Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase 1 Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

Structure and plasticity in hot deformed FeAl intermetallic phase base alloy

This paper constitutes part of research conducted on the possibility of forming alloys based on intermetallic phases from the Fe-Al system via thermoplastic processing. Insufficient plasticity, which is an inhibitor of further development of these intermetallics as construction materials, makes the range of their applications limited. In the paper, an analysis is conducted of the influence of deformation parameters on the structure of an alloy of Fe-Al with the B2 type structure. Axi-symmetric compression tests were carried out at temperatures ranging from 600 deg. C to 1200 deg. C and at a deformation rate from 0.001 s{sup 1} to 10 s{sup -1}. Structural examination was carried out using light microscopy and transmission electron microscopy. A quantitative evaluation of the structure was made with the use of 'Met-Ilo'. The results obtained will be used for the development of mathematical models determining the influence of deformation parameters on the alloy structure.

36 MATERIALS SCIENCE↗

Synthesis of TiO{sub 2} thin films using single molecular precursors by MOCVD method for dye-sensitized solar cells application and study on film growth mechanism

For dye-sensitized solar cells application, in this study, we have synthesized TiO{sub 2} thin films at deposition temperature in the range of 300–750 °C by metalorganic chemical vapor deposition (MOCVD) method. Titanium(IV) isopropoxide, (TIP, Ti(O{sup i}Pr){sub 4}) and Bis(dimethylamido)titanium diisopropoxide, (BTDIP, (Me{sub 2}N){sub 2}Ti(O{sup i}Pr){sub 2}) were used as single source precursors that contain Ti and O atoms in the same molecule, respectively. Crack-free, highly oriented TiO{sub 2} polycrystalline thin films with anatase phase were deposited on Si(1 0 0) with TIP at temperature as low as 450 °C. XRD and TED data showed that below 500 °C, the TiO{sub 2} thin films were dominantly grown in the [2 1 1] direction on Si(1 0 0), whereas with increasing the deposition temperature to 700 °C, the main film growth direction was changed to [2 0 0]. Above 700 °C, however, rutile phase TiO{sub 2} thin films have only been obtained. In the case of BTDIP, on the other hand, only amorphous film was grown on Si(1 0 0) below 450 °C while a highly oriented anatase TiO{sub 2} film in the [2 0 0] direction was obtained at 500 °C. With further increasing deposition temperatures over 600 °C, the main film growth direction shows a sequential change from rutile [1 0 1] to rutile [4 0 0], indicating a possibility of getting single crystalline TiO{sub 2} film with rutile phase. This means that the precursor together with deposition temperature can be one of important parameters to influence film growth direction, crystallinity as well as crystal structure. To investigate the CVD mechanism of both precursors in detail, temperature dependence of growth rate was also carried out, and we then obtained different activation energy of deposition to be 77.9 and 55.4 kJ/mol for TIP and BTDIP, respectively. Also, we are tested some TiO{sub 2} film synthesized with BTDIP precursor to apply dye-sensitized solar cell.

36 MATERIALS SCIENCE↗

Exploring the influence of iron substitution in lithium rich layered oxides Li 2 Ru 1– x Fe x O 3 : triggering the anionic redox reaction

Lithium rich layered materials are an interesting class of materials which exploit both anionic and cationic redox reactions to store energy upwards of 250 mA h g –1 . This paper aims to understand the nature of the redox reactions taking place in these compounds. Li 2 RuO 3 was used as the base compound, which is then compared with compounds generated by partially substituting Ru with Ti and Fe respectively. Electrochemical tests indicate that Fe substitution in the sample leads to an improvement in capacity, cycle life and reduction of potential decay. To elucidate the reason for this improvement in operando diffraction experiments were carried out, highlighting the formation of a secondary de-lithiated phase. The distortion of the pristine structure eventually induces frontier orbital reorganization leading to the oxygen redox reaction resulting in extra capacity. Local changes at Fe and Ru ions are recorded using in operando X-ray absorption spectroscopy (XAS). It was noted that while Ru undergoes a reversible redox reaction, Fe undergoes a significant irreversible change in its coordination environment during cycling. In conclusion, the changes in the coordination environment of oxygen and formation of O 2 n– type species were probed in situ using soft X-rays.

