Search NASA⌕ Search

SEARCH · Search NASA

Results for “Multilayers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Pulsed laser ejection of single-crystalline III-V solar cells from GaAs substrates

The best III-V solar cells start out as single-crystalline multilayers on GaAs substrates. Separating these multilayers from their growth substrate enables higher performance and wafer reuse, which are both critical for terrestrial III-V solar cell viability. Here, we remove rigidly bonded, 16 mm 2 x 3.5μm thick devices from a GaAs substrate using an unfocused Nd:YAG laser pulse. The pulse is absorbed by a low-bandgap, lattice-matched layer below the device, driving an ablation event that ejected the crystalline multilayer from the substrate. Minutes of selective wet-chemical etching and device finishing yield a 0.1 cm 2 device with a 17.4% power conversion efficiency and open-circuit voltage of 1.07 V, using AM1.5 direct with no anti-reflection coating. We show that the performance is comparable to similar cells produced via conventional processes. We discuss unique process characteristics, such as the potential to separate wafer-sized solar cells per laser pulse.

14 SOLAR ENERGY↗
DOE OSTI2019

Desorption Kinetics of Carbon Dioxide from a Graphene Covered Pt(111) Surface

The interaction of carbon dioxide (CO2) with a graphene covered Pt(111) surface was investigated using temperature programmed desorption (TPD) and reflection absorption infrared spectroscopy (RAIRS). The TPD spectra show monolayer and multilayer desorption peaks, however, the multilayer peak is not well-separated from the monolayer peak. The TPD spectra for submonolayer and multilayer coverages align on separate common leading edges. This alignment is a signature of zero-order desorption kinetics. The RAIRS spectra for submonolayer coverages have a relatively sharp peak at ~2350 cm-1 which is assigned to the n 3 asymmetric stretch. The peak is observed at the onset of CO2 adsorption and the area of the peak increases linearly with coverage. This suggests that CO2 does not lie flat on the surface but instead has a component of its bond axis perpendicular to the graphene surface.

Smith, Ronald S.↗
DOE OSTI2017

Desorption Kinetics of Benzene and Cyclohexane from a Graphene Surface

The desorption kinetics for benzene and cyclohexane from a graphene covered Pt(111) surface were investigated using temperature programmed desorption (TPD). The benzene desorption spectra show well-resolved monolayer and multilayer desorption peaks. The benzene monolayer TPD spectra have the same desorption peak temperature and have line shapes which are consistent with first-order desorption kinetics. For benzene coverages greater than 1 ML, the TPD spectra align on a common leading edge which is consistent with zero-order desorption. An inversion analysis of the monolayer benzene TPD spectra yielded a desorption activation energy of 54 ± 3 kJ/mol with a prefactor of 1017 ± 1 s-1. The TPD spectra for cyclohexane also have well-resolved monolayer and multilayer desorption features. The desorption leading edges for the monolayer and the multilayer TPD spectra are aligned indicating zero-order desorption kinetics in both cases. An Arrhenius analysis of the monolayer cyclohexane TPD spectra yielded a desorption activation energy of 53.5 ± 2 kJ/mol with a prefactor of 1016 ± 1 ML s-1.

desorption kinetics↗
DOE OSTI2024

Adsorption Thermodynamics for Process Simulation

Adsorption has rapidly evolved in recent decades and is an established separation technology extensively practiced in gas separation industries and others. However, rigorous thermodynamic modeling of multicomponent adsorption equilibrium remains elusive, and industrial practitioners rely heavily on expensive and time-consuming trial-and-error pilot studies to develop adsorption units. Here, this article highlights the need for rigorous adsorption thermodynamic models and the limitations and deficiencies of existing models such as the extended Langmuir isotherm, dual-process Langmuir isotherm, and adsorbed solution theory. It further presents a series of recent advances in the generalization of the classical Langmuir isotherm of single-component adsorption by deriving an activity coefficient model to account for the adsorbed phase adsorbate–adsorbent interactions, substituting adsorbed phase adsorbate and vacant site concentrations with activities, and extending to multicomponent competitive adsorption equilibrium, both monolayer and multilayer. Requiring a minimum set of physically meaningful model parameters, the generalized Langmuir isotherm for monolayer adsorption and the generalized Brunauer–Emmett–Teller isotherm for multilayer adsorption address various thermodynamic modeling challenges including adsorbent surface heterogeneity, isosteric enthalpies of adsorption, BET surface areas, adsorbed phase nonideality, adsorption azeotrope formation, and multilayer adsorption. Also discussed is the importance of quality adsorption data that cover sufficient temperature, pressure, and composition ranges for reliable determination of the model parameters to support adsorption process simulation, design, and optimization.

