SEARCH · Search NASA

Results for “Reductive Effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,279 records · Page 71

All sources NASA NTRS DOE OSTI

NASA NTRS1998

Effects of Tip Clearance and Casing Recess on Heat Transfer and Stage Efficiency in Axial Turbines

Calculations were performed to assess the effect of the tip leakage flow on the rate of heat transfer to blade, blade tip and casing. The effect on exit angle and efficiency was also examined. Passage geometries with and without casing recess were considered. The geometry and the flow conditions of the GE-E 3 first stage turbine, which represents a modem gas turbine blade were used for the analysis. Clearance heights of 0%, 1%, 1.5% and 3% of the passage height were considered. For the two largest clearance heights considered, different recess depths were studied. There was an increase in the thermal load on all the heat transfer surfaces considered due to enlargement of the clearance gap. Introduction of recessed casing resulted in a drop in the rate of heat transfer on the pressure side but the picture on the suction side was found to be more complex for the smaller tip clearance height considered. For the larger tip clearance height the effect of casing recess was an orderly reduction in the suction side heat transfer as the casing recess height was increased. There was a marked reduction of heat load and peak values on the blade tip upon introduction of casing recess, however only a small reduction was observed on the casing itself. It was reconfirmed that there is a linear relationship between the efficiency and the tip gap height. It was also observed that the recess casing has a small effect on the efficiency but can have a moderating effect on the flow underturning at smaller tip clearances.

Ameri, A. A.↗

NASA NTRS2023

Cryogenic Flow Boiling in Microgravity: Effects of Reduced Gravity on Two-Phase Fluid Physics and Heat Transfer

With the growing interest in space exploration, cryogenic technologies involving two-phase flow and heat transfer are in high demand to successfully procure advanced space applications such as fuel depots and nuclear thermal propulsion (NTP) systems for deep space missions. However, the unique and extreme thermal properties of cryogenic fluids introduce distinct flow boiling fluid physics and energy transport phenomena, which differ significantly from those observed with conventional fluids. Understanding the unique two-phase physics in cryogenic flow boiling remains an ongoing challenge. Furthermore, the lack of readily available microgravity cryogenic steady-state heat transfer data hinders the assessment of gravitational effects on cryogenic flow boiling. This study aims to elucidate the gravitational effects on two-phase fluid physics and heat transfer by conducting the first-ever experimental measurement of cryogenic flow boiling performance using a steady-state heated method in a reduced gravity environment. Parabolic flight experiments were performed to acquire both heat transfer measurements and high-speed video of interfacial behaviors, under varying gravity levels (microgravity, hypergravity, Lunar gravity, and Martian gravity). The experiments involved flow boiling of liquid nitrogen (LN 2 ) with a near-saturated inlet along a circular heated tube of dimensions 8.5-mm inner diameter and 680-mm heated length. The operating parameters varied are mass velocity of 398.3 - 1342.8 kg/m2s, inlet quality of -0.08 to -0.01, and inlet pressure of 413.68 - 689.48 kPa. Captured microgravity flow patterns range from bubbly to annular, all having vapor structures that are larger than those under higher gravity levels. Under microgravity, absence of buoyancy yields symmetrical vapor structures without flow stratification, laying a physical foundation for the distinct two-phase heat transfer trends during LN 2 flow boiling in microgravity. Transient data collected during the flight parabolas exhibited decreasing heated wall temperature as the aircraft transitioned from hypergravity to microgravity phases. The temperature variation indicated an enhancement in flow boiling heat transfer with decreasing gravity levels and a reduction with increasing gravity levels. The effect of reduced gravity on cryogenic flow boiling heat transfer coefficient (HTC) is discussed based on steady state heat transfer analysis. Seminal HTC correlations are evaluated against the measured microgravity HTC data, of which one is identified for superior accuracy in predicting microgravity data. Finally, a new HTC correlation is proposed to improve accuracy of microgravity predictions, yet there still exists room for further improvement with future terrestrial flow boiling experiments at different flow orientations relative to Earth gravity.