36 MATERIALS SCIENCE↗

High-frequency fluctuation measurements by far-infrared laser Faraday-effect polarimetry-interferometry and forward scattering system on MST

Magnetic fluctuation-induced transport driven by global tearing modes has been measured by Faraday-effect polarimetry and interferometry (phase measurements) in the MST reversed field pinch. However, the role of small-scale broadband magnetic and density turbulence in transport remains unknown. In order to investigate broadband magnetic turbulence, we plan to upgrade the existing detector system by using planar-diode fundamental waveguide mixers optimized for high sensitivity. Initial tests indicate these mixers have ×10 sensitivity improvement compared to currently employed corner-cube Schottky-diode mixers and ×5 lower noise. Compact mixer design will allow us to resolve the wavenumbers up to k ∼ 1–2 cm{sup −1} for beam width w = 1.5 cm and 15 cm{sup −1} for beam width w = 2 mm. The system can also be used to measure the scattered signal (amplitude measurement) induced by both plasma density and magnetic fluctuations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Non-Condon nonequilibrium Fermi’s golden rule rates from the linearized semiclassical method

The nonequilibrium Fermi’s golden rule describes the transition between a photoexcited bright donor electronic state and a dark acceptor electronic state, when the nuclear degrees of freedom start out in a nonequilibrium state. In a previous paper [X. Sun and E. Geva, J. Chem. Theory Comput. 12, 2926 (2016)], we proposed a new expression for the nonequilibrium Fermi’s golden rule within the framework of the linearized semiclassical approximation and based on the Condon approximation, according to which the electronic coupling between donor and acceptor is assumed constant. In this paper we propose a more general expression, which is applicable to the case of non-Condon electronic coupling. We test the accuracy of the new non-Condon nonequilibrium Fermi’s golden rule linearized semiclassical expression on a model where the donor and acceptor potential energy surfaces are parabolic and identical except for shifts in the equilibrium energy and geometry, and the coupling between them is linear in the nuclear coordinates. Since non-Condon effects may or may not give rise to conical intersections, both possibilities are examined by considering the following: (1) A modified Garg-Onuchic-Ambegaokar model for charge transfer in the condensed phase, where the donor-acceptor coupling is linear in the primary-mode coordinate, and for which non-Condon effects do not give rise to a conical intersection; (2) the linear vibronic coupling model for electronic transitions in gas phase molecules, where non-Condon effects give rise to conical intersections. We also present a comprehensive comparison between the linearized semiclassical expression and a progression of more approximate expressions, in both normal and inverted regions, and over a wide range of initial nonequilibrium states, temperatures, and frictions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

THE SCHMIDT-KENNICUTT LAW OF MATCHED-AGE STAR-FORMING REGIONS; Pa{alpha} OBSERVATIONS OF THE EARLY-PHASE INTERACTING GALAXY TAFFY I

In order to test a recent hypothesis that the dispersion in the Schmidt-Kennicutt law arises from variations in the evolutionary stage of star-forming molecular clouds, we compared molecular gas and recent star formation in an early-phase merger galaxy pair, Taffy I (UGC 12915/UGC 12914, VV 254) which went through a direct collision 20 Myr ago and whose star-forming regions are expected to have similar ages. Narrowband Pa{alpha} image is obtained using the ANIR near-infrared camera on the mini-TAO 1 m telescope. The image enables us to derive accurate star formation rates within the galaxy directly. The total star formation rate, 22.2 M{sub Sun} yr{sup -1}, was found to be much higher than previous estimates. Ages of individual star-forming blobs estimated from equivalent widths indicate that most star-forming regions are {approx}7 Myr old, except for a giant H II region at the bridge which is much younger. Comparison between star formation rates and molecular gas masses for the regions with the same age exhibits a surprisingly tight correlation, a slope of unity, and star formation efficiencies comparable to those of starburst galaxies. These results suggest that Taffy I has just evolved into a starburst system after the collision, and the star-forming sites are at a similar stage in their evolution from natal molecular clouds except for the bridge region. The tight Schmidt-Kennicutt law supports the scenario that dispersion in the star formation law is in large part due to differences in evolutionary stage of star-forming regions.