09 BIOMASS FUELS↗
DOE OSTI2017

Nonlinear Layer-by-Layer Films: Effects of Chain Diffusivity on Film Structure and Swelling

Here in this paper, we report on the role of molecular diffusivity in the formation of nonlinearly growing polyelectrolyte multilayers (nlPEMs). Electrostatically bound polyelectrolyte multilayers were assembled from poly(methacrylic acid) (PMAA) as a polyanion and quaternized poly(2-(dimethylamino)ethyl methacrylate) (QPC) as a polycation. Film growth as measured by ellipsometry was strongly dependent on the time allowed for each polymer deposition step, suggesting that the diffusivities of the components are crucial in controlling the rate of film growth. Uptake of polyelectrolytes within nlPEMs was relatively slow and occurred on time scales ranging from minutes to hours, depending on the film thickness. Spectroscopic ellipsometry measurements with nlPEM films exposed to aqueous solutions exhibited high (severalfold) degrees of film swelling and different swelling values for films exposed to QPC or PMAA solutions. FTIR spectroscopy showed that the average ionization of film-assembled PMAA increased upon binding of QPC and decreased upon binding of PMAA, in agreement with the charge regulation mechanism for weak polyelectrolytes. The use of neutron reflectometry (NR) enabled quantification of chain intermixing within the film, which was drastically enhanced when longer times were allowed for polyelectrolyte deposition. Diffusion coefficients of the polycation derived from the uptake rates of deuterated chains within hydrogenated films were of the order of 10 –14 cm 2 /s, i.e., 5–6 orders of magnitude smaller than those found for diffusion of free polymer chains in solution. Exchange of the polymer solutions to buffer inhibited film intermixing. Taken together, these results contribute to understanding the mechanism of the growth of nonlinear polyelectrolyte multilayers and demonstrate the possibility of controlling film intermixing, which is highly desirable for potential future applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Two-Dimensional Tantalum Carbo-Selenide for Hydrogen Evolution

Herein, we report the synthesis of two-dimensional Ta 2 Se 2 C (2D-Ta 2 Se 2 C) nanosheets using electrochemical lithiation in multilayer Ta 2 Se 2 C followed by sonication in deionized water. Multilayer Ta 2 Se 2 C was obtained via solid-state synthesis of Fe x Ta 2 Se 2 C followed by chemical etching of Fe. 2D-Ta 2 Se 2 C exhibited promising electrocatalytic activity for the hydrogen evolution reaction from water compared to multilayer Ta 2 Se 2 C and 2D-TaSe 2 . 2D-Ta 2 Se 2 C showed an overpotential at 10 mA·cm -2 (η 10 ) of 264 mV, a Tafel slope of 91 mV·dec -1 , and an electrochemically active surface area of 17.61 m ECSA 2 ·g catalyst -1 . The high performance could be attributed to the large surface area of single sheets which hence maximizes the number of exposed catalytic sites and increased density of vacancies, observed with transmission electron microscopy, during synthesis and processing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Long-Range Charge Transport Facilitated by Electron Delocalization in MoS 2 and Carbon Nanotube Heterostructures

Controlling charge transport at the interfaces of nanostructures is crucial for their successful use in optoelectronic and solar energy applications. Mixed-dimensional heterostructures based on single-walled carbon nanotubes (SWCNTs) and transition metal dichalcogenides (TMDCs) have demonstrated exceptionally long-lived charge-separated states. However, the factors that control the charge transport at these interfaces remain unclear. In this study, we directly image charge transport at the interfaces of single- and multilayered MoS 2 and (6,5) SWCNT heterostructures using transient absorption microscopy. We find that charge recombination becomes slower as the layer thickness of MoS 2 increases. This behavior can be explained by electron delocalization in multilayers and reduced orbital overlap with the SWCNTs, as suggested by nonadiabatic (NA) molecular dynamics (MD) simulations. Dipolar repulsion of interfacial excitons results in rapid density-dependent transport within the first 100 ps. Stronger repulsion and longer-range charge transport are observed in heterostructures with thicker MoS 2 layers, driven by electron delocalization and larger interfacial dipole moments. These findings are consistent with the results from NAMD simulations. Our results suggest that heterostructures with multilayer MoS 2 can facilitate long-lived charge separation and transport, which is promising for applications in photovoltaics and photocatalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Substrate-Directed Dimensional and Phase Control of Peptide Assemblies on Two-Dimensional van der Waals Materials