Microgravity↗

DOE OSTI2026

Calculation of monomer yields, verification of PG concentration approximation, catalyst comparison for neat aromatic RCF, SEM micrographs for postreaction pulps, yields of aqueous-phase sugar derivatives after PG-H2O RCF, reactor pressure transients, GPC comparing pre- and postreaction organic solvent composition, PG-H2O miscibility testing, GPC probing dimer/oligomer fractionation in PG-H2O mixtures for

Reductive catalytic fractionation (RCF) is an effective lignin-first biorefining method to extract lignin as a stabilized oil from lignocellulosic biomass. To realize RCF at scale, process modeling has shown that minimizing the use of exogenous organic solvents is critical. To this end, here we investigate the ability of lignin-derived monomers to act as either solvents or cosolvents for RCF. We begin by examining the influence of lignin-derived aromatic compounds (4-propylguaiacol, 4-propylphenol, and propylbenzene) on RCF monomer yields and subsequently extend our analysis to mixtures of 4-propylguaiacol and either methanol or water. We demonstrate that 4-propylguaiacol is an effective solvent for lignin extraction and depolymerization during RCF, especially when used in combination with water as a cosolvent. Cosolvent mixtures of 4-propylguaiacol and water enable up to 81% lignin extraction, monomer yields up to 25 wt %, and postreaction phase separation. However, unlike methanol, water as a cosolvent fails to inhibit aromatic ring hydrogenation when conducted over Ru/C as a catalyst, potentially leading to excess hydrogen consumption in a process utilizing this approach. Nonetheless, these results suggest a promising strategy for eliminating external organic solvents from RCF by utilizing mixtures of lignin-derived compounds and water as alternative extraction solvents.

biorefining↗

DOE OSTI2022

Indices of extremes: geographic patterns of change in extremes and associated vegetation impacts under climate intervention

Extreme weather events have been demonstrated to be increasing in frequency and intensity across the globe and are anticipated to increase further with projected changes in climate. Solar climate intervention strategies, specifically stratospheric aerosol injection (SAI), have the potential to minimize some of the impacts of a changing climate while more robust reductions in greenhouse gas emissions take effect. However, to date little attention has been paid to the possible responses of extreme weather and climate events under climate intervention scenarios. We present an analysis of 16 extreme surface temperature and precipitation indices, as well as associated vegetation responses, applied to the Geoengineering Large Ensemble (GLENS). GLENS is an ensemble of simulations performed with the Community Earth System Model (CESM1) wherein SAI is simulated to offset the warming produced by a high-emission scenario throughout the 21st century, maintaining surface temperatures at 2020 levels. GLENS is generally successful at maintaining global mean temperature near 2020 levels; however, it does not completely offset some of the projected warming in northern latitudes. Some regions are also projected to cool substantially in comparison to the present day, with the greatest decreases in daytime temperatures. The differential warming–cooling also translates to fewer very hot days but more very hot nights during the summer and fewer very cold days or nights compared to the current day. Extreme precipitation patterns, for the most part, are projected to reduce in intensity in areas that are wet in the current climate and increase in intensity in dry areas. We also find that the distribution of daily precipitation becomes more consistent with more days with light rain and fewer very intense events than currently occur. In many regions there is a reduction in the persistence of long dry and wet spells compared to present day. However, asymmetry in the night and day temperatures, together with changes in cloud cover and vegetative responses, could exacerbate drying in regions that are already sensitive to drought. Overall, our results suggest that while SAI may ameliorate some of the extreme weather hazards produced by global warming, it would also present some significant differences in the distribution of climate extremes compared to the present day.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Activation of Transition Metal (Fe, Co and Ni)-Oxide Nanoclusters by Nitrogen Defects in Carbon Nanotube for Selective CO 2 Reduction Reaction