79 ASTRONOMY AND ASTROPHYSICS↗

Metal-poor, strongly star-forming galaxies in the DEEP2 Survey: The relationship between stellar mass, temperature-based metallicity, and star formation rate

We report on the discovery of 28 z≈0.8 metal-poor galaxies in DEEP2. These galaxies were selected for their detection of the weak [O iii] λ4363 emission line, which provides a “direct” measure of the gas-phase metallicity. A primary goal for identifying these rare galaxies is to examine whether the fundamental metallicity relation (FMR) between stellar mass, gas metallicity, and star formation rate (SFR) holds for low stellar mass and high SFR galaxies. The FMR suggests that higher SFR galaxies have lower metallicity (at fixed stellar mass). To test this trend, we combine spectroscopic measurements of metallicity and dust-corrected SFR with stellar mass estimates from modeling the optical photometry. We find that these galaxies are 1.05 ± 0.61 dex above the z∼1 stellar mass–SFR relation and 0.23 ± 0.23 dex below the local mass–metallicity relation. Relative to the FMR, the latter offset is reduced to 0.01 dex, but significant dispersion remains (0.29 dex with 0.16 dex due to measurement uncertainties). This dispersion suggests that gas accretion, star formation, and chemical enrichment have not reached equilibrium in these galaxies. This is evident by their short stellar mass doubling timescale of ≈100{sub −75}{sup +310} Myr, which suggests stochastic star formation. Combining our sample with other z∼1 metal-poor galaxies, we find a weak positive SFR–metallicity dependence (at fixed stellar mass) that is significant at 94.4% confidence. We interpret this positive correlation as recent star formation that has enriched the gas but has not had time to drive the metal-enriched gas out with feedback mechanisms.

79 ASTRONOMY AND ASTROPHYSICS↗

Millicharged scalar fields, massive photons and the breaking of S U ( 3 ) C × U ( 1 ) EM

Under the assumption that the current epoch of the Universe is not special, i.e., is not the final state of a long history of processes in particle physics, the cosmological fate of SU (3) C × U (1) EM is investigated. Spontaneous symmetry breaking of U (1) EM at the temperature of the Universe today is carried out. The charged scalar field Φ EM which breaks the symmetry is found to be ruled out for the charge of the electron, q = e . Scalar fields with millicharges are viable and limits on their masses and charges are found to be q ≲ 10 –3 e and m ΦEM ≲ 10 –5 eV. Furthermore, it is possible that U (1) EM has already been broken at temperatures higher than T = 2.7 K given the nonzero limits on the mass of the photon. A photon mass of m γ = 10 –18 eV, the current upper limit, is found to require a spontaneous symmetry breaking scalar mass of m ΦEM ~ 10 –13 eV with charge q = 10 –6 e, well within the allowed parameter space of the model. Finally, the cosmological fate of the strong interaction is studied. SU (3) C is tested for complementarity in which the confinement phase of QCD + colored scalars is equivalent to a spontaneously broken SU (3) gauge theory. If complementarity is not applicable, SU (3) C has multiple symmetry breaking paths with various final symmetry structures. The stability of the colored vacuum at finite temperature in this scenario is nonperturbative and a definitive statement on the fate of SU (3) C is left open. Cosmological implications for the metastability of the vacua—electromagnetic, color, and electroweak—are discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Methods for Quantitative Thermal Analysis of Lithium Solid-State and Beyond Battery Safety

The use of differential scanning calorimetry (DSC) to measure the thermal behavior of individual components and electrolyte/electrode combinations is common. However, here we focus on DSC tests on an anode, cathode, and electrolyte (ACE) component combination over a temperature range that includes many of the phase transitions and key reactions (i.e., to 500 °C) that contribute to thermal runaway. This method can help quantify the complex reaction network in a full cell, thereby informing potential safety issues. Here, we used DSC heat flow data from a solid-state Li 0.43 CoO 2 +C+PVDF | LLZO | Li metal ACE sample and its components to quantify key factors affecting results. We focused on three areas: (1) ACE sample preparation and assembly in DSC pans, (2) DSC measurement parameters, and (3) heat flow analysis. Key points include the choice of component ratios (e.g., commercially relevant N:P capacity ratio), the importance of conductive carbon and binder, type of pan used, DSC ramp rate, and integration method used when dealing with broad and overlapping exothermic peaks. This work deepens the scientific basis and best practices for obtaining heat flow data from ACE samples for early-stage evaluation of solid-state and beyond battery safety.