Understanding and controlling biomolecular self-assembly on van der Waals (vdW) materials has the potential to advance hybrid bioelectronic devices by enabling precise tuning of the interface and modulation of the resulting electronic properties of the biomolecule-vdW heterostructure. However, how surface properties of vdW materials direct biomolecule assembly remains poorly understood. To fill this knowledge gap, we investigated the assembly of a peptide known to assemble into two-dimensional (2D) crystalline films on MoS 2 on three representative vdW surfaces: WS 2 , MoS 2 , and highly oriented pyrolytic graphite (HOPG). Using in situ atomic force microscopy (AFM), we find that assembly is substrate-dependent, resulting in multilayers on WS 2 , monolayers on MoS 2 , and multiple coexisting phases on HOPG. WS 2 exhibits a higher negative charge, strong long-range electrostatic interactions, and extensive hydration layering that may promote multilayer stacking. In contrast, MoS 2 has stronger short-range interactions with the peptides but much weaker long-range interactions and hydration structure, which may favor monolayer formation. Molecular dynamics simulations predict a corresponding switch from monolayer to multilayer aggregates of the adsorbed monomers, reflected in their relative mobilities. On hydrophobic HOPG, the peptides bind most strongly and remain as monomers with high surface mobility. The peptide dimers comprising the basic unit of the crystals are more compact on HOPG, which has a smaller lattice constant than WS 2 or MoS 2 , suggesting strain contributes to stabilizing multiple phases. Our results provide mechanistic insights into how surface charge and hydration structure, and the lattice structure of the substrates governs peptide assembly on vdW materials, offering a framework to rationally control the 2D peptide-vdW heterostructures.

Molecular dynamics simulations↗
DOE OSTI2020

Tuning the Chern number in quantum anomalous Hall insulators

A quantum anomalous Hall (QAH) state is a two-dimensional topological insulating state that has a quantized Hall resistance of h/(Ce 2 ) and vanishing longitudinal resistance under zero magnetic field (where h is the Planck constant, e is the elementary charge, and the Chern number C is an integer). The QAH effect has been realized in magnetic topological insulators and magic-angle twisted bilayer graphene. However, the QAH effect at zero magnetic field has so far been realized only for C = 1. Here we realize a well quantized QAH effect with tunable Chern number (up to C = 5) in multilayer structures consisting of alternating magnetic and undoped topological insulator layers, fabricated using molecular beam epitaxy. The Chern number of these QAH insulators is determined by the number of undoped topological insulator layers in the multilayer structure. Moreover, we demonstrate that the Chern number of a given multilayer structure can be tuned by varying either the magnetic doping concentration in the magnetic topological insulator layers or the thickness of the interior magnetic topological insulator layer. We develop a theoretical model to explain our experimental observations and establish phase diagrams for QAH insulators with high, tunable Chern number. Furthermore, the realization of such insulators facilitates the application of dissipationless chiral edge currents in energy-efficient electronic devices, and opens up opportunities for developing multi-channel quantum computing and higher-capacity chiral circuit interconnects.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Heating rate dependent ignition of Al/Pt nanolaminates through pulsed laser irradiation