The electrochemical carbon dioxide reduction reaction (CO2RR), which can produce value-added chemical feedstocks, is a proton-coupled-electron process with sluggish kinetics. Thus, highly efficient, cheap catalysts are urgently required. Transition metal oxides such as CoO x , FeO x , and NiO x are low-cost, low toxicity, and abundant materials for a wide range of electrochemical reactions, but are almost inert for CO 2 RR. Here, we report for the first time that nitrogen doped carbon nanotubes (N-CNT) have a surprising activation effect on the activity and selectivity of transition metal-oxide (MO x where M = Fe, Ni, and Co) nanoclusters for CO 2 RR. MO x supported on N-CNT, MOx/N-CNT, achieves a CO yield of 2.6–2.8 mmol cm -2 min -1 at an overpotential of -0.55V, which is two orders of magnitude higher than MO x supported on acid treated CNTs (MOx/O-CNT) and four times higher than pristine N-CNT. The faraday efficiency for electrochemical CO 2 -to-CO conversion is as high as 90.3% at overpotential of 0.44V. Both in-situ XAS measurements and DFT calculations disclose that MO x nanoclusters can be hydrated in CO 2 saturated KHCO 3 , and the N defects of N-CNT effectively stabilize these metal hydroxyl species under carbon dioxide reduction reaction conditions, which can split the water molecules and provide local protons to inhibit the poisoning of active sites under carbon dioxide reduction reaction conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Effect of bimetallic modification on blast furnace slag and its application in low‐temperature selective catalytic reduction

Abstract Objective In order to control NO x in low‐temperature flue gases emitted from non‐power industries and to reduce the preparation cost of denitration catalysts, this study uses inexpensive blast furnace slag as raw material to prepare denitration catalysts. Methods After cooling, drying and grinding, the blast furnace slag becomes a powder with considerable fineness and meets the requirements of activity index, which is called GGBS (ground granulated blast furnace slag). Using GGBS as denitration catalyst carrier, the active components M (M = Fe, Co, Ni, Cu and Ce) are loaded on Mn‐based GGBS catalyst using an impregnation method. Conclusions The effect of different active components on the denitration performance and sulfur resistance of Mn‐based GGBS catalysts is investigated. The results show that the Mn‐Ce/GGBS catalyst has better denitration performance and sulfur resistance. The Mn‐Ce/GGBS catalyst has a significant denitration performance when load ratio is 2:1. The active component Ce improves the denitration performance of the catalyst, reduces sulfur poisoning and extends the life of the catalyst. The SO 2 in the flue gas increases the acid sites on the catalyst surface and improves catalyst activity. The larger the ratios of Mn 4+ /Mn 3+ , Ce 4+ /Ce 3+ and O α /O β , the stronger the catalyst activity and the better the denitration performance. © 2022 Society of Chemical Industry (SCI).

Zhang, Lei↗

NASA NTRS1993

Training high performance skills using above real-time training

The Above Real-Time Training (ARTT) concept is a unique approach to training high performance skills. ARTT refers to a training paradigm that places the operator in a simulated environment that functions at faster than normal time. Such a training paradigm represents a departure from the intuitive, but not often supported, feeling that the best practice is determined by the training environment with the highest fidelity. This approach is hypothesized to provide greater 'transfer value' per simulation trial, by incorporating training techniques and instructional features into the simulator. These techniques allow individuals to acquire these critical skills faster and with greater retention. ARTT also allows an individual trained in 'fast time' to operate at what appears to be a more confident state, when the same task is performed in a real-time environment. Two related experiments are discussed. The findings appear to be consistent with previous findings that show positive effects of task variation during training. Moreover, ARTT has merit in improving or maintaining transfer with sharp reductions in training time. There are indications that the effectiveness of ARTT varies as a function of task content and possibly task difficulty. Other implications for ARTT are discussed along with future research directions.

Guckenberger, Dutch↗

NASA NTRS2015

Small Scale Mass Flow Plug Calibration

A simple control volume model has been developed to calculate the discharge coefficient through a mass flow plug (MFP) and validated with a calibration experiment. The maximum error of the model in the operating region of the MFP is 0.54%. The model uses the MFP geometry and operating pressure and temperature to couple continuity, momentum, energy, an equation of state, and wall shear. Effects of boundary layer growth and the reduction in cross-sectional flow area are calculated using an in- integral method. A CFD calibration is shown to be of lower accuracy with a maximum error of 1.35%, and slower by a factor of 100. Effects of total pressure distortion are taken into account in the experiment. Distortion creates a loss in flow rate and can be characterized by two different distortion descriptors.