25 ENERGY STORAGE↗

Office of FreedomCAR & Vehicle Technologies

High-level objective of this project is to develop nanoparticle based additive technology to improve friction and wear characteristics of engine oil with a long-term focus to enhance durability and efficiency of engines. The project encompasses a detailed investigation of various chemicals that favors stable boundary film formation and therefore reduce friction and wear of engine components. These active chemicals designed as nanomaterials will be surface-stabilized to gain maximum dispersion stability in a lubricant media. This effort shall be focused with the following objectives in mind: develop active nanoparticle composite, optimize process design, detailed tribological testing and surface characterization, physical and chemical characterization of nanomaterials, and limited component level testing to document friction and wear improvements. Additional motivation is to minimize sulfur/phosphorous contents and lower ash forming components in additives and therefore improve aftertreatment functioning and emission. This effort shall be focused, over a two year funding period: Phase-I will be primarily a feasibility study, which includes selection of components for active nanoparticles, design and formulation, and synthesis of the active nanoparticles, optimize process design, physical and chemical characterization of nanomaterials, tribological testing and document friction and wear improvements. As a continuous effort of the Phase-I, Phase-II will focus on the optimization of the identified nanoparticle-based additives specifically for DOE strategic goal - minimizing S and P contents in additives and lowering ash-forming components. Additional efforts will also be invested in extended component level tribo-testing, manufacturing process scale-up, cost evaluation, and commercial viability assessment. In boundary lubrication, mating surfaces in direct physical contact are in surface asperities dimensional scale. These conditions may benefit from the nanometric size of the advanced nanoparticle lubricants in the following ways: (1) by supplying nano to sub-micron size lubricating agents which reduce friction and wear at the asperity contact zone, (2) by enabling strong metal adsorption and easy wetting, (3) by reacting with the surface to form durable lubricating 'transient transfer' films, sustain high loads and also retain under high temperatures, and (4) by enabling all these at minimal cost and great environmental safety. Suitably designed nanomaterials can significantly lower sulfur and phosphorus level in the lubricant additive pack, and therefore positively impact after-treatment catalyst life and exhaust emissions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Battery Electric Vehicle Eco-Cooperative Adaptive Cruise Control in the Vicinity of Signalized Intersections

This study develops a connected eco-driving controller for battery electric vehicles (BEVs), the BEV Eco-Cooperative Adaptive Cruise Control at Intersections (Eco-CACC-I). The developed controller can assist BEVs while traversing signalized intersections with minimal energy consumption. The calculation of the optimal vehicle trajectory is formulated as an optimization problem under the constraints of (1) vehicle acceleration/deceleration behavior, defined by a vehicle dynamics model; (2) vehicle energy consumption behavior, defined by a BEV energy consumption model; and (3) the relationship between vehicle speed, location, and signal timing, defined by vehicle characteristics and signal phase and timing (SPaT) data shared under a connected vehicle environment. The optimal speed trajectory is computed in real-time by the proposed BEV eco-CACC-I controller, so that a BEV can follow the optimal speed while negotiating a signalized intersection. The proposed BEV controller was tested in a case study to investigate its performance under various speed limits, roadway grades, and signal timings. In addition, a comparison of the optimal speed trajectories for BEVs and internal combustion engine vehicles (ICEVs) was conducted to investigate the impact of vehicle engine types on eco-driving solutions. Lastly, the proposed controller was implemented in microscopic traffic simulation software to test its networkwide performance. The test results from an arterial corridor with three signalized intersections demonstrate that the proposed controller can effectively reduce stop-and-go traffic in the vicinity of signalized intersections and that the BEV Eco-CACC-I controller produces average savings of 9.3% in energy consumption and 3.9% in vehicle delays.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