Direct laser irradiation of sputter deposited Al/Pt nanolaminate multilayers results in rapid local heating and exothermic mixing of reactant layers. Milli- and microsecond pulsed laser irradiation under certain test conditions leads to single-point ignition of rapid, self-propagating, formation reactions. Multilayers having bilayer thicknesses of 328 nm, 164 nm, and 65 nm are characterized by their ignition onset times and temperatures. Smaller bilayer thickness multilayers require less laser intensity for ignition compared with larger bilayer designs (when utilizing a particular pulse duration). The relationship between laser intensity and ignition onset time is used to calibrate an activation energy for ignition within a finite element reactive heat transport model. The local heating rate is varied from 10 4 K/s to 10 6 K/s by selecting a laser intensity. Kissinger analysis was performed on the heating rate-dependent ignition temperatures measured with high speed pyrometry to experimentally determine an activation energy in the foils of (6.2 ± 1.6 × 10 4 J/mole atoms). Furthermore, this value is then compared to an activation energy produced from model fits to an ignition onset time of 7.2 × 10 4 J/mole atoms.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A nonlinear interface integrated lever mechanism for piezoelectric footstep energy harvesting

Harnessing footstep energy allows for a unique method of power generation from a largely untapped resource, with applications such as instantly charging mobile and wearable electronic devices. This letter presents an easily integrated heel charger to efficiently convert kinematic walking energy into electricity. The heel charger uses a multilayered levered piezoelectric (L-Pie) mechanism associated with a nonlinear mechanical-synchronized switching on inductor circuit (M-SSHI) interface. It tactfully switches on when the foot contacts the ground, and switches off when the foot is lifted. This design takes full advantage of the user's weight, and amplifies footstep displacement by utilizing the lever mechanism to gain maximum deformation of multilayer piezoelectric patches. The experimental results show that the fabricated two-level multilayer L-pie has a top performance of 13.60 mW of AC RMS, a mechanical to AC power conversion efficiency of 7.87%, and a DC RMS power of 6.13 mW, an AC to DC power conversion efficiency of 45.07%, under a harmonic excitation of 2.3 Hz (mimicking fast walking speed: 6.2 km/h for men, 5.55 km/h for women). With an optimal load of 210 kΩ, the two-level L-pie using the M-SSHI has an improvement of 206.45% in DC RMS power compared to a standard 4-diode bridge energy harvesting circuit. Finally, the L-pie design works more efficiently under large force excitation, even with small displacement, which makes this technology optimal for footstep energy harvesting.

42 ENGINEERING↗
DOE OSTI2024

Dissecting neurofilament tail sequence-phosphorylation-structure relationships with multicomponent reconstituted protein brushes

Neurofilaments (NFs) are multisubunit, bottlebrush-shaped intermediate filaments abundant in the axonal cytoskeleton. Each NF subunit contains a long intrinsically disordered tail domain, which protrudes from the NF core to form a “brush” surrounding each NF. Precisely how the tails’ variable charge patterns and repetitive phosphorylation sites mediate their conformation within the brush remains an open question in axonal biology. We address this problem by grafting recombinant NF tail protein constructs NF-Light, -Medium, and -Heavy (NFL, NFM, and NFH) to surfaces, yielding protein brushes of defined stoichiometry that can be phosphorylated in vitro. Atomic force microscopy measurements reveal that brush height depends on composition monotonically but not always linearly for binary NFL:NFM or NFL:NFH systems, and that NFM-based brushes are highly extended, while brushes incorporating the much larger NFH are surprisingly compact even after multisite phosphorylation. Complementary self-consistent field theory (SCFT) predicts multilayer brush morphologies for NFM and phosphorylated NFH brushes. Further experiments and SCFT analysis with designed mutants reveal that N-terminal negative charges in the NFH tail repel phosphorylated residues to generate the multilayer morphology, while the C-terminal charge-neutral region contributes to multilayer brush morphology but not total brush height. Charge-shuffled NFM variants show that charge segregation promotes brush collapse near physiological ionic strengths. Collectively, this study supports a role for NFM in establishing a dynamic range for NF brush conformation, lending insight into previous in vitro and in vivo findings. More broadly, this work establishes a platform for dissecting contributions of disordered protein sequence to conformation at interfaces.