mass-flow measurements↗

NASA NTRS1959

Effect on Inlet Performance of a Cowl Visor and an Internal-Contraction Cowl for Drag Reduction at Mach Numbers 3.07 and 1.89

Two methods for reducing the external cowl angle, and hence the cowl pressure drag, were investigated on a two-dimensional model. One method used at both on- and off-design Mach numbers was the addition of a cowl visor that had the inner surface parallel to the free stream at 0 deg angle of attack. The other method investigated consisted in replacing the original cowl by a flatter cowl that also provided internal contraction. Both the visor and the internal-contraction cowl reduced the cowl pressure drag 64 percent or more. The visor had little effect on inlet performance at the design Mach number except to reduce the stability range slightly. At off-design, the visor caused an increase in critical pressure recovery.

Gertsma, Laurence W.↗

DOE OSTI2021

SPRUCE Warming Promotes the Use of Organic Matter as an Electron Acceptor in a Peatland: Supporting Data

These data are provided in support of the publication: Warming Promotes the Use of Organic Matter as an Electron Acceptor in a Peatland (Rush et al., 2021). Rush et al. (2021) reported on the effect of temperature on microbial organic matter reduction at the SPRUCE study site and S1 bog. Specifically, electron shuttling capacity (ESC), CH4 production, CO2 production, and acetate concentration were measured to explore both direct and indirect (through changes in soil quality and water-table level) effects of warming on microbial activity. Samples were collected in the summer of 2016 and 2017 depending on the experiment. This dataset contains five files in comma separated (*.csv) format. The SPRUCE Experiment Site is located in a Picea mariana [black spruce] Sphagnum spp. bog forest in northern Minnesota, 40 km north of Grand Rapids, in the USDA Forest Service Marcell Experimental Forest (MEF). This ecosystem, which is located at the southern margin of the boreal forest, is considered especially vulnerable to climate change and anticipated to be near its tipping point.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1989

Reduction of blade-vortex interaction noise using higher harmonic pitch control

An acoustics test using an aeroelastically scaled rotor was conducted to examine the effectiveness of higher harmonic blade pitch control for the reduction of impulsive blade-vortex interaction (BVI) noise. A four-bladed, 110 in. diameter, articulated rotor model was tested in a heavy gas (Freon-12) medium in Langley's Transonic Dynamics Tunnel. Noise and vibration measurements were made for a range of matched flight conditions, where prescribed (open-loop) higher harmonic pitch was superimposed on the normal (baseline) collective and cyclic trim pitch. For the inflow-microphone noise measurements, advantage was taken of the reverberance in the hard walled tunnel by using a sound power determination approach. Initial findings from on-line data processing for three of the test microphones are reported for a 4/rev (4P) collective pitch control for a range of input amplitudes and phases. By comparing these results to corresponding baseline (no control) conditions, significant noise reductions (4 to 5 dB) were found for low-speed descent conditions, where helicopter BVI noise is most intense. For other rotor flight conditions, the overall noise was found to increase. All cases show increased vibration levels.

Brooks, Thomas F.↗

NASA NTRS1990

Reduction of blade-vortex interaction noise through higher harmonic pitch control

Brooks, Thomas F.↗

DOE OSTI2019

Citywide Impacts of E-Commerce: Does Parcel Delivery Travel Outweigh Household Shopping Travel Reductions?

E-commerce has facilitated online ordering of goods by households in recent years. This technological advancement has disrupted shopping related transportation. While the National Household Travel Survey (NHTS [1]) finds that household shopping frequency has declined in the last 10-20 years, deliveries by parcel delivery trucks and vans [2] have increased. However, the net effect of these phenomena on overall trip making, vehicle-miles traveled (VMT) and fuel consumption has not been quantified. From a regional planning perspective, understanding the net effect is important for informing city policies--for example, in regards to land use and transportation planning. The objective of this research is to address this gap. In this study, the net regional impact of e-commerce on transportation and fuel consumption is evaluated. The approach relies on a powerful, agent-based modeling framework (POLARIS [3]) that models decisions made by individual household and commercial agents. E-commerce demand is modeled for each household using a bilevel multinomial probit structure that evaluates e-commerce participation and ordering frequency. Last-mile delivery tours were constructed using GIS-based tools and information from a major parcel delivery company [4]. After integrating the resulting supply and demand models with all other passenger and commercial traffic within POLARIS, a traffic simulation was performed and subsequently VMT and energy consumption were analyzed. The study finds that while e-commerce has generated an increase in parcel truck delivery trips, the net effect of e-commerce is a reduction in VMT and fuel consumption due major reductions in these quantities via shopping trip reductions.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