CLUMPY DISKS AS A TESTBED FOR FEEDBACK-REGULATED GALAXY FORMATION

We study the dependence of fragmentation in massive gas-rich galaxy disks at z >1 on stellar feedback schemes and hydrodynamical solvers, employing the GASOLINE2 SPH code and the lagrangian mesh-less code GIZMO in finite mass mode. Non-cosmological galaxy disk runs with the standard delayed-cooling blastwave feedback are compared with runs adopting a new superbubble feedback, which produces winds by modeling the detailed physics of supernova-driven bubbles and leads to efficient self-regulation of star formation. We find that, with blastwave feedback, massive star-forming clumps form in comparable number and with very similar masses in GASOLINE2 and GIZMO. Typical clump masses are in the range 10{sup 7}–10{sup 8} M {sub ⊙}, lower than in most previous works, while giant clumps with masses above 10{sup 9} M {sub ⊙} are exceedingly rare. By contrast, superbubble feedback does not produce massive star-forming bound clumps as galaxies never undergo a phase of violent disk instability. In this scheme, only sporadic, unbound star-forming overdensities lasting a few tens of Myr can arise, triggered by non-linear perturbations from massive satellite companions. We conclude that there is severe tension between explaining massive star-forming clumps observed at z >1 primarily as the result of disk fragmentation driven by gravitational instability and the prevailing view of feedback-regulated galaxy formation. The link between disk stability and star formation efficiency should thus be regarded as a key testing ground for galaxy formation theory.

79 ASTRONOMY AND ASTROPHYSICS↗

CTF_

CTF is a thermal-hydraulic simulation tool designed for modeling the reactor vessel region of light water reactors. The code is capable of modeling both coolant and solid regions and includes a nuclear fuel rod model. Coolant is represented with a 9-equation (two phases plus droplets and non-condensable gas) model with closure relationships being provided for normal and accident conditions. Meshing is done using the subchannel approach, which models the coolant region as a collection of parallel 1-D flow paths that communicate laterally through "gaps". CTF also includes a collection of supporting software tools that include: Xml2ctf - A utility for creating native CTF input decks from a simplified input file; pyCTF - A collection of Python utilities used for post-processing CTF results, manipulating CTF input models, and testing differences between output files; CTFFuel - A separate front-end to the CTF fuel rod solver package; Multistate - A separate driver for CTF that communicates through the code coupling interface; and veraAPI - A c++ interface to the code.

Salko, Robert K↗

Assessment of Pre-Irradiation SiC CMC Joint Performance in Representative Cladding Geometries

Silicon carbide fiber reinforced, silicon carbide matrix composites (SiC-SiC) offer strength at high temperatures, corrosion resistance, and stability during irradiation, and are being developed by General Atomics as cladding for accident tolerant fuel (ATF) applications and advanced reactor concepts. Advanced joining techniques capable of withstanding harsh reactor environments are key to enable GA’s SiGAtm SiC-SiC composite. The objective of this work is to obtain joint-specific material properties for assemblies in representative planar and cladding geometries that will allow for the generation of a material properties database and more accurate simulation of SiC joint behavior across arange of temperatures and irradiation conditions. To support this, three different joint formulations are being assessed for mechanical and thermal performance pre and post irradiation in the High Flux Isotope Reactor (HIFR) at ORNL. GA has previously identified its hybrid SiC (HSiC) joint as the most promising and best suited joining approach for cladding applications [1]. Additionally, oxide and transeutectic phase (TEP) joints are being investigated to make the material property database more comprehensive as these joints have previously shown strength resilience under irradiation in planar geometries [2]. The thermal and mechanical data obtained in this work will address vital knowledge gaps, enabling more accurate modeling of joints in SiC-based components for accelerated material qualification.The scope of work presented here focuses on the mechanical and thermal performance of the joint material prior to irradiation in HFIR. Endplug push-out (EPPO) testing to determine joint strength in tube geometries, and shear strength testing for planar geometries have provided a benchmark for pre-irradiation mechanical performance. These results show that all three selected joint methodologies result in cladding joints capable of withstanding the expected joint stresses in a LWR reactor environment [3]. This has been accompanied by He leak testing of the joint regions on tube specimens to assess the suitability of each joint methodology for cladding applications. Here, only the HSiC formulation consistently met critical leak rate requirements suggesting that other joining strategies require additional development. Finally, pre-irradiation thermal testing has been completed to establish a baseline for comparison after irradiation. Subsequent irradiation of these joints types in HFIR will provide further detail on joint material properties and their appropriateness for nuclear applications.