Science & Technology - Other Topics↗
DOE OSTI2019

Preparing for the Next Generation of EUV Lithography at the Center for X-ray Optics

The introduction of EUV lithography into high-volume semiconductor manufacturing this year represents a monumental milestone for EUV technology. After nearly 30 years of development, the EUV research community has overcome many of the key obstacles required to enable the long-awaited integration of EUV lithography into the lab. These obstacles have included: the development of a stable, high-powered EUV source to ensure adequate exposure tool reliability; controlling EUV mask defects and mask contamination; and the development of EUV resists with adequate sensitivity, resolution, and line width roughness to meet the tolerances required for high-volume manufacturing. As EUV moves into its second generation, there will be new challenges facing the community as it works to push EUV technology into the future. Smaller feature sizes will be achieved using higher numerical aperture optics, which are planned to have an anamorphic geometry (asymmetric magnification and numerical aperture between horizontal and vertical axes) to overcome 3D effects at the mask. This new geometry and its larger angle ranges make understanding mask absorber and multilayer effects all the more important. New methods for high-NA wavefront metrology need to be tested to ensure that these optical systems can be aligned to operate with minimal aberrations. Mask defects need to continue to be studied, and the inclusion of EUV pellicles in the roadmap requires that mask inspection and review systems adapt accordingly. Finally, new resists must be developed to support the increased resolution of feature sizes below 8 nm half pitch. The Center for X-ray Optics (CXRO) at Berkeley Lab has been a leader in EUV research for the past 25 years. Leveraging 13.5 nm EUV light from the Advanced Light Source synchrotron facility, CXRO is home to several EUV and soft X-ray (SXR) research tools that have provided important insights into EUV resists, masks, and coatings. The 0.3 NA Microfield exposure tool (MET) and Dose Calibration Tool (DCT) have played an instrumental role in the development of the current generation of high-resolution EUV resists. The Actinic Inspection Tool (AIT) and its successor, SHARP, have enabled aerial image analysis, providing key insights into mask defects, 3D mask effects, illumination, and aberrations. And the CXRO Reflectometer continues to be the industry standard in multilayer coating and EUV mask scattering metrology. To address the new challenges facing the next generation of EUV lithography, CXRO has upgraded its suite of EUV research tools. The 0.5 NA MET5 is a newly commissioned projection lithography tool that is capable of printing feature sizes down to 8 nm half pitch. A new radiation chemistry program is deploying several techniques aimed at dissecting the role of primary photoelectrons and secondary electrons in EUV resists. The SHARP microscope has been outfitted with anamorphic zone plate lenses that can emulate the geometry of next-generation EUV scanners, and the reflectometer has been applied to new scattering experiments for the purpose of understanding the 3D effects of EUV mask multilayers, as well as determining mask properties using scattering profiles. In parallel with these tools, the CXRO High-NA Wavefront Sensing Program is developing high-resolution wavefront sensors suitable for measuring aberrations at high NA. This article presents an overview of these programs and describes how they will address the primary challenges that face the EUV community as it moves to the next generation of EUV lithography.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Canted standing spin-wave modes of permalloy thin films observed by ferromagnetic resonance

Non-collinear spin structures in materials that combine perpendicular and in-plane magnetic anisotropies are of great technological interest for microwave and spin wave-assisted magnetization switching. [Co/Pt] multilayers are well-known perpendicular anisotropy materials that have the potential to pin the magnetization of a soft magnetic layer, such as permalloy (Py), that has in-plane anisotropy, thereby forming a magnetic exchange spring. Here we report on multilayered [Co/Pt]/Pt/Py films, where an additional ultrathin Pt spacer has been included to control the coupling between the sub-units with in-plane and perpendicular magnetic anisotropy. Vector network analyser (VNA)-ferromagnetic resonance (FMR) measurements were made to obtain a complete picture of the resonant conditions, while the dynamical response of the sub-units was probed by synchrotron-based element- and phase selective x-ray detected FMR (XFMR). For all samples, only slight pinning of the dynamic magnetization of the Py by the [Co/Pt] was noted, and the FMR results were dominated by the 50 nm thick Py layer. Out-of-plane VNA-FMR maps reveal the presence of additional modes, e.g. a perpendicular standing spin-wave (PSSW) state. However, as the magnetic field is reduced below the saturation field, the PSSW state morphs continuously through a series of canted standing spin-wave (CSSW) states into a horizontal standing spin-wave (HSSW) state. The PSSW, CSSW and HSSW states are well described using a multilayer model of the Py film. The observation of CSSW modes is of particular relevance to microwave assisted magnetic recording, where microwave excitation stimulates precession of a soft layer canted out of plane by a pulsed magnetic field.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Plasmon spectroscopy for the determination of Ti 3 C 2 T x MXene few layer stacks architecture