NASA NTRS1981

A research program to reduce interior noise in general aviation airplanes. Influence of depressurization and damping material on the noise reduction characteristics of flat and curved stiffened panels

Some 20 x 20 aluminum panels were studied in a frequency range from 20 Hz to 5000 Hz. The noise sources used were a swept sine wave generator and a random noise generator. The effect of noise source was found to be negligible. Increasing the pressure differential across the panel gave better noise reduction below the fundamental resonance frequency due to an increase in stiffness. The largest increase occurred in the first 1 psi pressure differential. The curved, stiffened panel exhibited similar behavior, but with a lower increase of low frequency noise reduction. Depressurization on these panels resulted in decreased noise reduction at higher frequencies. The effect of damping tapes on the overall noise reduction values of the test specimens was small away from the resonance frequency. In the mass-law region, a slight and proportional improvement in noise reduction was observed by adding damping material. Adding sound absorbtion material to a panel with damping material beneficially increased noise reduction at high frequencies.

Navaneethan, R.↗

DOE OSTI2025

The Langdon effect in laser plasmas: Absorption and conduction

A plasma heated by inverse bremsstrahlung absorption of laser light develops a non-Maxwellian electron distribution function, called the Langdon effect [A. B. Langdon, Phys. Rev. Lett. 44, 575 (1980)]. These non-Maxwellian distributions are sufficiently long-lived to impact the absorption processes itself as well as the transport of heat by electrons. The theory of the Langdon effect in a homogeneous plasma is reviewed to clarify some aspects of Langdon's derivation as well as to confirm that the widely used super-Gaussian approximation works fairly well to describe the shape of the distribution function and reduction of the absorption rate. The Langdon effect on thermal conduction in an inhomogeneous plasma is developed by considering perturbations in a homogeneous absorbing plasma, which develops a heat flux due to both temperature and density gradients. A practical theory of the heat flux is developed by fitting the results of Vlasov–Fokker–Planck simulations, which avoids several approximations that compromised the usefulness of past theoretical predictions, most critically, the effect of electron–electron collisions on the fluxes. The present fits parameterize the coefficients of the temperature gradient (thermal conductivity) and the density gradient for a plasma of any ionization state and for any laser intensity where the theory of the Langdon effect remains locally valid. It is expected that this generalized theory of heat flow in an absorbing plasma will improve the predictive capability of radiation-hydrodynamics simulations of laser-produced plasmas, especially those formed in inertial confinement fusion experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1976

Effect of water and ice on strength and fracture toughness of intermittently bonded boron-epoxy composites

The effects of water and ice on the strength and fracture toughness of boron-epoxy composites with polyurethane intermittent bonding have been investigated. Neither simple soaking in water nor soaking followed by freezing and thawing have marked effects on the strength of the fully-coated composites, but they have disastrous effects on the uncoated composites. Toughness is affected only marginally, with some small reductions in the fully-coated samples, and with essentially no effect on the uncoated composites. An analysis is presented which explains adequately the experimental strength and toughness results obtained, and which is based on an argument that water absorption reduces the interfacial shear strength only of the uncoated areas and not those regions coated by the polyurethane varnish. The results indicate that the advantages of appropriate intermittent bonding (i.e., high strength combined with high toughness) are retained in wet conditions so that such composites may be favorably used in such adverse environmental conditions.