Gonderman, Sean↗

High Quality, Low Cost Bulk Gallium Nitride Substrates Grown by the Electrochemical Solution Growth Method

The objective of this project was to develop the Electrochemical Solution Growth (ESG) method conceived / patented at Sandia National Laboratory into a commercially viable bulk gallium nitride (GaN) growth process that can be scaled to low cost, high quality, and large area GaN wafer substrate manufacturing. The goal was to advance the ESG growth technology by demonstrating rotating seed growth at the lab scale and then transitioning process to prototype commercial system, while validating the GaN material and electronic / optical device quality. The desired outcome of the project is a prototype commercial process for US-based manufacturing of high quality, large area, and lower cost GaN substrates that can drive widespread deployment of energy efficient GaN-based power electronic and optical devices. In year 1 of the project (Sept 2012 – Dec 2013) the overall objective was to demonstrate crystalline GaN growth > 100um on a GaN seed crystal. The development plan included tasks to demonstrate and implement a method for purifying reagent grade salts, develop the reactor 1 process for rotating seed Electrochemical Solution Growth (ESG) of GaN, grow and characterize ESG GaN films, develop a fluid flow and reaction chemistry model for GaN film growth, and design / build an improved growth reactor capable of scaling to 50mm seed diameter. The first year’s project objectives were met in some task areas including salt purification, film characterization, modeling, and reactor 2 design / fabrication. However, the key project objective of the growth of a crystalline GaN film on the seed template was not achieved. Amorphous film growth on the order of a few tenths of a micron has been detected with a film composition including Ga and N, plus several other impurities originating from the process solution and hardware. The presence of these impurities, particularly the oxygen, has inhibited the demonstration of crystalline GaN film growth on the seed template. However, the presence of both Ga and N at the growth surface indicates that the reactor hardware physics is all functioning properly; achieving film growth is a matter of controlling the chemistry at the interface. The impurities originating from the hardware are expected to be straightforward to eliminate. Activities were defined for an extension of budget period 1 to eliminate the undesired impurities originating from the reactor hardware and interfering with crystalline GaN film growth. The budget period 1 extension was negotiated during the 1st half of 2014. The budget period 1 extension spanned approximately from August 2014 to August 2015. The project objective for this extension period was to demonstrate at least 0.5um crystalline GaN film on a GaN seed in the lab scale reactor. The focus of the budget 1 extension period from August 2014 to August 2015 was to eliminate oxygen contamination interference with GaN film growth. The team procured the highest purity lowest oxygen salt for testing. Low oxygen crucible materials such as silicon carbide were installed and evaluated in the laboratory reactor. Growth experiments were performed with high purity salt, high purity hardware, and optimized oxide removal from the seed surface. Experiments were characterized with methods including UV inspection, profilometry, x-ray diffraction (XRD) to determine crystalline structure, optical and scanning electron microscopy, photoluminescence, x-ray photon spectroscopy (XPS), transmission electron microscopy (TEM), and secondary ion mass spectroscopy (SIMS). Despite successfully integrating the low oxygen materials in the laboratory reactor, the goal of depositing 0.5um of crystalline GaN on the MOCVD GaN seed was not met. Very thin (ca. 10nm) cubic phase GaN deposition was observed on the hexagonal MOCVD GaN seeds. But there was a competing etching reaction which was also observed and thought to be related to the presence of metallic lithium, a byproduct of the LiCl-KCl salt used as the process medium. The etching reaction could potentially be addressed by alternate salts not containing lithium, but would necessitate starting all over on the reactor and process design. Further, controlling the reaction of Ga and N in the bulk salt to favor deposition on the seed has proved to be very difficult and unlikely to be solved within the scope of this project in a manner consistent with the original objective for wafer or crystal scale thickness for GaN deposition on a GaN seed. Upon completion of the budget 1 extension period in August 2015 the project partners and DOE agreed to stop work on the project.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

The Evolution of Randomized Clinical Trial Designs to Assess Therapeutics in Alzheimer Disease

