFE engine will be able to generate 2000 to 3000 MWt in steady state for periods of years to decades, depending on the nuclear fuel and engine configuration. Because the fission blanket in a fusion-fission hybrid system is subcritical, a LIFE engine can burn any fertile or fissile nuclear material, including un-enriched natural or depleted U and SNF, and can extract a very high percentage of the energy content of its fuel resulting in greatly enhanced energy generation per metric ton of nuclear fuel, as well as nuclear waste forms with vastly reduced concentrations of long-lived actinides. LIFE engines could thus provide the ability to generate vast amounts of electricity while greatly reducing the actinide content of any existing or future nuclear waste and extending the availability of low cost nuclear fuels for several thousand years. LIFE also provides an attractive pathway for burning excess weapons Pu to over 99% FIMA (fission of initial metal atoms) without the need for fabricating or reprocessing mixed oxide fuels (MOX). Because of all of these advantages, LIFE engines offer a pathway toward sustainable and safe nuclear power that significantly mitigates nuclear proliferation concerns and minimizes nuclear waste. An important aspect of a LIFE engine is the fact that there is no need to extract the fission fuel from the fission blanket before it is burned to the desired final level. Except for fuel inspection and maintenance process times, the nuclear fuel is always within the core of the reactor and no weapons-attractive materials are available outside at any point in time. However, an important consideration when discussing proliferation concerns associated with any nuclear fuel cycle is the ease with which reactor fuel can be converted to weapons usable materials, not just when it is extracted as waste, but at any point in the fuel cycle. Although the nuclear fuel remains in the core of the engine until ultra deep actinide burn up is achieved, soon after start up of the engine, once the system breeds up to full power, several tons of fissile material is present in the fission blanket. However, this fissile material is widely dispersed in millions of fuel pebbles, which can be tagged as individual accountable items, and thus made difficult to divert in large quantities. Several topical reports are being prepared on the materials and processes required for the LIFE engine. Specific materials of interest include: (1) Baseline TRISO Fuel (TRISO); (2) Inert Matrix Fuel (IMF) & Other Alternative Solid Fuels; (3) Beryllium (Be) & Molten Lead Blankets (Pb/PbLi); (4) Molten Salt Coolants (FLIBE/FLiNaBe/FLiNaK); (5) Molten Salt Fuels (UF4 + FLIBE/FLiNaBe); (6) Cladding Materials for Fuel & Beryllium; (7) ODS FM Steel (ODS); (8) Solid First Wall (SFW); and (9) Solid-State Tritium Storage (Hydrides).

42 ENGINEERING↗