Atkins, A. G.↗

NASA NTRS1990

A reverse KREBS cycle in photosynthesis: consensus at last

The Krebs cycle (citric acid or tricarboxylic acid cycle), the final common pathway in aerobic metabolism for the oxidation of carbohydrates, fatty acids and amino acids, is known to be irreversible. It liberates CO2 and generates NADH whose aerobic oxidation yields ATP but it does not operate in reverse as a biosynthetic pathway for CO2 assimilation. In 1966, our laboratory described a cyclic pathway for CO2 assimilation (Evans, Buchanan and Arnon 1966) that was unusual in two respects: (i) it provided the first instance of an obligate photoautotroph that assimilated CO2 by a pathway different from Calvin's reductive pentose phosphate cycle (Calvin 1962) and (ii) in its overall effect the new cycle was a reversal of the Krebs cycle. Named the 'reductive carboxylic acid cycle' (sometimes also called the reductive tricarboxylic acid cycle) the new cycle appeared to be the sole CO2 assimilation pathway in Chlorobium thiosulfatophilum (Evans et al. 1966) (now known as Chlorobium limicola forma thiosulfatophilum). Chlorobium is a photosynthetic green sulfur bacterium that grows anaerobically in an inorganic medium with sulfide and thiosulfate as electron donors and CO2 as an obligatory carbon source. In the ensuing years, the new cycle was viewed with skepticism. Not only was it in conflict with the prevailing doctrine that the 'one important property ... shared by all (our emphasis) autotrophic species is the assimilation of CO2 via the Calvin cycle' (McFadden 1973) but also some of its experimental underpinnings were challenged. It is only now that in the words of one of its early skeptics (Tabita 1988) 'a long and tortuous controversy' has ended with general acceptance of the reductive carboxylic acid cycle as a photosynthetic CO2 assimilation pathway distinct from the pentose cycle. (Henceforth, to minimize repetitiveness, the reductive pentose phosphate cycle will often be referred to as the pentose cycle and the reductive carboxylic acid cycle as the carboxylic acid cycle.) Aside from photosynthetic pathways which are the focus of this article, CO2 assimilation is also known to sustain autotrophic growth via the acetyl-CoA pathway (Wood et al. 1986). Our aim here is to discuss (i) the findings that led our group to the discovery of the reductive carboxylic acid cycle, (ii) the nature and resolution of the controversy that followed, and (iii) the possible evolutionary implications of the cycle as an ancient mechanism for photosynthetic CO2 assimilation that preceded the pentose cycle and served as a precursor of the Krebs cycle in aerobic metabolism.

Non-NASA Center↗

DOE OSTI2021

Analysis of Ion-Exchanged ZSM-5, BEA, and SSZ-13 Zeolite Trapping Materials under Realistic Exhaust Conditions

An industry-defined evaluation protocol was used to evaluate the hydrocarbon trapping (HCT) and passive NOx adsorption (PNA) potential for BEA, ZSM-5, and SSZ-13 zeolites with ion-exchanged Pd or Ag. All materials underwent 700 °C degreening prior to exposure to an industry-derived protocol gas stream, which included NOx, ethylene, toluene, and decane as measured trapping species as well as common exhaust gasses CO, H2O, O2, CO2, and H2. Evaluation showed that BEA and ZSM-5 zeolites were effective at trapping hydrocarbons (HCs), as saturation was not achieved after 30 min of exposure. SSZ-13 also stored HCs but was only able to adsorb 20–25% compared to BEA and ZSM-5. The presence of Ag or Pd did not impact the overall HC uptake, particularly in the first three minutes. Pd/zeolites had significantly lower THC release temperature, and it aided in the conversion of the released HCs; Ag only had a moderate effect in both areas. With respect to NOx adsorption, the level of uptake was much lower than HCs on all samples, and Ag or Pd was necessary with Pd being notably more effective. Additionally, only Pd/ZSM-5 and Pd/SSZ-13 continue to store a portion of the NOx above 200 °C, which is critical for downstream selective catalytic NOx reduction (SCR). Hydrothermal aging (800 °C for 50 h) of a subset of the samples were performed: BEA, Pd/BEA, ZSM-5, Pd/ZSM-5, and Pd/SSZ-13. There was a minimal effect on the HC storage, ~10% reduction in capacity with no effect on release temperature; however, only Pd/SSZ-13 showed significant NOx storage after aging.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