Importance The success of recent randomized clinical trials (RCTs) for Alzheimer disease (AD), particularly those focusing on anti-amyloid therapies, has been discussed at length. However, the evolution of RCT design features for AD that preceded this success remain underexplored. Objective To describe temporal changes in the features of RCT design for interventions in AD. Evidence Review PubMed, Scopus, and Web of Science databases were searched in January 2025 for phase 2 and 3 AD RCTs published between January 1992 and December 2024. RCTs that investigated an intervention for AD, with a placebo or standard-of-care control group, were included. Four assessors independently reviewed full-text articles to capture study characteristics. Main Outcomes and Measures The number of participants and the duration of RCTs as well as the target population, outcomes, and funding were extracted from published reports. These features were analyzed with respect to time using linear regression and χ 2 analyses. Results The study included 203 RCTs with 79 589 participants testing interventions in AD. From 1992 to 2024, the mean sample size increased by 464% for phase 2 RCTs (from 42 to 237), and 50% for phase 3 RCTs (from 632 to 951), while the mean trial duration increased by 188% (from 16 to 46 weeks) for phase 2, and 256% (from 20 to 71 weeks) for phase 3 RCTs. This longer duration of RCTs may be partially attributed by a greater share of disease-modifying rather than symptomatic treatments. Similarly, more recent trials required AD biomarker evidence for enrollment (from 1 of 36 [2.7%] before 2006 to 40 of 76 [52.6%] since 2019). A substantial difference in the type of therapeutics researched was observed, with anti-amyloid and anti-tau RCTs being more likely to be funded by the pharmaceutical industry compared with neurotransmitter or other RCTs (anti-amyloid or anti-tau, 68 of 71 [95.8%]; neurotransmitter, 52 of 69 [77.6%]; other, 33 of 52 [63.5%]). RCT transparency improved, with more frequent data accessibility statements, registered reports, and better reporting on race and ethnicity. Conclusions and Relevance This methodology research of AD RCTs highlights substantial changes in key features of AD clinical trials from 1992 to 2024. AD RCTs have become larger and longer, such that they are powered to detect smaller clinical differences. The increased sample sizes and duration should enable the detection of smaller and more slowly occurring outcomes, which may lead to successful RCTs of therapies with slower and more subtle efficacy.

General & Internal Medicine↗

Advancing technologies for lignin-based jet fuel production in aqueous phase

Integrating lignin into a cellulosic ethanol plant for the co-production of lignin-based jet fuel (LJF) in aqueous phase offers a significant opportunity to boost operational efficiency, economic viability, carbon conversion, and the overall sustainability of biofuel and chemical production. LJF is lignin-structure-based jet fuel blendstocks primarily composed of alkyl-substituted mono-, bi-, and tri-cyclohexanes. It exhibits high energy density, potential for low emissions, and favourable blend characteristics that comply with drop-in specifications. An overview of lignin feedstock, catalytic processes, LJF chemical compositions, fuel properties tests, and techno-economic analysis (TEA) and life cycle assessment (LCA) indicate that (1) the reactivity of lignin plays a crucial role in its structure transformation to LJF molecules; (2) catalytic processing of lignin to LJF can occur through a simultaneous depolymerization and hydrodeoxygenation process, bypassing the intermediate step of producing and upgrading lignin-derived oil; (3) LJF's uniqueness molecules making it more promising for high energy content and low emission jet fuel properties for next generation sustainable aviation fuel (SAF); and (4) TEA and LCA demonstrate that LJF is not only potentially cost-effective but also offers favourable carbon footprint compared to other SAFs. In conclusion, this review highlights the most recent advancements in LJF technology, along with the challenges and opportunities that lie ahead in fulfilling its potential.

09 BIOMASS FUELS↗

Diffusive mass transport in agglomerated glassy fallout from a near-surface nuclear test

Aerodynamically-shaped glassy fallout is formed when vapor phase constituents from the nuclear device are incorporated into molten carriers (i.e. fallout precursor materials derived from soil or other near-field environmental debris). The effects of speciation and diffusive transport of condensing constituents are not well defined in models of fallout formation. Previously we reported observations of diffuse micrometer scale layers enriched in Na, Fe, Ca, and 235 U, and depleted in Al and Ti, at the interfaces of agglomerated fallout objects. Here in this paper, we derive the timescales of uranium mass transport in such fallout as it cools from 2500 K to 1500 K by applying a 1-dimensional planar diffusion model to the observed 235 U/ 30 Si variation at the interfaces. By modeling the thermal transport between the fireball and the carrier materials, the time of mass transport is calculated to be <0.6 s, <1 s, <2 s, and <3.5 s for fireball yields of 0.1 kt, 1 kt, 10 kt, and 100 kt respectively. Based on the calculated times of mass transport, a maximum temperature of deposition of uranium onto the carrier material of ~2200 K is inferred (1σ uncertainty of ~200 K). We also determine that the occurrence of micrometer scale layers of material enriched in relatively volatile Na-species as well as more refractory Ca-species provides evidence for an oxygen-rich fireball based on the vapor pressure of the two species under oxidizing conditions. These results represent the first application of diffusion-based modeling to derive material transport, thermal environments, and oxidation-speciation in near-surface nuclear detonation environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