Like many 2D materials, numerous properties of MXene multilayers, and especially the most popular one Ti 3 C 2 T x , have been shown to significantly depend on their architecture, i.e. the number of layers and interlayer distance. These structural parameters are thus key elements to be characterized for the analysis of MXene properties. Focusing on valence electron energy-loss spectroscopy (VEELS) as performed in a transmission electron microscope (TEM), and using density functional theory (DFT) simulations, we here analyze the layer dependent large changes in the VEEL spectra of Ti 3 C 2 T x multilayers as a probe of their total thickness, and emphasize the bulk plasmon energy sensitivity to interlayer distance. Together these findings allow to directly quantify the absolute number of layers in a Ti 3 C 2 T x stack up to ~10 nm thickness and give access to interlayer distance modifications with sub-angström sensitivity, evidencing VEELS as a powerful method for the characterization of MXene multilayers on the nanometer scale. We expect these results to be relevant for the study of structure/properties correlations in this class of materials, especially with the development of in situ or environmental TEM experiments.

Materials Science↗
DOE OSTI2019

Bias current dependence of superconducting transition temperature in superconducting spin-valve nanowires

Competition between superconducting and ferromagnetic ordering at interfaces between ferromagnets (F) and superconductors (S) gives rise to several proximity effects such as odd-triplet superconductivity and spin-polarized supercurrents. A prominent example of an S/F proximity effect is the spin switch effect (SSE) observed in S/F/N/F superconducting spin-valve multilayers, in which the superconducting transition temperature T c is controlled by the angle $\phi$ between the magnetic moments of the F layers separated by a nonmagnetic metallic spacer N. Here we present an experimental study of SSE in Nb/Co/Cu/Co/CoO x nanowires measured as a function of bias current flowing in the plane of the layers. In this work, these measurements reveal an unexpected dependence of T c ($\phi$) on the bias current: T c (π)–T c (0) changes sign with increasing current bias. We attribute the origin of this bias dependence of the SSE to a spin Hall current flowing perpendicular to the plane of the multilayer, which suppresses T c of the multilayer. The bias dependence of SSE can be important for hybrid F/S devices such as those used in cryogenic memory for superconducting computers as device dimensions are scaled down to the nanometer length scale.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Depth-resolved resonant inelastic x-ray scattering at a superconductor/half-metallic-ferromagnet interface through standing wave excitation

We demonstrate that combining standing wave (SW) excitation with resonant inelastic x-ray scattering (RIXS) can lead to depth resolution and interface sensitivity for studying orbital and magnetic excitations in correlated oxide heterostructures. SW-RIXS has been applied to multilayer heterostructures consisting of a superconductor La 1.85 Sr 0.15 CuO 4 (LSCO) and a half-metallic ferromagnet La 0.67 Sr 0.33 MnO 3 (LSMO). Easily observable SW effects on the RIXS excitations were found in these LSCO/LSMO multilayers. In addition, we observe different depth distribution of the RIXS excitations. Here, the magnetic excitations are found to arise from the LSCO/LSMO interfaces, and there is also a suggestion that one of the dd excitations comes from the interfaces. SW-RIXS measurements of correlated-oxide and other multilayer heterostructures should provide unique layer-resolved insights concerning their orbital and magnetic excitations, as well as a challenge for RIXS theory to specifically deal with interface effects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Prospects for the expansion of standing wave ambient pressure photoemission spectroscopy to reactions at elevated temperatures

Standing wave ambient pressure photoemission spectroscopy (SWAPPS) is a promising method to investigate chemical and potential gradients across solid-vapor and solid-liquid interfaces under close-to-realistic environmental conditions, far away from high vacuum. Until now, these investigations have been performed only near room temperature, but for a wide range of interfacial processes, chief among them being heterogeneous catalysis, measurements at elevated temperatures are required. One concern in these investigations is the temperature stability of the multilayer mirrors, which generate the standing wave field. At elevated temperatures, degradation of the multilayer mirror due to, for example, interdiffusion between the adjacent layers, decreases the modulation of the standing wave field, thus rendering SWAPPS experiments much harder to perform. Here, we show that multilayer mirrors consisting of alternate B4C and W layers are stable at temperatures exceeding 600 °C and are, thus, promising candidates for future studies of surface and subsurface species in heterogeneous catalytic reactions using SWAPPS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